* or, if no MAC address given, all stations, on the interface identified
* by %NL80211_ATTR_IFINDEX.
*
+ * @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to
+ * destination %NL80211_ATTR_MAC on the interface identified by
+ * %NL80211_ATTR_IFINDEX.
+ * @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to
+ * destination %NL80211_ATTR_MAC on the interface identified by
+ * %NL80211_ATTR_IFINDEX.
+ * @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the
+ * the interface identified by %NL80211_ATTR_IFINDEX.
+ * @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC
+ * or, if no MAC address given, all mesh paths, on the interface identified
+ * by %NL80211_ATTR_IFINDEX.
+ * @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by
+ * %NL80211_ATTR_IFINDEX.
+ *
+ * @NL80211_CMD_SET_REG: Set current regulatory domain. CRDA sends this command
+ * after being queried by the kernel. CRDA replies by sending a regulatory
+ * domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our
+ * current alpha2 if it found a match. It also provides
+ * NL80211_ATTR_REG_RULE_FLAGS, and a set of regulatory rules. Each
+ * regulatory rule is a nested set of attributes given by
+ * %NL80211_ATTR_REG_RULE_FREQ_[START|END] and
+ * %NL80211_ATTR_FREQ_RANGE_MAX_BW with an attached power rule given by
+ * %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and
+ * %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP.
+ * @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
+ * to the the specified ISO/IEC 3166-1 alpha2 country code. The core will
+ * store this as a valid request and then query userspace for it.
+ *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
NL80211_CMD_NEW_STATION,
NL80211_CMD_DEL_STATION,
- /* add commands here */
+ NL80211_CMD_GET_MPATH,
+ NL80211_CMD_SET_MPATH,
+ NL80211_CMD_NEW_MPATH,
+ NL80211_CMD_DEL_MPATH,
+
+ NL80211_CMD_SET_BSS,
+
+ NL80211_CMD_SET_REG,
+ NL80211_CMD_REQ_SET_REG,
+
+ /* add new commands above here */
/* used to define NL80211_CMD_MAX below */
__NL80211_CMD_AFTER_LAST,
NL80211_CMD_MAX = __NL80211_CMD_AFTER_LAST - 1
};
+/*
+ * Allow user space programs to use #ifdef on new commands by defining them
+ * here
+ */
+#define NL80211_CMD_SET_BSS NL80211_CMD_SET_BSS
/**
* enum nl80211_attrs - nl80211 netlink attributes
* restriction (at most %NL80211_MAX_SUPP_RATES).
* @NL80211_ATTR_STA_VLAN: interface index of VLAN interface to move station
* to, or the AP interface the station was originally added to to.
- * @NL80211_ATTR_STA_STATS: statistics for a station, part of station info
+ * @NL80211_ATTR_STA_INFO: information about a station, part of station info
* given for %NL80211_CMD_GET_STATION, nested attribute containing
- * info as possible, see &enum nl80211_sta_stats.
+ * info as possible, see &enum nl80211_sta_info.
*
* @NL80211_ATTR_WIPHY_BANDS: Information about an operating bands,
* consisting of a nested array.
*
+ * @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).
+ * @NL80211_ATTR_PLINK_ACTION: action to perform on the mesh peer link.
+ * @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path.
+ * @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path
+ * info given for %NL80211_CMD_GET_MPATH, nested attribute described at
+ * &enum nl80211_mpath_info.
+ *
+ * @NL80211_ATTR_MNTR_FLAGS: flags, nested element with NLA_FLAG attributes of
+ * &enum nl80211_mntr_flags.
+ *
+ * @NL80211_ATTR_REG_ALPHA2: an ISO-3166-alpha2 country code for which the
+ * current regulatory domain should be set to or is already set to.
+ * For example, 'CR', for Costa Rica. This attribute is used by the kernel
+ * to query the CRDA to retrieve one regulatory domain. This attribute can
+ * also be used by userspace to query the kernel for the currently set
+ * regulatory domain. We chose an alpha2 as that is also used by the
+ * IEEE-802.11d country information element to identify a country.
+ * Users can also simply ask the wireless core to set regulatory domain
+ * to a specific alpha2.
+ * @NL80211_ATTR_REG_RULES: a nested array of regulatory domain regulatory
+ * rules.
+ *
+ * @NL80211_ATTR_BSS_CTS_PROT: whether CTS protection is enabled (u8, 0 or 1)
+ * @NL80211_ATTR_BSS_SHORT_PREAMBLE: whether short preamble is enabled
+ * (u8, 0 or 1)
+ * @NL80211_ATTR_BSS_SHORT_SLOT_TIME: whether short slot time enabled
+ * (u8, 0 or 1)
+ *
+ * @NL80211_ATTR_HT_CAPABILITY: HT Capability information element (from
+ * association request when used with NL80211_CMD_NEW_STATION)
+ *
+ * @NL80211_ATTR_SUPPORTED_IFTYPES: nested attribute containing all
+ * supported interface types, each a flag attribute with the number
+ * of the interface mode.
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
NL80211_ATTR_STA_LISTEN_INTERVAL,
NL80211_ATTR_STA_SUPPORTED_RATES,
NL80211_ATTR_STA_VLAN,
- NL80211_ATTR_STA_STATS,
+ NL80211_ATTR_STA_INFO,
NL80211_ATTR_WIPHY_BANDS,
+ NL80211_ATTR_MNTR_FLAGS,
+
+ NL80211_ATTR_MESH_ID,
+ NL80211_ATTR_STA_PLINK_ACTION,
+ NL80211_ATTR_MPATH_NEXT_HOP,
+ NL80211_ATTR_MPATH_INFO,
+
+ NL80211_ATTR_BSS_CTS_PROT,
+ NL80211_ATTR_BSS_SHORT_PREAMBLE,
+ NL80211_ATTR_BSS_SHORT_SLOT_TIME,
+
+ NL80211_ATTR_HT_CAPABILITY,
+
+ NL80211_ATTR_SUPPORTED_IFTYPES,
+
+ NL80211_ATTR_REG_ALPHA2,
+ NL80211_ATTR_REG_RULES,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
NL80211_ATTR_MAX = __NL80211_ATTR_AFTER_LAST - 1
};
-#define NL80211_MAX_SUPP_RATES 32
+/*
+ * Allow user space programs to use #ifdef on new attributes by defining them
+ * here
+ */
+#define NL80211_ATTR_HT_CAPABILITY NL80211_ATTR_HT_CAPABILITY
+
+#define NL80211_MAX_SUPP_RATES 32
+#define NL80211_MAX_SUPP_REG_RULES 32
+#define NL80211_TKIP_DATA_OFFSET_ENCR_KEY 0
+#define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16
+#define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24
+#define NL80211_HT_CAPABILITY_LEN 26
/**
* enum nl80211_iftype - (virtual) interface types
* @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points
* @NL80211_IFTYPE_WDS: wireless distribution interface
* @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
+ * @NL80211_IFTYPE_MESH_POINT: mesh point
* @NL80211_IFTYPE_MAX: highest interface type number currently defined
* @__NL80211_IFTYPE_AFTER_LAST: internal use
*
NL80211_IFTYPE_AP_VLAN,
NL80211_IFTYPE_WDS,
NL80211_IFTYPE_MONITOR,
+ NL80211_IFTYPE_MESH_POINT,
/* keep last */
__NL80211_IFTYPE_AFTER_LAST,
};
/**
- * enum nl80211_sta_stats - station statistics
+ * enum nl80211_sta_info - station information
*
- * These attribute types are used with %NL80211_ATTR_STA_STATS
+ * These attribute types are used with %NL80211_ATTR_STA_INFO
* when getting information about a station.
*
- * @__NL80211_STA_STAT_INVALID: attribute number 0 is reserved
- * @NL80211_STA_STAT_INACTIVE_TIME: time since last activity (u32, msecs)
- * @NL80211_STA_STAT_RX_BYTES: total received bytes (u32, from this station)
- * @NL80211_STA_STAT_TX_BYTES: total transmitted bytes (u32, to this station)
- * @__NL80211_STA_STAT_AFTER_LAST: internal
- * @NL80211_STA_STAT_MAX: highest possible station stats attribute
+ * @__NL80211_STA_INFO_INVALID: attribute number 0 is reserved
+ * @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs)
+ * @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station)
+ * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station)
+ * @__NL80211_STA_INFO_AFTER_LAST: internal
+ * @NL80211_STA_INFO_MAX: highest possible station info attribute
+ */
+enum nl80211_sta_info {
+ __NL80211_STA_INFO_INVALID,
+ NL80211_STA_INFO_INACTIVE_TIME,
+ NL80211_STA_INFO_RX_BYTES,
+ NL80211_STA_INFO_TX_BYTES,
+ NL80211_STA_INFO_LLID,
+ NL80211_STA_INFO_PLID,
+ NL80211_STA_INFO_PLINK_STATE,
+
+ /* keep last */
+ __NL80211_STA_INFO_AFTER_LAST,
+ NL80211_STA_INFO_MAX = __NL80211_STA_INFO_AFTER_LAST - 1
+};
+
+/**
+ * enum nl80211_mpath_flags - nl80211 mesh path flags
+ *
+ * @NL80211_MPATH_FLAG_ACTIVE: the mesh path is active
+ * @NL80211_MPATH_FLAG_RESOLVING: the mesh path discovery process is running
+ * @NL80211_MPATH_FLAG_DSN_VALID: the mesh path contains a valid DSN
+ * @NL80211_MPATH_FLAG_FIXED: the mesh path has been manually set
+ * @NL80211_MPATH_FLAG_RESOLVED: the mesh path discovery process succeeded
+ */
+enum nl80211_mpath_flags {
+ NL80211_MPATH_FLAG_ACTIVE = 1<<0,
+ NL80211_MPATH_FLAG_RESOLVING = 1<<1,
+ NL80211_MPATH_FLAG_DSN_VALID = 1<<2,
+ NL80211_MPATH_FLAG_FIXED = 1<<3,
+ NL80211_MPATH_FLAG_RESOLVED = 1<<4,
+};
+
+/**
+ * enum nl80211_mpath_info - mesh path information
+ *
+ * These attribute types are used with %NL80211_ATTR_MPATH_INFO when getting
+ * information about a mesh path.
+ *
+ * @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved
+ * @NL80211_ATTR_MPATH_FRAME_QLEN: number of queued frames for this destination
+ * @NL80211_ATTR_MPATH_DSN: destination sequence number
+ * @NL80211_ATTR_MPATH_METRIC: metric (cost) of this mesh path
+ * @NL80211_ATTR_MPATH_EXPTIME: expiration time for the path, in msec from now
+ * @NL80211_ATTR_MPATH_FLAGS: mesh path flags, enumerated in
+ * &enum nl80211_mpath_flags;
+ * @NL80211_ATTR_MPATH_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
+ * @NL80211_ATTR_MPATH_DISCOVERY_RETRIES: mesh path discovery retries
*/
-enum nl80211_sta_stats {
- __NL80211_STA_STAT_INVALID,
- NL80211_STA_STAT_INACTIVE_TIME,
- NL80211_STA_STAT_RX_BYTES,
- NL80211_STA_STAT_TX_BYTES,
+enum nl80211_mpath_info {
+ __NL80211_MPATH_INFO_INVALID,
+ NL80211_MPATH_INFO_FRAME_QLEN,
+ NL80211_MPATH_INFO_DSN,
+ NL80211_MPATH_INFO_METRIC,
+ NL80211_MPATH_INFO_EXPTIME,
+ NL80211_MPATH_INFO_FLAGS,
+ NL80211_MPATH_INFO_DISCOVERY_TIMEOUT,
+ NL80211_MPATH_INFO_DISCOVERY_RETRIES,
/* keep last */
- __NL80211_STA_STAT_AFTER_LAST,
- NL80211_STA_STAT_MAX = __NL80211_STA_STAT_AFTER_LAST - 1
+ __NL80211_MPATH_INFO_AFTER_LAST,
+ NL80211_MPATH_INFO_MAX = __NL80211_MPATH_INFO_AFTER_LAST - 1
};
/**
NL80211_BITRATE_ATTR_MAX = __NL80211_BITRATE_ATTR_AFTER_LAST - 1
};
+/**
+ * enum nl80211_reg_rule_attr - regulatory rule attributes
+ * @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional
+ * considerations for a given frequency range. These are the
+ * &enum nl80211_reg_rule_flags.
+ * @NL80211_ATTR_FREQ_RANGE_START: starting frequencry for the regulatory
+ * rule in KHz. This is not a center of frequency but an actual regulatory
+ * band edge.
+ * @NL80211_ATTR_FREQ_RANGE_END: ending frequency for the regulatory rule
+ * in KHz. This is not a center a frequency but an actual regulatory
+ * band edge.
+ * @NL80211_ATTR_FREQ_RANGE_MAX_BW: maximum allowed bandwidth for this
+ * frequency range, in KHz.
+ * @NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN: the maximum allowed antenna gain
+ * for a given frequency range. The value is in mBi (100 * dBi).
+ * If you don't have one then don't send this.
+ * @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for
+ * a given frequency range. The value is in mBm (100 * dBm).
+ */
+enum nl80211_reg_rule_attr {
+ __NL80211_REG_RULE_ATTR_INVALID,
+ NL80211_ATTR_REG_RULE_FLAGS,
+
+ NL80211_ATTR_FREQ_RANGE_START,
+ NL80211_ATTR_FREQ_RANGE_END,
+ NL80211_ATTR_FREQ_RANGE_MAX_BW,
+
+ NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN,
+ NL80211_ATTR_POWER_RULE_MAX_EIRP,
+
+ /* keep last */
+ __NL80211_REG_RULE_ATTR_AFTER_LAST,
+ NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1
+};
+
+/**
+ * enum nl80211_reg_rule_flags - regulatory rule flags
+ *
+ * @NL80211_RRF_NO_OFDM: OFDM modulation not allowed
+ * @NL80211_RRF_NO_CCK: CCK modulation not allowed
+ * @NL80211_RRF_NO_INDOOR: indoor operation not allowed
+ * @NL80211_RRF_NO_OUTDOOR: outdoor operation not allowed
+ * @NL80211_RRF_DFS: DFS support is required to be used
+ * @NL80211_RRF_PTP_ONLY: this is only for Point To Point links
+ * @NL80211_RRF_PTMP_ONLY: this is only for Point To Multi Point links
+ * @NL80211_RRF_PASSIVE_SCAN: passive scan is required
+ * @NL80211_RRF_NO_IBSS: no IBSS is allowed
+ */
+enum nl80211_reg_rule_flags {
+ NL80211_RRF_NO_OFDM = 1<<0,
+ NL80211_RRF_NO_CCK = 1<<1,
+ NL80211_RRF_NO_INDOOR = 1<<2,
+ NL80211_RRF_NO_OUTDOOR = 1<<3,
+ NL80211_RRF_DFS = 1<<4,
+ NL80211_RRF_PTP_ONLY = 1<<5,
+ NL80211_RRF_PTMP_ONLY = 1<<6,
+ NL80211_RRF_PASSIVE_SCAN = 1<<7,
+ NL80211_RRF_NO_IBSS = 1<<8,
+};
+
+/**
+ * enum nl80211_mntr_flags - monitor configuration flags
+ *
+ * Monitor configuration flags.
+ *
+ * @__NL80211_MNTR_FLAG_INVALID: reserved
+ *
+ * @NL80211_MNTR_FLAG_FCSFAIL: pass frames with bad FCS
+ * @NL80211_MNTR_FLAG_PLCPFAIL: pass frames with bad PLCP
+ * @NL80211_MNTR_FLAG_CONTROL: pass control frames
+ * @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering
+ * @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing.
+ * overrides all other flags.
+ *
+ * @__NL80211_MNTR_FLAG_AFTER_LAST: internal use
+ * @NL80211_MNTR_FLAG_MAX: highest possible monitor flag
+ */
+enum nl80211_mntr_flags {
+ __NL80211_MNTR_FLAG_INVALID,
+ NL80211_MNTR_FLAG_FCSFAIL,
+ NL80211_MNTR_FLAG_PLCPFAIL,
+ NL80211_MNTR_FLAG_CONTROL,
+ NL80211_MNTR_FLAG_OTHER_BSS,
+ NL80211_MNTR_FLAG_COOK_FRAMES,
+
+ /* keep last */
+ __NL80211_MNTR_FLAG_AFTER_LAST,
+ NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1
+};
+
#endif /* __LINUX_NL80211_H */