* @aid: association ID number, valid only when @assoc is true
* @use_cts_prot: use CTS protection
* @use_short_preamble: use 802.11b short preamble
+ * @dtim_period: num of beacons before the next DTIM, for PSM
* @timestamp: beacon timestamp
* @beacon_int: beacon interval
- * @assoc_capability: capabbilities taken from assoc resp
+ * @assoc_capability: capabilities taken from assoc resp
* @assoc_ht: association in HT mode
* @ht_conf: ht capabilities
* @ht_bss_conf: ht extended capabilities
/* erp related data */
bool use_cts_prot;
bool use_short_preamble;
+ u8 dtim_period;
u16 beacon_int;
u16 assoc_capability;
u64 timestamp;
* These flags are used with the @flags member of &ieee80211_tx_info.
*
* @IEEE80211_TX_CTL_REQ_TX_STATUS: request TX status callback for this frame.
- * @IEEE80211_TX_CTL_DO_NOT_ENCRYPT: send this frame without encryption;
- * e.g., for EAPOL frame
* @IEEE80211_TX_CTL_USE_RTS_CTS: use RTS-CTS before sending frame
* @IEEE80211_TX_CTL_USE_CTS_PROTECT: use CTS protection for the frame (e.g.,
* for combined 802.11g / 802.11b networks)
* @IEEE80211_TX_CTL_SHORT_PREAMBLE: TBD
* @IEEE80211_TX_CTL_LONG_RETRY_LIMIT: this frame should be send using the
* through set_retry_limit configured long retry value
- * @IEEE80211_TX_CTL_EAPOL_FRAME: internal to mac80211
* @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
* @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
* @IEEE80211_TX_CTL_OFDM_HT: this frame can be sent in HT OFDM rates. number
*/
enum mac80211_tx_control_flags {
IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
- IEEE80211_TX_CTL_DO_NOT_ENCRYPT = BIT(1),
IEEE80211_TX_CTL_USE_RTS_CTS = BIT(2),
IEEE80211_TX_CTL_USE_CTS_PROTECT = BIT(3),
IEEE80211_TX_CTL_NO_ACK = BIT(4),
IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(8),
IEEE80211_TX_CTL_SHORT_PREAMBLE = BIT(9),
IEEE80211_TX_CTL_LONG_RETRY_LIMIT = BIT(10),
- IEEE80211_TX_CTL_EAPOL_FRAME = BIT(11),
IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(12),
IEEE80211_TX_CTL_AMPDU = BIT(13),
IEEE80211_TX_CTL_OFDM_HT = BIT(14),
struct ieee80211_vif *vif;
struct ieee80211_key_conf *hw_key;
unsigned long jiffies;
- int ifindex;
u16 aid;
s8 rts_cts_rate_idx, alt_retry_rate_idx;
u8 retry_limit;
* @radio_enabled: when zero, driver is required to switch off the radio.
* TODO make a flag
* @beacon_int: beacon interval (TODO make interface config)
+ * @listen_interval: listen interval in units of beacon interval
* @flags: configuration flags defined above
* @power_level: requested transmit power (in dBm)
* @max_antenna_gain: maximum antenna gain (in dBi)
int radio_enabled;
int beacon_int;
+ u16 listen_interval;
u32 flags;
int power_level;
int max_antenna_gain;
* rely on the host system for such buffering. This option is used
* to configure the IEEE 802.11 upper layer to buffer broadcast and
* multicast frames when there are power saving stations so that
- * the driver can fetch them with ieee80211_get_buffered_bc(). Note
- * that not setting this flag works properly only when the
- * %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because
- * otherwise the stack will not know when the DTIM beacon was sent.
+ * the driver can fetch them with ieee80211_get_buffered_bc().
*
* @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
* Hardware is not capable of short slot operation on the 2.4 GHz band.
* Measurement, Channel Switch, Quieting, TPC
*/
enum ieee80211_hw_flags {
- IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0,
IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
* @max_signal: Maximum value for signal (rssi) in RX information, used
* only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
*
+ * @max_listen_interval: max listen interval in units of beacon interval
+ * that HW supports
+ *
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four, these
* queues need to have configurable access parameters.
unsigned int extra_tx_headroom;
int channel_change_time;
int vif_data_size;
- u16 queues, ampdu_queues;
+ u16 queues;
+ u16 ampdu_queues;
+ u16 max_listen_interval;
s8 max_signal;
};
static inline int ieee80211_num_regular_queues(struct ieee80211_hw *hw)
{
-#ifdef CONFIG_MAC80211_QOS
return hw->queues;
-#else
- return 1;
-#endif
}
static inline int ieee80211_num_queues(struct ieee80211_hw *hw)
{
-#ifdef CONFIG_MAC80211_QOS
return hw->queues + hw->ampdu_queues;
-#else
- return 1;
-#endif
}
static inline struct ieee80211_rate *
* See the section "Frame filtering" for more information.
* This callback must be implemented and atomic.
*
- * @set_tim: Set TIM bit. If the hardware/firmware takes care of beacon
- * generation (that is, %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is set)
- * mac80211 calls this function when a TIM bit must be set or cleared
- * for a given AID. Must be atomic.
+ * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
+ * must be set or cleared for a given AID. Must be atomic.
*
* @set_key: See the section "Hardware crypto acceleration"
* This callback can sleep, and is only called between add_interface
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff