/* ------------------------------------------------------------------------- */
-/* Helper function for I2C legacy drivers */
+/* I2C Helper functions */
struct i2c_driver;
struct i2c_adapter;
struct v4l2_subdev;
struct v4l2_subdev_ops;
-int v4l2_i2c_attach(struct i2c_adapter *adapter, int address, struct i2c_driver *driver,
- const char *name,
- int (*probe)(struct i2c_client *, const struct i2c_device_id *));
/* Load an i2c module and return an initialized v4l2_subdev struct.
Only call request_module if module_name != NULL.
The client_type argument is the name of the chip that's on the adapter. */
-struct v4l2_subdev *v4l2_i2c_new_subdev(struct i2c_adapter *adapter,
+struct v4l2_subdev *v4l2_i2c_new_subdev(struct v4l2_device *v4l2_dev,
+ struct i2c_adapter *adapter,
const char *module_name, const char *client_type, u8 addr);
/* Probe and load an i2c module and return an initialized v4l2_subdev struct.
Only call request_module if module_name != NULL.
The client_type argument is the name of the chip that's on the adapter. */
-struct v4l2_subdev *v4l2_i2c_new_probed_subdev(struct i2c_adapter *adapter,
+struct v4l2_subdev *v4l2_i2c_new_probed_subdev(struct v4l2_device *v4l2_dev,
+ struct i2c_adapter *adapter,
const char *module_name, const char *client_type,
const unsigned short *addrs);
+/* Like v4l2_i2c_new_probed_subdev, except probe for a single address. */
+struct v4l2_subdev *v4l2_i2c_new_probed_subdev_addr(struct v4l2_device *v4l2_dev,
+ struct i2c_adapter *adapter,
+ const char *module_name, const char *client_type, u8 addr);
/* Initialize an v4l2_subdev with data from an i2c_client struct */
void v4l2_i2c_subdev_init(struct v4l2_subdev *sd, struct i2c_client *client,
const struct v4l2_subdev_ops *ops);
/* ------------------------------------------------------------------------- */
-/* Internal ioctls */
-
-/* VIDIOC_INT_DECODE_VBI_LINE */
-struct v4l2_decode_vbi_line {
- u32 is_second_field; /* Set to 0 for the first (odd) field,
- set to 1 for the second (even) field. */
- u8 *p; /* Pointer to the sliced VBI data from the decoder.
- On exit points to the start of the payload. */
- u32 line; /* Line number of the sliced VBI data (1-23) */
- u32 type; /* VBI service type (V4L2_SLICED_*). 0 if no service found */
-};
+/* Note: these remaining ioctls/structs should be removed as well, but they are
+ still used in tuner-simple.c (TUNER_SET_CONFIG), cx18/ivtv (RESET) and
+ v4l2-int-device.h (v4l2_routing). To remove these ioctls some more cleanup
+ is needed in those modules. */
+/* s_config */
struct v4l2_priv_tun_config {
int tuner;
void *priv;
};
-
-/* audio ioctls */
-
-/* v4l device was opened in Radio mode, to be replaced by VIDIOC_INT_S_TUNER_MODE */
-#define AUDC_SET_RADIO _IO('d',88)
-
-/* tuner ioctls */
-
-/* Sets tuner type and its I2C addr */
-#define TUNER_SET_TYPE_ADDR _IOW('d', 90, int)
-
-/* Puts tuner on powersaving state, disabling it, except for i2c. To be replaced
- by VIDIOC_INT_S_STANDBY. */
-#define TUNER_SET_STANDBY _IOW('d', 91, int)
-
-/* Sets tda9887 specific stuff, like port1, port2 and qss */
#define TUNER_SET_CONFIG _IOW('d', 92, struct v4l2_priv_tun_config)
-/* Switch the tuner to a specific tuner mode. Replacement of AUDC_SET_RADIO */
-#define VIDIOC_INT_S_TUNER_MODE _IOW('d', 93, enum v4l2_tuner_type)
-
-/* Generic standby command. Passing -1 (all bits set to 1) will put the whole
- chip into standby mode, value 0 will make the chip fully active. Specific
- bits can be used by certain chips to enable/disable specific subsystems.
- Replacement of TUNER_SET_STANDBY. */
-#define VIDIOC_INT_S_STANDBY _IOW('d', 94, u32)
-
-/* 100, 101 used by VIDIOC_DBG_[SG]_REGISTER */
-
-/* Generic reset command. The argument selects which subsystems to reset.
- Passing 0 will always reset the whole chip. */
#define VIDIOC_INT_RESET _IOW ('d', 102, u32)
-/* Set the frequency (in Hz) of the audio clock output.
- Used to slave an audio processor to the video decoder, ensuring that audio
- and video remain synchronized.
- Usual values for the frequency are 48000, 44100 or 32000 Hz.
