-# drivers/sound/Config.in
-#
# 18 Apr 1998, Michael Elizabeth Chastain, <mailto:mec@shout.net>
# More hacking for modularisation.
#
config SOUND_BCM_CS4297A
tristate "Crystal Sound CS4297a (for Swarm)"
- depends on SOUND_PRIME && SIBYTE_SWARM
+ depends on SIBYTE_SWARM
help
The BCM91250A has a Crystal CS4297a on synchronous serial
port B (in addition to the DB-9 serial port). Say Y or M
config SOUND_VWSND
tristate "SGI Visual Workstation Sound"
- depends on SOUND_PRIME && X86_VISWS
+ depends on X86_VISWS
help
Say Y or M if you have an SGI Visual Workstation and you want to be
able to use its on-board audio. Read
<file:Documentation/sound/oss/vwsnd> for more info on this driver's
capabilities.
-config SOUND_HAL2
- tristate "SGI HAL2 sound (EXPERIMENTAL)"
- depends on SOUND_PRIME && SGI_IP22 && EXPERIMENTAL
- help
- Say Y or M if you have an SGI Indy or Indigo2 system and want to be able to
- use its on-board A2 audio system.
-
config SOUND_AU1550_AC97
tristate "Au1550/Au1200 AC97 Sound"
- select SND_AC97_CODEC
- depends on SOUND_PRIME && (SOC_AU1550 || SOC_AU1200)
-
-config SOUND_TRIDENT
- tristate "Trident 4DWave DX/NX, SiS 7018 or ALi 5451 PCI Audio Core"
- depends on SOUND_PRIME && PCI
- ---help---
- Say Y or M if you have a PCI sound card utilizing the Trident
- 4DWave-DX/NX chipset or your mother board chipset has SiS 7018
- or ALi 5451 built-in. The SiS 7018 PCI Audio Core is embedded
- in SiS960 Super South Bridge and SiS540/630 Single Chipset.
- The ALi 5451 PCI Audio Core is embedded in ALi M1535, M1535D,
- M1535+ or M1535D+ South Bridge.
-
- Use lspci -n to find out if your sound card or chipset uses
- Trident 4DWave or SiS 7018. PCI ID 1023:2000 or 1023:2001 stands
- for Trident 4Dwave. PCI ID 1039:7018 stands for SiS7018. PCI ID
- 10B9:5451 stands for ALi5451.
-
- This driver supports S/PDIF in/out (record/playback) for ALi 5451
- embedded in ALi M1535+ and M1535D+. Note that they aren't all
- enabled by default; you can enable them by saying Y to "/proc file
- system support" and "Sysctl support", and after the /proc file
- system has been mounted, executing the command
-
- command what is enabled
-
- echo 0>/proc/ALi5451 pcm out is also set to S/PDIF out. (Default).
-
- echo 1>/proc/ALi5451 use S/PDIF out to output pcm data.
-
- echo 2>/proc/ALi5451 use S/PDIF out to output non-pcm data.
- (AC3...).
-
- echo 3>/proc/ALi5451 record from Ac97 in(MIC, Line in...).
- (Default).
-
- echo 4>/proc/ALi5451 no matter Ac97 settings, record from S/PDIF
- in.
-
-
- This driver differs slightly from OSS/Free, so PLEASE READ the
- comments at the top of <file:sound/oss/trident.c>.
+ depends on SOC_AU1550 || SOC_AU1200
config SOUND_MSNDCLAS
tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey"
- depends on SOUND_PRIME && (m || !STANDALONE)
+ depends on (m || !STANDALONE) && ISA
help
Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or
Monterey (not for the Pinnacle or Fiji).
config SOUND_MSNDPIN
tristate "Support for Turtle Beach MultiSound Pinnacle, Fiji"
- depends on SOUND_PRIME && (m || !STANDALONE)
+ depends on (m || !STANDALONE) && ISA
help
Say M here if you have a Turtle Beach MultiSound Pinnacle or Fiji.
See <file:Documentation/sound/oss/MultiSound> for important information
configure the card's resources.
comment "MSND Pinnacle DSP section will be configured to above parameters."
- depends on SOUND_PRIME && SOUND_MSNDPIN=y && MSNDPIN_NONPNP
+ depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP
config MSNDPIN_CFG
hex "MSND Pinnacle config port 250,260,270"
Mode".
comment "Pinnacle-specific Device Configuration (0 disables)"
- depends on SOUND_PRIME && SOUND_MSNDPIN=y && MSNDPIN_NONPNP
+ depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP
config MSNDPIN_MPU_IO
hex "MSND Pinnacle MPU I/O (e.g. 330)"
config MSND_FIFOSIZE
int "MSND buffer size (kB)"
- depends on SOUND_PRIME && (SOUND_MSNDPIN=y || SOUND_MSNDCLAS=y)
+ depends on SOUND_MSNDPIN=y || SOUND_MSNDCLAS=y
default "128"
help
Configures the size of each audio buffer, in kilobytes, for
and Pinnacle). Larger values reduce the chance of data overruns at
the expense of overall latency. If unsure, use the default.
-config SOUND_OSS
+menuconfig SOUND_OSS
tristate "OSS sound modules"
- depends on SOUND_PRIME && ISA_DMA_API && VIRT_TO_BUS
+ depends on ISA_DMA_API && VIRT_TO_BUS
help
OSS is the Open Sound System suite of sound card drivers. They make
sound programming easier since they provide a common API. Say Y or
driver for your sound card above, then pick your driver from the
list below.
+if SOUND_OSS
+
config SOUND_TRACEINIT
bool "Verbose initialisation"
- depends on SOUND_OSS
help
Verbose soundcard initialization -- affects the format of autoprobe
and initialization messages at boot time.
config SOUND_DMAP
bool "Persistent DMA buffers"
- depends on SOUND_OSS
---help---
Linux can often have problems allocating DMA buffers for ISA sound
cards on machines with more than 16MB of RAM. This is because ISA
Say Y unless you have 16MB or more RAM or a PCI sound card.
-config SOUND_SSCAPE
- tristate "Ensoniq SoundScape support"
- depends on SOUND_OSS
- depends on VIRT_TO_BUS
- help
- Answer Y if you have a sound card based on the Ensoniq SoundScape
- chipset. Such cards are being manufactured at least by Ensoniq, Spea
- and Reveal (Reveal makes also other cards).
-
- If you compile the driver into the kernel, you have to add
- "sscape=<io>,<irq>,<dma>,<mpuio>,<mpuirq>" to the kernel command
- line.
-
-
config SOUND_VMIDI
tristate "Loopback MIDI device support"
- depends on SOUND_OSS
help
Support for MIDI loopback on port 1 or 2.
config SOUND_TRIX
tristate "MediaTrix AudioTrix Pro support"
- depends on SOUND_OSS
help
Answer Y if you have the AudioTriX Pro sound card manufactured
by MediaTrix.
config SOUND_MSS
tristate "Microsoft Sound System support"
- depends on SOUND_OSS
---help---
Again think carefully before answering Y to this question. It's
safe to answer Y if you have the original Windows Sound System card
config SOUND_MPU401
tristate "MPU-401 support (NOT for SB16)"
- depends on SOUND_OSS
---help---
Be careful with this question. The MPU401 interface is supported by
all sound cards. However, some natively supported cards have their
config SOUND_PAS
tristate "ProAudioSpectrum 16 support"
- depends on SOUND_OSS
---help---
Answer Y only if you have a Pro Audio Spectrum 16, ProAudio Studio
16 or Logitech SoundMan 16 sound card. Answer N if you have some
config SOUND_PSS
tristate "PSS (AD1848, ADSP-2115, ESC614) support"
- depends on SOUND_OSS
help
Answer Y or M if you have an Orchid SW32, Cardinal DSP16, Beethoven
ADSP-16 or some other card based on the PSS chipset (AD1848 codec +
config SOUND_SB
tristate "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
- depends on SOUND_OSS
---help---
Answer Y if you have an original Sound Blaster card made by Creative
Labs or a 100% hardware compatible clone (like the Thunderboard or
config SOUND_YM3812
tristate "Yamaha FM synthesizer (YM3812/OPL-3) support"
- depends on SOUND_OSS
---help---
Answer Y if your card has a FM chip made by Yamaha (OPL2/OPL3/OPL4).
Answering Y is usually a safe and recommended choice, however some
config SOUND_UART6850
tristate "6850 UART support"
- depends on SOUND_OSS
help
This option enables support for MIDI interfaces based on the 6850
UART chip. This interface is rarely found on sound cards. It's safe
config SOUND_AEDSP16
tristate "Gallant Audio Cards (SC-6000 and SC-6600 based)"
- depends on SOUND_OSS
---help---
Answer Y if you have a Gallant's Audio Excel DSP 16 card. This
driver supports Audio Excel DSP 16 but not the III nor PnP versions
Base I/O port address for the CD-ROM interface of the Audio Excel
DSP 16 card.
-choice
- prompt "Audio Excel DSP 16"
- optional
- depends on SOUND_AEDSP16
-
-config AEDSP16_MSS
- bool "MSS emulation"
- depends on SOUND_MSS
- help
- Answer Y if you want your audio card to emulate Microsoft Sound
- System. You should then say Y to "Microsoft Sound System support"
- and say N to "Audio Excel DSP 16 (SBPro emulation)".
-
-config AEDSP16_SBPRO
- bool "SBPro emulation"
- depends on SOUND_SB
- help
- Answer Y if you want your audio card to emulate Sound Blaster Pro.
- You should then say Y to "100% Sound Blaster compatibles
- (SB16/32/64, ESS, Jazz16) support" and N to "Audio Excel DSP 16 (MSS
- emulation)".
-
- If you compile the driver into the kernel, you have to add
- "aedsp16=<io>,<irq>,<dma>,<mssio>,<mpuio>,<mouirq>" to the kernel
- command line.
-
-endchoice
-
config SOUND_VIDC
tristate "VIDC 16-bit sound"
- depends on ARM && (ARCH_ACORN || ARCH_CLPS7500) && SOUND_OSS
+ depends on ARM && (ARCH_ACORN || ARCH_CLPS7500)
help
16-bit support for the VIDC onboard sound hardware found on Acorn
machines.
config SOUND_WAVEARTIST
tristate "Netwinder WaveArtist"
- depends on ARM && SOUND_OSS && ARCH_NETWINDER
+ depends on ARM && ARCH_NETWINDER
help
Say Y here to include support for the Rockwell WaveArtist sound
system. This driver is mainly for the NetWinder.
tristate "XpressAudio Sound Blaster emulation"
depends on SOUND_SB
+endif # SOUND_OSS
+
config SOUND_SH_DAC_AUDIO
tristate "SuperH DAC audio support"
- depends on SOUND_PRIME && CPU_SH3
+ depends on CPU_SH3 && HIGH_RES_TIMERS
config SOUND_SH_DAC_AUDIO_CHANNEL
int "DAC channel"
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff