config MAC80211
tristate "Generic IEEE 802.11 Networking Stack (mac80211)"
- depends on EXPERIMENTAL
+ depends on CFG80211
select CRYPTO
select CRYPTO_ECB
select CRYPTO_ARC4
select CRYPTO_AES
select CRC32
- select WIRELESS_EXT
- select CFG80211
- select NET_SCH_FIFO
---help---
- This option enables the hardware independent IEEE 802.11
- networking stack.
+ This option enables the hardware independent IEEE 802.11
+ networking stack.
+
+comment "CFG80211 needs to be enabled for MAC80211"
+ depends on CFG80211=n
+
+if MAC80211 != n
+
+config MAC80211_RC_PID
+ bool "PID controller based rate control algorithm" if EMBEDDED
+ ---help---
+ This option enables a TX rate control algorithm for
+ mac80211 that uses a PID controller to select the TX
+ rate.
+
+config MAC80211_RC_MINSTREL
+ bool "Minstrel" if EMBEDDED
+ default y
+ ---help---
+ This option enables the 'minstrel' TX rate control algorithm
+
+choice
+ prompt "Default rate control algorithm"
+ default MAC80211_RC_DEFAULT_MINSTREL
+ ---help---
+ This option selects the default rate control algorithm
+ mac80211 will use. Note that this default can still be
+ overridden through the ieee80211_default_rc_algo module
+ parameter if different algorithms are available.
+
+config MAC80211_RC_DEFAULT_PID
+ bool "PID controller based rate control algorithm"
+ depends on MAC80211_RC_PID
+ ---help---
+ Select the PID controller based rate control as the
+ default rate control algorithm. You should choose
+ this unless you know what you are doing.
+
+config MAC80211_RC_DEFAULT_MINSTREL
+ bool "Minstrel"
+ depends on MAC80211_RC_MINSTREL
+ ---help---
+ Select Minstrel as the default rate control algorithm.
+
+
+endchoice
+
+config MAC80211_RC_DEFAULT
+ string
+ default "minstrel" if MAC80211_RC_DEFAULT_MINSTREL
+ default "pid" if MAC80211_RC_DEFAULT_PID
+ default ""
+
+endif
+
+config MAC80211_MESH
+ bool "Enable mac80211 mesh networking (pre-802.11s) support"
+ depends on MAC80211 && EXPERIMENTAL
+ ---help---
+ This options enables support of Draft 802.11s mesh networking.
+ The implementation is based on Draft 2.08 of the Mesh Networking
+ amendment. However, no compliance with that draft is claimed or even
+ possible, as drafts leave a number of identifiers to be defined after
+ ratification. For more information visit http://o11s.org/.
config MAC80211_LEDS
bool "Enable LED triggers"
- depends on MAC80211 && LEDS_TRIGGERS
+ depends on MAC80211
+ select NEW_LEDS
+ select LEDS_TRIGGERS
+ ---help---
+ This option enables a few LED triggers for different
+ packet receive/transmit events.
+
+config MAC80211_DEBUGFS
+ bool "Export mac80211 internals in DebugFS"
+ depends on MAC80211 && DEBUG_FS
---help---
- This option enables a few LED triggers for different
- packet receive/transmit events.
+ Select this to see extensive information about
+ the internal state of mac80211 in debugfs.
-config MAC80211_DEBUG
- bool "Enable debugging output"
+ Say N unless you know you need this.
+
+menuconfig MAC80211_DEBUG_MENU
+ bool "Select mac80211 debugging features"
depends on MAC80211
---help---
- This option will enable debug tracing output for the
- ieee80211 network stack.
+ This option collects various mac80211 debug settings.
+
+config MAC80211_DEBUG_PACKET_ALIGNMENT
+ bool "Enable packet alignment debugging"
+ depends on MAC80211_DEBUG_MENU
+ ---help---
+ This option is recommended for driver authors and strongly
+ discouraged for everybody else, it will trigger a warning
+ when a driver hands mac80211 a buffer that is aligned in
+ a way that will cause problems with the IP stack on some
+ architectures.
+
+ Say N unless you're writing a mac80211 based driver.
+
+config MAC80211_NOINLINE
+ bool "Do not inline TX/RX handlers"
+ depends on MAC80211_DEBUG_MENU
+ ---help---
+ This option affects code generation in mac80211, when
+ selected some functions are marked "noinline" to allow
+ easier debugging of problems in the transmit and receive
+ paths.
+
+ This option increases code size a bit and inserts a lot
+ of function calls in the code, but is otherwise safe to
+ enable.
- If you are not trying to debug or develop the ieee80211
- subsystem, you most likely want to say N here.
+ If unsure, say N unless you expect to be finding problems
+ in mac80211.
config MAC80211_VERBOSE_DEBUG
bool "Verbose debugging output"
- depends on MAC80211_DEBUG
+ depends on MAC80211_DEBUG_MENU
+ ---help---
+ Selecting this option causes mac80211 to print out
+ many debugging messages. It should not be selected
+ on production systems as some of the messages are
+ remotely triggerable.
-config MAC80211_LOWTX_FRAME_DUMP
- bool "Debug frame dumping"
- depends on MAC80211_DEBUG
+ Do not select this option.
+
+config MAC80211_HT_DEBUG
+ bool "Verbose HT debugging"
+ depends on MAC80211_DEBUG_MENU
---help---
- Selecting this option will cause the stack to
- print a message for each frame that is handed
- to the lowlevel driver for transmission. This
- message includes all MAC addresses and the
- frame control field.
+ This option enables 802.11n High Throughput features
+ debug tracing output.
- If unsure, say N and insert the debugging code
- you require into the driver you are debugging.
+ It should not be selected on production systems as some
+ of the messages are remotely triggerable.
-config TKIP_DEBUG
- bool "TKIP debugging"
- depends on MAC80211_DEBUG
+ Do not select this option.
-config MAC80211_DEBUG_COUNTERS
- bool "Extra statistics for TX/RX debugging"
- depends on MAC80211_DEBUG
+config MAC80211_TKIP_DEBUG
+ bool "Verbose TKIP debugging"
+ depends on MAC80211_DEBUG_MENU
+ ---help---
+ Selecting this option causes mac80211 to print out
+ very verbose TKIP debugging messages. It should not
+ be selected on production systems as those messages
+ are remotely triggerable.
+
+ Do not select this option.
config MAC80211_IBSS_DEBUG
- bool "Support for IBSS testing"
- depends on MAC80211_DEBUG
+ bool "Verbose IBSS debugging"
+ depends on MAC80211_DEBUG_MENU
---help---
- Say Y here if you intend to debug the IBSS code.
+ Selecting this option causes mac80211 to print out
+ very verbose IBSS debugging messages. It should not
+ be selected on production systems as those messages
+ are remotely triggerable.
+
+ Do not select this option.
config MAC80211_VERBOSE_PS_DEBUG
bool "Verbose powersave mode debugging"
- depends on MAC80211_DEBUG
+ depends on MAC80211_DEBUG_MENU
---help---
- Say Y here to print out verbose powersave
- mode debug messages.
+ Selecting this option causes mac80211 to print out very
+ verbose power save mode debugging messages (when mac80211
+ is an AP and has power saving stations.)
+ It should not be selected on production systems as those
+ messages are remotely triggerable.
+
+ Do not select this option.
+
+config MAC80211_VERBOSE_MPL_DEBUG
+ bool "Verbose mesh peer link debugging"
+ depends on MAC80211_DEBUG_MENU
+ depends on MAC80211_MESH
+ ---help---
+ Selecting this option causes mac80211 to print out very
+ verbose mesh peer link debugging messages (when mac80211
+ is taking part in a mesh network).
+ It should not be selected on production systems as those
+ messages are remotely triggerable.
+
+ Do not select this option.
+
+config MAC80211_DEBUG_COUNTERS
+ bool "Extra statistics for TX/RX debugging"
+ depends on MAC80211_DEBUG_MENU
+ depends on MAC80211_DEBUGFS
+ ---help---
+ Selecting this option causes mac80211 to keep additional
+ and very verbose statistics about TX and RX handler use
+ and show them in debugfs.
+
+ If unsure, say N.
+
+config MAC80211_DRIVER_API_TRACER
+ bool "Driver API tracer"
+ depends on MAC80211_DEBUG_MENU
+ depends on EVENT_TRACING
+ help
+ Say Y here to make mac80211 register with the ftrace
+ framework for the driver API -- you can see which
+ driver methods it is calling then by looking at the
+ trace.
+
+ If unsure, say N.