* @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
* enabled/disabled (beaconing modes)
* @BSS_CHANGED_CQM: Connection quality monitor config changed
+ * @BSS_CHANGED_IBSS: IBSS join status changed
*/
enum ieee80211_bss_change {
BSS_CHANGED_ASSOC = 1<<0,
BSS_CHANGED_BEACON = 1<<8,
BSS_CHANGED_BEACON_ENABLED = 1<<9,
BSS_CHANGED_CQM = 1<<10,
+ BSS_CHANGED_IBSS = 1<<11,
};
/**
* to that BSS) that can change during the lifetime of the BSS.
*
* @assoc: association status
+ * @ibss_joined: indicates whether this station is part of an IBSS
+ * or not
* @aid: association ID number, valid only when @assoc is true
* @use_cts_prot: use CTS protection
* @use_short_preamble: use 802.11b short preamble;
struct ieee80211_bss_conf {
const u8 *bssid;
/* association related data */
- bool assoc;
+ bool assoc, ibss_joined;
u16 aid;
/* erp related data */
bool use_cts_prot;
* MLME command (internal to mac80211 to figure out whether to send TX
* status to user space)
* @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
+ * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
+ * frame and selects the maximum number of streams that it can use.
*/
enum mac80211_tx_control_flags {
IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
IEEE80211_TX_INTFL_HAS_RADIOTAP = BIT(20),
IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21),
IEEE80211_TX_CTL_LDPC = BIT(22),
+ IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24),
+#define IEEE80211_TX_CTL_STBC_SHIFT 23
};
/**
* @status: union for status data
* @driver_data: array of driver_data pointers
* @ampdu_ack_len: number of acked aggregated frames.
- * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
+ * relevant only if IEEE80211_TX_STAT_AMPDU was set.
* @ampdu_ack_map: block ack bit map for the aggregation.
- * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
+ * relevant only if IEEE80211_TX_STAT_AMPDU was set.
* @ampdu_len: number of aggregated frames.
- * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
+ * relevant only if IEEE80211_TX_STAT_AMPDU was set.
* @ack_signal: signal strength of the ACK frame
*/
struct ieee80211_tx_info {
* @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
* @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
* @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
+ * @IEEE80211_CONF_CHANGE_QOS: Quality of service was enabled or disabled
*/
enum ieee80211_conf_changed {
IEEE80211_CONF_CHANGE_SMPS = BIT(1),
* @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
* powersave documentation below. This variable is valid only when
* the CONF_PS flag is set.
+ * @dynamic_ps_forced_timeout: The dynamic powersave timeout (in ms) configured
+ * by cfg80211 (essentially, wext) If set, this value overrules the value
+ * chosen by mac80211 based on ps qos network latency.
*
* @power_level: requested transmit power (in dBm)
*
*/
struct ieee80211_conf {
u32 flags;
- int power_level, dynamic_ps_timeout;
+ int power_level, dynamic_ps_timeout, dynamic_ps_forced_timeout;
int max_sleep_period;
u16 listen_interval;
u8 iv_len;
u8 hw_key_idx;
u8 flags;
+ u8 *ap_addr;
s8 keyidx;
u8 keylen;
u8 key[0];
struct ieee80211_key_conf *conf,
struct ieee80211_sta *sta,
u32 iv32, u16 *phase1key);
- int (*hw_scan)(struct ieee80211_hw *hw,
+ int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
struct cfg80211_scan_request *req);
void (*sw_scan_start)(struct ieee80211_hw *hw);
void (*sw_scan_complete)(struct ieee80211_hw *hw);
struct ieee80211_vif *vif,
enum ieee80211_ampdu_mlme_action action,
struct ieee80211_sta *sta, u16 tid, u16 *ssn);
-
+ int (*get_survey)(struct ieee80211_hw *hw, int idx,
+ struct survey_info *survey);
void (*rfkill_poll)(struct ieee80211_hw *hw);
void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class);
#ifdef CONFIG_NL80211_TESTMODE