#ifndef _LINUX_SERIAL_H
#define _LINUX_SERIAL_H
+#include <linux/types.h>
+
#ifdef __KERNEL__
#include <asm/page.h>
/*
* Definitions for async_struct (and serial_struct) flags field
+ *
+ * Define ASYNCB_* for convenient use with {test,set,clear}_bit.
*/
-#define ASYNC_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes
- on the callout port */
-#define ASYNC_FOURPORT 0x0002 /* Set OU1, OUT2 per AST Fourport settings */
-#define ASYNC_SAK 0x0004 /* Secure Attention Key (Orange book) */
-#define ASYNC_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */
-
-#define ASYNC_SPD_MASK 0x1030
-#define ASYNC_SPD_HI 0x0010 /* Use 56000 instead of 38400 bps */
-
-#define ASYNC_SPD_VHI 0x0020 /* Use 115200 instead of 38400 bps */
-#define ASYNC_SPD_CUST 0x0030 /* Use user-specified divisor */
-
-#define ASYNC_SKIP_TEST 0x0040 /* Skip UART test during autoconfiguration */
-#define ASYNC_AUTO_IRQ 0x0080 /* Do automatic IRQ during autoconfiguration */
-#define ASYNC_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */
-#define ASYNC_PGRP_LOCKOUT 0x0200 /* Lock out cua opens based on pgrp */
-#define ASYNC_CALLOUT_NOHUP 0x0400 /* Don't do hangups for cua device */
-
-#define ASYNC_HARDPPS_CD 0x0800 /* Call hardpps when CD goes high */
-
-#define ASYNC_SPD_SHI 0x1000 /* Use 230400 instead of 38400 bps */
-#define ASYNC_SPD_WARP 0x1010 /* Use 460800 instead of 38400 bps */
-
-#define ASYNC_LOW_LATENCY 0x2000 /* Request low latency behaviour */
-
-#define ASYNC_BUGGY_UART 0x4000 /* This is a buggy UART, skip some safety
- * checks. Note: can be dangerous! */
-
-#define ASYNC_AUTOPROBE 0x8000 /* Port was autoprobed by PCI or PNP code */
-
-#define ASYNC_FLAGS 0x7FFF /* Possible legal async flags */
-#define ASYNC_USR_MASK 0x3430 /* Legal flags that non-privileged
- * users can set or reset */
-
-/* Internal flags used only by kernel/chr_drv/serial.c */
-#define ASYNC_INITIALIZED 0x80000000 /* Serial port was initialized */
-#define ASYNC_NORMAL_ACTIVE 0x20000000 /* Normal device is active */
-#define ASYNC_BOOT_AUTOCONF 0x10000000 /* Autoconfigure port on bootup */
-#define ASYNC_CLOSING 0x08000000 /* Serial port is closing */
-#define ASYNC_CTS_FLOW 0x04000000 /* Do CTS flow control */
-#define ASYNC_CHECK_CD 0x02000000 /* i.e., CLOCAL */
-#define ASYNC_SHARE_IRQ 0x01000000 /* for multifunction cards
- --- no longer used */
-#define ASYNC_CONS_FLOW 0x00800000 /* flow control for console */
-
-#define ASYNC_BOOT_ONLYMCA 0x00400000 /* Probe only if MCA bus */
-#define ASYNC_INTERNAL_FLAGS 0xFFC00000 /* Internal flags */
+#define ASYNCB_HUP_NOTIFY 0 /* Notify getty on hangups and closes
+ * on the callout port */
+#define ASYNCB_FOURPORT 1 /* Set OU1, OUT2 per AST Fourport settings */
+#define ASYNCB_SAK 2 /* Secure Attention Key (Orange book) */
+#define ASYNCB_SPLIT_TERMIOS 3 /* Separate termios for dialin/callout */
+#define ASYNCB_SPD_HI 4 /* Use 56000 instead of 38400 bps */
+#define ASYNCB_SPD_VHI 5 /* Use 115200 instead of 38400 bps */
+#define ASYNCB_SKIP_TEST 6 /* Skip UART test during autoconfiguration */
+#define ASYNCB_AUTO_IRQ 7 /* Do automatic IRQ during
+ * autoconfiguration */
+#define ASYNCB_SESSION_LOCKOUT 8 /* Lock out cua opens based on session */
+#define ASYNCB_PGRP_LOCKOUT 9 /* Lock out cua opens based on pgrp */
+#define ASYNCB_CALLOUT_NOHUP 10 /* Don't do hangups for cua device */
+#define ASYNCB_HARDPPS_CD 11 /* Call hardpps when CD goes high */
+#define ASYNCB_SPD_SHI 12 /* Use 230400 instead of 38400 bps */
+#define ASYNCB_LOW_LATENCY 13 /* Request low latency behaviour */
+#define ASYNCB_BUGGY_UART 14 /* This is a buggy UART, skip some safety
+ * checks. Note: can be dangerous! */
+#define ASYNCB_AUTOPROBE 15 /* Port was autoprobed by PCI or PNP code */
+#define ASYNCB_LAST_USER 15
+
+/* Internal flags used only by kernel */
+#define ASYNCB_INITIALIZED 31 /* Serial port was initialized */
+#define ASYNCB_NORMAL_ACTIVE 29 /* Normal device is active */
+#define ASYNCB_BOOT_AUTOCONF 28 /* Autoconfigure port on bootup */
+#define ASYNCB_CLOSING 27 /* Serial port is closing */
+#define ASYNCB_CTS_FLOW 26 /* Do CTS flow control */
+#define ASYNCB_CHECK_CD 25 /* i.e., CLOCAL */
+#define ASYNCB_SHARE_IRQ 24 /* for multifunction cards, no longer used */
+#define ASYNCB_CONS_FLOW 23 /* flow control for console */
+#define ASYNCB_BOOT_ONLYMCA 22 /* Probe only if MCA bus */
+#define ASYNCB_FIRST_KERNEL 22
+
+#define ASYNC_HUP_NOTIFY (1U << ASYNCB_HUP_NOTIFY)
+#define ASYNC_FOURPORT (1U << ASYNCB_FOURPORT)
+#define ASYNC_SAK (1U << ASYNCB_SAK)
+#define ASYNC_SPLIT_TERMIOS (1U << ASYNCB_SPLIT_TERMIOS)
+#define ASYNC_SPD_HI (1U << ASYNCB_SPD_HI)
+#define ASYNC_SPD_VHI (1U << ASYNCB_SPD_VHI)
+#define ASYNC_SKIP_TEST (1U << ASYNCB_SKIP_TEST)
+#define ASYNC_AUTO_IRQ (1U << ASYNCB_AUTO_IRQ)
+#define ASYNC_SESSION_LOCKOUT (1U << ASYNCB_SESSION_LOCKOUT)
+#define ASYNC_PGRP_LOCKOUT (1U << ASYNCB_PGRP_LOCKOUT)
+#define ASYNC_CALLOUT_NOHUP (1U << ASYNCB_CALLOUT_NOHUP)
+#define ASYNC_HARDPPS_CD (1U << ASYNCB_HARDPPS_CD)
+#define ASYNC_SPD_SHI (1U << ASYNCB_SPD_SHI)
+#define ASYNC_LOW_LATENCY (1U << ASYNCB_LOW_LATENCY)
+#define ASYNC_BUGGY_UART (1U << ASYNCB_BUGGY_UART)
+#define ASYNC_AUTOPROBE (1U << ASYNCB_AUTOPROBE)
+
+#define ASYNC_FLAGS ((1U << ASYNCB_LAST_USER) - 1)
+#define ASYNC_USR_MASK (ASYNC_SPD_HI|ASYNC_SPD_VHI| \
+ ASYNC_CALLOUT_NOHUP|ASYNC_SPD_SHI|ASYNC_LOW_LATENCY)
+#define ASYNC_SPD_CUST (ASYNC_SPD_HI|ASYNC_SPD_VHI)
+#define ASYNC_SPD_WARP (ASYNC_SPD_HI|ASYNC_SPD_SHI)
+#define ASYNC_SPD_MASK (ASYNC_SPD_HI|ASYNC_SPD_VHI|ASYNC_SPD_SHI)
+
+#define ASYNC_INITIALIZED (1U << ASYNCB_INITIALIZED)
+#define ASYNC_NORMAL_ACTIVE (1U << ASYNCB_NORMAL_ACTIVE)
+#define ASYNC_BOOT_AUTOCONF (1U << ASYNCB_BOOT_AUTOCONF)
+#define ASYNC_CLOSING (1U << ASYNCB_CLOSING)
+#define ASYNC_CTS_FLOW (1U << ASYNCB_CTS_FLOW)
+#define ASYNC_CHECK_CD (1U << ASYNCB_CHECK_CD)
+#define ASYNC_SHARE_IRQ (1U << ASYNCB_SHARE_IRQ)
+#define ASYNC_CONS_FLOW (1U << ASYNCB_CONS_FLOW)
+#define ASYNC_BOOT_ONLYMCA (1U << ASYNCB_BOOT_ONLYMCA)
+#define ASYNC_INTERNAL_FLAGS (~((1U << ASYNCB_FIRST_KERNEL) - 1))
/*
* Multiport serial configuration structure --- external structure
int reserved[9];
};
+/*
+ * Serial interface for controlling RS485 settings on chips with suitable
+ * support. Set with TIOCSRS485 and get with TIOCGRS485 if supported by your
+ * platform. The set function returns the new state, with any unsupported bits
+ * reverted appropriately.
+ */
+
+struct serial_rs485 {
+ __u32 flags; /* RS485 feature flags */
+#define SER_RS485_ENABLED (1 << 0)
+#define SER_RS485_RTS_ON_SEND (1 << 1)
+#define SER_RS485_RTS_AFTER_SEND (1 << 2)
+ __u32 delay_rts_before_send; /* Milliseconds */
+ __u32 padding[6]; /* Memory is cheap, new structs
+ are a royal PITA .. */
+};
#ifdef __KERNEL__
-/* Export to allow PCMCIA to use this - Dave Hinds */
-extern int register_serial(struct serial_struct *req);
-extern void unregister_serial(int line);
-
-/* Allow architectures to override entries in serial8250_ports[] at run time: */
-struct uart_port; /* forward declaration */
-extern int early_serial_setup(struct uart_port *port);
-extern int early_serial_console_init(char *options);
-extern int serial8250_start_console(struct uart_port *port, char *options);
+#include <linux/compiler.h>
#endif /* __KERNEL__ */
#endif /* _LINUX_SERIAL_H */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff