#ifndef __NET_CFG80211_H
#define __NET_CFG80211_H
+/*
+ * 802.11 device and configuration interface
+ *
+ * Copyright 2006-2009 Johannes Berg <johannes@sipsolutions.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/netdevice.h>
+#include <linux/debugfs.h>
+#include <linux/list.h>
#include <linux/netlink.h>
#include <linux/skbuff.h>
#include <linux/nl80211.h>
-#include <net/genetlink.h>
+#include <linux/if_ether.h>
+#include <linux/ieee80211.h>
+#include <net/regulatory.h>
+
/* remove once we remove the wext stuff */
#include <net/iw_handler.h>
+#include <linux/wireless.h>
+
/*
- * 802.11 configuration in-kernel interface
+ * wireless hardware capability structures
+ */
+
+/**
+ * enum ieee80211_band - supported frequency bands
*
- * Copyright 2006, 2007 Johannes Berg <johannes@sipsolutions.net>
+ * The bands are assigned this way because the supported
+ * bitrates differ in these bands.
+ *
+ * @IEEE80211_BAND_2GHZ: 2.4GHz ISM band
+ * @IEEE80211_BAND_5GHZ: around 5GHz band (4.9-5.7)
*/
+enum ieee80211_band {
+ IEEE80211_BAND_2GHZ,
+ IEEE80211_BAND_5GHZ,
+
+ /* keep last */
+ IEEE80211_NUM_BANDS
+};
/**
- * struct vif_params - describes virtual interface parameters
- * @mesh_id: mesh ID to use
- * @mesh_id_len: length of the mesh ID
+ * enum ieee80211_channel_flags - channel flags
+ *
+ * Channel flags set by the regulatory control code.
+ *
+ * @IEEE80211_CHAN_DISABLED: This channel is disabled.
+ * @IEEE80211_CHAN_PASSIVE_SCAN: Only passive scanning is permitted
+ * on this channel.
+ * @IEEE80211_CHAN_NO_IBSS: IBSS is not allowed on this channel.
+ * @IEEE80211_CHAN_RADAR: Radar detection is required on this channel.
+ * @IEEE80211_CHAN_NO_FAT_ABOVE: extension channel above this channel
+ * is not permitted.
+ * @IEEE80211_CHAN_NO_FAT_BELOW: extension channel below this channel
+ * is not permitted.
*/
-struct vif_params {
- u8 *mesh_id;
- int mesh_id_len;
+enum ieee80211_channel_flags {
+ IEEE80211_CHAN_DISABLED = 1<<0,
+ IEEE80211_CHAN_PASSIVE_SCAN = 1<<1,
+ IEEE80211_CHAN_NO_IBSS = 1<<2,
+ IEEE80211_CHAN_RADAR = 1<<3,
+ IEEE80211_CHAN_NO_FAT_ABOVE = 1<<4,
+ IEEE80211_CHAN_NO_FAT_BELOW = 1<<5,
};
-/* Radiotap header iteration
- * implemented in net/wireless/radiotap.c
- * docs in Documentation/networking/radiotap-headers.txt
+/**
+ * struct ieee80211_channel - channel definition
+ *
+ * This structure describes a single channel for use
+ * with cfg80211.
+ *
+ * @center_freq: center frequency in MHz
+ * @max_bandwidth: maximum allowed bandwidth for this channel, in MHz
+ * @hw_value: hardware-specific value for the channel
+ * @flags: channel flags from &enum ieee80211_channel_flags.
+ * @orig_flags: channel flags at registration time, used by regulatory
+ * code to support devices with additional restrictions
+ * @band: band this channel belongs to.
+ * @max_antenna_gain: maximum antenna gain in dBi
+ * @max_power: maximum transmission power (in dBm)
+ * @beacon_found: helper to regulatory code to indicate when a beacon
+ * has been found on this channel. Use regulatory_hint_found_beacon()
+ * to enable this, this is is useful only on 5 GHz band.
+ * @orig_mag: internal use
+ * @orig_mpwr: internal use
*/
+struct ieee80211_channel {
+ enum ieee80211_band band;
+ u16 center_freq;
+ u8 max_bandwidth;
+ u16 hw_value;
+ u32 flags;
+ int max_antenna_gain;
+ int max_power;
+ bool beacon_found;
+ u32 orig_flags;
+ int orig_mag, orig_mpwr;
+};
+
/**
- * struct ieee80211_radiotap_iterator - tracks walk thru present radiotap args
- * @rtheader: pointer to the radiotap header we are walking through
- * @max_length: length of radiotap header in cpu byte ordering
- * @this_arg_index: IEEE80211_RADIOTAP_... index of current arg
- * @this_arg: pointer to current radiotap arg
- * @arg_index: internal next argument index
- * @arg: internal next argument pointer
- * @next_bitmap: internal pointer to next present u32
- * @bitmap_shifter: internal shifter for curr u32 bitmap, b0 set == arg present
+ * enum ieee80211_rate_flags - rate flags
+ *
+ * Hardware/specification flags for rates. These are structured
+ * in a way that allows using the same bitrate structure for
+ * different bands/PHY modes.
+ *
+ * @IEEE80211_RATE_SHORT_PREAMBLE: Hardware can send with short
+ * preamble on this bitrate; only relevant in 2.4GHz band and
+ * with CCK rates.
+ * @IEEE80211_RATE_MANDATORY_A: This bitrate is a mandatory rate
+ * when used with 802.11a (on the 5 GHz band); filled by the
+ * core code when registering the wiphy.
+ * @IEEE80211_RATE_MANDATORY_B: This bitrate is a mandatory rate
+ * when used with 802.11b (on the 2.4 GHz band); filled by the
+ * core code when registering the wiphy.
+ * @IEEE80211_RATE_MANDATORY_G: This bitrate is a mandatory rate
+ * when used with 802.11g (on the 2.4 GHz band); filled by the
+ * core code when registering the wiphy.
+ * @IEEE80211_RATE_ERP_G: This is an ERP rate in 802.11g mode.
*/
+enum ieee80211_rate_flags {
+ IEEE80211_RATE_SHORT_PREAMBLE = 1<<0,
+ IEEE80211_RATE_MANDATORY_A = 1<<1,
+ IEEE80211_RATE_MANDATORY_B = 1<<2,
+ IEEE80211_RATE_MANDATORY_G = 1<<3,
+ IEEE80211_RATE_ERP_G = 1<<4,
+};
-struct ieee80211_radiotap_iterator {
- struct ieee80211_radiotap_header *rtheader;
- int max_length;
- int this_arg_index;
- u8 *this_arg;
+/**
+ * struct ieee80211_rate - bitrate definition
+ *
+ * This structure describes a bitrate that an 802.11 PHY can
+ * operate with. The two values @hw_value and @hw_value_short
+ * are only for driver use when pointers to this structure are
+ * passed around.
+ *
+ * @flags: rate-specific flags
+ * @bitrate: bitrate in units of 100 Kbps
+ * @hw_value: driver/hardware value for this rate
+ * @hw_value_short: driver/hardware value for this rate when
+ * short preamble is used
+ */
+struct ieee80211_rate {
+ u32 flags;
+ u16 bitrate;
+ u16 hw_value, hw_value_short;
+};
- int arg_index;
- u8 *arg;
- __le32 *next_bitmap;
- u32 bitmap_shifter;
+/**
+ * struct ieee80211_sta_ht_cap - STA's HT capabilities
+ *
+ * This structure describes most essential parameters needed
+ * to describe 802.11n HT capabilities for an STA.
+ *
+ * @ht_supported: is HT supported by the STA
+ * @cap: HT capabilities map as described in 802.11n spec
+ * @ampdu_factor: Maximum A-MPDU length factor
+ * @ampdu_density: Minimum A-MPDU spacing
+ * @mcs: Supported MCS rates
+ */
+struct ieee80211_sta_ht_cap {
+ u16 cap; /* use IEEE80211_HT_CAP_ */
+ bool ht_supported;
+ u8 ampdu_factor;
+ u8 ampdu_density;
+ struct ieee80211_mcs_info mcs;
};
-extern int ieee80211_radiotap_iterator_init(
- struct ieee80211_radiotap_iterator *iterator,
- struct ieee80211_radiotap_header *radiotap_header,
- int max_length);
+/**
+ * struct ieee80211_supported_band - frequency band definition
+ *
+ * This structure describes a frequency band a wiphy
+ * is able to operate in.
+ *
+ * @channels: Array of channels the hardware can operate in
+ * in this band.
+ * @band: the band this structure represents
+ * @n_channels: Number of channels in @channels
+ * @bitrates: Array of bitrates the hardware can operate with
+ * in this band. Must be sorted to give a valid "supported
+ * rates" IE, i.e. CCK rates first, then OFDM.
+ * @n_bitrates: Number of bitrates in @bitrates
+ */
+struct ieee80211_supported_band {
+ struct ieee80211_channel *channels;
+ struct ieee80211_rate *bitrates;
+ enum ieee80211_band band;
+ int n_channels;
+ int n_bitrates;
+ struct ieee80211_sta_ht_cap ht_cap;
+};
-extern int ieee80211_radiotap_iterator_next(
- struct ieee80211_radiotap_iterator *iterator);
+/*
+ * Wireless hardware/device configuration structures and methods
+ */
+/**
+ * struct vif_params - describes virtual interface parameters
+ * @mesh_id: mesh ID to use
+ * @mesh_id_len: length of the mesh ID
+ */
+struct vif_params {
+ u8 *mesh_id;
+ int mesh_id_len;
+};
- /**
+/**
* struct key_params - key information
*
* Information about a key
* @STATION_FLAG_SHORT_PREAMBLE: station is capable of receiving frames
* with short preambles
* @STATION_FLAG_WME: station is WME/QoS capable
+ * @STATION_FLAG_MFP: station uses management frame protection
*/
enum station_flags {
STATION_FLAG_CHANGED = 1<<0,
STATION_FLAG_AUTHORIZED = 1<<NL80211_STA_FLAG_AUTHORIZED,
STATION_FLAG_SHORT_PREAMBLE = 1<<NL80211_STA_FLAG_SHORT_PREAMBLE,
STATION_FLAG_WME = 1<<NL80211_STA_FLAG_WME,
+ STATION_FLAG_MFP = 1<<NL80211_STA_FLAG_MFP,
};
/**
* @STATION_INFO_SIGNAL: @signal filled
* @STATION_INFO_TX_BITRATE: @tx_bitrate fields are filled
* (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
+ * @STATION_INFO_RX_PACKETS: @rx_packets filled
+ * @STATION_INFO_TX_PACKETS: @tx_packets filled
*/
enum station_info_flags {
STATION_INFO_INACTIVE_TIME = 1<<0,
STATION_INFO_PLINK_STATE = 1<<5,
STATION_INFO_SIGNAL = 1<<6,
STATION_INFO_TX_BITRATE = 1<<7,
+ STATION_INFO_RX_PACKETS = 1<<8,
+ STATION_INFO_TX_PACKETS = 1<<9,
};
/**
* @plink_state: mesh peer link state
* @signal: signal strength of last received packet in dBm
* @txrate: current unicast bitrate to this station
+ * @rx_packets: packets received from this station
+ * @tx_packets: packets transmitted to this station
*/
struct station_info {
u32 filled;
u8 plink_state;
s8 signal;
struct rate_info txrate;
+ u32 rx_packets;
+ u32 tx_packets;
};
/**
u8 basic_rates_len;
};
-/**
- * enum reg_set_by - Indicates who is trying to set the regulatory domain
- * @REGDOM_SET_BY_INIT: regulatory domain was set by initialization. We will be
- * using a static world regulatory domain by default.
- * @REGDOM_SET_BY_CORE: Core queried CRDA for a dynamic world regulatory domain.
- * @REGDOM_SET_BY_USER: User asked the wireless core to set the
- * regulatory domain.
- * @REGDOM_SET_BY_DRIVER: a wireless drivers has hinted to the wireless core
- * it thinks its knows the regulatory domain we should be in.
- * @REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an 802.11 country
- * information element with regulatory information it thinks we
- * should consider.
- */
-enum reg_set_by {
- REGDOM_SET_BY_INIT,
- REGDOM_SET_BY_CORE,
- REGDOM_SET_BY_USER,
- REGDOM_SET_BY_DRIVER,
- REGDOM_SET_BY_COUNTRY_IE,
-};
-
-struct ieee80211_freq_range {
- u32 start_freq_khz;
- u32 end_freq_khz;
- u32 max_bandwidth_khz;
-};
-
-struct ieee80211_power_rule {
- u32 max_antenna_gain;
- u32 max_eirp;
-};
-
-struct ieee80211_reg_rule {
- struct ieee80211_freq_range freq_range;
- struct ieee80211_power_rule power_rule;
- u32 flags;
-};
-
-struct ieee80211_regdomain {
- u32 n_reg_rules;
- char alpha2[2];
- struct ieee80211_reg_rule reg_rules[];
-};
-
-#define MHZ_TO_KHZ(freq) ((freq) * 1000)
-#define KHZ_TO_MHZ(freq) ((freq) / 1000)
-#define DBI_TO_MBI(gain) ((gain) * 100)
-#define MBI_TO_DBI(gain) ((gain) / 100)
-#define DBM_TO_MBM(gain) ((gain) * 100)
-#define MBM_TO_DBM(gain) ((gain) / 100)
-
-#define REG_RULE(start, end, bw, gain, eirp, reg_flags) { \
- .freq_range.start_freq_khz = MHZ_TO_KHZ(start), \
- .freq_range.end_freq_khz = MHZ_TO_KHZ(end), \
- .freq_range.max_bandwidth_khz = MHZ_TO_KHZ(bw), \
- .power_rule.max_antenna_gain = DBI_TO_MBI(gain), \
- .power_rule.max_eirp = DBM_TO_MBM(eirp), \
- .flags = reg_flags, \
- }
-
struct mesh_config {
/* Timeouts in ms */
/* Mesh plink management parameters */
struct ieee80211_channel;
/**
+ * struct cfg80211_ssid - SSID description
+ * @ssid: the SSID
+ * @ssid_len: length of the ssid
+ */
+struct cfg80211_ssid {
+ u8 ssid[IEEE80211_MAX_SSID_LEN];
+ u8 ssid_len;
+};
+
+/**
+ * struct cfg80211_scan_request - scan request description
+ *
+ * @ssids: SSIDs to scan for (active scan only)
+ * @n_ssids: number of SSIDs
+ * @channels: channels to scan on.
+ * @n_channels: number of channels for each band
+ * @ie: optional information element(s) to add into Probe Request or %NULL
+ * @ie_len: length of ie in octets
+ * @wiphy: the wiphy this was for
+ * @ifidx: the interface index
+ */
+struct cfg80211_scan_request {
+ struct cfg80211_ssid *ssids;
+ int n_ssids;
+ struct ieee80211_channel **channels;
+ u32 n_channels;
+ const u8 *ie;
+ size_t ie_len;
+
+ /* internal */
+ struct wiphy *wiphy;
+ int ifidx;
+};
+
+/**
+ * enum cfg80211_signal_type - signal type
+ *
+ * @CFG80211_SIGNAL_TYPE_NONE: no signal strength information available
+ * @CFG80211_SIGNAL_TYPE_MBM: signal strength in mBm (100*dBm)
+ * @CFG80211_SIGNAL_TYPE_UNSPEC: signal strength, increasing from 0 through 100
+ */
+enum cfg80211_signal_type {
+ CFG80211_SIGNAL_TYPE_NONE,
+ CFG80211_SIGNAL_TYPE_MBM,
+ CFG80211_SIGNAL_TYPE_UNSPEC,
+};
+
+/**
+ * struct cfg80211_bss - BSS description
+ *
+ * This structure describes a BSS (which may also be a mesh network)
+ * for use in scan results and similar.
+ *
+ * @bssid: BSSID of the BSS
+ * @tsf: timestamp of last received update
+ * @beacon_interval: the beacon interval as from the frame
+ * @capability: the capability field in host byte order
+ * @information_elements: the information elements (Note that there
+ * is no guarantee that these are well-formed!)
+ * @len_information_elements: total length of the information elements
+ * @signal: signal strength value (type depends on the wiphy's signal_type)
+ * @hold: BSS should not expire
+ * @free_priv: function pointer to free private data
+ * @priv: private area for driver use, has at least wiphy->bss_priv_size bytes
+ */
+struct cfg80211_bss {
+ struct ieee80211_channel *channel;
+
+ u8 bssid[ETH_ALEN];
+ u64 tsf;
+ u16 beacon_interval;
+ u16 capability;
+ u8 *information_elements;
+ size_t len_information_elements;
+
+ s32 signal;
+
+ void (*free_priv)(struct cfg80211_bss *bss);
+ u8 priv[0] __attribute__((__aligned__(sizeof(void *))));
+};
+
+/**
+ * struct cfg80211_auth_request - Authentication request data
+ *
+ * This structure provides information needed to complete IEEE 802.11
+ * authentication.
+ * NOTE: This structure will likely change when more code from mac80211 is
+ * moved into cfg80211 so that non-mac80211 drivers can benefit from it, too.
+ * Before using this in a driver that does not use mac80211, it would be better
+ * to check the status of that work and better yet, volunteer to work on it.
+ *
+ * @chan: The channel to use or %NULL if not specified (auto-select based on
+ * scan results)
+ * @peer_addr: The address of the peer STA (AP BSSID in infrastructure case);
+ * this field is required to be present; if the driver wants to help with
+ * BSS selection, it should use (yet to be added) MLME event to allow user
+ * space SME to be notified of roaming candidate, so that the SME can then
+ * use the authentication request with the recommended BSSID and whatever
+ * other data may be needed for authentication/association
+ * @ssid: SSID or %NULL if not yet available
+ * @ssid_len: Length of ssid in octets
+ * @auth_type: Authentication type (algorithm)
+ * @ie: Extra IEs to add to Authentication frame or %NULL
+ * @ie_len: Length of ie buffer in octets
+ */
+struct cfg80211_auth_request {
+ struct ieee80211_channel *chan;
+ u8 *peer_addr;
+ const u8 *ssid;
+ size_t ssid_len;
+ enum nl80211_auth_type auth_type;
+ const u8 *ie;
+ size_t ie_len;
+};
+
+/**
+ * struct cfg80211_assoc_request - (Re)Association request data
+ *
+ * This structure provides information needed to complete IEEE 802.11
+ * (re)association.
+ * NOTE: This structure will likely change when more code from mac80211 is
+ * moved into cfg80211 so that non-mac80211 drivers can benefit from it, too.
+ * Before using this in a driver that does not use mac80211, it would be better
+ * to check the status of that work and better yet, volunteer to work on it.
