config MAC80211
tristate "Generic IEEE 802.11 Networking Stack (mac80211)"
+ depends on CFG80211
select CRYPTO
select CRYPTO_ECB
select CRYPTO_ARC4
select CRYPTO_AES
select CRC32
- select WIRELESS_EXT
- select CFG80211
---help---
This option enables the hardware independent IEEE 802.11
networking stack.
-menu "Rate control algorithm selection"
- depends on MAC80211 != n
+comment "CFG80211 needs to be enabled for MAC80211"
+ depends on CFG80211=n
+
+if MAC80211 != n
config MAC80211_RC_PID
bool "PID controller based rate control algorithm" if EMBEDDED
- default y
---help---
This option enables a TX rate control algorithm for
mac80211 that uses a PID controller to select the TX
rate.
+config MAC80211_RC_MINSTREL
+ bool "Minstrel" if EMBEDDED
+ default y
+ ---help---
+ This option enables the 'minstrel' TX rate control algorithm
+
choice
prompt "Default rate control algorithm"
- default MAC80211_RC_DEFAULT_PID
+ default MAC80211_RC_DEFAULT_MINSTREL
---help---
This option selects the default rate control algorithm
mac80211 will use. Note that this default can still be
- overriden through the ieee80211_default_rc_algo module
+ overridden through the ieee80211_default_rc_algo module
parameter if different algorithms are available.
config MAC80211_RC_DEFAULT_PID
default rate control algorithm. You should choose
this unless you know what you are doing.
+config MAC80211_RC_DEFAULT_MINSTREL
+ bool "Minstrel"
+ depends on MAC80211_RC_MINSTREL
+ ---help---
+ Select Minstrel as the default rate control algorithm.
+
+
endchoice
config MAC80211_RC_DEFAULT
string
+ default "minstrel" if MAC80211_RC_DEFAULT_MINSTREL
default "pid" if MAC80211_RC_DEFAULT_PID
default ""
-endmenu
+endif
config MAC80211_MESH
bool "Enable mac80211 mesh networking (pre-802.11s) support"
depends on MAC80211 && EXPERIMENTAL
---help---
This options enables support of Draft 802.11s mesh networking.
- The implementation is based on Draft 1.08 of the Mesh Networking
- amendment. For more information visit http://o11s.org/.
-
+ The implementation is based on Draft 2.08 of the Mesh Networking
+ amendment. However, no compliance with that draft is claimed or even
+ possible, as drafts leave a number of identifiers to be defined after
+ ratification. For more information visit http://o11s.org/.
config MAC80211_LEDS
bool "Enable LED triggers"
Do not select this option.
-config MAC80211_LOWTX_FRAME_DUMP
- bool "Debug frame dumping"
- depends on MAC80211_DEBUG_MENU
- ---help---
- Selecting this option will cause the stack to
- print a message for each frame that is handed
- to the lowlevel driver for transmission. This
- message includes all MAC addresses and the
- frame control field.
-
- If unsure, say N and insert the debugging code
- you require into the driver you are debugging.
-
config MAC80211_DEBUG_COUNTERS
bool "Extra statistics for TX/RX debugging"
depends on MAC80211_DEBUG_MENU
If unsure, say N.
-config MAC80211_VERBOSE_SPECT_MGMT_DEBUG
- bool "Verbose Spectrum Management (IEEE 802.11h)debugging"
+config MAC80211_DRIVER_API_TRACER
+ bool "Driver API tracer"
depends on MAC80211_DEBUG_MENU
- ---help---
- Say Y here to print out verbose Spectrum Management (IEEE 802.11h)
- debug messages.
+ depends on EVENT_TRACING
+ help
+ Say Y here to make mac80211 register with the ftrace
+ framework for the driver API -- you can see which
+ driver methods it is calling then by looking at the
+ trace.
+
+ If unsure, say N.