- If the frequency is not supported, then -EINVAL is returned. */
-#define VIDIOC_INT_AUDIO_CLOCK_FREQ _IOW ('d', 103, u32)
-
-/* Video decoders that support sliced VBI need to implement this ioctl.
- Field p of the v4l2_sliced_vbi_line struct is set to the start of the VBI
- data that was generated by the decoder. The driver then parses the sliced
- VBI data and sets the other fields in the struct accordingly. The pointer p
- is updated to point to the start of the payload which can be copied
- verbatim into the data field of the v4l2_sliced_vbi_data struct. If no
- valid VBI data was found, then the type field is set to 0 on return. */
-#define VIDIOC_INT_DECODE_VBI_LINE _IOWR('d', 104, struct v4l2_decode_vbi_line)
-
-/* Used to generate VBI signals on a video signal. v4l2_sliced_vbi_data is
- filled with the data packets that should be output. Note that if you set
- the line field to 0, then that VBI signal is disabled. If no
- valid VBI data was found, then the type field is set to 0 on return. */
-#define VIDIOC_INT_S_VBI_DATA _IOW ('d', 105, struct v4l2_sliced_vbi_data)
-
-/* Used to obtain the sliced VBI packet from a readback register. Not all
- video decoders support this. If no data is available because the readback
- register contains invalid or erroneous data -EIO is returned. Note that
- you must fill in the 'id' member and the 'field' member (to determine
- whether CC data from the first or second field should be obtained). */
-#define VIDIOC_INT_G_VBI_DATA _IOWR('d', 106, struct v4l2_sliced_vbi_data)
-
-/* Sets I2S speed in bps. This is used to provide a standard way to select I2S
- clock used by driving digital audio streams at some board designs.
- Usual values for the frequency are 1024000 and 2048000.
- If the frequency is not supported, then -EINVAL is returned. */
-#define VIDIOC_INT_I2S_CLOCK_FREQ _IOW ('d', 108, u32)
-
-/* Routing definition, device dependent. It specifies which inputs (if any)
- should be routed to which outputs (if any). */
struct v4l2_routing {
u32 input;
u32 output;
};
-/* These internal commands should be used to define the inputs and outputs
- of an audio/video chip. They will replace the v4l2 API commands
- VIDIOC_S/G_INPUT, VIDIOC_S/G_OUTPUT, VIDIOC_S/G_AUDIO and VIDIOC_S/G_AUDOUT
- that are meant to be used by the user.
- The internal commands should be used to switch inputs/outputs
- because only the driver knows how to map a 'Television' input to the precise
- input/output routing of an A/D converter, or a DSP, or a video digitizer.
- These four commands should only be sent directly to an i2c device, they
- should not be broadcast as the routing is very device specific. */
-#define VIDIOC_INT_S_AUDIO_ROUTING _IOW ('d', 109, struct v4l2_routing)
-#define VIDIOC_INT_G_AUDIO_ROUTING _IOR ('d', 110, struct v4l2_routing)
-#define VIDIOC_INT_S_VIDEO_ROUTING _IOW ('d', 111, struct v4l2_routing)
-#define VIDIOC_INT_G_VIDEO_ROUTING _IOR ('d', 112, struct v4l2_routing)
-
-struct v4l2_crystal_freq {
- u32 freq; /* frequency in Hz of the crystal */
- u32 flags; /* device specific flags */
-};
-
-/* Sets the frequency of the crystal used to generate the clocks.
- An extra flags field allows device specific configuration regarding
- clock frequency dividers, etc. If not used, then set flags to 0.
- If the frequency is not supported, then -EINVAL is returned. */
-#define VIDIOC_INT_S_CRYSTAL_FREQ _IOW('d', 113, struct v4l2_crystal_freq)
-
-/* Initialize the sensor registors to some sort of reasonable
- default values. */
-#define VIDIOC_INT_INIT _IOW('d', 114, u32)
-
-/* Set v4l2_std_id for video OUTPUT devices. This is ignored by
- video input devices. */
-#define VIDIOC_INT_S_STD_OUTPUT _IOW('d', 115, v4l2_std_id)
-
-/* Get v4l2_std_id for video OUTPUT devices. This is ignored by
- video input devices. */
-#define VIDIOC_INT_G_STD_OUTPUT _IOW('d', 116, v4l2_std_id)
-
-/* Set GPIO pins. Very simple right now, might need to be extended with
- a v4l2_gpio struct if a direction is also needed. */
-#define VIDIOC_INT_S_GPIO _IOW('d', 117, u32)
-
-/* Get input status. Same as the status field in the v4l2_input struct. */
-#define VIDIOC_INT_G_INPUT_STATUS _IOR('d', 118, u32)
-
#endif /* V4L2_COMMON_H_ */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff