BSS_CHANGED_BEACON_ENABLED = 1<<9,
BSS_CHANGED_CQM = 1<<10,
BSS_CHANGED_IBSS = 1<<11,
+
+ /* when adding here, make sure to change ieee80211_reconfig */
};
/**
* the current band.
* @bssid: The BSSID for this BSS
* @enable_beacon: whether beaconing should be enabled or not
+ * @channel_type: Channel type for this BSS -- the hardware might be
+ * configured for HT40+ while this BSS only uses no-HT, for
+ * example.
* @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info).
* This field is only valid when the channel type is one of the HT types.
* @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
u16 ht_operation_mode;
s32 cqm_rssi_thold;
u32 cqm_rssi_hyst;
+ enum nl80211_channel_type channel_type;
};
/**
* @signal: signal strength when receiving this frame, either in dBm, in dB or
* unspecified depending on the hardware capabilities flags
* @IEEE80211_HW_SIGNAL_*
- * @noise: noise when receiving this frame, in dBm (DEPRECATED).
* @antenna: antenna used
* @rate_idx: index of data rate into band's supported rates or MCS index if
* HT rates are use (RX_FLAG_HT)
enum ieee80211_band band;
int freq;
int signal;
- int noise __deprecated;
int antenna;
int rate_idx;
int flag;
};
/**
+ * struct ieee80211_channel_switch - holds the channel switch data
+ *
+ * The information provided in this structure is required for channel switch
+ * operation.
+ *
+ * @timestamp: value in microseconds of the 64-bit Time Synchronization
+ * Function (TSF) timer when the frame containing the channel switch
+ * announcement was received. This is simply the rx.mactime parameter
+ * the driver passed into mac80211.
+ * @block_tx: Indicates whether transmission must be blocked before the
+ * scheduled channel switch, as indicated by the AP.
+ * @channel: the new channel to switch to
+ * @count: the number of TBTT's until the channel switch event
+ */
+struct ieee80211_channel_switch {
+ u64 timestamp;
+ bool block_tx;
+ struct ieee80211_channel *channel;
+ u8 count;
+};
+
+/**
* struct ieee80211_vif - per-interface data
*
* Data in this structure is continually present for driver
* encrypted in hardware.
* @alg: The key algorithm.
* @flags: key flags, see &enum ieee80211_key_flags.
+ * @ap_addr: AP's MAC address
* @keyidx: the key index (0-3)
* @keylen: key material length
* @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
u8 iv_len;
u8 hw_key_idx;
u8 flags;
- u8 *ap_addr;
s8 keyidx;
u8 keylen;
u8 key[0];
* one milliwatt. This is the preferred method since it is standardized
* between different devices. @max_signal does not need to be set.
*
- * @IEEE80211_HW_NOISE_DBM:
- * Hardware can provide noise (radio interference) values in units dBm,
- * decibel difference from one milliwatt.
- *
* @IEEE80211_HW_SPECTRUM_MGMT:
* Hardware supports spectrum management defined in 802.11h
* Measurement, Channel Switch, Quieting, TPC
IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
IEEE80211_HW_SIGNAL_UNSPEC = 1<<5,
IEEE80211_HW_SIGNAL_DBM = 1<<6,
- IEEE80211_HW_NOISE_DBM = 1<<7,
+ /* use this hole */
IEEE80211_HW_SPECTRUM_MGMT = 1<<8,
IEEE80211_HW_AMPDU_AGGREGATION = 1<<9,
IEEE80211_HW_SUPPORTS_PS = 1<<10,
* Returns a negative error code on failure.
* The callback must be atomic.
*
+ * @get_survey: Return per-channel survey information
+ *
* @rfkill_poll: Poll rfkill hardware state. If you need this, you also
* need to set wiphy->rfkill_poll to %true before registration,
* and need to call wiphy_rfkill_set_hw_state() in the callback.
* @flush: Flush all pending frames from the hardware queue, making sure
* that the hardware queues are empty. If the parameter @drop is set
* to %true, pending frames may be dropped. The callback can sleep.
+ *
+ * @channel_switch: Drivers that need (or want) to offload the channel
+ * switch operation for CSAs received from the AP may implement this
+ * callback. They must then call ieee80211_chswitch_done() to indicate
+ * completion of the channel switch.
*/
struct ieee80211_ops {
int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
struct ieee80211_bss_conf *info,
u32 changed);
u64 (*prepare_multicast)(struct ieee80211_hw *hw,
- int mc_count, struct dev_addr_list *mc_list);
+ struct netdev_hw_addr_list *mc_list);
void (*configure_filter)(struct ieee80211_hw *hw,
unsigned int changed_flags,
unsigned int *total_flags,
int (*testmode_cmd)(struct ieee80211_hw *hw, void *data, int len);
#endif
void (*flush)(struct ieee80211_hw *hw, bool drop);
+ void (*channel_switch)(struct ieee80211_hw *hw,
+ struct ieee80211_channel_switch *ch_switch);
};
/**
enum nl80211_cqm_rssi_threshold_event rssi_event,
gfp_t gfp);
+/**
+ * ieee80211_chswitch_done - Complete channel switch process
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ * @success: make the channel switch successful or not
+ *
+ * Complete the channel switch post-process: set the new operational channel
+ * and wake up the suspended queues.
+ */
+void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success);
+
/* Rate control API */
/**