* exhibited a worse failed frames behaviour and we'll choose the highest rate
* whose failed frames behaviour is not worse than the one of the original rate
* target. While at it, check that the new rate is valid. */
-static void rate_control_pid_adjust_rate(struct ieee80211_local *local,
- struct sta_info *sta, int adj,
+static void rate_control_pid_adjust_rate(struct ieee80211_supported_band *sband,
+ struct ieee80211_sta *sta,
+ struct rc_pid_sta_info *spinfo, int adj,
struct rc_pid_rateinfo *rinfo)
{
- struct ieee80211_sub_if_data *sdata;
- struct ieee80211_supported_band *sband;
int cur_sorted, new_sorted, probe, tmp, n_bitrates, band;
- int cur = sta->txrate_idx;
+ int cur = spinfo->txrate_idx;
- sdata = sta->sdata;
- sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
band = sband->band;
n_bitrates = sband->n_bitrates;
/* Fit the rate found to the nearest supported rate. */
do {
if (rate_supported(sta, band, rinfo[tmp].index)) {
- sta->txrate_idx = rinfo[tmp].index;
+ spinfo->txrate_idx = rinfo[tmp].index;
break;
}
if (adj < 0)
} while (tmp < n_bitrates && tmp >= 0);
#ifdef CONFIG_MAC80211_DEBUGFS
- rate_control_pid_event_rate_change(
- &((struct rc_pid_sta_info *)sta->rate_ctrl_priv)->events,
- sta->txrate_idx, sband->bitrates[sta->txrate_idx].bitrate);
+ rate_control_pid_event_rate_change(&spinfo->events,
+ spinfo->txrate_idx,
+ sband->bitrates[spinfo->txrate_idx].bitrate);
#endif
}
}
static void rate_control_pid_sample(struct rc_pid_info *pinfo,
- struct ieee80211_local *local,
- struct sta_info *sta)
+ struct ieee80211_supported_band *sband,
+ struct ieee80211_sta *sta,
+ struct rc_pid_sta_info *spinfo)
{
-#ifdef CONFIG_MAC80211_MESH
- struct ieee80211_sub_if_data *sdata = sta->sdata;
-#endif
- struct rc_pid_sta_info *spinfo = sta->rate_ctrl_priv;
struct rc_pid_rateinfo *rinfo = pinfo->rinfo;
- struct ieee80211_supported_band *sband;
u32 pf;
s32 err_avg;
u32 err_prop;
int adj, i, j, tmp;
unsigned long period;
- sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
- spinfo = sta->rate_ctrl_priv;
-
/* In case nothing happened during the previous control interval, turn
* the sharpening factor on. */
period = (HZ * pinfo->sampling_period + 500) / 1000;
* still a good measurement and copy it. */
if (unlikely(spinfo->tx_num_xmit == 0))
pf = spinfo->last_pf;
- else {
+ else
pf = spinfo->tx_num_failed * 100 / spinfo->tx_num_xmit;
-#ifdef CONFIG_MAC80211_MESH
- if (pf == 100 &&
- sdata->vif.type == IEEE80211_IF_TYPE_MESH_POINT)
- mesh_plink_broken(sta);
-#endif
- pf <<= RC_PID_ARITH_SHIFT;
- sta->fail_avg = ((pf + (spinfo->last_pf << 3)) / 9)
- >> RC_PID_ARITH_SHIFT;
- }
spinfo->tx_num_xmit = 0;
spinfo->tx_num_failed = 0;
/* If we just switched rate, update the rate behaviour info. */
- if (pinfo->oldrate != sta->txrate_idx) {
+ if (pinfo->oldrate != spinfo->txrate_idx) {
i = rinfo[pinfo->oldrate].rev_index;
- j = rinfo[sta->txrate_idx].rev_index;
+ j = rinfo[spinfo->txrate_idx].rev_index;
tmp = (pf - spinfo->last_pf);
tmp = RC_PID_DO_ARITH_RIGHT_SHIFT(tmp, RC_PID_ARITH_SHIFT);
rinfo[j].diff = rinfo[i].diff + tmp;
- pinfo->oldrate = sta->txrate_idx;
+ pinfo->oldrate = spinfo->txrate_idx;
}
rate_control_pid_normalize(pinfo, sband->n_bitrates);
/* Change rate. */
if (adj)
- rate_control_pid_adjust_rate(local, sta, adj, rinfo);
+ rate_control_pid_adjust_rate(sband, sta, spinfo, adj, rinfo);
}
-static void rate_control_pid_tx_status(void *priv, struct net_device *dev,
- struct sk_buff *skb,
- struct ieee80211_tx_status *status)
+static void rate_control_pid_tx_status(void *priv, struct ieee80211_supported_band *sband,
+ struct ieee80211_sta *sta, void *priv_sta,
+ struct sk_buff *skb)
{
- struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
- struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
- struct ieee80211_sub_if_data *sdata;
struct rc_pid_info *pinfo = priv;
- struct sta_info *sta;
- struct rc_pid_sta_info *spinfo;
+ struct rc_pid_sta_info *spinfo = priv_sta;
unsigned long period;
- struct ieee80211_supported_band *sband;
-
- rcu_read_lock();
+ struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
- sta = sta_info_get(local, hdr->addr1);
- sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
-
- if (!sta)
- goto unlock;
-
- /* Don't update the state if we're not controlling the rate. */
- sdata = sta->sdata;
- if (sdata->bss && sdata->bss->force_unicast_rateidx > -1) {
- sta->txrate_idx = sdata->bss->max_ratectrl_rateidx;
- goto unlock;
- }
+ if (!spinfo)
+ return;
/* Ignore all frames that were sent with a different rate than the rate
* we currently advise mac80211 to use. */
- if (status->control.tx_rate != &sband->bitrates[sta->txrate_idx])
- goto unlock;
+ if (info->status.rates[0].idx != spinfo->txrate_idx)
+ return;
- spinfo = sta->rate_ctrl_priv;
spinfo->tx_num_xmit++;
#ifdef CONFIG_MAC80211_DEBUGFS
- rate_control_pid_event_tx_status(&spinfo->events, status);
+ rate_control_pid_event_tx_status(&spinfo->events, info);
#endif
/* We count frames that totally failed to be transmitted as two bad
* frames, those that made it out but had some retries as one good and
* one bad frame. */
- if (status->excessive_retries) {
+ if (!(info->flags & IEEE80211_TX_STAT_ACK)) {
spinfo->tx_num_failed += 2;
spinfo->tx_num_xmit++;
- } else if (status->retry_count) {
+ } else if (info->status.rates[0].count > 1) {
spinfo->tx_num_failed++;
spinfo->tx_num_xmit++;
}
- if (status->excessive_retries) {
- sta->tx_retry_failed++;
- sta->tx_num_consecutive_failures++;
- sta->tx_num_mpdu_fail++;
- } else {
- sta->tx_num_consecutive_failures = 0;
- sta->tx_num_mpdu_ok++;
- }
- sta->tx_retry_count += status->retry_count;
- sta->tx_num_mpdu_fail += status->retry_count;
-
/* Update PID controller state. */
period = (HZ * pinfo->sampling_period + 500) / 1000;
if (!period)
period = 1;
if (time_after(jiffies, spinfo->last_sample + period))
- rate_control_pid_sample(pinfo, local, sta);
-
- unlock:
- rcu_read_unlock();
+ rate_control_pid_sample(pinfo, sband, sta, spinfo);
}
-static void rate_control_pid_get_rate(void *priv, struct net_device *dev,
- struct ieee80211_supported_band *sband,
- struct sk_buff *skb,
- struct rate_selection *sel)
+static void
+rate_control_pid_get_rate(void *priv, struct ieee80211_sta *sta,
+ void *priv_sta,
+ struct ieee80211_tx_rate_control *txrc)
{
- struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
- struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
- struct ieee80211_sub_if_data *sdata;
- struct sta_info *sta;
+ struct sk_buff *skb = txrc->skb;
+ struct ieee80211_supported_band *sband = txrc->sband;
+ struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+ struct rc_pid_sta_info *spinfo = priv_sta;
int rateidx;
- u16 fc;
-
- rcu_read_lock();
- sta = sta_info_get(local, hdr->addr1);
+ if (txrc->rts)
+ info->control.rates[0].count =
+ txrc->hw->conf.long_frame_max_tx_count;
+ else
+ info->control.rates[0].count =
+ txrc->hw->conf.short_frame_max_tx_count;
- /* Send management frames and broadcast/multicast data using lowest
- * rate. */
- fc = le16_to_cpu(hdr->frame_control);
- if ((fc & IEEE80211_FCTL_FTYPE) != IEEE80211_FTYPE_DATA ||
- is_multicast_ether_addr(hdr->addr1) || !sta) {
- sel->rate = rate_lowest(local, sband, sta);
- rcu_read_unlock();
+ /* Send management frames and NO_ACK data using lowest rate. */
+ if (rate_control_send_low(sta, priv_sta, txrc))
return;
- }
- /* If a forced rate is in effect, select it. */
- sdata = IEEE80211_DEV_TO_SUB_IF(dev);
- if (sdata->bss && sdata->bss->force_unicast_rateidx > -1)
- sta->txrate_idx = sdata->bss->force_unicast_rateidx;
-
- rateidx = sta->txrate_idx;
+ rateidx = spinfo->txrate_idx;
if (rateidx >= sband->n_bitrates)
rateidx = sband->n_bitrates - 1;
- sta->last_txrate_idx = rateidx;
-
- rcu_read_unlock();
-
- sel->rate = &sband->bitrates[rateidx];
+ info->control.rates[0].idx = rateidx;
#ifdef CONFIG_MAC80211_DEBUGFS
- rate_control_pid_event_tx_rate(
- &((struct rc_pid_sta_info *) sta->rate_ctrl_priv)->events,
+ rate_control_pid_event_tx_rate(&spinfo->events,
rateidx, sband->bitrates[rateidx].bitrate);
#endif
}
-static void rate_control_pid_rate_init(void *priv, void *priv_sta,
- struct ieee80211_local *local,
- struct sta_info *sta)
+static void
+rate_control_pid_rate_init(void *priv, struct ieee80211_supported_band *sband,
+ struct ieee80211_sta *sta, void *priv_sta)
{
+ struct rc_pid_sta_info *spinfo = priv_sta;
+ struct rc_pid_info *pinfo = priv;
+ struct rc_pid_rateinfo *rinfo = pinfo->rinfo;
+ int i, j, tmp;
+ bool s;
+
/* TODO: This routine should consider using RSSI from previous packets
* as we need to have IEEE 802.1X auth succeed immediately after assoc..
* Until that method is implemented, we will use the lowest supported
* rate as a workaround. */
- struct ieee80211_supported_band *sband;
- sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
- sta->txrate_idx = rate_lowest_index(local, sband, sta);
- sta->fail_avg = 0;
+ /* Sort the rates. This is optimized for the most common case (i.e.
+ * almost-sorted CCK+OFDM rates). Kind of bubble-sort with reversed
+ * mapping too. */
+ for (i = 0; i < sband->n_bitrates; i++) {
+ rinfo[i].index = i;
+ rinfo[i].rev_index = i;
+ if (RC_PID_FAST_START)
+ rinfo[i].diff = 0;
+ else
+ rinfo[i].diff = i * pinfo->norm_offset;
+ }
+ for (i = 1; i < sband->n_bitrates; i++) {
+ s = 0;
+ for (j = 0; j < sband->n_bitrates - i; j++)
+ if (unlikely(sband->bitrates[rinfo[j].index].bitrate >
+ sband->bitrates[rinfo[j + 1].index].bitrate)) {
+ tmp = rinfo[j].index;
+ rinfo[j].index = rinfo[j + 1].index;
+ rinfo[j + 1].index = tmp;
+ rinfo[rinfo[j].index].rev_index = j;
+ rinfo[rinfo[j + 1].index].rev_index = j + 1;
+ s = 1;
+ }
+ if (!s)
+ break;
+ }
+
+ spinfo->txrate_idx = rate_lowest_index(sband, sta);
}
-static void *rate_control_pid_alloc(struct ieee80211_local *local)
+static void *rate_control_pid_alloc(struct ieee80211_hw *hw,
+ struct dentry *debugfsdir)
{
struct rc_pid_info *pinfo;
struct rc_pid_rateinfo *rinfo;
struct ieee80211_supported_band *sband;
- int i, j, tmp;
- bool s;
+ int i, max_rates = 0;
#ifdef CONFIG_MAC80211_DEBUGFS
struct rc_pid_debugfs_entries *de;
#endif
- sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
-
pinfo = kmalloc(sizeof(*pinfo), GFP_ATOMIC);
if (!pinfo)
return NULL;
- /* We can safely assume that sband won't change unless we get
- * reinitialized. */
- rinfo = kmalloc(sizeof(*rinfo) * sband->n_bitrates, GFP_ATOMIC);
+ for (i = 0; i < IEEE80211_NUM_BANDS; i++) {
+ sband = hw->wiphy->bands[i];
+ if (sband && sband->n_bitrates > max_rates)
+ max_rates = sband->n_bitrates;
+ }
+
+ rinfo = kmalloc(sizeof(*rinfo) * max_rates, GFP_ATOMIC);
if (!rinfo) {
kfree(pinfo);
return NULL;
pinfo->rinfo = rinfo;
pinfo->oldrate = 0;
- /* Sort the rates. This is optimized for the most common case (i.e.
