X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=Documentation%2FDMA-mapping.txt;h=01f24e94bdb630ddecb6511ffa0f02119ff54c55;hb=8365388827663bd6fb773e3623ed9023c0f82b1d;hp=c74fec8c2351168d1329c527183f3a975234030e;hpb=6675ce13ed783f88ea5d82f0d855462b76ff0dad;p=safe%2Fjmp%2Flinux-2.6

diff --git a/Documentation/DMA-mapping.txt b/Documentation/DMA-mapping.txt
index c74fec8..01f24e9 100644
--- a/Documentation/DMA-mapping.txt
+++ b/Documentation/DMA-mapping.txt
@@ -26,7 +26,7 @@ mapped only for the time they are actually used and unmapped after the DMA
 transfer.
 
 The following API will work of course even on platforms where no such
-hardware exists, see e.g. include/asm-i386/pci.h for how it is implemented on
+hardware exists, see e.g. arch/x86/include/asm/pci.h for how it is implemented on
 top of the virt_to_bus interface.
 
 First of all, you should make sure
@@ -136,7 +136,7 @@ exactly why.
 The standard 32-bit addressing PCI device would do something like
 this:
 
-	if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
+	if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
 		printk(KERN_WARNING
 		       "mydev: No suitable DMA available.\n");
 		goto ignore_this_device;
@@ -155,9 +155,9 @@ all 64-bits when accessing streaming DMA:
 
 	int using_dac;
 
-	if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
+	if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
 		using_dac = 1;
-	} else if (!pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
+	} else if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
 		using_dac = 0;
 	} else {
 		printk(KERN_WARNING
@@ -170,14 +170,14 @@ the case would look like this:
 
 	int using_dac, consistent_using_dac;
 
-	if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
+	if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
 		using_dac = 1;
 	   	consistent_using_dac = 1;
-		pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
-	} else if (!pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
+		pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+	} else if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
 		using_dac = 0;
 		consistent_using_dac = 0;
-		pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
+		pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
 	} else {
 		printk(KERN_WARNING
 		       "mydev: No suitable DMA available.\n");
@@ -192,7 +192,7 @@ check the return value from pci_set_consistent_dma_mask().
 Finally, if your device can only drive the low 24-bits of
 address during PCI bus mastering you might do something like:
 
-	if (pci_set_dma_mask(pdev, DMA_24BIT_MASK)) {
+	if (pci_set_dma_mask(pdev, DMA_BIT_MASK(24))) {
 		printk(KERN_WARNING
 		       "mydev: 24-bit DMA addressing not available.\n");
 		goto ignore_this_device;
@@ -213,7 +213,7 @@ most specific mask.
 
 Here is pseudo-code showing how this might be done:
 
-	#define PLAYBACK_ADDRESS_BITS	DMA_32BIT_MASK
+	#define PLAYBACK_ADDRESS_BITS	DMA_BIT_MASK(32)
 	#define RECORD_ADDRESS_BITS	0x00ffffff
 
 	struct my_sound_card *card;