config HAVE_KERNEL_LZMA
bool
+config HAVE_KERNEL_LZO
+ bool
+
choice
prompt "Kernel compression mode"
default KERNEL_GZIP
- depends on HAVE_KERNEL_GZIP || HAVE_KERNEL_BZIP2 || HAVE_KERNEL_LZMA
+ depends on HAVE_KERNEL_GZIP || HAVE_KERNEL_BZIP2 || HAVE_KERNEL_LZMA || HAVE_KERNEL_LZO
help
The linux kernel is a kind of self-extracting executable.
Several compression algorithms are available, which differ
bool "Gzip"
depends on HAVE_KERNEL_GZIP
help
- The old and tried gzip compression. Its compression ratio is
- the poorest among the 3 choices; however its speed (both
- compression and decompression) is the fastest.
+ The old and tried gzip compression. It provides a good balance
+ between compression ratio and decompression speed.
config KERNEL_BZIP2
bool "Bzip2"
two. Compression is slowest. The kernel size is about 33%
smaller with LZMA in comparison to gzip.
+config KERNEL_LZO
+ bool "LZO"
+ depends on HAVE_KERNEL_LZO
+ help
+ Its compression ratio is the poorest among the 4. The kernel
+ size is about about 10% bigger than gzip; however its speed
+ (both compression and decompression) is the fastest.
+
endchoice
config SWAP
is also required. It also scales down nicely to
smaller systems.
+config TINY_RCU
+ bool "UP-only small-memory-footprint RCU"
+ depends on !SMP
+ help
+ This option selects the RCU implementation that is
+ designed for UP systems from which real-time response
+ is not required. This option greatly reduces the
+ memory footprint of RCU.
+
endchoice
config RCU_TRACE
Say N if unsure.
+config RCU_FAST_NO_HZ
+ bool "Accelerate last non-dyntick-idle CPU's grace periods"
+ depends on TREE_RCU && NO_HZ && SMP
+ default n
+ help
+ This option causes RCU to attempt to accelerate grace periods
+ in order to allow the final CPU to enter dynticks-idle state
+ more quickly. On the other hand, this option increases the
+ overhead of the dynticks-idle checking, particularly on systems
+ with large numbers of CPUs.
+
+ Say Y if energy efficiency is critically important, particularly
+ if you have relatively few CPUs.
+
+ Say N if you are unsure.
+
config TREE_RCU_TRACE
def_bool RCU_TRACE && ( TREE_RCU || TREE_PREEMPT_RCU )
select DEBUG_FS
config HAVE_UNSTABLE_SCHED_CLOCK
bool
-config GROUP_SCHED
- bool "Group CPU scheduler"
- depends on EXPERIMENTAL
- default n
- help
- This feature lets CPU scheduler recognize task groups and control CPU
- bandwidth allocation to such task groups.
- In order to create a group from arbitrary set of processes, use
- CONFIG_CGROUPS. (See Control Group support.)
-
-config FAIR_GROUP_SCHED
- bool "Group scheduling for SCHED_OTHER"
- depends on GROUP_SCHED
- default GROUP_SCHED
-
-config RT_GROUP_SCHED
- bool "Group scheduling for SCHED_RR/FIFO"
- depends on EXPERIMENTAL
- depends on GROUP_SCHED
- default n
- help
- This feature lets you explicitly allocate real CPU bandwidth
- to users or control groups (depending on the "Basis for grouping tasks"
- setting below. If enabled, it will also make it impossible to
- schedule realtime tasks for non-root users until you allocate
- realtime bandwidth for them.
- See Documentation/scheduler/sched-rt-group.txt for more information.
-
-choice
- depends on GROUP_SCHED
- prompt "Basis for grouping tasks"
- default USER_SCHED
-
-config USER_SCHED
- bool "user id"
- help
- This option will choose userid as the basis for grouping
- tasks, thus providing equal CPU bandwidth to each user.
-
-config CGROUP_SCHED
- bool "Control groups"
- depends on CGROUPS
- help
- This option allows you to create arbitrary task groups
- using the "cgroup" pseudo filesystem and control
- the cpu bandwidth allocated to each such task group.
- Refer to Documentation/cgroups/cgroups.txt for more
- information on "cgroup" pseudo filesystem.
-
-endchoice
-
menuconfig CGROUPS
boolean "Control Group support"
+ depends on EVENTFD
help
This option adds support for grouping sets of processes together, for
use with process control subsystems such as Cpusets, CFS, memory
Now, memory usage of swap_cgroup is 2 bytes per entry. If swap page
size is 4096bytes, 512k per 1Gbytes of swap.
+menuconfig CGROUP_SCHED
+ bool "Group CPU scheduler"
+ depends on EXPERIMENTAL && CGROUPS
+ default n
+ help
+ This feature lets CPU scheduler recognize task groups and control CPU
+ bandwidth allocation to such task groups. It uses cgroups to group
+ tasks.
+
+if CGROUP_SCHED
+config FAIR_GROUP_SCHED
+ bool "Group scheduling for SCHED_OTHER"
+ depends on CGROUP_SCHED
+ default CGROUP_SCHED
+
+config RT_GROUP_SCHED
+ bool "Group scheduling for SCHED_RR/FIFO"
+ depends on EXPERIMENTAL
+ depends on CGROUP_SCHED
+ default n
+ help
+ This feature lets you explicitly allocate real CPU bandwidth
+ to users or control groups (depending on the "Basis for grouping tasks"
+ setting below. If enabled, it will also make it impossible to
+ schedule realtime tasks for non-root users until you allocate
+ realtime bandwidth for them.
+ See Documentation/scheduler/sched-rt-group.txt for more information.
+
+endif #CGROUP_SCHED
+
endif # CGROUPS
config MM_OWNER
bool
config SYSFS_DEPRECATED_V2
- bool "remove sysfs features which may confuse old userspace tools"
+ bool "enable deprecated sysfs features to support old userspace tools"
depends on SYSFS
default n
select SYSFS_DEPRECATED
config SYSCTL_SYSCALL
bool "Sysctl syscall support" if EMBEDDED
+ depends on PROC_SYSCTL
default y
select SYSCTL
---help---
Say Y if unsure.
-config EVENT_PROFILE
- bool "Tracepoint profiling sources"
- depends on PERF_EVENTS && EVENT_TRACING
- default y
- help
- Allow the use of tracepoints as software performance events.
-
- When this is enabled, you can create perf events based on
- tracepoints using PERF_TYPE_TRACEPOINT and the tracepoint ID
- found in debugfs://tracing/events/*/*/id. (The -e/--events
- option to the perf tool can parse and interpret symbolic
- tracepoints, in the subsystem:tracepoint_name format.)
-
config PERF_COUNTERS
bool "Kernel performance counters (old config option)"
depends on HAVE_PERF_EVENTS
endchoice
+config MMAP_ALLOW_UNINITIALIZED
+ bool "Allow mmapped anonymous memory to be uninitialized"
+ depends on EMBEDDED && !MMU
+ default n
+ help
+ Normally, and according to the Linux spec, anonymous memory obtained
+ from mmap() has it's contents cleared before it is passed to
+ userspace. Enabling this config option allows you to request that
+ mmap() skip that if it is given an MAP_UNINITIALIZED flag, thus
+ providing a huge performance boost. If this option is not enabled,
+ then the flag will be ignored.
+
+ This is taken advantage of by uClibc's malloc(), and also by
+ ELF-FDPIC binfmt's brk and stack allocator.
+
+ Because of the obvious security issues, this option should only be
+ enabled on embedded devices where you control what is run in
+ userspace. Since that isn't generally a problem on no-MMU systems,
+ it is normally safe to say Y here.
+
+ See Documentation/nommu-mmap.txt for more information.
+
config PROFILING
- bool "Profiling support (EXPERIMENTAL)"
+ bool "Profiling support"
help
Say Y here to enable the extended profiling support mechanisms used
by profilers such as OProfile.
See Documentation/slow-work.txt.
+config SLOW_WORK_DEBUG
+ bool "Slow work debugging through debugfs"
+ default n
+ depends on SLOW_WORK && DEBUG_FS
+ help
+ Display the contents of the slow work run queue through debugfs,
+ including items currently executing.
+
+ See Documentation/slow-work.txt.
+
endmenu # General setup
config HAVE_GENERIC_DMA_COHERENT
config PREEMPT_NOTIFIERS
bool
+config PADATA
+ depends on SMP
+ bool
+
+source "kernel/Kconfig.locks"