- * almost-sorted CCK+OFDM rates). Kind of bubble-sort with reversed
- * mapping too. */
- for (i = 0; i < sband->n_bitrates; i++) {
- rinfo[i].index = i;
- rinfo[i].rev_index = i;
- if (RC_PID_FAST_START)
- rinfo[i].diff = 0;
- else
- rinfo[i].diff = i * pinfo->norm_offset;
- }
- for (i = 1; i < sband->n_bitrates; i++) {
- s = 0;
- for (j = 0; j < sband->n_bitrates - i; j++)
- if (unlikely(sband->bitrates[rinfo[j].index].bitrate >
- sband->bitrates[rinfo[j + 1].index].bitrate)) {
- tmp = rinfo[j].index;
- rinfo[j].index = rinfo[j + 1].index;
- rinfo[j + 1].index = tmp;
- rinfo[rinfo[j].index].rev_index = j;
- rinfo[rinfo[j + 1].index].rev_index = j + 1;
- s = 1;
- }
- if (!s)
- break;
- }
-
#ifdef CONFIG_MAC80211_DEBUGFS
de = &pinfo->dentries;
- de->dir = debugfs_create_dir("rc80211_pid",
- local->hw.wiphy->debugfsdir);
de->target = debugfs_create_u32("target_pf", S_IRUSR | S_IWUSR,
- de->dir, &pinfo->target);
+ debugfsdir, &pinfo->target);
de->sampling_period = debugfs_create_u32("sampling_period",
- S_IRUSR | S_IWUSR, de->dir,
+ S_IRUSR | S_IWUSR, debugfsdir,
&pinfo->sampling_period);
de->coeff_p = debugfs_create_u32("coeff_p", S_IRUSR | S_IWUSR,
- de->dir, &pinfo->coeff_p);
+ debugfsdir, (u32 *)&pinfo->coeff_p);
de->coeff_i = debugfs_create_u32("coeff_i", S_IRUSR | S_IWUSR,
- de->dir, &pinfo->coeff_i);
+ debugfsdir, (u32 *)&pinfo->coeff_i);
de->coeff_d = debugfs_create_u32("coeff_d", S_IRUSR | S_IWUSR,
- de->dir, &pinfo->coeff_d);
+ debugfsdir, (u32 *)&pinfo->coeff_d);
de->smoothing_shift = debugfs_create_u32("smoothing_shift",
- S_IRUSR | S_IWUSR, de->dir,
+ S_IRUSR | S_IWUSR, debugfsdir,
&pinfo->smoothing_shift);
de->sharpen_factor = debugfs_create_u32("sharpen_factor",
- S_IRUSR | S_IWUSR, de->dir,
+ S_IRUSR | S_IWUSR, debugfsdir,
&pinfo->sharpen_factor);
de->sharpen_duration = debugfs_create_u32("sharpen_duration",
- S_IRUSR | S_IWUSR, de->dir,
+ S_IRUSR | S_IWUSR, debugfsdir,
&pinfo->sharpen_duration);
de->norm_offset = debugfs_create_u32("norm_offset",
- S_IRUSR | S_IWUSR, de->dir,
+ S_IRUSR | S_IWUSR, debugfsdir,
&pinfo->norm_offset);
#endif
debugfs_remove(de->coeff_p);
debugfs_remove(de->sampling_period);
debugfs_remove(de->target);
- debugfs_remove(de->dir);
#endif
kfree(pinfo->rinfo);
kfree(pinfo);
}
-static void rate_control_pid_clear(void *priv)
-{
-}
-
-static void *rate_control_pid_alloc_sta(void *priv, gfp_t gfp)
+static void *rate_control_pid_alloc_sta(void *priv, struct ieee80211_sta *sta,
+ gfp_t gfp)
{
struct rc_pid_sta_info *spinfo;
return spinfo;
}
-static void rate_control_pid_free_sta(void *priv, void *priv_sta)
+static void rate_control_pid_free_sta(void *priv, struct ieee80211_sta *sta,
+ void *priv_sta)
{
- struct rc_pid_sta_info *spinfo = priv_sta;
- kfree(spinfo);
+ kfree(priv_sta);
}
static struct rate_control_ops mac80211_rcpid = {
.tx_status = rate_control_pid_tx_status,
.get_rate = rate_control_pid_get_rate,
.rate_init = rate_control_pid_rate_init,
- .clear = rate_control_pid_clear,
.alloc = rate_control_pid_alloc,
.free = rate_control_pid_free,
.alloc_sta = rate_control_pid_alloc_sta,
#endif
};
-MODULE_DESCRIPTION("PID controller based rate control algorithm");
-MODULE_AUTHOR("Stefano Brivio");
-MODULE_AUTHOR("Mattias Nissler");
-MODULE_LICENSE("GPL");
-
int __init rc80211_pid_init(void)
{
return ieee80211_rate_control_register(&mac80211_rcpid);
{
ieee80211_rate_control_unregister(&mac80211_rcpid);
}
-
-#ifdef CONFIG_MAC80211_RC_PID_MODULE
-module_init(rc80211_pid_init);
-module_exit(rc80211_pid_exit);
-#endif