+ *
+ * @chan: The channel to use or %NULL if not specified (auto-select based on
+ * scan results)
+ * @peer_addr: The address of the peer STA (AP BSSID); this field is required
+ * to be present and the STA must be in State 2 (authenticated) with the
+ * peer STA
+ * @ssid: SSID
+ * @ssid_len: Length of ssid in octets
+ * @ie: Extra IEs to add to (Re)Association Request frame or %NULL
+ * @ie_len: Length of ie buffer in octets
+ * @use_mfp: Use management frame protection (IEEE 802.11w) in this association
+ */
+struct cfg80211_assoc_request {
+ struct ieee80211_channel *chan;
+ u8 *peer_addr;
+ const u8 *ssid;
+ size_t ssid_len;
+ const u8 *ie;
+ size_t ie_len;
+ bool use_mfp;
+};
+
+/**
+ * struct cfg80211_deauth_request - Deauthentication request data
+ *
+ * This structure provides information needed to complete IEEE 802.11
+ * deauthentication.
+ *
+ * @peer_addr: The address of the peer STA (AP BSSID); this field is required
+ * to be present and the STA must be authenticated with the peer STA
+ * @ie: Extra IEs to add to Deauthentication frame or %NULL
+ * @ie_len: Length of ie buffer in octets
+ */
+struct cfg80211_deauth_request {
+ u8 *peer_addr;
+ u16 reason_code;
+ const u8 *ie;
+ size_t ie_len;
+};
+
+/**
+ * struct cfg80211_disassoc_request - Disassociation request data
+ *
+ * This structure provides information needed to complete IEEE 802.11
+ * disassocation.
+ *
+ * @peer_addr: The address of the peer STA (AP BSSID); this field is required
+ * to be present and the STA must be associated with the peer STA
+ * @ie: Extra IEs to add to Disassociation frame or %NULL
+ * @ie_len: Length of ie buffer in octets
+ */
+struct cfg80211_disassoc_request {
+ u8 *peer_addr;
+ u16 reason_code;
+ const u8 *ie;
+ size_t ie_len;
+};
+
+/**
+ * struct cfg80211_ibss_params - IBSS parameters
+ *
+ * This structure defines the IBSS parameters for the join_ibss()
+ * method.
+ *
+ * @ssid: The SSID, will always be non-null.
+ * @ssid_len: The length of the SSID, will always be non-zero.
+ * @bssid: Fixed BSSID requested, maybe be %NULL, if set do not
+ * search for IBSSs with a different BSSID.
+ * @channel: The channel to use if no IBSS can be found to join.
+ * @channel_fixed: The channel should be fixed -- do not search for
+ * IBSSs to join on other channels.
+ * @ie: information element(s) to include in the beacon
+ * @ie_len: length of that
+ * @beacon_interval: beacon interval to use
+ */
+struct cfg80211_ibss_params {
+ u8 *ssid;
+ u8 *bssid;
+ struct ieee80211_channel *channel;
+ u8 *ie;
+ u8 ssid_len, ie_len;
+ u16 beacon_interval;
+ bool channel_fixed;
+};
+
+/**
+ * enum wiphy_params_flags - set_wiphy_params bitfield values
+ * WIPHY_PARAM_RETRY_SHORT: wiphy->retry_short has changed
+ * WIPHY_PARAM_RETRY_LONG: wiphy->retry_long has changed
+ * WIPHY_PARAM_FRAG_THRESHOLD: wiphy->frag_threshold has changed
+ * WIPHY_PARAM_RTS_THRESHOLD: wiphy->rts_threshold has changed
+ */
+enum wiphy_params_flags {
+ WIPHY_PARAM_RETRY_SHORT = 1 << 0,
+ WIPHY_PARAM_RETRY_LONG = 1 << 1,
+ WIPHY_PARAM_FRAG_THRESHOLD = 1 << 2,
+ WIPHY_PARAM_RTS_THRESHOLD = 1 << 3,
+};
+
+/**
* struct cfg80211_ops - backend description for wireless configuration
*
* This struct is registered by fullmac card drivers and/or wireless stacks
* wireless extensions but this is subject to reevaluation as soon as this
* code is used more widely and we have a first user without wext.
*
+ * @suspend: wiphy device needs to be suspended
+ * @resume: wiphy device needs to be resumed
+ *
* @add_virtual_intf: create a new virtual interface with the given name,
* must set the struct wireless_dev's iftype.
*
*
* @set_default_key: set the default key on an interface
*
+ * @set_default_mgmt_key: set the default management frame key on an interface
+ *
* @add_beacon: Add a beacon with given parameters, @head, @interval
* and @dtim_period will be valid, @tail is optional.
* @set_beacon: Change the beacon parameters for an access point mode
* @set_txq_params: Set TX queue parameters
*
* @set_channel: Set channel
+ *
+ * @scan: Request to do a scan. If returning zero, the scan request is given
+ * the driver, and will be valid until passed to cfg80211_scan_done().
+ * For scan results, call cfg80211_inform_bss(); you can call this outside
+ * the scan/scan_done bracket too.
+ *
+ * @auth: Request to authenticate with the specified peer
+ * @assoc: Request to (re)associate with the specified peer
+ * @deauth: Request to deauthenticate from the specified peer
+ * @disassoc: Request to disassociate from the specified peer
+ *
+ * @join_ibss: Join the specified IBSS (or create if necessary). Once done, call
+ * cfg80211_ibss_joined(), also call that function when changing BSSID due
+ * to a merge.
+ * @leave_ibss: Leave the IBSS.
+ *
+ * @set_wiphy_params: Notify that wiphy parameters have changed;
+ * @changed bitfield (see &enum wiphy_params_flags) describes which values
+ * have changed. The actual parameter values are available in
+ * struct wiphy. If returning an error, no value should be changed.
*/
struct cfg80211_ops {
+ int (*suspend)(struct wiphy *wiphy);
+ int (*resume)(struct wiphy *wiphy);
+
int (*add_virtual_intf)(struct wiphy *wiphy, char *name,
enum nl80211_iftype type, u32 *flags,
struct vif_params *params);
struct vif_params *params);
int (*add_key)(struct wiphy *wiphy, struct net_device *netdev,
- u8 key_index, u8 *mac_addr,
+ u8 key_index, const u8 *mac_addr,
struct key_params *params);
int (*get_key)(struct wiphy *wiphy, struct net_device *netdev,
- u8 key_index, u8 *mac_addr, void *cookie,
+ u8 key_index, const u8 *mac_addr, void *cookie,
void (*callback)(void *cookie, struct key_params*));
int (*del_key)(struct wiphy *wiphy, struct net_device *netdev,
- u8 key_index, u8 *mac_addr);
+ u8 key_index, const u8 *mac_addr);
int (*set_default_key)(struct wiphy *wiphy,
struct net_device *netdev,
u8 key_index);
+ int (*set_default_mgmt_key)(struct wiphy *wiphy,
+ struct net_device *netdev,
+ u8 key_index);
int (*add_beacon)(struct wiphy *wiphy, struct net_device *dev,
struct beacon_parameters *info);
int (*set_channel)(struct wiphy *wiphy,
struct ieee80211_channel *chan,
enum nl80211_channel_type channel_type);
+
+ int (*scan)(struct wiphy *wiphy, struct net_device *dev,
+ struct cfg80211_scan_request *request);
+
+ int (*auth)(struct wiphy *wiphy, struct net_device *dev,
+ struct cfg80211_auth_request *req);
+ int (*assoc)(struct wiphy *wiphy, struct net_device *dev,
+ struct cfg80211_assoc_request *req);
+ int (*deauth)(struct wiphy *wiphy, struct net_device *dev,
+ struct cfg80211_deauth_request *req);
+ int (*disassoc)(struct wiphy *wiphy, struct net_device *dev,
+ struct cfg80211_disassoc_request *req);
+
+ int (*join_ibss)(struct wiphy *wiphy, struct net_device *dev,
+ struct cfg80211_ibss_params *params);
+ int (*leave_ibss)(struct wiphy *wiphy, struct net_device *dev);
+
+ int (*set_wiphy_params)(struct wiphy *wiphy, u32 changed);
};
-/* temporary wext handlers */
+/*
+ * wireless hardware and networking interfaces structures
+ * and registration/helper functions
+ */
+
+/**
+ * struct wiphy - wireless hardware description
+ * @idx: the wiphy index assigned to this item
+ * @class_dev: the class device representing /sys/class/ieee80211/<wiphy-name>
+ * @custom_regulatory: tells us the driver for this device
+ * has its own custom regulatory domain and cannot identify the
+ * ISO / IEC 3166 alpha2 it belongs to. When this is enabled
+ * we will disregard the first regulatory hint (when the
+ * initiator is %REGDOM_SET_BY_CORE).
+ * @strict_regulatory: tells us the driver for this device will ignore
+ * regulatory domain settings until it gets its own regulatory domain
+ * via its regulatory_hint(). After its gets its own regulatory domain
+ * it will only allow further regulatory domain settings to further
+ * enhance compliance. For example if channel 13 and 14 are disabled
+ * by this regulatory domain no user regulatory domain can enable these
+ * channels at a later time. This can be used for devices which do not
+ * have calibration information gauranteed for frequencies or settings
+ * outside of its regulatory domain.
+ * @reg_notifier: the driver's regulatory notification callback
+ * @regd: the driver's regulatory domain, if one was requested via
+ * the regulatory_hint() API. This can be used by the driver
+ * on the reg_notifier() if it chooses to ignore future
+ * regulatory domain changes caused by other drivers.
+ * @signal_type: signal type reported in &struct cfg80211_bss.
+ * @cipher_suites: supported cipher suites
+ * @n_cipher_suites: number of supported cipher suites
+ * @retry_short: Retry limit for short frames (dot11ShortRetryLimit)
+ * @retry_long: Retry limit for long frames (dot11LongRetryLimit)
+ * @frag_threshold: Fragmentation threshold (dot11FragmentationThreshold);
+ * -1 = fragmentation disabled, only odd values >= 256 used
+ * @rts_threshold: RTS threshold (dot11RTSThreshold); -1 = RTS/CTS disabled
+ */
+struct wiphy {
+ /* assign these fields before you register the wiphy */
+
+ /* permanent MAC address */
+ u8 perm_addr[ETH_ALEN];
+
+ /* Supported interface modes, OR together BIT(NL80211_IFTYPE_...) */
+ u16 interface_modes;
+
+ bool custom_regulatory;
+ bool strict_regulatory;
+
+ enum cfg80211_signal_type signal_type;
+
+ int bss_priv_size;
+ u8 max_scan_ssids;
+ u16 max_scan_ie_len;
+
+ int n_cipher_suites;
+ const u32 *cipher_suites;
+
+ u8 retry_short;
+ u8 retry_long;
+ u32 frag_threshold;
+ u32 rts_threshold;
+
+ /* If multiple wiphys are registered and you're handed e.g.
+ * a regular netdev with assigned ieee80211_ptr, you won't
+ * know whether it points to a wiphy your driver has registered
+ * or not. Assign this to something global to your driver to
+ * help determine whether you own this wiphy or not. */
+ void *privid;
+
+ struct ieee80211_supported_band *bands[IEEE80211_NUM_BANDS];
+
+ /* Lets us get back the wiphy on the callback */
+ int (*reg_notifier)(struct wiphy *wiphy,
+ struct regulatory_request *request);
+
+ /* fields below are read-only, assigned by cfg80211 */
+
+ const struct ieee80211_regdomain *regd;
+
+ /* the item in /sys/class/ieee80211/ points to this,
+ * you need use set_wiphy_dev() (see below) */
+ struct device dev;
+
+ /* dir in debugfs: ieee80211/<wiphyname> */
+ struct dentry *debugfsdir;
+
+ char priv[0] __attribute__((__aligned__(NETDEV_ALIGN)));
+};
+
+/**
+ * wiphy_priv - return priv from wiphy
+ *
+ * @wiphy: the wiphy whose priv pointer to return
+ */
+static inline void *wiphy_priv(struct wiphy *wiphy)
+{
+ BUG_ON(!wiphy);
+ return &wiphy->priv;
+}
+
+/**
+ * set_wiphy_dev - set device pointer for wiphy
+ *
+ * @wiphy: The wiphy whose device to bind
+ * @dev: The device to parent it to
+ */
+static inline void set_wiphy_dev(struct wiphy *wiphy, struct device *dev)
+{
+ wiphy->dev.parent = dev;
+}
+
+/**
+ * wiphy_dev - get wiphy dev pointer
+ *
+ * @wiphy: The wiphy whose device struct to look up
+ */
+static inline struct device *wiphy_dev(struct wiphy *wiphy)
+{
+ return wiphy->dev.parent;
+}
+
+/**
+ * wiphy_name - get wiphy name
+ *
+ * @wiphy: The wiphy whose name to return
+ */
+static inline const char *wiphy_name(struct wiphy *wiphy)
+{
+ return dev_name(&wiphy->dev);
+}
+
+/**
+ * wiphy_new - create a new wiphy for use with cfg80211
+ *
+ * @ops: The configuration operations for this device
+ * @sizeof_priv: The size of the private area to allocate
+ *
+ * Create a new wiphy and associate the given operations with it.
+ * @sizeof_priv bytes are allocated for private use.
+ *
+ * The returned pointer must be assigned to each netdev's
+ * ieee80211_ptr for proper operation.
+ */
+struct wiphy *wiphy_new(struct cfg80211_ops *ops, int sizeof_priv);
+
+/**
+ * wiphy_register - register a wiphy with cfg80211
+ *
+ * @wiphy: The wiphy to register.
+ *
+ * Returns a non-negative wiphy index or a negative error code.
+ */
+extern int wiphy_register(struct wiphy *wiphy);
+
+/**
+ * wiphy_unregister - deregister a wiphy from cfg80211
+ *
+ * @wiphy: The wiphy to unregister.
+ *
+ * After this call, no more requests can be made with this priv
+ * pointer, but the call may sleep to wait for an outstanding
+ * request that is being handled.
+ */
+extern void wiphy_unregister(struct wiphy *wiphy);
+
+/**
+ * wiphy_free - free wiphy
+ *
+ * @wiphy: The wiphy to free
+ */
+extern void wiphy_free(struct wiphy *wiphy);
+
+/**
+ * struct wireless_dev - wireless per-netdev state
+ *
+ * This structure must be allocated by the driver/stack
+ * that uses the ieee80211_ptr field in struct net_device
+ * (this is intentional so it can be allocated along with
+ * the netdev.)
+ *
+ * @wiphy: pointer to hardware description
+ * @iftype: interface type
+ * @list: (private) Used to collect the interfaces
+ * @netdev: (private) Used to reference back to the netdev
+ * @current_bss: (private) Used by the internal configuration code
+ * @bssid: (private) Used by the internal configuration code
+ * @ssid: (private) Used by the internal configuration code
+ * @ssid_len: (private) Used by the internal configuration code
+ * @wext: (private) Used by the internal wireless extensions compat code
+ * @wext_bssid: (private) Used by the internal wireless extensions compat code
+ */
+struct wireless_dev {
+ struct wiphy *wiphy;
+ enum nl80211_iftype iftype;
+
+ /* private to the generic wireless code */
+ struct list_head list;
+ struct net_device *netdev;
+
+ /* currently used for IBSS - might be rearranged in the future */
+ struct cfg80211_bss *current_bss;
+ u8 bssid[ETH_ALEN];
+ u8 ssid[IEEE80211_MAX_SSID_LEN];
+ u8 ssid_len;
+
+#ifdef CONFIG_WIRELESS_EXT
+ /* wext data */
+ struct {
+ struct cfg80211_ibss_params ibss;
+ u8 bssid[ETH_ALEN];
+ s8 default_key, default_mgmt_key;
+ } wext;
+#endif
+};
+
+/**
+ * wdev_priv - return wiphy priv from wireless_dev
+ *
+ * @wdev: The wireless device whose wiphy's priv pointer to return
+ */
+static inline void *wdev_priv(struct wireless_dev *wdev)
+{
+ BUG_ON(!wdev);
+ return wiphy_priv(wdev->wiphy);
+}
+
+/*
+ * Utility functions
+ */
+
+/**
+ * ieee80211_channel_to_frequency - convert channel number to frequency
+ */
+extern int ieee80211_channel_to_frequency(int chan);
+
+/**
+ * ieee80211_frequency_to_channel - convert frequency to channel number
+ */
+extern int ieee80211_frequency_to_channel(int freq);
+
+/*
+ * Name indirection necessary because the ieee80211 code also has
+ * a function named "ieee80211_get_channel", so if you include
+ * cfg80211's header file you get cfg80211's version, if you try
+ * to include both header files you'll (rightfully!) get a symbol
+ * clash.
+ */
+extern struct ieee80211_channel *__ieee80211_get_channel(struct wiphy *wiphy,
+ int freq);
+/**
+ * ieee80211_get_channel - get channel struct from wiphy for specified frequency
+ */
+static inline struct ieee80211_channel *
+ieee80211_get_channel(struct wiphy *wiphy, int freq)
+{
+ return __ieee80211_get_channel(wiphy, freq);
+}
+
+/**
+ * ieee80211_get_response_rate - get basic rate for a given rate
+ *
+ * @sband: the band to look for rates in
+ * @basic_rates: bitmap of basic rates
+ * @bitrate: the bitrate for which to find the basic rate
+ *
+ * This function returns the basic rate corresponding to a given
+ * bitrate, that is the next lower bitrate contained in the basic
+ * rate map, which is, for this function, given as a bitmap of
+ * indices of rates in the band's bitrate table.
+ */
+struct ieee80211_rate *
+ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
+ u32 basic_rates, int bitrate);
+
+/*
+ * Radiotap parsing functions -- for controlled injection support
+ *
+ * Implemented in net/wireless/radiotap.c
+ * Documentation in Documentation/networking/radiotap-headers.txt
+ */
+
+/**
+ * struct ieee80211_radiotap_iterator - tracks walk thru present radiotap args
+ * @rtheader: pointer to the radiotap header we are walking through
+ * @max_length: length of radiotap header in cpu byte ordering
+ * @this_arg_index: IEEE80211_RADIOTAP_... index of current arg
+ * @this_arg: pointer to current radiotap arg
+ * @arg_index: internal next argument index
+ * @arg: internal next argument pointer
+ * @next_bitmap: internal pointer to next present u32
+ * @bitmap_shifter: internal shifter for curr u32 bitmap, b0 set == arg present
+ */
+
+struct ieee80211_radiotap_iterator {
+ struct ieee80211_radiotap_header *rtheader;
+ int max_length;
+ int this_arg_index;
+ u8 *this_arg;
+
+ int arg_index;
+ u8 *arg;
+ __le32 *next_bitmap;
+ u32 bitmap_shifter;
+};
+
+extern int ieee80211_radiotap_iterator_init(
+ struct ieee80211_radiotap_iterator *iterator,
+ struct ieee80211_radiotap_header *radiotap_header,
+ int max_length);
+
+extern int ieee80211_radiotap_iterator_next(
+ struct ieee80211_radiotap_iterator *iterator);
+
+/*
+ * Regulatory helper functions for wiphys
+ */
+
+/**
+ * regulatory_hint - driver hint to the wireless core a regulatory domain
+ * @wiphy: the wireless device giving the hint (used only for reporting
+ * conflicts)
+ * @alpha2: the ISO/IEC 3166 alpha2 the driver claims its regulatory domain
+ * should be in. If @rd is set this should be NULL. Note that if you
+ * set this to NULL you should still set rd->alpha2 to some accepted
+ * alpha2.
+ *
+ * Wireless drivers can use this function to hint to the wireless core
+ * what it believes should be the current regulatory domain by
+ * giving it an ISO/IEC 3166 alpha2 country code it knows its regulatory
+ * domain should be in or by providing a completely build regulatory domain.
+ * If the driver provides an ISO/IEC 3166 alpha2 userspace will be queried
+ * for a regulatory domain structure for the respective country.
+ *
+ * The wiphy must have been registered to cfg80211 prior to this call.
+ * For cfg80211 drivers this means you must first use wiphy_register(),
+ * for mac80211 drivers you must first use ieee80211_register_hw().
+ *
+ * Drivers should check the return value, its possible you can get
+ * an -ENOMEM.
+ */
+extern int regulatory_hint(struct wiphy *wiphy, const char *alpha2);
+
+/**
+ * regulatory_hint_11d - hints a country IE as a regulatory domain
+ * @wiphy: the wireless device giving the hint (used only for reporting
+ * conflicts)
+ * @country_ie: pointer to the country IE
+ * @country_ie_len: length of the country IE
+ *
+ * We will intersect the rd with the what CRDA tells us should apply
+ * for the alpha2 this country IE belongs to, this prevents APs from
+ * sending us incorrect or outdated information against a country.
+ */
+extern void regulatory_hint_11d(struct wiphy *wiphy,
+ u8 *country_ie,
+ u8 country_ie_len);
+/**
+ * wiphy_apply_custom_regulatory - apply a custom driver regulatory domain
+ * @wiphy: the wireless device we want to process the regulatory domain on
+ * @regd: the custom regulatory domain to use for this wiphy
+ *
+ * Drivers can sometimes have custom regulatory domains which do not apply
+ * to a specific country. Drivers can use this to apply such custom regulatory
+ * domains. This routine must be called prior to wiphy registration. The
+ * custom regulatory domain will be trusted completely and as such previous
+ * default channel settings will be disregarded. If no rule is found for a
+ * channel on the regulatory domain the channel will be disabled.
+ */
+extern void wiphy_apply_custom_regulatory(
+ struct wiphy *wiphy,
+ const struct ieee80211_regdomain *regd);
+
+/**
+ * freq_reg_info - get regulatory information for the given frequency
+ * @wiphy: the wiphy for which we want to process this rule for
+ * @center_freq: Frequency in KHz for which we want regulatory information for
+ * @bandwidth: the bandwidth requirement you have in KHz, if you do not have one
+ * you can set this to 0. If this frequency is allowed we then set
+ * this value to the maximum allowed bandwidth.
+ * @reg_rule: the regulatory rule which we have for this frequency
+ *
+ * Use this function to get the regulatory rule for a specific frequency on
+ * a given wireless device. If the device has a specific regulatory domain
+ * it wants to follow we respect that unless a country IE has been received
+ * and processed already.
+ *
+ * Returns 0 if it was able to find a valid regulatory rule which does
+ * apply to the given center_freq otherwise it returns non-zero. It will
+ * also return -ERANGE if we determine the given center_freq does not even have
+ * a regulatory rule for a frequency range in the center_freq's band. See
+ * freq_in_rule_band() for our current definition of a band -- this is purely
+ * subjective and right now its 802.11 specific.
+ */
+extern int freq_reg_info(struct wiphy *wiphy, u32 center_freq, u32 *bandwidth,
+ const struct ieee80211_reg_rule **reg_rule);
+
+/*
+ * Temporary wext handlers & helper functions
+ *
+ * In the future cfg80211 will simply assign the entire wext handler
+ * structure to netdevs it manages, but we're not there yet.
+ */
int cfg80211_wext_giwname(struct net_device *dev,
struct iw_request_info *info,
char *name, char *extra);
u32 *mode, char *extra);
int cfg80211_wext_giwmode(struct net_device *dev, struct iw_request_info *info,
u32 *mode, char *extra);
+int cfg80211_wext_siwscan(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu, char *extra);
+int cfg80211_wext_giwscan(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_point *data, char *extra);
+int cfg80211_wext_siwmlme(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_point *data, char *extra);
+int cfg80211_wext_giwrange(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_point *data, char *extra);
+int cfg80211_ibss_wext_siwfreq(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_freq *freq, char *extra);
+int cfg80211_ibss_wext_giwfreq(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_freq *freq, char *extra);
+int cfg80211_ibss_wext_siwessid(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_point *data, char *ssid);
+int cfg80211_ibss_wext_giwessid(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_point *data, char *ssid);
+int cfg80211_ibss_wext_siwap(struct net_device *dev,
+ struct iw_request_info *info,
+ struct sockaddr *ap_addr, char *extra);
+int cfg80211_ibss_wext_giwap(struct net_device *dev,
+ struct iw_request_info *info,
+ struct sockaddr *ap_addr, char *extra);
+
+struct ieee80211_channel *cfg80211_wext_freq(struct wiphy *wiphy,
+ struct iw_freq *freq);
+
+int cfg80211_wext_siwrts(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_param *rts, char *extra);
+int cfg80211_wext_giwrts(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_param *rts, char *extra);
+int cfg80211_wext_siwfrag(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_param *frag, char *extra);
+int cfg80211_wext_giwfrag(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_param *frag, char *extra);
+int cfg80211_wext_siwretry(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_param *retry, char *extra);
+int cfg80211_wext_giwretry(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_param *retry, char *extra);
+int cfg80211_wext_siwencodeext(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_point *erq, char *extra);
+int cfg80211_wext_siwencode(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_point *erq, char *keybuf);
+int cfg80211_wext_giwencode(struct net_device *dev,
+ struct iw_request_info *info,
+ struct iw_point *erq, char *keybuf);
+
+/*
+ * callbacks for asynchronous cfg80211 methods, notification
+ * functions and BSS handling helpers
+ */
+
+/**
+ * cfg80211_scan_done - notify that scan finished
+ *
+ * @request: the corresponding scan request
+ * @aborted: set to true if the scan was aborted for any reason,
+ * userspace will be notified of that
+ */
+void cfg80211_scan_done(struct cfg80211_scan_request *request, bool aborted);
+
+/**
+ * cfg80211_inform_bss - inform cfg80211 of a new BSS
+ *
+ * @wiphy: the wiphy reporting the BSS
+ * @bss: the found BSS
+ * @signal: the signal strength, type depends on the wiphy's signal_type
+ * @gfp: context flags
+ *
+ * This informs cfg80211 that BSS information was found and
+ * the BSS should be updated/added.
+ */
+struct cfg80211_bss*
+cfg80211_inform_bss_frame(struct wiphy *wiphy,
+ struct ieee80211_channel *channel,
+ struct ieee80211_mgmt *mgmt, size_t len,
+ s32 signal, gfp_t gfp);
+
+struct cfg80211_bss*
+cfg80211_inform_bss(struct wiphy *wiphy,
+ struct ieee80211_channel *channel,
+ const u8 *bssid,
+ u64 timestamp, u16 capability, u16 beacon_interval,
+ const u8 *ie, size_t ielen,
+ s32 signal, gfp_t gfp);
+
+struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy,
+ struct ieee80211_channel *channel,
+ const u8 *bssid,
+ const u8 *ssid, size_t ssid_len,
+ u16 capa_mask, u16 capa_val);
+static inline struct cfg80211_bss *
+cfg80211_get_ibss(struct wiphy *wiphy,
+ struct ieee80211_channel *channel,
+ const u8 *ssid, size_t ssid_len)
+{
+ return cfg80211_get_bss(wiphy, channel, NULL, ssid, ssid_len,
+ WLAN_CAPABILITY_IBSS, WLAN_CAPABILITY_IBSS);
+}
+
+struct cfg80211_bss *cfg80211_get_mesh(struct wiphy *wiphy,
+ struct ieee80211_channel *channel,
+ const u8 *meshid, size_t meshidlen,
+ const u8 *meshcfg);
+void cfg80211_put_bss(struct cfg80211_bss *bss);
+
+/**
+ * cfg80211_unlink_bss - unlink BSS from internal data structures
+ * @wiphy: the wiphy
+ * @bss: the bss to remove
+ *
+ * This function removes the given BSS from the internal data structures
+ * thereby making it no longer show up in scan results etc. Use this
+ * function when you detect a BSS is gone. Normally BSSes will also time
+ * out, so it is not necessary to use this function at all.
+ */
+void cfg80211_unlink_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
+
+/**
+ * cfg80211_send_rx_auth - notification of processed authentication
+ * @dev: network device
+ * @buf: authentication frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever an authentication has been processed in
+ * station mode. The driver is required to call either this function or
+ * cfg80211_send_auth_timeout() to indicate the result of cfg80211_ops::auth()
+ * call.
+ */
+void cfg80211_send_rx_auth(struct net_device *dev, const u8 *buf, size_t len);
+
+/**
+ * cfg80211_send_auth_timeout - notification of timed out authentication
+ * @dev: network device
+ * @addr: The MAC address of the device with which the authentication timed out
+ */
+void cfg80211_send_auth_timeout(struct net_device *dev, const u8 *addr);
+
+/**
+ * cfg80211_send_rx_assoc - notification of processed association
+ * @dev: network device
+ * @buf: (re)association response frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever a (re)association response has been
+ * processed in station mode. The driver is required to call either this
+ * function or cfg80211_send_assoc_timeout() to indicate the result of
+ * cfg80211_ops::assoc() call.
+ */
+void cfg80211_send_rx_assoc(struct net_device *dev, const u8 *buf, size_t len);
+
+/**
+ * cfg80211_send_assoc_timeout - notification of timed out association
+ * @dev: network device
+ * @addr: The MAC address of the device with which the association timed out
+ */
+void cfg80211_send_assoc_timeout(struct net_device *dev, const u8 *addr);
+
+/**
+ * cfg80211_send_deauth - notification of processed deauthentication
+ * @dev: network device
+ * @buf: deauthentication frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever deauthentication has been processed in
+ * station mode. This includes both received deauthentication frames and
+ * locally generated ones.
+ */
+void cfg80211_send_deauth(struct net_device *dev, const u8 *buf, size_t len);
+
+/**
+ * cfg80211_send_disassoc - notification of processed disassociation
+ * @dev: network device
+ * @buf: disassociation response frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever disassociation has been processed in
+ * station mode. This includes both received disassociation frames and locally
+ * generated ones.
+ */
+void cfg80211_send_disassoc(struct net_device *dev, const u8 *buf, size_t len);
+
+/**
+ * cfg80211_hold_bss - exclude bss from expiration
+ * @bss: bss which should not expire
+ *
+ * In a case when the BSS is not updated but it shouldn't expire this
+ * function can be used to mark the BSS to be excluded from expiration.
+ */
+void cfg80211_hold_bss(struct cfg80211_bss *bss);
+
+/**
+ * cfg80211_unhold_bss - remove expiration exception from the BSS
+ * @bss: bss which can expire again
+ *
+ * This function marks the BSS to be expirable again.
+ */
+void cfg80211_unhold_bss(struct cfg80211_bss *bss);
+
+/**
+ * cfg80211_michael_mic_failure - notification of Michael MIC failure (TKIP)
+ * @dev: network device
+ * @addr: The source MAC address of the frame
+ * @key_type: The key type that the received frame used
+ * @key_id: Key identifier (0..3)
+ * @tsc: The TSC value of the frame that generated the MIC failure (6 octets)
+ *
+ * This function is called whenever the local MAC detects a MIC failure in a
+ * received frame. This matches with MLME-MICHAELMICFAILURE.indication()
+ * primitive.
+ */
+void cfg80211_michael_mic_failure(struct net_device *dev, const u8 *addr,
+ enum nl80211_key_type key_type, int key_id,
+ const u8 *tsc);
+
+/**
+ * cfg80211_ibss_joined - notify cfg80211 that device joined an IBSS
+ *
+ * @dev: network device
+ * @bssid: the BSSID of the IBSS joined
+ * @gfp: allocation flags
+ *
+ * This function notifies cfg80211 that the device joined an IBSS or
+ * switched to a different BSSID. Before this function can be called,
+ * either a beacon has to have been received from the IBSS, or one of
+ * the cfg80211_inform_bss{,_frame} functions must have been called
+ * with the locally generated beacon -- this guarantees that there is
+ * always a scan result for this IBSS. cfg80211 will handle the rest.
+ */
+void cfg80211_ibss_joined(struct net_device *dev, const u8 *bssid, gfp_t gfp);
#endif /* __NET_CFG80211_H */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff