#include <net/wireless.h>
#include <net/cfg80211.h>
-/* Note! Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
+/**
+ * DOC: Introduction
+ *
+ * mac80211 is the Linux stack for 802.11 hardware that implements
+ * only partial functionality in hard- or firmware. This document
+ * defines the interface between mac80211 and low-level hardware
+ * drivers.
+ */
+
+/**
+ * DOC: Calling mac80211 from interrupts
+ *
+ * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
* called in hardware interrupt context. The low-level driver must not call any
* other functions in hardware interrupt context. If there is a need for such
* call, the low-level driver should first ACK the interrupt and perform the
- * IEEE 802.11 code call after this, e.g., from a scheduled tasklet (in
- * software interrupt context).
+ * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
+ * tasklet function.
+ *
+ * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
+ * use the non-IRQ-safe functions!
*/
-/*
- * Frame format used when passing frame between low-level hardware drivers
- * and IEEE 802.11 driver the same as used in the wireless media, i.e.,
- * buffers start with IEEE 802.11 header and include the same octets that
- * are sent over air.
- *
- * If hardware uses IEEE 802.3 headers (and perform 802.3 <-> 802.11
- * conversion in firmware), upper layer 802.11 code needs to be changed to
- * support this.
- *
- * If the receive frame format is not the same as the real frame sent
- * on the wireless media (e.g., due to padding etc.), upper layer 802.11 code
- * could be updated to provide support for such format assuming this would
- * optimize the performance, e.g., by removing need to re-allocation and
- * copying of the data.
- */
-
-#define IEEE80211_CHAN_W_SCAN 0x00000001
-#define IEEE80211_CHAN_W_ACTIVE_SCAN 0x00000002
-#define IEEE80211_CHAN_W_IBSS 0x00000004
-
-/* Channel information structure. Low-level driver is expected to fill in chan,
- * freq, and val fields. Other fields will be filled in by 80211.o based on
- * hostapd information and low-level driver does not need to use them. The
- * limits for each channel will be provided in 'struct ieee80211_conf' when
- * configuring the low-level driver with hw->config callback. If a device has
- * a default regulatory domain, IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED
- * can be set to let the driver configure all fields */
-struct ieee80211_channel {
- short chan; /* channel number (IEEE 802.11) */
- short freq; /* frequency in MHz */
- int val; /* hw specific value for the channel */
- int flag; /* flag for hostapd use (IEEE80211_CHAN_*) */
- unsigned char power_level;
- unsigned char antenna_max;
-};
-
-#define IEEE80211_RATE_ERP 0x00000001
-#define IEEE80211_RATE_BASIC 0x00000002
-#define IEEE80211_RATE_PREAMBLE2 0x00000004
-#define IEEE80211_RATE_SUPPORTED 0x00000010
-#define IEEE80211_RATE_OFDM 0x00000020
-#define IEEE80211_RATE_CCK 0x00000040
-#define IEEE80211_RATE_MANDATORY 0x00000100
-
-#define IEEE80211_RATE_CCK_2 (IEEE80211_RATE_CCK | IEEE80211_RATE_PREAMBLE2)
-#define IEEE80211_RATE_MODULATION(f) \
- (f & (IEEE80211_RATE_CCK | IEEE80211_RATE_OFDM))
-
-/* Low-level driver should set PREAMBLE2, OFDM and CCK flags.
- * BASIC, SUPPORTED, ERP, and MANDATORY flags are set in 80211.o based on the
- * configuration. */
-struct ieee80211_rate {
- int rate; /* rate in 100 kbps */
- int val; /* hw specific value for the rate */
- int flags; /* IEEE80211_RATE_ flags */
- int val2; /* hw specific value for the rate when using short preamble
- * (only when IEEE80211_RATE_PREAMBLE2 flag is set, i.e., for
- * 2, 5.5, and 11 Mbps) */
- signed char min_rssi_ack;
- unsigned char min_rssi_ack_delta;
-
- /* following fields are set by 80211.o and need not be filled by the
- * low-level driver */
- int rate_inv; /* inverse of the rate (LCM(all rates) / rate) for
- * optimizing channel utilization estimates */
-};
-
-/* 802.11g is backwards-compatible with 802.11b, so a wlan card can
- * actually be both in 11b and 11g modes at the same time. */
-enum ieee80211_phymode {
- MODE_IEEE80211A, /* IEEE 802.11a */
- MODE_IEEE80211B, /* IEEE 802.11b only */
- MODE_IEEE80211G, /* IEEE 802.11g (and 802.11b compatibility) */
-
- /* keep last */
- NUM_IEEE80211_MODES
-};
+/**
+ * DOC: Warning
+ *
+ * If you're reading this document and not the header file itself, it will
+ * be incomplete because not all documentation has been converted yet.
+ */
-struct ieee80211_hw_mode {
- int mode; /* MODE_IEEE80211... */
- int num_channels; /* Number of channels (below) */
- struct ieee80211_channel *channels; /* Array of supported channels */
- int num_rates; /* Number of rates (below) */
- struct ieee80211_rate *rates; /* Array of supported rates */
+/**
+ * DOC: Frame format
+ *
+ * As a general rule, when frames are passed between mac80211 and the driver,
+ * they start with the IEEE 802.11 header and include the same octets that are
+ * sent over the air except for the FCS which should be calculated by the
+ * hardware.
+ *
+ * There are, however, various exceptions to this rule for advanced features:
+ *
+ * The first exception is for hardware encryption and decryption offload
+ * where the IV/ICV may or may not be generated in hardware.
+ *
+ * Secondly, when the hardware handles fragmentation, the frame handed to
+ * the driver from mac80211 is the MSDU, not the MPDU.
+ *
+ * Finally, for received frames, the driver is able to indicate that it has
+ * filled a radiotap header and put that in front of the frame; if it does
+ * not do so then mac80211 may add this under certain circumstances.
+ */
- struct list_head list; /* Internal, don't touch */
+/**
+ * enum ieee80211_notification_type - Low level driver notification
+ * @IEEE80211_NOTIFY_RE_ASSOC: start the re-association sequence
+ */
+enum ieee80211_notification_types {
+ IEEE80211_NOTIFY_RE_ASSOC,
};
-struct ieee80211_tx_queue_params {
- int aifs; /* 0 .. 255; -1 = use default */
- int cw_min; /* 2^n-1: 1, 3, 7, .. , 1023; 0 = use default */
- int cw_max; /* 2^n-1: 1, 3, 7, .. , 1023; 0 = use default */
- int burst_time; /* maximum burst time in 0.1 ms (i.e., 10 = 1 ms);
- * 0 = disabled */
+/**
+ * struct ieee80211_ht_bss_info - describing BSS's HT characteristics
+ *
+ * This structure describes most essential parameters needed
+ * to describe 802.11n HT characteristics in a BSS.
+ *
+ * @primary_channel: channel number of primery channel
+ * @bss_cap: 802.11n's general BSS capabilities (e.g. channel width)
+ * @bss_op_mode: 802.11n's BSS operation modes (e.g. HT protection)
+ */
+struct ieee80211_ht_bss_info {
+ u8 primary_channel;
+ u8 bss_cap; /* use IEEE80211_HT_IE_CHA_ */
+ u8 bss_op_mode; /* use IEEE80211_HT_IE_ */
};
-struct ieee80211_tx_queue_stats_data {
- unsigned int len; /* num packets in queue */
- unsigned int limit; /* queue len (soft) limit */
- unsigned int count; /* total num frames sent */
+/**
+ * enum ieee80211_max_queues - maximum number of queues
+ *
+ * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
+ * @IEEE80211_MAX_AMPDU_QUEUES: Maximum number of queues usable
+ * for A-MPDU operation.
+ */
+enum ieee80211_max_queues {
+ IEEE80211_MAX_QUEUES = 16,
+ IEEE80211_MAX_AMPDU_QUEUES = 16,
};
-enum {
- IEEE80211_TX_QUEUE_DATA0,
- IEEE80211_TX_QUEUE_DATA1,
- IEEE80211_TX_QUEUE_DATA2,
- IEEE80211_TX_QUEUE_DATA3,
- IEEE80211_TX_QUEUE_DATA4,
- IEEE80211_TX_QUEUE_SVP,
-
- NUM_TX_DATA_QUEUES,
-
-/* due to stupidity in the sub-ioctl userspace interface, the items in
- * this struct need to have fixed values. As soon as it is removed, we can
- * fix these entries. */
- IEEE80211_TX_QUEUE_AFTER_BEACON = 6,
- IEEE80211_TX_QUEUE_BEACON = 7
+/**
+ * struct ieee80211_tx_queue_params - transmit queue configuration
+ *
+ * The information provided in this structure is required for QoS
+ * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
+ *
+ * @aifs: arbitration interface space [0..255]
+ * @cw_min: minimum contention window [a value of the form
+ * 2^n-1 in the range 1..32767]
+ * @cw_max: maximum contention window [like @cw_min]
+ * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
+ */
+struct ieee80211_tx_queue_params {
+ u16 txop;
+ u16 cw_min;
+ u16 cw_max;
+ u8 aifs;
};
+/**
+ * struct ieee80211_tx_queue_stats - transmit queue statistics
+ *
+ * @len: number of packets in queue
+ * @limit: queue length limit
+ * @count: number of frames sent
+ */
struct ieee80211_tx_queue_stats {
- struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES];
+ unsigned int len;
+ unsigned int limit;
+ unsigned int count;
};
struct ieee80211_low_level_stats {
unsigned int dot11RTSSuccessCount;
};
-/* Transmit control fields. This data structure is passed to low-level driver
- * with each TX frame. The low-level driver is responsible for configuring
- * the hardware to use given values (depending on what is supported). */
-#define HW_KEY_IDX_INVALID -1
-
-struct ieee80211_tx_control {
- int tx_rate; /* Transmit rate, given as the hw specific value for the
- * rate (from struct ieee80211_rate) */
- int rts_cts_rate; /* Transmit rate for RTS/CTS frame, given as the hw
- * specific value for the rate (from
- * struct ieee80211_rate) */
-
-#define IEEE80211_TXCTL_REQ_TX_STATUS (1<<0)/* request TX status callback for
- * this frame */
-#define IEEE80211_TXCTL_DO_NOT_ENCRYPT (1<<1) /* send this frame without
- * encryption; e.g., for EAPOL
- * frames */
-#define IEEE80211_TXCTL_USE_RTS_CTS (1<<2) /* use RTS-CTS before sending
- * frame */
-#define IEEE80211_TXCTL_USE_CTS_PROTECT (1<<3) /* use CTS protection for the
- * frame (e.g., for combined
- * 802.11g / 802.11b networks) */
-#define IEEE80211_TXCTL_NO_ACK (1<<4) /* tell the low level not to
- * wait for an ack */
-#define IEEE80211_TXCTL_RATE_CTRL_PROBE (1<<5)
-#define IEEE80211_TXCTL_CLEAR_DST_MASK (1<<6)
-#define IEEE80211_TXCTL_REQUEUE (1<<7)
-#define IEEE80211_TXCTL_FIRST_FRAGMENT (1<<8) /* this is a first fragment of
- * the frame */
-#define IEEE80211_TXCTL_TKIP_NEW_PHASE1_KEY (1<<9)
-#define IEEE80211_TXCTL_LONG_RETRY_LIMIT (1<<10) /* this frame should be send
- * using the through
- * set_retry_limit configured
- * long retry value */
- u32 flags; /* tx control flags defined
- * above */
- u8 retry_limit; /* 1 = only first attempt, 2 = one retry, ..
- * This could be used when set_retry_limit
- * is not implemented by the driver */
- u8 power_level; /* per-packet transmit power level, in dBm */
- u8 antenna_sel_tx; /* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */
- s8 key_idx; /* HW_KEY_IDX_INVALID = do not encrypt,
- * other values: keyidx from hw->set_key() */
- u8 icv_len; /* length of the ICV/MIC field in octets */
- u8 iv_len; /* length of the IV field in octets */
- u8 tkip_key[16]; /* generated phase2/phase1 key for hw TKIP */
- u8 queue; /* hardware queue to use for this frame;
- * 0 = highest, hw->queues-1 = lowest */
- u8 sw_retry_attempt; /* number of times hw has tried to
- * transmit frame (not incl. hw retries) */
-
- struct ieee80211_rate *rate; /* internal 80211.o rate */
- struct ieee80211_rate *rts_rate; /* internal 80211.o rate
- * for RTS/CTS */
- int alt_retry_rate; /* retry rate for the last retries, given as the
- * hw specific value for the rate (from
- * struct ieee80211_rate). To be used to limit
- * packet dropping when probing higher rates, if hw
- * supports multiple retry rates. -1 = not used */
- int type; /* internal */
- int ifindex; /* internal */
+/**
+ * enum ieee80211_bss_change - BSS change notification flags
+ *
+ * These flags are used with the bss_info_changed() callback
+ * to indicate which BSS parameter changed.
+ *
+ * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
+ * also implies a change in the AID.
+ * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
+ * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
+ * @BSS_CHANGED_HT: 802.11n parameters changed
+ */
+enum ieee80211_bss_change {
+ BSS_CHANGED_ASSOC = 1<<0,
+ BSS_CHANGED_ERP_CTS_PROT = 1<<1,
+ BSS_CHANGED_ERP_PREAMBLE = 1<<2,
+ BSS_CHANGED_HT = 1<<4,
+};
+
+/**
+ * struct ieee80211_bss_conf - holds the BSS's changing parameters
+ *
+ * This structure keeps information about a BSS (and an association
+ * to that BSS) that can change during the lifetime of the BSS.
+ *
+ * @assoc: association status
+ * @aid: association ID number, valid only when @assoc is true
+ * @use_cts_prot: use CTS protection
+ * @use_short_preamble: use 802.11b short preamble
+ * @dtim_period: num of beacons before the next DTIM, for PSM
+ * @timestamp: beacon timestamp
+ * @beacon_int: beacon interval
+ * @assoc_capability: capabilities taken from assoc resp
+ * @assoc_ht: association in HT mode
+ * @ht_conf: ht capabilities
+ * @ht_bss_conf: ht extended capabilities
+ */
+struct ieee80211_bss_conf {
+ /* association related data */
+ bool assoc;
+ u16 aid;
+ /* erp related data */
+ bool use_cts_prot;
+ bool use_short_preamble;
+ u8 dtim_period;
+ u16 beacon_int;
+ u16 assoc_capability;
+ u64 timestamp;
+ /* ht related data */
+ bool assoc_ht;
+ struct ieee80211_ht_info *ht_conf;
+ struct ieee80211_ht_bss_info *ht_bss_conf;
+};
+
+/**
+ * enum mac80211_tx_control_flags - flags to describe transmission information/status
+ *
+ * These flags are used with the @flags member of &ieee80211_tx_info.
+ *
+ * @IEEE80211_TX_CTL_REQ_TX_STATUS: request TX status callback for this frame.
+ * @IEEE80211_TX_CTL_USE_RTS_CTS: use RTS-CTS before sending frame
+ * @IEEE80211_TX_CTL_USE_CTS_PROTECT: use CTS protection for the frame (e.g.,
+ * for combined 802.11g / 802.11b networks)
+ * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
+ * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: TBD
+ * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
+ * station
+ * @IEEE80211_TX_CTL_REQUEUE: TBD
+ * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
+ * @IEEE80211_TX_CTL_SHORT_PREAMBLE: TBD
+ * @IEEE80211_TX_CTL_LONG_RETRY_LIMIT: this frame should be send using the
+ * through set_retry_limit configured long retry value
+ * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
+ * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
+ * @IEEE80211_TX_CTL_OFDM_HT: this frame can be sent in HT OFDM rates. number
+ * of streams when this flag is on can be extracted from antenna_sel_tx,
+ * so if 1 antenna is marked use SISO, 2 antennas marked use MIMO, n
+ * antennas marked use MIMO_n.
+ * @IEEE80211_TX_CTL_GREEN_FIELD: use green field protection for this frame
+ * @IEEE80211_TX_CTL_40_MHZ_WIDTH: send this frame using 40 Mhz channel width
+ * @IEEE80211_TX_CTL_DUP_DATA: duplicate data frame on both 20 Mhz channels
+ * @IEEE80211_TX_CTL_SHORT_GI: send this frame using short guard interval
+ * @IEEE80211_TX_CTL_INJECTED: TBD
+ * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
+ * because the destination STA was in powersave mode.
+ * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
+ * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
+ * is for the whole aggregation.
+ * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
+ * so consider using block ack request (BAR).
+ * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
+ * number to this frame, taking care of not overwriting the fragment
+ * number and increasing the sequence number only when the
+ * IEEE80211_TX_CTL_FIRST_FRAGMENT flags is set. mac80211 will properly
+ * assign sequence numbers to QoS-data frames but cannot do so correctly
+ * for non-QoS-data and management frames because beacons need them from
+ * that counter as well and mac80211 cannot guarantee proper sequencing.
+ * If this flag is set, the driver should instruct the hardware to
+ * assign a sequence number to the frame or assign one itself. Cf. IEEE
+ * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
+ * beacons always be clear for frames without a sequence number field.
+ */
+enum mac80211_tx_control_flags {
+ IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
+ IEEE80211_TX_CTL_USE_RTS_CTS = BIT(2),
+ IEEE80211_TX_CTL_USE_CTS_PROTECT = BIT(3),
+ IEEE80211_TX_CTL_NO_ACK = BIT(4),
+ IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(5),
+ IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(6),
+ IEEE80211_TX_CTL_REQUEUE = BIT(7),
+ IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(8),
+ IEEE80211_TX_CTL_SHORT_PREAMBLE = BIT(9),
+ IEEE80211_TX_CTL_LONG_RETRY_LIMIT = BIT(10),
+ IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(12),
+ IEEE80211_TX_CTL_AMPDU = BIT(13),
+ IEEE80211_TX_CTL_OFDM_HT = BIT(14),
+ IEEE80211_TX_CTL_GREEN_FIELD = BIT(15),
+ IEEE80211_TX_CTL_40_MHZ_WIDTH = BIT(16),
+ IEEE80211_TX_CTL_DUP_DATA = BIT(17),
+ IEEE80211_TX_CTL_SHORT_GI = BIT(18),
+ IEEE80211_TX_CTL_INJECTED = BIT(19),
+ IEEE80211_TX_STAT_TX_FILTERED = BIT(20),
+ IEEE80211_TX_STAT_ACK = BIT(21),
+ IEEE80211_TX_STAT_AMPDU = BIT(22),
+ IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(23),
+ IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(24),
+};
+
+
+#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE \
+ (sizeof(((struct sk_buff *)0)->cb) - 8)
+#define IEEE80211_TX_INFO_DRIVER_DATA_PTRS \
+ (IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *))
+
+/**
+ * struct ieee80211_tx_info - skb transmit information
+ *
+ * This structure is placed in skb->cb for three uses:
+ * (1) mac80211 TX control - mac80211 tells the driver what to do
+ * (2) driver internal use (if applicable)
+ * (3) TX status information - driver tells mac80211 what happened
+ *
+ * @flags: transmit info flags, defined above
+ * @band: TBD
+ * @tx_rate_idx: TBD
+ * @antenna_sel_tx: TBD
+ * @control: union for control data
+ * @status: union for status data
+ * @driver_data: array of driver_data pointers
+ * @retry_count: number of retries
+ * @excessive_retries: set to 1 if the frame was retried many times
+ * but not acknowledged
+ * @ampdu_ack_len: number of aggregated frames.
+ * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
+ * @ampdu_ack_map: block ack bit map for the aggregation.
+ * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
+ * @ack_signal: signal strength of the ACK frame
+ */
+struct ieee80211_tx_info {
+ /* common information */
+ u32 flags;
+ u8 band;
+ s8 tx_rate_idx;
+ u8 antenna_sel_tx;
+
+ /* 1 byte hole */
+
+ union {
+ struct {
+ struct ieee80211_vif *vif;
+ struct ieee80211_key_conf *hw_key;
+ unsigned long jiffies;
+ u16 aid;
+ s8 rts_cts_rate_idx, alt_retry_rate_idx;
+ u8 retry_limit;
+ u8 icv_len;
+ u8 iv_len;
+ } control;
+ struct {
+ u64 ampdu_ack_map;
+ int ack_signal;
+ u8 retry_count;
+ bool excessive_retries;
+ u8 ampdu_ack_len;
+ } status;
+ void *driver_data[IEEE80211_TX_INFO_DRIVER_DATA_PTRS];
+ };
};
-/* Receive status. The low-level driver should provide this information
- * (the subset supported by hardware) to the 802.11 code with each received
- * frame. */
+static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
+{
+ return (struct ieee80211_tx_info *)skb->cb;
+}
+
+
+/**
+ * enum mac80211_rx_flags - receive flags
+ *
+ * These flags are used with the @flag member of &struct ieee80211_rx_status.
+ * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
+ * Use together with %RX_FLAG_MMIC_STRIPPED.
+ * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
+ * @RX_FLAG_RADIOTAP: This frame starts with a radiotap header.
+ * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
+ * verification has been done by the hardware.
+ * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
+ * If this flag is set, the stack cannot do any replay detection
+ * hence the driver or hardware will have to do that.
+ * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
+ * the frame.
+ * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
+ * the frame.
+ * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
+ * is valid. This is useful in monitor mode and necessary for beacon frames
+ * to enable IBSS merging.
+ */
+enum mac80211_rx_flags {
+ RX_FLAG_MMIC_ERROR = 1<<0,
+ RX_FLAG_DECRYPTED = 1<<1,
+ RX_FLAG_RADIOTAP = 1<<2,
+ RX_FLAG_MMIC_STRIPPED = 1<<3,
+ RX_FLAG_IV_STRIPPED = 1<<4,
+ RX_FLAG_FAILED_FCS_CRC = 1<<5,
+ RX_FLAG_FAILED_PLCP_CRC = 1<<6,
+ RX_FLAG_TSFT = 1<<7,
+};
+
+/**
+ * struct ieee80211_rx_status - receive status
+ *
+ * The low-level driver should provide this information (the subset
+ * supported by hardware) to the 802.11 code with each received
+ * frame.
+ *
+ * @mactime: value in microseconds of the 64-bit Time Synchronization Function
+ * (TSF) timer when the first data symbol (MPDU) arrived at the hardware.
+ * @band: the active band when this frame was received
+ * @freq: frequency the radio was tuned to when receiving this frame, in MHz
+ * @signal: signal strength when receiving this frame, either in dBm, in dB or
+ * unspecified depending on the hardware capabilities flags
+ * @IEEE80211_HW_SIGNAL_*
+ * @noise: noise when receiving this frame, in dBm.
+ * @qual: overall signal quality indication, in percent (0-100).
+ * @antenna: antenna used
+ * @rate_idx: index of data rate into band's supported rates
+ * @flag: %RX_FLAG_*
+ */
struct ieee80211_rx_status {
u64 mactime;
- int freq; /* receive frequency in Mhz */
- int channel;
- int phymode;
- int ssi;
- int signal; /* used as qual in statistics reporting */
+ enum ieee80211_band band;
+ int freq;
+ int signal;
int noise;
+ int qual;
int antenna;
- int rate;
-#define RX_FLAG_MMIC_ERROR (1<<0)
-#define RX_FLAG_DECRYPTED (1<<1)
-#define RX_FLAG_RADIOTAP (1<<2)
+ int rate_idx;
int flag;
};
-/* Transmit status. The low-level driver should provide this information
- * (the subset supported by hardware) to the 802.11 code for each transmit
- * frame. */
-struct ieee80211_tx_status {
- /* copied ieee80211_tx_control structure */
- struct ieee80211_tx_control control;
-
-#define IEEE80211_TX_STATUS_TX_FILTERED (1<<0)
-#define IEEE80211_TX_STATUS_ACK (1<<1) /* whether the TX frame was ACKed */
- u32 flags; /* tx staus flags defined above */
-
- int ack_signal; /* measured signal strength of the ACK frame */
- int excessive_retries;
- int retry_count;
-
- int queue_length; /* information about TX queue */
- int queue_number;
+/**
+ * enum ieee80211_conf_flags - configuration flags
+ *
+ * Flags to define PHY configuration options
+ *
+ * @IEEE80211_CONF_SHORT_SLOT_TIME: use 802.11g short slot time
+ * @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
+ * @IEEE80211_CONF_SUPPORT_HT_MODE: use 802.11n HT capabilities (if supported)
+ * @IEEE80211_CONF_PS: Enable 802.11 power save mode
+ */
+enum ieee80211_conf_flags {
+ IEEE80211_CONF_SHORT_SLOT_TIME = (1<<0),
+ IEEE80211_CONF_RADIOTAP = (1<<1),
+ IEEE80211_CONF_SUPPORT_HT_MODE = (1<<2),
+ IEEE80211_CONF_PS = (1<<3),
};
-
/**
* struct ieee80211_conf - configuration of the device
*
* This struct indicates how the driver shall configure the hardware.
*
* @radio_enabled: when zero, driver is required to switch off the radio.
+ * TODO make a flag
+ * @beacon_int: beacon interval (TODO make interface config)
+ * @listen_interval: listen interval in units of beacon interval
+ * @flags: configuration flags defined above
+ * @power_level: requested transmit power (in dBm)
+ * @max_antenna_gain: maximum antenna gain (in dBi)
+ * @antenna_sel_tx: transmit antenna selection, 0: default/diversity,
+ * 1/2: antenna 0/1
+ * @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx
+ * @ht_conf: describes current self configuration of 802.11n HT capabilies
+ * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters
+ * @channel: the channel to tune to
*/
struct ieee80211_conf {
- int channel; /* IEEE 802.11 channel number */
- int freq; /* MHz */
- int channel_val; /* hw specific value for the channel */
-
- int phymode; /* MODE_IEEE80211A, .. */
- struct ieee80211_channel *chan;
- struct ieee80211_hw_mode *mode;
- unsigned int regulatory_domain;
int radio_enabled;
int beacon_int;
-
-#define IEEE80211_CONF_SHORT_SLOT_TIME (1<<0) /* use IEEE 802.11g Short Slot
- * Time */
-#define IEEE80211_CONF_SSID_HIDDEN (1<<1) /* do not broadcast the ssid */
-#define IEEE80211_CONF_RADIOTAP (1<<2) /* use radiotap if supported
- check this bit at RX time */
- u32 flags; /* configuration flags defined above */
-
- u8 power_level; /* transmit power limit for current
- * regulatory domain; in dBm */
- u8 antenna_max; /* maximum antenna gain */
-
- /* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */
+ u16 listen_interval;
+ u32 flags;
+ int power_level;
+ int max_antenna_gain;
u8 antenna_sel_tx;
u8 antenna_sel_rx;
+
+ struct ieee80211_channel *channel;
+
+ struct ieee80211_ht_info ht_conf;
+ struct ieee80211_ht_bss_info ht_bss_conf;
};
/**
* enum ieee80211_if_types - types of 802.11 network interfaces
*
+ * @IEEE80211_IF_TYPE_INVALID: invalid interface type, not used
+ * by mac80211 itself
* @IEEE80211_IF_TYPE_AP: interface in AP mode.
* @IEEE80211_IF_TYPE_MGMT: special interface for communication with hostap
* daemon. Drivers should never see this type.
* @IEEE80211_IF_TYPE_IBSS: interface in IBSS (ad-hoc) mode.
* @IEEE80211_IF_TYPE_MNTR: interface in monitor (rfmon) mode.
* @IEEE80211_IF_TYPE_WDS: interface in WDS mode.
- * @IEEE80211_IF_TYPE_VLAN: not used.
+ * @IEEE80211_IF_TYPE_VLAN: VLAN interface bound to an AP, drivers
+ * will never see this type.
+ * @IEEE80211_IF_TYPE_MESH_POINT: 802.11s mesh point
*/
enum ieee80211_if_types {
- IEEE80211_IF_TYPE_AP = 0x00000000,
- IEEE80211_IF_TYPE_MGMT = 0x00000001,
- IEEE80211_IF_TYPE_STA = 0x00000002,
- IEEE80211_IF_TYPE_IBSS = 0x00000003,
- IEEE80211_IF_TYPE_MNTR = 0x00000004,
- IEEE80211_IF_TYPE_WDS = 0x5A580211,
- IEEE80211_IF_TYPE_VLAN = 0x00080211,
+ IEEE80211_IF_TYPE_INVALID,
+ IEEE80211_IF_TYPE_AP,
+ IEEE80211_IF_TYPE_STA,
+ IEEE80211_IF_TYPE_IBSS,
+ IEEE80211_IF_TYPE_MESH_POINT,
+ IEEE80211_IF_TYPE_MNTR,
+ IEEE80211_IF_TYPE_WDS,
+ IEEE80211_IF_TYPE_VLAN,
};
/**
+ * struct ieee80211_vif - per-interface data
+ *
+ * Data in this structure is continually present for driver
+ * use during the life of a virtual interface.
+ *
+ * @type: type of this virtual interface
+ * @drv_priv: data area for driver use, will always be aligned to
+ * sizeof(void *).
+ */
+struct ieee80211_vif {
+ enum ieee80211_if_types type;
+ /* must be last */
+ u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
+};
+
+static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
+{
+#ifdef CONFIG_MAC80211_MESH
+ return vif->type == IEEE80211_IF_TYPE_MESH_POINT;
+#endif
+ return false;
+}
+
+/**
* struct ieee80211_if_init_conf - initial configuration of an interface
*
- * @if_id: internal interface ID. This number has no particular meaning to
- * drivers and the only allowed usage is to pass it to
- * ieee80211_beacon_get() and ieee80211_get_buffered_bc() functions.
- * This field is not valid for monitor interfaces
- * (interfaces of %IEEE80211_IF_TYPE_MNTR type).
+ * @vif: pointer to a driver-use per-interface structure. The pointer
+ * itself is also used for various functions including
+ * ieee80211_beacon_get() and ieee80211_get_buffered_bc().
* @type: one of &enum ieee80211_if_types constants. Determines the type of
* added/removed interface.
* @mac_addr: pointer to MAC address of the interface. This pointer is valid
* until the interface is removed (i.e. it cannot be used after
* remove_interface() callback was called for this interface).
- * This pointer will be %NULL for monitor interfaces, be careful.
*
* This structure is used in add_interface() and remove_interface()
* callbacks of &struct ieee80211_hw.
* in pure monitor mode.
*/
struct ieee80211_if_init_conf {
- int if_id;
- int type;
+ enum ieee80211_if_types type;
+ struct ieee80211_vif *vif;
void *mac_addr;
};
/**
+ * enum ieee80211_if_conf_change - interface config change flags
+ *
+ * @IEEE80211_IFCC_BSSID: The BSSID changed.
+ * @IEEE80211_IFCC_SSID: The SSID changed.
+ * @IEEE80211_IFCC_BEACON: The beacon for this interface changed
+ * (currently AP and MESH only), use ieee80211_beacon_get().
+ */
+enum ieee80211_if_conf_change {
+ IEEE80211_IFCC_BSSID = BIT(0),
+ IEEE80211_IFCC_SSID = BIT(1),
+ IEEE80211_IFCC_BEACON = BIT(2),
+};
+
+/**
* struct ieee80211_if_conf - configuration of an interface
*
- * @type: type of the interface. This is always the same as was specified in
- * &struct ieee80211_if_init_conf. The type of an interface never changes
- * during the life of the interface; this field is present only for
- * convenience.
+ * @changed: parameters that have changed, see &enum ieee80211_if_conf_change.
* @bssid: BSSID of the network we are associated to/creating.
* @ssid: used (together with @ssid_len) by drivers for hardware that
* generate beacons independently. The pointer is valid only during the
* config_interface() call, so copy the value somewhere if you need
* it.
* @ssid_len: length of the @ssid field.
- * @generic_elem: used (together with @generic_elem_len) by drivers for
- * hardware that generate beacons independently. The pointer is valid
- * only during the config_interface() call, so copy the value somewhere
- * if you need it.
- * @generic_elem_len: length of the generic element.
- * @beacon: beacon template. Valid only if @host_gen_beacon_template in
- * &struct ieee80211_hw is set. The driver is responsible of freeing
- * the sk_buff.
- * @beacon_control: tx_control for the beacon template, this field is only
- * valid when the @beacon field was set.
*
* This structure is passed to the config_interface() callback of
* &struct ieee80211_hw.
*/
struct ieee80211_if_conf {
- int type;
+ u32 changed;
u8 *bssid;
u8 *ssid;
size_t ssid_len;
- u8 *generic_elem;
- size_t generic_elem_len;
- struct sk_buff *beacon;
- struct ieee80211_tx_control *beacon_control;
};
-typedef enum {
- ALG_NONE,
+/**
+ * enum ieee80211_key_alg - key algorithm
+ * @ALG_WEP: WEP40 or WEP104
+ * @ALG_TKIP: TKIP
+ * @ALG_CCMP: CCMP (AES)
+ */
+enum ieee80211_key_alg {
ALG_WEP,
ALG_TKIP,
ALG_CCMP,
-} ieee80211_key_alg;
+};
-/*
- * This flag indiciates that the station this key is being
- * configured for may use QoS. If your hardware cannot handle
- * that situation it should reject that key.
+/**
+ * enum ieee80211_key_len - key length
+ * @LEN_WEP40: WEP 5-byte long key
+ * @LEN_WEP104: WEP 13-byte long key
*/
-#define IEEE80211_KEY_FLAG_WMM_STA (1<<0)
-
-struct ieee80211_key_conf {
- /*
- * To be set by the driver to the key index it would like to
- * get in the ieee80211_tx_control.key_idx which defaults
- * to HW_KEY_IDX_INVALID so that shouldn't be used.
- */
- int hw_key_idx;
+enum ieee80211_key_len {
+ LEN_WEP40 = 5,
+ LEN_WEP104 = 13,
+};
- /* key algorithm, ALG_NONE should never be seen by the driver */
- ieee80211_key_alg alg;
+/**
+ * enum ieee80211_key_flags - key flags
+ *
+ * These flags are used for communication about keys between the driver
+ * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
+ *
+ * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates
+ * that the STA this key will be used with could be using QoS.
+ * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
+ * driver to indicate that it requires IV generation for this
+ * particular key.
+ * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
+ * the driver for a TKIP key if it requires Michael MIC
+ * generation in software.
+ * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
+ * that the key is pairwise rather then a shared key.
+ */
+enum ieee80211_key_flags {
+ IEEE80211_KEY_FLAG_WMM_STA = 1<<0,
+ IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1,
+ IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
+ IEEE80211_KEY_FLAG_PAIRWISE = 1<<3,
+};
- /* key flags, see above */
+/**
+ * struct ieee80211_key_conf - key information
+ *
+ * This key information is given by mac80211 to the driver by
+ * the set_key() callback in &struct ieee80211_ops.
+ *
+ * @hw_key_idx: To be set by the driver, this is the key index the driver
+ * wants to be given when a frame is transmitted and needs to be
+ * encrypted in hardware.
+ * @alg: The key algorithm.
+ * @flags: key flags, see &enum ieee80211_key_flags.
+ * @keyidx: the key index (0-3)
+ * @keylen: key material length
+ * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
+ * data block:
+ * - Temporal Encryption Key (128 bits)
+ * - Temporal Authenticator Tx MIC Key (64 bits)
+ * - Temporal Authenticator Rx MIC Key (64 bits)
+ *
+ */
+struct ieee80211_key_conf {
+ enum ieee80211_key_alg alg;
+ u8 hw_key_idx;
u8 flags;
-
- /* key index: 0-3 */
s8 keyidx;
-
- /* length of key material */
u8 keylen;
-
- /* the key material */
u8 key[0];
};
-#define IEEE80211_SEQ_COUNTER_RX 0
-#define IEEE80211_SEQ_COUNTER_TX 1
-
-typedef enum {
+/**
+ * enum set_key_cmd - key command
+ *
+ * Used with the set_key() callback in &struct ieee80211_ops, this
+ * indicates whether a key is being removed or added.
+ *
+ * @SET_KEY: a key is set
+ * @DISABLE_KEY: a key must be disabled
+ */
+enum set_key_cmd {
SET_KEY, DISABLE_KEY,
-} set_key_cmd;
+};
-/* This is driver-visible part of the per-hw state the stack keeps. */
-struct ieee80211_hw {
- /* points to the cfg80211 wiphy for this piece. Note
- * that you must fill in the perm_addr and dev fields
- * of this structure, use the macros provided below. */
- struct wiphy *wiphy;
+/**
+ * enum sta_notify_cmd - sta notify command
+ *
+ * Used with the sta_notify() callback in &struct ieee80211_ops, this
+ * indicates addition and removal of a station to station table.
+ *
+ * @STA_NOTIFY_ADD: a station was added to the station table
+ * @STA_NOTIFY_REMOVE: a station being removed from the station table
+ */
+enum sta_notify_cmd {
+ STA_NOTIFY_ADD, STA_NOTIFY_REMOVE
+};
- /* assigned by mac80211, don't write */
- struct ieee80211_conf conf;
+/**
+ * enum ieee80211_tkip_key_type - get tkip key
+ *
+ * Used by drivers which need to get a tkip key for skb. Some drivers need a
+ * phase 1 key, others need a phase 2 key. A single function allows the driver
+ * to get the key, this enum indicates what type of key is required.
+ *
+ * @IEEE80211_TKIP_P1_KEY: the driver needs a phase 1 key
+ * @IEEE80211_TKIP_P2_KEY: the driver needs a phase 2 key
+ */
+enum ieee80211_tkip_key_type {
+ IEEE80211_TKIP_P1_KEY,
+ IEEE80211_TKIP_P2_KEY,
+};
- /* Single thread workqueue available for driver use
- * Allocated by mac80211 on registration */
- struct workqueue_struct *workqueue;
+/**
+ * enum ieee80211_hw_flags - hardware flags
+ *
+ * These flags are used to indicate hardware capabilities to
+ * the stack. Generally, flags here should have their meaning
+ * done in a way that the simplest hardware doesn't need setting
+ * any particular flags. There are some exceptions to this rule,
+ * however, so you are advised to review these flags carefully.
+ *
+ * @IEEE80211_HW_RX_INCLUDES_FCS:
+ * Indicates that received frames passed to the stack include
+ * the FCS at the end.
+ *
+ * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
+ * Some wireless LAN chipsets buffer broadcast/multicast frames
+ * for power saving stations in the hardware/firmware and others
+ * rely on the host system for such buffering. This option is used
+ * to configure the IEEE 802.11 upper layer to buffer broadcast and
+ * multicast frames when there are power saving stations so that
+ * the driver can fetch them with ieee80211_get_buffered_bc().
+ *
+ * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
+ * Hardware is not capable of short slot operation on the 2.4 GHz band.
+ *
+ * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
+ * Hardware is not capable of receiving frames with short preamble on
+ * the 2.4 GHz band.
+ *
+ * @IEEE80211_HW_SIGNAL_UNSPEC:
+ * Hardware can provide signal values but we don't know its units. We
+ * expect values between 0 and @max_signal.
+ * If possible please provide dB or dBm instead.
+ *
+ * @IEEE80211_HW_SIGNAL_DB:
+ * Hardware gives signal values in dB, decibel difference from an
+ * arbitrary, fixed reference. We expect values between 0 and @max_signal.
+ * If possible please provide dBm instead.
+ *
+ * @IEEE80211_HW_SIGNAL_DBM:
+ * Hardware gives signal values in dBm, decibel difference from
+ * one milliwatt. This is the preferred method since it is standardized
+ * between different devices. @max_signal does not need to be set.
+ *
+ * @IEEE80211_HW_NOISE_DBM:
+ * Hardware can provide noise (radio interference) values in units dBm,
+ * decibel difference from one milliwatt.
+ *
+ * @IEEE80211_HW_SPECTRUM_MGMT:
+ * Hardware supports spectrum management defined in 802.11h
+ * Measurement, Channel Switch, Quieting, TPC
+ */
+enum ieee80211_hw_flags {
+ IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
+ IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
+ IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
+ IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
+ IEEE80211_HW_SIGNAL_UNSPEC = 1<<5,
+ IEEE80211_HW_SIGNAL_DB = 1<<6,
+ IEEE80211_HW_SIGNAL_DBM = 1<<7,
+ IEEE80211_HW_NOISE_DBM = 1<<8,
+ IEEE80211_HW_SPECTRUM_MGMT = 1<<9,
+};
- /* Pointer to the private area that was
- * allocated with this struct for you. */
+/**
+ * struct ieee80211_hw - hardware information and state
+ *
+ * This structure contains the configuration and hardware
+ * information for an 802.11 PHY.
+ *
+ * @wiphy: This points to the &struct wiphy allocated for this
+ * 802.11 PHY. You must fill in the @perm_addr and @dev
+ * members of this structure using SET_IEEE80211_DEV()
+ * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
+ * bands (with channels, bitrates) are registered here.
+ *
+ * @conf: &struct ieee80211_conf, device configuration, don't use.
+ *
+ * @workqueue: single threaded workqueue available for driver use,
+ * allocated by mac80211 on registration and flushed when an
+ * interface is removed.
+ * NOTICE: All work performed on this workqueue should NEVER
+ * acquire the RTNL lock (i.e. Don't use the function
+ * ieee80211_iterate_active_interfaces())
+ *
+ * @priv: pointer to private area that was allocated for driver use
+ * along with this structure.
+ *
+ * @flags: hardware flags, see &enum ieee80211_hw_flags.
+ *
+ * @extra_tx_headroom: headroom to reserve in each transmit skb
+ * for use by the driver (e.g. for transmit headers.)
+ *
+ * @channel_change_time: time (in microseconds) it takes to change channels.
+ *
+ * @max_signal: Maximum value for signal (rssi) in RX information, used
+ * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
+ *
+ * @max_listen_interval: max listen interval in units of beacon interval
+ * that HW supports
+ *
+ * @queues: number of available hardware transmit queues for
+ * data packets. WMM/QoS requires at least four, these
+ * queues need to have configurable access parameters.
+ *
+ * @ampdu_queues: number of available hardware transmit queues
+ * for A-MPDU packets, these have no access parameters
+ * because they're used only for A-MPDU frames. Note that
+ * mac80211 will not currently use any of the regular queues
+ * for aggregation.
+ *
+ * @rate_control_algorithm: rate control algorithm for this hardware.
+ * If unset (NULL), the default algorithm will be used. Must be
+ * set before calling ieee80211_register_hw().
+ *
+ * @vif_data_size: size (in bytes) of the drv_priv data area
+ * within &struct ieee80211_vif.
+ */
+struct ieee80211_hw {
+ struct ieee80211_conf conf;
+ struct wiphy *wiphy;
+ struct workqueue_struct *workqueue;
+ const char *rate_control_algorithm;
void *priv;
-
- /* The rest is information about your hardware */
-
- /* TODO: frame_type 802.11/802.3, sw_encryption requirements */
-
-/* hole at 0 */
-
- /*
- * The device only needs to be supplied with a beacon template.
- * If you need the host to generate each beacon then don't use
- * this flag and use ieee80211_beacon_get().
- */
-#define IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE (1<<1)
-
- /*
- * Some devices handle decryption internally and do not
- * indicate whether the frame was encrypted (unencrypted frames
- * will be dropped by the hardware, unless specifically allowed
- * through.)
- * It is permissible to not handle all encrypted frames and fall
- * back to software encryption; however, if this flag is set
- * unencrypted frames must be dropped unless the driver is told
- * otherwise via the set_ieee8021x() callback.
- */
-#define IEEE80211_HW_DEVICE_HIDES_WEP (1<<2)
-
- /* Whether RX frames passed to ieee80211_rx() include FCS in the end */
-#define IEEE80211_HW_RX_INCLUDES_FCS (1<<3)
-
- /* Some wireless LAN chipsets buffer broadcast/multicast frames for
- * power saving stations in the hardware/firmware and others rely on
- * the host system for such buffering. This option is used to
- * configure the IEEE 802.11 upper layer to buffer broadcast/multicast
- * frames when there are power saving stations so that low-level driver
- * can fetch them with ieee80211_get_buffered_bc(). */
-#define IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING (1<<4)
-
- /*
- * This flag is only relevant if hardware encryption is used.
- * If set, it has two meanings:
- * 1) the IV and ICV are present in received frames that have
- * been decrypted (unless IEEE80211_HW_DEVICE_HIDES_WEP is
- * also set)
- * 2) on transmission, the IV should be generated in software.
- *
- * Please let us know if you *don't* use this flag, the stack would
- * really like to be able to get the IV to keep key statistics
- * accurate.
- */
-#define IEEE80211_HW_WEP_INCLUDE_IV (1<<5)
-
-/* hole at 6 */
-
-/* hole at 7 */
-
- /*
- * Some devices handle Michael MIC internally and do not include MIC in
- * the received packets passed up. This flag must be set for such
- * devices. The 'encryption' frame control bit is expected to be still
- * set in the IEEE 802.11 header with this option unlike with the
- * IEEE80211_HW_DEVICE_HIDES_WEP flag.
- */
-#define IEEE80211_HW_DEVICE_STRIPS_MIC (1<<8)
-
- /* Device is capable of performing full monitor mode even during
- * normal operation. */
-#define IEEE80211_HW_MONITOR_DURING_OPER (1<<9)
-
- /* Device does not need BSSID filter set to broadcast in order to
- * receive all probe responses while scanning */
-#define IEEE80211_HW_NO_PROBE_FILTERING (1<<10)
-
- /* Channels are already configured to the default regulatory domain
- * specified in the device's EEPROM */
-#define IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED (1<<11)
-
- /* calculate Michael MIC for an MSDU when doing hwcrypto */
-#define IEEE80211_HW_TKIP_INCLUDE_MMIC (1<<12)
- /* Do TKIP phase1 key mixing in stack to support cards only do
- * phase2 key mixing when doing hwcrypto */
-#define IEEE80211_HW_TKIP_REQ_PHASE1_KEY (1<<13)
- /* Do TKIP phase1 and phase2 key mixing in stack and send the generated
- * per-packet RC4 key with each TX frame when doing hwcrypto */
-#define IEEE80211_HW_TKIP_REQ_PHASE2_KEY (1<<14)
-
- u32 flags; /* hardware flags defined above */
-
- /* Set to the size of a needed device specific skb headroom for TX skbs. */
+ u32 flags;
unsigned int extra_tx_headroom;
-
- /* This is the time in us to change channels
- */
int channel_change_time;
- /* Maximum values for various statistics.
- * Leave at 0 to indicate no support. Use negative numbers for dBm. */
- s8 max_rssi;
+ int vif_data_size;
+ u16 queues;
+ u16 ampdu_queues;
+ u16 max_listen_interval;
s8 max_signal;
- s8 max_noise;
-
- /* Number of available hardware TX queues for data packets.
- * WMM requires at least four queues. */
- int queues;
};
+/**
+ * SET_IEEE80211_DEV - set device for 802.11 hardware
+ *
+ * @hw: the &struct ieee80211_hw to set the device for
+ * @dev: the &struct device of this 802.11 device
+ */
static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
{
set_wiphy_dev(hw->wiphy, dev);
}
+/**
+ * SET_IEEE80211_PERM_ADDR - set the permanenet MAC address for 802.11 hardware
+ *
+ * @hw: the &struct ieee80211_hw to set the MAC address for
+ * @addr: the address to set
+ */
static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
{
memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
}
-/* Configuration block used by the low-level driver to tell the 802.11 code
- * about supported hardware features and to pass function pointers to callback
- * functions. */
+static inline int ieee80211_num_regular_queues(struct ieee80211_hw *hw)
+{
+ return hw->queues;
+}
+
+static inline int ieee80211_num_queues(struct ieee80211_hw *hw)
+{
+ return hw->queues + hw->ampdu_queues;
+}
+
+static inline struct ieee80211_rate *
+ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
+ const struct ieee80211_tx_info *c)
+{
+ if (WARN_ON(c->tx_rate_idx < 0))
+ return NULL;
+ return &hw->wiphy->bands[c->band]->bitrates[c->tx_rate_idx];
+}
+
+static inline struct ieee80211_rate *
+ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
+ const struct ieee80211_tx_info *c)
+{
+ if (c->control.rts_cts_rate_idx < 0)
+ return NULL;
+ return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
+}
+
+static inline struct ieee80211_rate *
+ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
+ const struct ieee80211_tx_info *c)
+{
+ if (c->control.alt_retry_rate_idx < 0)
+ return NULL;
+ return &hw->wiphy->bands[c->band]->bitrates[c->control.alt_retry_rate_idx];
+}
+
+/**
+ * DOC: Hardware crypto acceleration
+ *
+ * mac80211 is capable of taking advantage of many hardware
+ * acceleration designs for encryption and decryption operations.
+ *
+ * The set_key() callback in the &struct ieee80211_ops for a given
+ * device is called to enable hardware acceleration of encryption and
+ * decryption. The callback takes an @address parameter that will be
+ * the broadcast address for default keys, the other station's hardware
+ * address for individual keys or the zero address for keys that will
+ * be used only for transmission.
+ * Multiple transmission keys with the same key index may be used when
+ * VLANs are configured for an access point.
+ *
+ * The @local_address parameter will always be set to our own address,
+ * this is only relevant if you support multiple local addresses.
+ *
+ * When transmitting, the TX control data will use the @hw_key_idx
+ * selected by the driver by modifying the &struct ieee80211_key_conf
+ * pointed to by the @key parameter to the set_key() function.
+ *
+ * The set_key() call for the %SET_KEY command should return 0 if
+ * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
+ * added; if you return 0 then hw_key_idx must be assigned to the
+ * hardware key index, you are free to use the full u8 range.
+ *
+ * When the cmd is %DISABLE_KEY then it must succeed.
+ *
+ * Note that it is permissible to not decrypt a frame even if a key
+ * for it has been uploaded to hardware, the stack will not make any
+ * decision based on whether a key has been uploaded or not but rather
+ * based on the receive flags.
+ *
+ * The &struct ieee80211_key_conf structure pointed to by the @key
+ * parameter is guaranteed to be valid until another call to set_key()
+ * removes it, but it can only be used as a cookie to differentiate
+ * keys.
+ *
+ * In TKIP some HW need to be provided a phase 1 key, for RX decryption
+ * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
+ * handler.
+ * The update_tkip_key() call updates the driver with the new phase 1 key.
+ * This happens everytime the iv16 wraps around (every 65536 packets). The
+ * set_key() call will happen only once for each key (unless the AP did
+ * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is
+ * provided by udpate_tkip_key only. The trigger that makes mac80211 call this
+ * handler is software decryption with wrap around of iv16.
+ */
+
+/**
+ * DOC: Frame filtering
+ *
+ * mac80211 requires to see many management frames for proper
+ * operation, and users may want to see many more frames when
+ * in monitor mode. However, for best CPU usage and power consumption,
+ * having as few frames as possible percolate through the stack is
+ * desirable. Hence, the hardware should filter as much as possible.
+ *
+ * To achieve this, mac80211 uses filter flags (see below) to tell
+ * the driver's configure_filter() function which frames should be
+ * passed to mac80211 and which should be filtered out.
+ *
+ * The configure_filter() callback is invoked with the parameters
+ * @mc_count and @mc_list for the combined multicast address list
+ * of all virtual interfaces, @changed_flags telling which flags
+ * were changed and @total_flags with the new flag states.
+ *
+ * If your device has no multicast address filters your driver will
+ * need to check both the %FIF_ALLMULTI flag and the @mc_count
+ * parameter to see whether multicast frames should be accepted
+ * or dropped.
+ *
+ * All unsupported flags in @total_flags must be cleared.
+ * Hardware does not support a flag if it is incapable of _passing_
+ * the frame to the stack. Otherwise the driver must ignore
+ * the flag, but not clear it.
+ * You must _only_ clear the flag (announce no support for the
+ * flag to mac80211) if you are not able to pass the packet type
+ * to the stack (so the hardware always filters it).
+ * So for example, you should clear @FIF_CONTROL, if your hardware
+ * always filters control frames. If your hardware always passes
+ * control frames to the kernel and is incapable of filtering them,
+ * you do _not_ clear the @FIF_CONTROL flag.
+ * This rule applies to all other FIF flags as well.
+ */
+
+/**
+ * enum ieee80211_filter_flags - hardware filter flags
+ *
+ * These flags determine what the filter in hardware should be
+ * programmed to let through and what should not be passed to the
+ * stack. It is always safe to pass more frames than requested,
+ * but this has negative impact on power consumption.
+ *
+ * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS,
+ * think of the BSS as your network segment and then this corresponds
+ * to the regular ethernet device promiscuous mode.
+ *
+ * @FIF_ALLMULTI: pass all multicast frames, this is used if requested
+ * by the user or if the hardware is not capable of filtering by
+ * multicast address.
+ *
+ * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
+ * %RX_FLAG_FAILED_FCS_CRC for them)
+ *
+ * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
+ * the %RX_FLAG_FAILED_PLCP_CRC for them
+ *
+ * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
+ * to the hardware that it should not filter beacons or probe responses
+ * by BSSID. Filtering them can greatly reduce the amount of processing
+ * mac80211 needs to do and the amount of CPU wakeups, so you should
+ * honour this flag if possible.
+ *
+ * @FIF_CONTROL: pass control frames, if PROMISC_IN_BSS is not set then
+ * only those addressed to this station
+ *
+ * @FIF_OTHER_BSS: pass frames destined to other BSSes
+ */
+enum ieee80211_filter_flags {
+ FIF_PROMISC_IN_BSS = 1<<0,
+ FIF_ALLMULTI = 1<<1,
+ FIF_FCSFAIL = 1<<2,
+ FIF_PLCPFAIL = 1<<3,
+ FIF_BCN_PRBRESP_PROMISC = 1<<4,
+ FIF_CONTROL = 1<<5,
+ FIF_OTHER_BSS = 1<<6,
+};
+
+/**
+ * enum ieee80211_ampdu_mlme_action - A-MPDU actions
+ *
+ * These flags are used with the ampdu_action() callback in
+ * &struct ieee80211_ops to indicate which action is needed.
+ * @IEEE80211_AMPDU_RX_START: start Rx aggregation
+ * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
+ * @IEEE80211_AMPDU_TX_START: start Tx aggregation
+ * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation
+ */
+enum ieee80211_ampdu_mlme_action {
+ IEEE80211_AMPDU_RX_START,
+ IEEE80211_AMPDU_RX_STOP,
+ IEEE80211_AMPDU_TX_START,
+ IEEE80211_AMPDU_TX_STOP,
+};
+
+/**
+ * struct ieee80211_ops - callbacks from mac80211 to the driver
+ *
+ * This structure contains various callbacks that the driver may
+ * handle or, in some cases, must handle, for example to configure
+ * the hardware to a new channel or to transmit a frame.
+ *
+ * @tx: Handler that 802.11 module calls for each transmitted frame.
+ * skb contains the buffer starting from the IEEE 802.11 header.
+ * The low-level driver should send the frame out based on
+ * configuration in the TX control data. This handler should,
+ * preferably, never fail and stop queues appropriately, more
+ * importantly, however, it must never fail for A-MPDU-queues.
+ * Must be implemented and atomic.
+ *
+ * @start: Called before the first netdevice attached to the hardware
+ * is enabled. This should turn on the hardware and must turn on
+ * frame reception (for possibly enabled monitor interfaces.)
+ * Returns negative error codes, these may be seen in userspace,
+ * or zero.
+ * When the device is started it should not have a MAC address
+ * to avoid acknowledging frames before a non-monitor device
+ * is added.
+ * Must be implemented.
+ *
+ * @stop: Called after last netdevice attached to the hardware
+ * is disabled. This should turn off the hardware (at least
+ * it must turn off frame reception.)
+ * May be called right after add_interface if that rejects
+ * an interface.
+ * Must be implemented.
+ *
+ * @add_interface: Called when a netdevice attached to the hardware is
+ * enabled. Because it is not called for monitor mode devices, @open
+ * and @stop must be implemented.
+ * The driver should perform any initialization it needs before
+ * the device can be enabled. The initial configuration for the
+ * interface is given in the conf parameter.
+ * The callback may refuse to add an interface by returning a
+ * negative error code (which will be seen in userspace.)
+ * Must be implemented.
+ *
+ * @remove_interface: Notifies a driver that an interface is going down.
+ * The @stop callback is called after this if it is the last interface
+ * and no monitor interfaces are present.
+ * When all interfaces are removed, the MAC address in the hardware
+ * must be cleared so the device no longer acknowledges packets,
+ * the mac_addr member of the conf structure is, however, set to the
+ * MAC address of the device going away.
+ * Hence, this callback must be implemented.
+ *
+ * @config: Handler for configuration requests. IEEE 802.11 code calls this
+ * function to change hardware configuration, e.g., channel.
+ *
+ * @config_interface: Handler for configuration requests related to interfaces
+ * (e.g. BSSID changes.)
+ *
+ * @bss_info_changed: Handler for configuration requests related to BSS
+ * parameters that may vary during BSS's lifespan, and may affect low
+ * level driver (e.g. assoc/disassoc status, erp parameters).
+ * This function should not be used if no BSS has been set, unless
+ * for association indication. The @changed parameter indicates which
+ * of the bss parameters has changed when a call is made.
+ *
+ * @configure_filter: Configure the device's RX filter.
+ * See the section "Frame filtering" for more information.
+ * This callback must be implemented and atomic.
+ *
+ * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
+ * must be set or cleared for a given AID. Must be atomic.
+ *
+ * @set_key: See the section "Hardware crypto acceleration"
+ * This callback can sleep, and is only called between add_interface
+ * and remove_interface calls, i.e. while the interface with the
+ * given local_address is enabled.
+ *
+ * @update_tkip_key: See the section "Hardware crypto acceleration"
+ * This callback will be called in the context of Rx. Called for drivers
+ * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY.
+ *
+ * @hw_scan: Ask the hardware to service the scan request, no need to start
+ * the scan state machine in stack. The scan must honour the channel
+ * configuration done by the regulatory agent in the wiphy's registered
+ * bands.
+ *
+ * @get_stats: return low-level statistics
+ *
+ * @get_tkip_seq: If your device implements TKIP encryption in hardware this
+ * callback should be provided to read the TKIP transmit IVs (both IV32
+ * and IV16) for the given key from hardware.
+ *
+ * @set_rts_threshold: Configuration of RTS threshold (if device needs it)
+ *
+ * @set_frag_threshold: Configuration of fragmentation threshold. Assign this if
+ * the device does fragmentation by itself; if this method is assigned then
+ * the stack will not do fragmentation.
+ *
+ * @set_retry_limit: Configuration of retry limits (if device needs it)
+ *
+ * @sta_notify: Notifies low level driver about addition or removal
+ * of assocaited station or AP.
+ *
+ * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
+ * bursting) for a hardware TX queue. Must be atomic.
+ *
+ * @get_tx_stats: Get statistics of the current TX queue status. This is used
+ * to get number of currently queued packets (queue length), maximum queue
+ * size (limit), and total number of packets sent using each TX queue
+ * (count). The 'stats' pointer points to an array that has hw->queues +
+ * hw->ampdu_queues items.
+ *
+ * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
+ * this is only used for IBSS mode debugging and, as such, is not a
+ * required function. Must be atomic.
+ *
+ * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
+ * with other STAs in the IBSS. This is only used in IBSS mode. This
+ * function is optional if the firmware/hardware takes full care of
+ * TSF synchronization.
+ *
+ * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
+ * This is needed only for IBSS mode and the result of this function is
+ * used to determine whether to reply to Probe Requests.
+ *
+ * @conf_ht: Configures low level driver with 802.11n HT data. Must be atomic.
+ *
+ * @ampdu_action: Perform a certain A-MPDU action
+ * The RA/TID combination determines the destination and TID we want
+ * the ampdu action to be performed for. The action is defined through
+ * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
+ * is the first frame we expect to perform the action on. notice
+ * that TX/RX_STOP can pass NULL for this parameter.
+ */
struct ieee80211_ops {
- /* Handler that 802.11 module calls for each transmitted frame.
- * skb contains the buffer starting from the IEEE 802.11 header.
- * The low-level driver should send the frame out based on
- * configuration in the TX control data.
- * Must be atomic. */
- int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb,
- struct ieee80211_tx_control *control);
-
- /* Handler that is called when any netdevice attached to the hardware
- * device is set UP for the first time. This can be used, e.g., to
- * enable interrupts and beacon sending. */
- int (*open)(struct ieee80211_hw *hw);
-
- /* Handler that is called when the last netdevice attached to the
- * hardware device is set DOWN. This can be used, e.g., to disable
- * interrupts and beacon sending. */
- int (*stop)(struct ieee80211_hw *hw);
-
- /* Handler for asking a driver if a new interface can be added (or,
- * more exactly, set UP). If the handler returns zero, the interface
- * is added. Driver should perform any initialization it needs prior
- * to returning zero. By returning non-zero addition of the interface
- * is inhibited. Unless monitor_during_oper is set, it is guaranteed
- * that monitor interfaces and normal interfaces are mutually
- * exclusive. If assigned, the open() handler is called after
- * add_interface() if this is the first device added. The
- * add_interface() callback has to be assigned because it is the only
- * way to obtain the requested MAC address for any interface.
- */
+ int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
+ int (*start)(struct ieee80211_hw *hw);
+ void (*stop)(struct ieee80211_hw *hw);
int (*add_interface)(struct ieee80211_hw *hw,
struct ieee80211_if_init_conf *conf);
-
- /* Notify a driver that an interface is going down. The stop() handler
- * is called prior to this if this is a last interface. */
void (*remove_interface)(struct ieee80211_hw *hw,
struct ieee80211_if_init_conf *conf);
-
- /* Handler for configuration requests. IEEE 802.11 code calls this
- * function to change hardware configuration, e.g., channel. */
int (*config)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
-
- /* Handler for configuration requests related to interfaces (e.g.
- * BSSID). */
int (*config_interface)(struct ieee80211_hw *hw,
- int if_id, struct ieee80211_if_conf *conf);
-
- /* ieee80211 drivers do not have access to the &struct net_device
- * that is (are) connected with their device. Hence (and because
- * we need to combine the multicast lists and flags for multiple
- * virtual interfaces), they cannot assign set_multicast_list.
- * The parameters here replace dev->flags and dev->mc_count,
- * dev->mc_list is replaced by calling ieee80211_get_mc_list_item.
- * Must be atomic. */
- void (*set_multicast_list)(struct ieee80211_hw *hw,
- unsigned short flags, int mc_count);
-
- /* Set TIM bit handler. If the hardware/firmware takes care of beacon
- * generation, IEEE 802.11 code uses this function to tell the
- * low-level to set (or clear if set==0) TIM bit for the given aid. If
- * host system is used to generate beacons, this handler is not used
- * and low-level driver should set it to NULL.
- * Must be atomic. */
+ struct ieee80211_vif *vif,
+ struct ieee80211_if_conf *conf);
+ void (*bss_info_changed)(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ struct ieee80211_bss_conf *info,
+ u32 changed);
+ void (*configure_filter)(struct ieee80211_hw *hw,
+ unsigned int changed_flags,
+ unsigned int *total_flags,
+ int mc_count, struct dev_addr_list *mc_list);
int (*set_tim)(struct ieee80211_hw *hw, int aid, int set);
-
- /*
- * Set encryption key.
- *
- * This is called to enable hardware acceleration of encryption and
- * decryption. The address will be the broadcast address for default
- * keys, the other station's hardware address for individual keys or
- * the zero address for keys that will be used only for transmission.
- *
- * The local_address parameter will always be set to our own address,
- * this is only relevant if you support multiple local addresses.
- *
- * When transmitting, the TX control data will use the hw_key_idx
- * selected by the low-level driver.
- *
- * Return 0 if the key is now in use, -EOPNOTSUPP or -ENOSPC if it
- * couldn't be added; if you return 0 then hw_key_idx must be
- * assigned to something other than HW_KEY_IDX_INVALID. When the cmd
- * is DISABLE_KEY then it must succeed.
- *
- * This callback can sleep, and is only called between add_interface
- * and remove_interface calls, i.e. while the interface with the
- * given local_address is enabled.
- *
- * The ieee80211_key_conf structure pointed to by the key parameter
- * is guaranteed to be valid until another call to set_key removes
- * it, but it can only be used as a cookie to differentiate keys.
- */
- int (*set_key)(struct ieee80211_hw *hw, set_key_cmd cmd,
+ int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
const u8 *local_address, const u8 *address,
struct ieee80211_key_conf *key);
-
- /*
- * Set TX key index for default/broadcast keys. This is needed in cases
- * where wlan card is doing full WEP/TKIP encapsulation (wep_include_iv
- * is not set), in other cases, this function pointer can be set to
- * NULL since the IEEE 802.11 module takes care of selecting the key
- * index for each TX frame.
- *
- * TODO: If you use this callback in your driver tell us if you need
- * any other information from it to make it easier, like the
- * key_conf instead.
- */
- int (*set_key_idx)(struct ieee80211_hw *hw, int idx);
-
- /* Enable/disable IEEE 802.1X. This item requests wlan card to pass
- * unencrypted EAPOL-Key frames even when encryption is configured.
- * If the wlan card does not require such a configuration, this
- * function pointer can be set to NULL. */
- int (*set_ieee8021x)(struct ieee80211_hw *hw, int use_ieee8021x);
-
- /* Set port authorization state (IEEE 802.1X PAE) to be authorized
- * (authorized=1) or unauthorized (authorized=0). This function can be
- * used if the wlan hardware or low-level driver implements PAE.
- * 80211.o module will anyway filter frames based on authorization
- * state, so this function pointer can be NULL if low-level driver does
- * not require event notification about port state changes.
- * Currently unused. */
- int (*set_port_auth)(struct ieee80211_hw *hw, u8 *addr,
- int authorized);
-
- /* Ask the hardware to service the scan request, no need to start
- * the scan state machine in stack. */
+ void (*update_tkip_key)(struct ieee80211_hw *hw,
+ struct ieee80211_key_conf *conf, const u8 *address,
+ u32 iv32, u16 *phase1key);
int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len);
-
- /* return low-level statistics */
int (*get_stats)(struct ieee80211_hw *hw,
struct ieee80211_low_level_stats *stats);
-
- /* For devices that generate their own beacons and probe response
- * or association responses this updates the state of privacy_invoked
- * returns 0 for success or an error number */
- int (*set_privacy_invoked)(struct ieee80211_hw *hw,
- int privacy_invoked);
-
- /* For devices that have internal sequence counters, allow 802.11
- * code to access the current value of a counter */
- int (*get_sequence_counter)(struct ieee80211_hw *hw,
- u8* addr, u8 keyidx, u8 txrx,
- u32* iv32, u16* iv16);
-
- /* Configuration of RTS threshold (if device needs it) */
+ void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx,
+ u32 *iv32, u16 *iv16);
int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
-
- /* Configuration of fragmentation threshold.
- * Assign this if the device does fragmentation by itself,
- * if this method is assigned then the stack will not do
- * fragmentation. */
int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
-
- /* Configuration of retry limits (if device needs it) */
int (*set_retry_limit)(struct ieee80211_hw *hw,
u32 short_retry, u32 long_retr);
-
- /* Number of STAs in STA table notification (NULL = disabled).
- * Must be atomic. */
- void (*sta_table_notification)(struct ieee80211_hw *hw,
- int num_sta);
-
- /* Handle ERP IE change notifications. Must be atomic. */
- void (*erp_ie_changed)(struct ieee80211_hw *hw, u8 changes,
- int cts_protection, int preamble);
-
- /* Flags for the erp_ie_changed changes parameter */
-#define IEEE80211_ERP_CHANGE_PROTECTION (1<<0) /* protection flag changed */
-#define IEEE80211_ERP_CHANGE_PREAMBLE (1<<1) /* barker preamble mode changed */
-
- /* Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
- * bursting) for a hardware TX queue.
- * queue = IEEE80211_TX_QUEUE_*.
- * Must be atomic. */
- int (*conf_tx)(struct ieee80211_hw *hw, int queue,
+ void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+ enum sta_notify_cmd, const u8 *addr);
+ int (*conf_tx)(struct ieee80211_hw *hw, u16 queue,
const struct ieee80211_tx_queue_params *params);
-
- /* Get statistics of the current TX queue status. This is used to get
- * number of currently queued packets (queue length), maximum queue
- * size (limit), and total number of packets sent using each TX queue
- * (count).
- * Currently unused. */
int (*get_tx_stats)(struct ieee80211_hw *hw,
struct ieee80211_tx_queue_stats *stats);
-
- /* Get the current TSF timer value from firmware/hardware. Currently,
- * this is only used for IBSS mode debugging and, as such, is not a
- * required function.
- * Must be atomic. */
u64 (*get_tsf)(struct ieee80211_hw *hw);
-
- /* Reset the TSF timer and allow firmware/hardware to synchronize with
- * other STAs in the IBSS. This is only used in IBSS mode. This
- * function is optional if the firmware/hardware takes full care of
- * TSF synchronization. */
void (*reset_tsf)(struct ieee80211_hw *hw);
-
- /* Setup beacon data for IBSS beacons. Unlike access point (Master),
- * IBSS uses a fixed beacon frame which is configured using this
- * function. This handler is required only for IBSS mode. */
- int (*beacon_update)(struct ieee80211_hw *hw,
- struct sk_buff *skb,
- struct ieee80211_tx_control *control);
-
- /* Determine whether the last IBSS beacon was sent by us. This is
- * needed only for IBSS mode and the result of this function is used to
- * determine whether to reply to Probe Requests. */
int (*tx_last_beacon)(struct ieee80211_hw *hw);
+ int (*ampdu_action)(struct ieee80211_hw *hw,
+ enum ieee80211_ampdu_mlme_action action,
+ const u8 *addr, u16 tid, u16 *ssn);
};
-/* Allocate a new hardware device. This must be called once for each
- * hardware device. The returned pointer must be used to refer to this
- * device when calling other functions. 802.11 code allocates a private data
- * area for the low-level driver. The size of this area is given as
- * priv_data_len.
+/**
+ * ieee80211_alloc_hw - Allocate a new hardware device
+ *
+ * This must be called once for each hardware device. The returned pointer
+ * must be used to refer to this device when calling other functions.
+ * mac80211 allocates a private data area for the driver pointed to by
+ * @priv in &struct ieee80211_hw, the size of this area is given as
+ * @priv_data_len.
+ *
+ * @priv_data_len: length of private data
+ * @ops: callbacks for this device
*/
struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
const struct ieee80211_ops *ops);
-/* Register hardware device to the IEEE 802.11 code and kernel. Low-level
- * drivers must call this function before using any other IEEE 802.11
- * function except ieee80211_register_hwmode. */
+/**
+ * ieee80211_register_hw - Register hardware device
+ *
+ * You must call this function before any other functions in
+ * mac80211. Note that before a hardware can be registered, you
+ * need to fill the contained wiphy's information.
+ *
+ * @hw: the device to register as returned by ieee80211_alloc_hw()
+ */
int ieee80211_register_hw(struct ieee80211_hw *hw);
-/* driver can use this and ieee80211_get_rx_led_name to get the
- * name of the registered LEDs after ieee80211_register_hw
- * was called.
- * This is useful to set the default trigger on the LED class
- * device that your driver should export for each LED the device
- * has, that way the default behaviour will be as expected but
- * the user can still change it/turn off the LED etc.
- */
#ifdef CONFIG_MAC80211_LEDS
extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
+extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
+extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
#endif
+/**
+ * ieee80211_get_tx_led_name - get name of TX LED
+ *
+ * mac80211 creates a transmit LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
#endif
}
+/**
+ * ieee80211_get_rx_led_name - get name of RX LED
+ *
+ * mac80211 creates a receive LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
#endif
}
-/* Register a new hardware PHYMODE capability to the stack. */
-int ieee80211_register_hwmode(struct ieee80211_hw *hw,
- struct ieee80211_hw_mode *mode);
+/**
+ * ieee80211_get_assoc_led_name - get name of association LED
+ *
+ * mac80211 creates a association LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
+static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_LEDS
+ return __ieee80211_get_assoc_led_name(hw);
+#else
+ return NULL;
+#endif
+}
-/* Unregister a hardware device. This function instructs 802.11 code to free
- * allocated resources and unregister netdevices from the kernel. */
+/**
+ * ieee80211_get_radio_led_name - get name of radio LED
+ *
+ * mac80211 creates a radio change LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
+static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_LEDS
+ return __ieee80211_get_radio_led_name(hw);
+#else
+ return NULL;
+#endif
+}
+
+/**
+ * ieee80211_unregister_hw - Unregister a hardware device
+ *
+ * This function instructs mac80211 to free allocated resources
+ * and unregister netdevices from the networking subsystem.
+ *
+ * @hw: the hardware to unregister
+ */
void ieee80211_unregister_hw(struct ieee80211_hw *hw);
-/* Free everything that was allocated including private data of a driver. */
+/**
+ * ieee80211_free_hw - free hardware descriptor
+ *
+ * This function frees everything that was allocated, including the
+ * private data for the driver. You must call ieee80211_unregister_hw()
+ * before calling this function.
+ *
+ * @hw: the hardware to free
+ */
void ieee80211_free_hw(struct ieee80211_hw *hw);
-/* Receive frame callback function. The low-level driver uses this function to
- * send received frames to the IEEE 802.11 code. Receive buffer (skb) must
- * start with IEEE 802.11 header. */
+/* trick to avoid symbol clashes with the ieee80211 subsystem */
void __ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb,
struct ieee80211_rx_status *status);
+
+/**
+ * ieee80211_rx - receive frame
+ *
+ * Use this function to hand received frames to mac80211. The receive
+ * buffer in @skb must start with an IEEE 802.11 header or a radiotap
+ * header if %RX_FLAG_RADIOTAP is set in the @status flags.
+ *
+ * This function may not be called in IRQ context. Calls to this function
+ * for a single hardware must be synchronized against each other. Calls
+ * to this function and ieee80211_rx_irqsafe() may not be mixed for a
+ * single hardware.
+ *
+ * @hw: the hardware this frame came in on
+ * @skb: the buffer to receive, owned by mac80211 after this call
+ * @status: status of this frame; the status pointer need not be valid
+ * after this function returns
+ */
+static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb,
+ struct ieee80211_rx_status *status)
+{
+ __ieee80211_rx(hw, skb, status);
+}
+
+/**
+ * ieee80211_rx_irqsafe - receive frame
+ *
+ * Like ieee80211_rx() but can be called in IRQ context
+ * (internally defers to a tasklet.)
+ *
+ * Calls to this function and ieee80211_rx() may not be mixed for a
+ * single hardware.
+ *
+ * @hw: the hardware this frame came in on
+ * @skb: the buffer to receive, owned by mac80211 after this call
+ * @status: status of this frame; the status pointer need not be valid
+ * after this function returns and is not freed by mac80211,
+ * it is recommended that it points to a stack area
+ */
void ieee80211_rx_irqsafe(struct ieee80211_hw *hw,
struct sk_buff *skb,
struct ieee80211_rx_status *status);
-/* Transmit status callback function. The low-level driver must call this
- * function to report transmit status for all the TX frames that had
- * req_tx_status set in the transmit control fields. In addition, this should
- * be called at least for all unicast frames to provide information for TX rate
- * control algorithm. In order to maintain all statistics, this function is
- * recommended to be called after each frame, including multicast/broadcast, is
- * sent. */
+/**
+ * ieee80211_tx_status - transmit status callback
+ *
+ * Call this function for all transmitted frames after they have been
+ * transmitted. It is permissible to not call this function for
+ * multicast frames but this can affect statistics.
+ *
+ * This function may not be called in IRQ context. Calls to this function
+ * for a single hardware must be synchronized against each other. Calls
+ * to this function and ieee80211_tx_status_irqsafe() may not be mixed
+ * for a single hardware.
+ *
+ * @hw: the hardware the frame was transmitted by
+ * @skb: the frame that was transmitted, owned by mac80211 after this call
+ */
void ieee80211_tx_status(struct ieee80211_hw *hw,
- struct sk_buff *skb,
- struct ieee80211_tx_status *status);
+ struct sk_buff *skb);
+
+/**
+ * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
+ *
+ * Like ieee80211_tx_status() but can be called in IRQ context
+ * (internally defers to a tasklet.)
+ *
+ * Calls to this function and ieee80211_tx_status() may not be mixed for a
+ * single hardware.
+ *
+ * @hw: the hardware the frame was transmitted by
+ * @skb: the frame that was transmitted, owned by mac80211 after this call
+ */
void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
- struct sk_buff *skb,
- struct ieee80211_tx_status *status);
+ struct sk_buff *skb);
/**
* ieee80211_beacon_get - beacon generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @control: will be filled with information needed to send this beacon.
*
* If the beacon frames are generated by the host system (i.e., not in
* is responsible of freeing it.
*/
struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
- int if_id,
- struct ieee80211_tx_control *control);
+ struct ieee80211_vif *vif);
/**
* ieee80211_rts_get - RTS frame generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame: pointer to the frame that is going to be protected by the RTS.
* @frame_len: the frame length (in octets).
- * @frame_txctl: &struct ieee80211_tx_control of the frame.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
* @rts: The buffer where to store the RTS frame.
*
* If the RTS frames are generated by the host system (i.e., not in
* the next RTS frame from the 802.11 code. The low-level is responsible
* for calling this function before and RTS frame is needed.
*/
-void ieee80211_rts_get(struct ieee80211_hw *hw, int if_id,
+void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
- const struct ieee80211_tx_control *frame_txctl,
+ const struct ieee80211_tx_info *frame_txctl,
struct ieee80211_rts *rts);
/**
* ieee80211_rts_duration - Get the duration field for an RTS frame
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame that is going to be protected by the RTS.
- * @frame_txctl: &struct ieee80211_tx_control of the frame.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
*
* If the RTS is generated in firmware, but the host system must provide
* the duration field, the low-level driver uses this function to receive
* the duration field value in little-endian byteorder.
*/
-__le16 ieee80211_rts_duration(struct ieee80211_hw *hw, int if_id,
- size_t frame_len,
- const struct ieee80211_tx_control *frame_txctl);
+__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif, size_t frame_len,
+ const struct ieee80211_tx_info *frame_txctl);
/**
* ieee80211_ctstoself_get - CTS-to-self frame generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame: pointer to the frame that is going to be protected by the CTS-to-self.
* @frame_len: the frame length (in octets).
- * @frame_txctl: &struct ieee80211_tx_control of the frame.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
* @cts: The buffer where to store the CTS-to-self frame.
*
* If the CTS-to-self frames are generated by the host system (i.e., not in
* the next CTS-to-self frame from the 802.11 code. The low-level is responsible
* for calling this function before and CTS-to-self frame is needed.
*/
-void ieee80211_ctstoself_get(struct ieee80211_hw *hw, int if_id,
+void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
- const struct ieee80211_tx_control *frame_txctl,
+ const struct ieee80211_tx_info *frame_txctl,
struct ieee80211_cts *cts);
/**
* ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
- * @frame_txctl: &struct ieee80211_tx_control of the frame.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
*
* If the CTS-to-self is generated in firmware, but the host system must provide
* the duration field, the low-level driver uses this function to receive
* the duration field value in little-endian byteorder.
*/
-__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, int if_id,
+__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
size_t frame_len,
- const struct ieee80211_tx_control *frame_txctl);
+ const struct ieee80211_tx_info *frame_txctl);
/**
* ieee80211_generic_frame_duration - Calculate the duration field for a frame
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame.
- * @rate: the rate (in 100kbps) at which the frame is going to be transmitted.
+ * @rate: the rate at which the frame is going to be transmitted.
*
* Calculate the duration field of some generic frame, given its
* length and transmission rate (in 100kbps).
*/
-__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, int if_id,
+__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
size_t frame_len,
- int rate);
+ struct ieee80211_rate *rate);
/**
* ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
* @hw: pointer as obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @control: will be filled with information needed to send returned frame.
*
* Function for accessing buffered broadcast and multicast frames. If
* use common code for all beacons.
*/
struct sk_buff *
-ieee80211_get_buffered_bc(struct ieee80211_hw *hw, int if_id,
- struct ieee80211_tx_control *control);
+ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
-/* Given an sk_buff with a raw 802.11 header at the data pointer this function
+/**
+ * ieee80211_get_hdrlen_from_skb - get header length from data
+ *
+ * Given an skb with a raw 802.11 header at the data pointer this function
* returns the 802.11 header length in bytes (not including encryption
* headers). If the data in the sk_buff is too short to contain a valid 802.11
* header the function returns 0.
+ *
+ * @skb: the frame
*/
-int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);
+unsigned int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);
-/* Like ieee80211_get_hdrlen_from_skb() but takes a FC in CPU order. */
+/**
+ * ieee80211_get_hdrlen - get header length from frame control
+ *
+ * This function returns the 802.11 header length in bytes (not including
+ * encryption headers.)
+ *
+ * @fc: the frame control field (in CPU endianness)
+ */
int ieee80211_get_hdrlen(u16 fc);
/**
+ * ieee80211_hdrlen - get header length in bytes from frame control
+ * @fc: frame control field in little-endian format
+ */
+unsigned int ieee80211_hdrlen(__le16 fc);
+
+/**
+ * ieee80211_get_tkip_key - get a TKIP rc4 for skb
+ *
+ * This function computes a TKIP rc4 key for an skb. It computes
+ * a phase 1 key if needed (iv16 wraps around). This function is to
+ * be used by drivers which can do HW encryption but need to compute
+ * to phase 1/2 key in SW.
+ *
+ * @keyconf: the parameter passed with the set key
+ * @skb: the skb for which the key is needed
+ * @rc4key: a buffer to which the key will be written
+ * @type: TBD
+ * @key: TBD
+ */
+void ieee80211_get_tkip_key(struct ieee80211_key_conf *keyconf,
+ struct sk_buff *skb,
+ enum ieee80211_tkip_key_type type, u8 *key);
+/**
* ieee80211_wake_queue - wake specific queue
* @hw: pointer as obtained from ieee80211_alloc_hw().
* @queue: queue number (counted from zero).
void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
/**
- * ieee80211_start_queues - start all queues
- * @hw: pointer to as obtained from ieee80211_alloc_hw().
- *
- * Drivers should use this function instead of netif_start_queue.
- */
-void ieee80211_start_queues(struct ieee80211_hw *hw);
-
-/**
* ieee80211_stop_queues - stop all queues
* @hw: pointer as obtained from ieee80211_alloc_hw().
*
void ieee80211_wake_queues(struct ieee80211_hw *hw);
/**
- * ieee80211_get_mc_list_item - iteration over items in multicast list
- * @hw: pointer as obtained from ieee80211_alloc_hw().
- * @prev: value returned by previous call to ieee80211_get_mc_list_item() or
- * NULL to start a new iteration.
- * @ptr: pointer to buffer of void * type for internal usage of
- * ieee80211_get_mc_list_item().
- *
- * Iterates over items in multicast list of given device. To get the first
- * item, pass NULL in @prev and in *@ptr. In subsequent calls, pass the
- * value returned by previous call in @prev. Don't alter *@ptr during
- * iteration. When there are no more items, NULL is returned.
- */
-struct dev_mc_list *
-ieee80211_get_mc_list_item(struct ieee80211_hw *hw,
- struct dev_mc_list *prev,
- void **ptr);
-
-/* called by driver to notify scan status completed */
+ * ieee80211_scan_completed - completed hardware scan
+ *
+ * When hardware scan offload is used (i.e. the hw_scan() callback is
+ * assigned) this function needs to be called by the driver to notify
+ * mac80211 that the scan finished.
+ *
+ * @hw: the hardware that finished the scan
+ */
void ieee80211_scan_completed(struct ieee80211_hw *hw);
-/* return a pointer to the source address (SA) */
-static inline u8 *ieee80211_get_SA(struct ieee80211_hdr *hdr)
-{
- u8 *raw = (u8 *) hdr;
- u8 tofrom = (*(raw+1)) & 3; /* get the TODS and FROMDS bits */
-
- switch (tofrom) {
- case 2:
- return hdr->addr3;
- case 3:
- return hdr->addr4;
- }
- return hdr->addr2;
-}
+/**
+ * ieee80211_iterate_active_interfaces - iterate active interfaces
+ *
+ * This function iterates over the interfaces associated with a given
+ * hardware that are currently active and calls the callback for them.
+ * This function allows the iterator function to sleep, when the iterator
+ * function is atomic @ieee80211_iterate_active_interfaces_atomic can
+ * be used.
+ *
+ * @hw: the hardware struct of which the interfaces should be iterated over
+ * @iterator: the iterator function to call
+ * @data: first argument of the iterator function
+ */
+void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw,
+ void (*iterator)(void *data, u8 *mac,
+ struct ieee80211_vif *vif),
+ void *data);
-/* return a pointer to the destination address (DA) */
-static inline u8 *ieee80211_get_DA(struct ieee80211_hdr *hdr)
-{
- u8 *raw = (u8 *) hdr;
- u8 to_ds = (*(raw+1)) & 1; /* get the TODS bit */
+/**
+ * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
+ *
+ * This function iterates over the interfaces associated with a given
+ * hardware that are currently active and calls the callback for them.
+ * This function requires the iterator callback function to be atomic,
+ * if that is not desired, use @ieee80211_iterate_active_interfaces instead.
+ *
+ * @hw: the hardware struct of which the interfaces should be iterated over
+ * @iterator: the iterator function to call, cannot sleep
+ * @data: first argument of the iterator function
+ */
+void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
+ void (*iterator)(void *data,
+ u8 *mac,
+ struct ieee80211_vif *vif),
+ void *data);
- if (to_ds)
- return hdr->addr3;
- return hdr->addr1;
-}
+/**
+ * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient
+ * @tid: the TID to BA on.
+ * @return: success if addBA request was sent, failure otherwise
+ *
+ * Although mac80211/low level driver/user space application can estimate
+ * the need to start aggregation on a certain RA/TID, the session level
+ * will be managed by the mac80211.
+ */
+int ieee80211_start_tx_ba_session(struct ieee80211_hw *hw, u8 *ra, u16 tid);
-static inline int ieee80211_get_morefrag(struct ieee80211_hdr *hdr)
-{
- return (le16_to_cpu(hdr->frame_control) &
- IEEE80211_FCTL_MOREFRAGS) != 0;
-}
+/**
+ * ieee80211_start_tx_ba_cb - low level driver ready to aggregate.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session.
+ */
+void ieee80211_start_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u16 tid);
+
+/**
+ * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session.
+ * This version of the function is IRQ-safe.
+ */
+void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
+ u16 tid);
+
+/**
+ * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient
+ * @tid: the TID to stop BA.
+ * @initiator: if indicates initiator DELBA frame will be sent.
+ * @return: error if no sta with matching da found, success otherwise
+ *
+ * Although mac80211/low level driver/user space application can estimate
+ * the need to stop aggregation on a certain RA/TID, the session level
+ * will be managed by the mac80211.
+ */
+int ieee80211_stop_tx_ba_session(struct ieee80211_hw *hw,
+ u8 *ra, u16 tid,
+ enum ieee80211_back_parties initiator);
-#define MAC_FMT "%02x:%02x:%02x:%02x:%02x:%02x"
-#define MAC_ARG(x) ((u8*)(x))[0], ((u8*)(x))[1], ((u8*)(x))[2], \
- ((u8*)(x))[3], ((u8*)(x))[4], ((u8*)(x))[5]
+/**
+ * ieee80211_stop_tx_ba_cb - low level driver ready to stop aggregate.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the desired TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session tear down.
+ */
+void ieee80211_stop_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u8 tid);
+/**
+ * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the desired TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session tear down.
+ * This version of the function is IRQ-safe.
+ */
+void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
+ u16 tid);
+
+/**
+ * ieee80211_notify_mac - low level driver notification
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @notif_type: enum ieee80211_notification_types
+ *
+ * This function must be called by low level driver to inform mac80211 of
+ * low level driver status change or force mac80211 to re-assoc for low
+ * level driver internal error that require re-assoc.
+ */
+void ieee80211_notify_mac(struct ieee80211_hw *hw,
+ enum ieee80211_notification_types notif_type);
#endif /* MAC80211_H */