* @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
* enabled/disabled (beaconing modes)
* @BSS_CHANGED_CQM: Connection quality monitor config changed
+ * @BSS_CHANGED_IBSS: IBSS join status changed
*/
enum ieee80211_bss_change {
BSS_CHANGED_ASSOC = 1<<0,
BSS_CHANGED_BEACON = 1<<8,
BSS_CHANGED_BEACON_ENABLED = 1<<9,
BSS_CHANGED_CQM = 1<<10,
+ BSS_CHANGED_IBSS = 1<<11,
};
/**
* to that BSS) that can change during the lifetime of the BSS.
*
* @assoc: association status
+ * @ibss_joined: indicates whether this station is part of an IBSS
+ * or not
* @aid: association ID number, valid only when @assoc is true
* @use_cts_prot: use CTS protection
* @use_short_preamble: use 802.11b short preamble;
struct ieee80211_bss_conf {
const u8 *bssid;
/* association related data */
- bool assoc;
+ bool assoc, ibss_joined;
u16 aid;
/* erp related data */
bool use_cts_prot;
* @signal: signal strength when receiving this frame, either in dBm, in dB or
* unspecified depending on the hardware capabilities flags
* @IEEE80211_HW_SIGNAL_*
- * @noise: noise when receiving this frame, in dBm (DEPRECATED).
* @antenna: antenna used
* @rate_idx: index of data rate into band's supported rates or MCS index if
* HT rates are use (RX_FLAG_HT)
enum ieee80211_band band;
int freq;
int signal;
- int noise __deprecated;
int antenna;
int rate_idx;
int flag;
* @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
* powersave documentation below. This variable is valid only when
* the CONF_PS flag is set.
+ * @dynamic_ps_forced_timeout: The dynamic powersave timeout (in ms) configured
+ * by cfg80211 (essentially, wext) If set, this value overrules the value
+ * chosen by mac80211 based on ps qos network latency.
*
* @power_level: requested transmit power (in dBm)
*
*/
struct ieee80211_conf {
u32 flags;
- int power_level, dynamic_ps_timeout;
+ int power_level, dynamic_ps_timeout, dynamic_ps_forced_timeout;
int max_sleep_period;
u16 listen_interval;
* one milliwatt. This is the preferred method since it is standardized
* between different devices. @max_signal does not need to be set.
*
- * @IEEE80211_HW_NOISE_DBM:
- * Hardware can provide noise (radio interference) values in units dBm,
- * decibel difference from one milliwatt.
- *
* @IEEE80211_HW_SPECTRUM_MGMT:
* Hardware supports spectrum management defined in 802.11h
* Measurement, Channel Switch, Quieting, TPC
IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
IEEE80211_HW_SIGNAL_UNSPEC = 1<<5,
IEEE80211_HW_SIGNAL_DBM = 1<<6,
- IEEE80211_HW_NOISE_DBM = 1<<7,
+ /* use this hole */
IEEE80211_HW_SPECTRUM_MGMT = 1<<8,
IEEE80211_HW_AMPDU_AGGREGATION = 1<<9,
IEEE80211_HW_SUPPORTS_PS = 1<<10,
struct ieee80211_key_conf *conf,
struct ieee80211_sta *sta,
u32 iv32, u16 *phase1key);
- int (*hw_scan)(struct ieee80211_hw *hw,
+ int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
struct cfg80211_scan_request *req);
void (*sw_scan_start)(struct ieee80211_hw *hw);
void (*sw_scan_complete)(struct ieee80211_hw *hw);