#ifndef __PXA_REGS_H
#define __PXA_REGS_H
-#include <linux/config.h>
/*
* PXA Chip selects
#define DCSR_SETCMPST (1 << 25) /* Set Descriptor Compare Status */
#define DCSR_CLRCMPST (1 << 24) /* Clear Descriptor Compare Status */
#define DCSR_CMPST (1 << 10) /* The Descriptor Compare Status */
-#define DCSR_ENRINTR (1 << 9) /* The end of Receive */
+#define DCSR_EORINTR (1 << 9) /* The end of Receive */
#endif
#define DCSR_REQPEND (1 << 8) /* Request Pending (read-only) */
#define DCSR_STOPSTATE (1 << 3) /* Stop State (read-only) */
#define DCSR_STARTINTR (1 << 1) /* Start Interrupt (read / write) */
#define DCSR_BUSERR (1 << 0) /* Bus Error Interrupt (read / write) */
+#define DALGN __REG(0x400000a0) /* DMA Alignment Register */
#define DINT __REG(0x400000f0) /* DMA Interrupt Register */
-#define DRCMR(n) __REG2(0x40000100, (n)<<2)
+#define DRCMR(n) (*(((n) < 64) ? \
+ &__REG2(0x40000100, ((n) & 0x3f) << 2) : \
+ &__REG2(0x40001100, ((n) & 0x3f) << 2)))
+
#define DRCMR0 __REG(0x40000100) /* Request to Channel Map Register for DREQ 0 */
#define DRCMR1 __REG(0x40000104) /* Request to Channel Map Register for DREQ 1 */
#define DRCMR2 __REG(0x40000108) /* Request to Channel Map Register for I2S receive Request */
#define DRCMR12 __REG(0x40000130) /* Request to Channel Map Register for AC97 audio transmit Request */
#define DRCMR13 __REG(0x40000134) /* Request to Channel Map Register for SSP receive Request */
#define DRCMR14 __REG(0x40000138) /* Request to Channel Map Register for SSP transmit Request */
-#define DRCMR15 __REG(0x4000013c) /* Reserved */
-#define DRCMR16 __REG(0x40000140) /* Reserved */
+#define DRCMR15 __REG(0x4000013c) /* Request to Channel Map Register for SSP2 receive Request */
+#define DRCMR16 __REG(0x40000140) /* Request to Channel Map Register for SSP2 transmit Request */
#define DRCMR17 __REG(0x40000144) /* Request to Channel Map Register for ICP receive Request */
#define DRCMR18 __REG(0x40000148) /* Request to Channel Map Register for ICP transmit Request */
#define DRCMR19 __REG(0x4000014c) /* Request to Channel Map Register for STUART receive Request */
#define DRCMR37 __REG(0x40000194) /* Request to Channel Map Register for USB endpoint 13 Request */
#define DRCMR38 __REG(0x40000198) /* Request to Channel Map Register for USB endpoint 14 Request */
#define DRCMR39 __REG(0x4000019C) /* Reserved */
-
+#define DRCMR66 __REG(0x40001108) /* Request to Channel Map Register for SSP3 receive Request */
+#define DRCMR67 __REG(0x4000110C) /* Request to Channel Map Register for SSP3 transmit Request */
#define DRCMR68 __REG(0x40001110) /* Request to Channel Map Register for Camera FIFO 0 Request */
#define DRCMR69 __REG(0x40001114) /* Request to Channel Map Register for Camera FIFO 1 Request */
#define DRCMR70 __REG(0x40001118) /* Request to Channel Map Register for Camera FIFO 2 Request */
#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */
#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */
+/* Hardware UART (HWUART) */
+#define HWUART HWRBR
+#define HWRBR __REG(0x41600000) /* Receive Buffer Register (read only) */
+#define HWTHR __REG(0x41600000) /* Transmit Holding Register (write only) */
+#define HWIER __REG(0x41600004) /* Interrupt Enable Register (read/write) */
+#define HWIIR __REG(0x41600008) /* Interrupt ID Register (read only) */
+#define HWFCR __REG(0x41600008) /* FIFO Control Register (write only) */
+#define HWLCR __REG(0x4160000C) /* Line Control Register (read/write) */
+#define HWMCR __REG(0x41600010) /* Modem Control Register (read/write) */
+#define HWLSR __REG(0x41600014) /* Line Status Register (read only) */
+#define HWMSR __REG(0x41600018) /* Modem Status Register (read only) */
+#define HWSPR __REG(0x4160001C) /* Scratch Pad Register (read/write) */
+#define HWISR __REG(0x41600020) /* Infrared Selection Register (read/write) */
+#define HWFOR __REG(0x41600024) /* Receive FIFO Occupancy Register (read only) */
+#define HWABR __REG(0x41600028) /* Auto-Baud Control Register (read/write) */
+#define HWACR __REG(0x4160002C) /* Auto-Baud Count Register (read only) */
+#define HWDLL __REG(0x41600000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */
+#define HWDLH __REG(0x41600004) /* Divisor Latch High Register (DLAB = 1) (read/write) */
+
#define IER_DMAE (1 << 7) /* DMA Requests Enable */
#define IER_UUE (1 << 6) /* UART Unit Enable */
#define IER_NRZE (1 << 5) /* NRZ coding Enable */
* Serial Audio Controller
*/
-/* FIXME: This clash with SA1111 defines */
-#ifndef _ASM_ARCH_SA1111
-
#define SACR0 __REG(0x40400000) /* Global Control Register */
#define SACR1 __REG(0x40400004) /* Serial Audio I 2 S/MSB-Justified Control Register */
#define SASR0 __REG(0x4040000C) /* Serial Audio I 2 S/MSB-Justified Interface and FIFO Status Register */
#define SADIV __REG(0x40400060) /* Audio Clock Divider Register. */
#define SADR __REG(0x40400080) /* Serial Audio Data Register (TX and RX FIFO access Register). */
-#define SACR0_RFTH(x) (x << 12) /* Rx FIFO Interrupt or DMA Trigger Threshold */
-#define SACR0_TFTH(x) (x << 8) /* Tx FIFO Interrupt or DMA Trigger Threshold */
+#define SACR0_RFTH(x) ((x) << 12) /* Rx FIFO Interrupt or DMA Trigger Threshold */
+#define SACR0_TFTH(x) ((x) << 8) /* Tx FIFO Interrupt or DMA Trigger Threshold */
#define SACR0_STRF (1 << 5) /* FIFO Select for EFWR Special Function */
#define SACR0_EFWR (1 << 4) /* Enable EFWR Function */
#define SACR0_RST (1 << 3) /* FIFO, i2s Register Reset */
#define SACR1_ENLBF (1 << 5) /* Enable Loopback */
#define SACR1_DRPL (1 << 4) /* Disable Replaying Function */
#define SACR1_DREC (1 << 3) /* Disable Recording Function */
-#define SACR1_AMSL (1 << 1) /* Specify Alternate Mode */
+#define SACR1_AMSL (1 << 0) /* Specify Alternate Mode */
#define SASR0_I2SOFF (1 << 7) /* Controller Status */
#define SASR0_ROR (1 << 6) /* Rx FIFO Overrun */
#define SAIMR_RFS (1 << 4) /* Enable Rx FIFO Service Interrupt */
#define SAIMR_TFS (1 << 3) /* Enable Tx FIFO Service Interrupt */
-#endif
-
/*
* AC97 Controller registers
*/
#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
#define GCR __REG(0x4050000C) /* Global Control Register */
+#ifdef CONFIG_PXA3xx
+#define GCR_CLKBPB (1 << 31) /* Internal clock enable */
+#endif
#define GCR_nDMAEN (1 << 24) /* non DMA Enable */
#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */
#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */
/*
- * USB Device Controller
- * PXA25x and PXA27x USB device controller registers are different.
- */
-#if defined(CONFIG_PXA25x)
-
-#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */
-#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */
-#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */
-
-#define UDCCR __REG(0x40600000) /* UDC Control Register */
-#define UDCCR_UDE (1 << 0) /* UDC enable */
-#define UDCCR_UDA (1 << 1) /* UDC active */
-#define UDCCR_RSM (1 << 2) /* Device resume */
-#define UDCCR_RESIR (1 << 3) /* Resume interrupt request */
-#define UDCCR_SUSIR (1 << 4) /* Suspend interrupt request */
-#define UDCCR_SRM (1 << 5) /* Suspend/resume interrupt mask */
-#define UDCCR_RSTIR (1 << 6) /* Reset interrupt request */
-#define UDCCR_REM (1 << 7) /* Reset interrupt mask */
-
-#define UDCCS0 __REG(0x40600010) /* UDC Endpoint 0 Control/Status Register */
-#define UDCCS0_OPR (1 << 0) /* OUT packet ready */
-#define UDCCS0_IPR (1 << 1) /* IN packet ready */
-#define UDCCS0_FTF (1 << 2) /* Flush Tx FIFO */
-#define UDCCS0_DRWF (1 << 3) /* Device remote wakeup feature */
-#define UDCCS0_SST (1 << 4) /* Sent stall */
-#define UDCCS0_FST (1 << 5) /* Force stall */
-#define UDCCS0_RNE (1 << 6) /* Receive FIFO no empty */
-#define UDCCS0_SA (1 << 7) /* Setup active */
-
-/* Bulk IN - Endpoint 1,6,11 */
-#define UDCCS1 __REG(0x40600014) /* UDC Endpoint 1 (IN) Control/Status Register */
-#define UDCCS6 __REG(0x40600028) /* UDC Endpoint 6 (IN) Control/Status Register */
-#define UDCCS11 __REG(0x4060003C) /* UDC Endpoint 11 (IN) Control/Status Register */
-
-#define UDCCS_BI_TFS (1 << 0) /* Transmit FIFO service */
-#define UDCCS_BI_TPC (1 << 1) /* Transmit packet complete */
-#define UDCCS_BI_FTF (1 << 2) /* Flush Tx FIFO */
-#define UDCCS_BI_TUR (1 << 3) /* Transmit FIFO underrun */
-#define UDCCS_BI_SST (1 << 4) /* Sent stall */
-#define UDCCS_BI_FST (1 << 5) /* Force stall */
-#define UDCCS_BI_TSP (1 << 7) /* Transmit short packet */
-
-/* Bulk OUT - Endpoint 2,7,12 */
-#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */
-#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */
-#define UDCCS12 __REG(0x40600040) /* UDC Endpoint 12 (OUT) Control/Status Register */
-
-#define UDCCS_BO_RFS (1 << 0) /* Receive FIFO service */
-#define UDCCS_BO_RPC (1 << 1) /* Receive packet complete */
-#define UDCCS_BO_DME (1 << 3) /* DMA enable */
-#define UDCCS_BO_SST (1 << 4) /* Sent stall */
-#define UDCCS_BO_FST (1 << 5) /* Force stall */
-#define UDCCS_BO_RNE (1 << 6) /* Receive FIFO not empty */
-#define UDCCS_BO_RSP (1 << 7) /* Receive short packet */
-
-/* Isochronous IN - Endpoint 3,8,13 */
-#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */
-#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */
-#define UDCCS13 __REG(0x40600044) /* UDC Endpoint 13 (IN) Control/Status Register */
-
-#define UDCCS_II_TFS (1 << 0) /* Transmit FIFO service */
-#define UDCCS_II_TPC (1 << 1) /* Transmit packet complete */
-#define UDCCS_II_FTF (1 << 2) /* Flush Tx FIFO */
-#define UDCCS_II_TUR (1 << 3) /* Transmit FIFO underrun */
-#define UDCCS_II_TSP (1 << 7) /* Transmit short packet */
-
-/* Isochronous OUT - Endpoint 4,9,14 */
-#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */
-#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */
-#define UDCCS14 __REG(0x40600048) /* UDC Endpoint 14 (OUT) Control/Status Register */
-
-#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */
-#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */
-#define UDCCS_IO_ROF (1 << 3) /* Receive overflow */
-#define UDCCS_IO_DME (1 << 3) /* DMA enable */
-#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */
-#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */
-
-/* Interrupt IN - Endpoint 5,10,15 */
-#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */
-#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */
-#define UDCCS15 __REG(0x4060004C) /* UDC Endpoint 15 (Interrupt) Control/Status Register */
-
-#define UDCCS_INT_TFS (1 << 0) /* Transmit FIFO service */
-#define UDCCS_INT_TPC (1 << 1) /* Transmit packet complete */
-#define UDCCS_INT_FTF (1 << 2) /* Flush Tx FIFO */
-#define UDCCS_INT_TUR (1 << 3) /* Transmit FIFO underrun */
-#define UDCCS_INT_SST (1 << 4) /* Sent stall */
-#define UDCCS_INT_FST (1 << 5) /* Force stall */
-#define UDCCS_INT_TSP (1 << 7) /* Transmit short packet */
-
-#define UFNRH __REG(0x40600060) /* UDC Frame Number Register High */
-#define UFNRL __REG(0x40600064) /* UDC Frame Number Register Low */
-#define UBCR2 __REG(0x40600068) /* UDC Byte Count Reg 2 */
-#define UBCR4 __REG(0x4060006c) /* UDC Byte Count Reg 4 */
-#define UBCR7 __REG(0x40600070) /* UDC Byte Count Reg 7 */
-#define UBCR9 __REG(0x40600074) /* UDC Byte Count Reg 9 */
-#define UBCR12 __REG(0x40600078) /* UDC Byte Count Reg 12 */
-#define UBCR14 __REG(0x4060007c) /* UDC Byte Count Reg 14 */
-#define UDDR0 __REG(0x40600080) /* UDC Endpoint 0 Data Register */
-#define UDDR1 __REG(0x40600100) /* UDC Endpoint 1 Data Register */
-#define UDDR2 __REG(0x40600180) /* UDC Endpoint 2 Data Register */
-#define UDDR3 __REG(0x40600200) /* UDC Endpoint 3 Data Register */
-#define UDDR4 __REG(0x40600400) /* UDC Endpoint 4 Data Register */
-#define UDDR5 __REG(0x406000A0) /* UDC Endpoint 5 Data Register */
-#define UDDR6 __REG(0x40600600) /* UDC Endpoint 6 Data Register */
-#define UDDR7 __REG(0x40600680) /* UDC Endpoint 7 Data Register */
-#define UDDR8 __REG(0x40600700) /* UDC Endpoint 8 Data Register */
-#define UDDR9 __REG(0x40600900) /* UDC Endpoint 9 Data Register */
-#define UDDR10 __REG(0x406000C0) /* UDC Endpoint 10 Data Register */
-#define UDDR11 __REG(0x40600B00) /* UDC Endpoint 11 Data Register */
-#define UDDR12 __REG(0x40600B80) /* UDC Endpoint 12 Data Register */
-#define UDDR13 __REG(0x40600C00) /* UDC Endpoint 13 Data Register */
-#define UDDR14 __REG(0x40600E00) /* UDC Endpoint 14 Data Register */
-#define UDDR15 __REG(0x406000E0) /* UDC Endpoint 15 Data Register */
-
-#define UICR0 __REG(0x40600050) /* UDC Interrupt Control Register 0 */
-
-#define UICR0_IM0 (1 << 0) /* Interrupt mask ep 0 */
-#define UICR0_IM1 (1 << 1) /* Interrupt mask ep 1 */
-#define UICR0_IM2 (1 << 2) /* Interrupt mask ep 2 */
-#define UICR0_IM3 (1 << 3) /* Interrupt mask ep 3 */
-#define UICR0_IM4 (1 << 4) /* Interrupt mask ep 4 */
-#define UICR0_IM5 (1 << 5) /* Interrupt mask ep 5 */
-#define UICR0_IM6 (1 << 6) /* Interrupt mask ep 6 */
-#define UICR0_IM7 (1 << 7) /* Interrupt mask ep 7 */
-
-#define UICR1 __REG(0x40600054) /* UDC Interrupt Control Register 1 */
-
-#define UICR1_IM8 (1 << 0) /* Interrupt mask ep 8 */
-#define UICR1_IM9 (1 << 1) /* Interrupt mask ep 9 */
-#define UICR1_IM10 (1 << 2) /* Interrupt mask ep 10 */
-#define UICR1_IM11 (1 << 3) /* Interrupt mask ep 11 */
-#define UICR1_IM12 (1 << 4) /* Interrupt mask ep 12 */
-#define UICR1_IM13 (1 << 5) /* Interrupt mask ep 13 */
-#define UICR1_IM14 (1 << 6) /* Interrupt mask ep 14 */
-#define UICR1_IM15 (1 << 7) /* Interrupt mask ep 15 */
-
-#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */
-
-#define USIR0_IR0 (1 << 0) /* Interrup request ep 0 */
-#define USIR0_IR1 (1 << 1) /* Interrup request ep 1 */
-#define USIR0_IR2 (1 << 2) /* Interrup request ep 2 */
-#define USIR0_IR3 (1 << 3) /* Interrup request ep 3 */
-#define USIR0_IR4 (1 << 4) /* Interrup request ep 4 */
-#define USIR0_IR5 (1 << 5) /* Interrup request ep 5 */
-#define USIR0_IR6 (1 << 6) /* Interrup request ep 6 */
-#define USIR0_IR7 (1 << 7) /* Interrup request ep 7 */
-
-#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */
-
-#define USIR1_IR8 (1 << 0) /* Interrup request ep 8 */
-#define USIR1_IR9 (1 << 1) /* Interrup request ep 9 */
-#define USIR1_IR10 (1 << 2) /* Interrup request ep 10 */
-#define USIR1_IR11 (1 << 3) /* Interrup request ep 11 */
-#define USIR1_IR12 (1 << 4) /* Interrup request ep 12 */
-#define USIR1_IR13 (1 << 5) /* Interrup request ep 13 */
-#define USIR1_IR14 (1 << 6) /* Interrup request ep 14 */
-#define USIR1_IR15 (1 << 7) /* Interrup request ep 15 */
-
-#elif defined(CONFIG_PXA27x)
-
-#define UDCCR __REG(0x40600000) /* UDC Control Register */
-#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */
-#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation
- Protocol Port Support */
-#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol
- Support */
-#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol
- Enable */
-#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */
-#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */
-#define UDCCR_ACN_S 11
-#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */
-#define UDCCR_AIN_S 8
-#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface
- Setting Number */
-#define UDCCR_AAISN_S 5
-#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active
- Configuration */
-#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration
- Error */
-#define UDCCR_UDR (1 << 2) /* UDC Resume */
-#define UDCCR_UDA (1 << 1) /* UDC Active */
-#define UDCCR_UDE (1 << 0) /* UDC Enable */
-
-#define UDCICR0 __REG(0x40600004) /* UDC Interrupt Control Register0 */
-#define UDCICR1 __REG(0x40600008) /* UDC Interrupt Control Register1 */
-#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */
-#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */
-
-#define UDC_INT_FIFOERROR (0x2)
-#define UDC_INT_PACKETCMP (0x1)
-
-#define UDCICR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
-#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */
-#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */
-#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */
-#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */
-#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */
-
-#define UDCISR0 __REG(0x4060000C) /* UDC Interrupt Status Register 0 */
-#define UDCISR1 __REG(0x40600010) /* UDC Interrupt Status Register 1 */
-#define UDCISR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
-#define UDCISR1_IECC (1 << 31) /* IntEn - Configuration Change */
-#define UDCISR1_IESOF (1 << 30) /* IntEn - Start of Frame */
-#define UDCISR1_IERU (1 << 29) /* IntEn - Resume */
-#define UDCISR1_IESU (1 << 28) /* IntEn - Suspend */
-#define UDCISR1_IERS (1 << 27) /* IntEn - Reset */
-
-
-#define UDCFNR __REG(0x40600014) /* UDC Frame Number Register */
-#define UDCOTGICR __REG(0x40600018) /* UDC On-The-Go interrupt control */
-#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */
-#define UDCOTGICR_IEXR (1 << 17) /* Extra Transciever Interrupt
- Rising Edge Interrupt Enable */
-#define UDCOTGICR_IEXF (1 << 16) /* Extra Transciever Interrupt
- Falling Edge Interrupt Enable */
-#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge
- Interrupt Enable */
-#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge
- Interrupt Enable */
-#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge
- Interrupt Enable */
-#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge
- Interrupt Enable */
-#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge
- Interrupt Enable */
-#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge
- Interrupt Enable */
-#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising
- Edge Interrupt Enable */
-#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling
- Edge Interrupt Enable */
-#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge
- Interrupt Enable */
-#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge
- Interrupt Enable */
-
-#define UDCCSN(x) __REG2(0x40600100, (x) << 2)
-#define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */
-#define UDCCSR0_SA (1 << 7) /* Setup Active */
-#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */
-#define UDCCSR0_FST (1 << 5) /* Force Stall */
-#define UDCCSR0_SST (1 << 4) /* Sent Stall */
-#define UDCCSR0_DME (1 << 3) /* DMA Enable */
-#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */
-#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */
-#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */
-
-#define UDCCSRA __REG(0x40600104) /* UDC Control/Status register - Endpoint A */
-#define UDCCSRB __REG(0x40600108) /* UDC Control/Status register - Endpoint B */
-#define UDCCSRC __REG(0x4060010C) /* UDC Control/Status register - Endpoint C */
-#define UDCCSRD __REG(0x40600110) /* UDC Control/Status register - Endpoint D */
-#define UDCCSRE __REG(0x40600114) /* UDC Control/Status register - Endpoint E */
-#define UDCCSRF __REG(0x40600118) /* UDC Control/Status register - Endpoint F */
-#define UDCCSRG __REG(0x4060011C) /* UDC Control/Status register - Endpoint G */
-#define UDCCSRH __REG(0x40600120) /* UDC Control/Status register - Endpoint H */
-#define UDCCSRI __REG(0x40600124) /* UDC Control/Status register - Endpoint I */
-#define UDCCSRJ __REG(0x40600128) /* UDC Control/Status register - Endpoint J */
-#define UDCCSRK __REG(0x4060012C) /* UDC Control/Status register - Endpoint K */
-#define UDCCSRL __REG(0x40600130) /* UDC Control/Status register - Endpoint L */
-#define UDCCSRM __REG(0x40600134) /* UDC Control/Status register - Endpoint M */
-#define UDCCSRN __REG(0x40600138) /* UDC Control/Status register - Endpoint N */
-#define UDCCSRP __REG(0x4060013C) /* UDC Control/Status register - Endpoint P */
-#define UDCCSRQ __REG(0x40600140) /* UDC Control/Status register - Endpoint Q */
-#define UDCCSRR __REG(0x40600144) /* UDC Control/Status register - Endpoint R */
-#define UDCCSRS __REG(0x40600148) /* UDC Control/Status register - Endpoint S */
-#define UDCCSRT __REG(0x4060014C) /* UDC Control/Status register - Endpoint T */
-#define UDCCSRU __REG(0x40600150) /* UDC Control/Status register - Endpoint U */
-#define UDCCSRV __REG(0x40600154) /* UDC Control/Status register - Endpoint V */
-#define UDCCSRW __REG(0x40600158) /* UDC Control/Status register - Endpoint W */
-#define UDCCSRX __REG(0x4060015C) /* UDC Control/Status register - Endpoint X */
-
-#define UDCCSR_DPE (1 << 9) /* Data Packet Error */
-#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */
-#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */
-#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */
-#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */
-#define UDCCSR_FST (1 << 5) /* Force STALL */
-#define UDCCSR_SST (1 << 4) /* Sent STALL */
-#define UDCCSR_DME (1 << 3) /* DMA Enable */
-#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */
-#define UDCCSR_PC (1 << 1) /* Packet Complete */
-#define UDCCSR_FS (1 << 0) /* FIFO needs service */
-
-#define UDCBCN(x) __REG2(0x40600200, (x)<<2)
-#define UDCBCR0 __REG(0x40600200) /* Byte Count Register - EP0 */
-#define UDCBCRA __REG(0x40600204) /* Byte Count Register - EPA */
-#define UDCBCRB __REG(0x40600208) /* Byte Count Register - EPB */
-#define UDCBCRC __REG(0x4060020C) /* Byte Count Register - EPC */
-#define UDCBCRD __REG(0x40600210) /* Byte Count Register - EPD */
-#define UDCBCRE __REG(0x40600214) /* Byte Count Register - EPE */
-#define UDCBCRF __REG(0x40600218) /* Byte Count Register - EPF */
-#define UDCBCRG __REG(0x4060021C) /* Byte Count Register - EPG */
-#define UDCBCRH __REG(0x40600220) /* Byte Count Register - EPH */
-#define UDCBCRI __REG(0x40600224) /* Byte Count Register - EPI */
-#define UDCBCRJ __REG(0x40600228) /* Byte Count Register - EPJ */
-#define UDCBCRK __REG(0x4060022C) /* Byte Count Register - EPK */
-#define UDCBCRL __REG(0x40600230) /* Byte Count Register - EPL */
-#define UDCBCRM __REG(0x40600234) /* Byte Count Register - EPM */
-#define UDCBCRN __REG(0x40600238) /* Byte Count Register - EPN */
-#define UDCBCRP __REG(0x4060023C) /* Byte Count Register - EPP */
-#define UDCBCRQ __REG(0x40600240) /* Byte Count Register - EPQ */
-#define UDCBCRR __REG(0x40600244) /* Byte Count Register - EPR */
-#define UDCBCRS __REG(0x40600248) /* Byte Count Register - EPS */
-#define UDCBCRT __REG(0x4060024C) /* Byte Count Register - EPT */
-#define UDCBCRU __REG(0x40600250) /* Byte Count Register - EPU */
-#define UDCBCRV __REG(0x40600254) /* Byte Count Register - EPV */
-#define UDCBCRW __REG(0x40600258) /* Byte Count Register - EPW */
-#define UDCBCRX __REG(0x4060025C) /* Byte Count Register - EPX */
-
-#define UDCDN(x) __REG2(0x40600300, (x)<<2)
-#define PHYS_UDCDN(x) (0x40600300 + ((x)<<2))
-#define PUDCDN(x) (volatile u32 *)(io_p2v(PHYS_UDCDN((x))))
-#define UDCDR0 __REG(0x40600300) /* Data Register - EP0 */
-#define UDCDRA __REG(0x40600304) /* Data Register - EPA */
-#define UDCDRB __REG(0x40600308) /* Data Register - EPB */
-#define UDCDRC __REG(0x4060030C) /* Data Register - EPC */
-#define UDCDRD __REG(0x40600310) /* Data Register - EPD */
-#define UDCDRE __REG(0x40600314) /* Data Register - EPE */
-#define UDCDRF __REG(0x40600318) /* Data Register - EPF */
-#define UDCDRG __REG(0x4060031C) /* Data Register - EPG */
-#define UDCDRH __REG(0x40600320) /* Data Register - EPH */
-#define UDCDRI __REG(0x40600324) /* Data Register - EPI */
-#define UDCDRJ __REG(0x40600328) /* Data Register - EPJ */
-#define UDCDRK __REG(0x4060032C) /* Data Register - EPK */
-#define UDCDRL __REG(0x40600330) /* Data Register - EPL */
-#define UDCDRM __REG(0x40600334) /* Data Register - EPM */
-#define UDCDRN __REG(0x40600338) /* Data Register - EPN */
-#define UDCDRP __REG(0x4060033C) /* Data Register - EPP */
-#define UDCDRQ __REG(0x40600340) /* Data Register - EPQ */
-#define UDCDRR __REG(0x40600344) /* Data Register - EPR */
-#define UDCDRS __REG(0x40600348) /* Data Register - EPS */
-#define UDCDRT __REG(0x4060034C) /* Data Register - EPT */
-#define UDCDRU __REG(0x40600350) /* Data Register - EPU */
-#define UDCDRV __REG(0x40600354) /* Data Register - EPV */
-#define UDCDRW __REG(0x40600358) /* Data Register - EPW */
-#define UDCDRX __REG(0x4060035C) /* Data Register - EPX */
-
-#define UDCCN(x) __REG2(0x40600400, (x)<<2)
-#define UDCCRA __REG(0x40600404) /* Configuration register EPA */
-#define UDCCRB __REG(0x40600408) /* Configuration register EPB */
-#define UDCCRC __REG(0x4060040C) /* Configuration register EPC */
-#define UDCCRD __REG(0x40600410) /* Configuration register EPD */
-#define UDCCRE __REG(0x40600414) /* Configuration register EPE */
-#define UDCCRF __REG(0x40600418) /* Configuration register EPF */
-#define UDCCRG __REG(0x4060041C) /* Configuration register EPG */
-#define UDCCRH __REG(0x40600420) /* Configuration register EPH */
-#define UDCCRI __REG(0x40600424) /* Configuration register EPI */
-#define UDCCRJ __REG(0x40600428) /* Configuration register EPJ */
-#define UDCCRK __REG(0x4060042C) /* Configuration register EPK */
-#define UDCCRL __REG(0x40600430) /* Configuration register EPL */
-#define UDCCRM __REG(0x40600434) /* Configuration register EPM */
-#define UDCCRN __REG(0x40600438) /* Configuration register EPN */
-#define UDCCRP __REG(0x4060043C) /* Configuration register EPP */
-#define UDCCRQ __REG(0x40600440) /* Configuration register EPQ */
-#define UDCCRR __REG(0x40600444) /* Configuration register EPR */
-#define UDCCRS __REG(0x40600448) /* Configuration register EPS */
-#define UDCCRT __REG(0x4060044C) /* Configuration register EPT */
-#define UDCCRU __REG(0x40600450) /* Configuration register EPU */
-#define UDCCRV __REG(0x40600454) /* Configuration register EPV */
-#define UDCCRW __REG(0x40600458) /* Configuration register EPW */
-#define UDCCRX __REG(0x4060045C) /* Configuration register EPX */
-
-#define UDCCONR_CN (0x03 << 25) /* Configuration Number */
-#define UDCCONR_CN_S (25)
-#define UDCCONR_IN (0x07 << 22) /* Interface Number */
-#define UDCCONR_IN_S (22)
-#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */
-#define UDCCONR_AISN_S (19)
-#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */
-#define UDCCONR_EN_S (15)
-#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */
-#define UDCCONR_ET_S (13)
-#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */
-#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */
-#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */
-#define UDCCONR_ET_NU (0x00 << 13) /* Not used */
-#define UDCCONR_ED (1 << 12) /* Endpoint Direction */
-#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */
-#define UDCCONR_MPS_S (2)
-#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */
-#define UDCCONR_EE (1 << 0) /* Endpoint Enable */
-
-
-#define UDC_INT_FIFOERROR (0x2)
-#define UDC_INT_PACKETCMP (0x1)
-
-#define UDC_FNR_MASK (0x7ff)
-
-#define UDCCSR_WR_MASK (UDCCSR_DME|UDCCSR_FST)
-#define UDC_BCR_MASK (0x3ff)
-#endif
-
-/*
* Fast Infrared Communication Port
*/
#define ICSR0 __REG(0x40800014) /* ICP Status Register 0 */
#define ICSR1 __REG(0x40800018) /* ICP Status Register 1 */
-#define ICCR0_AME (1 << 7) /* Adress match enable */
+#define ICCR0_AME (1 << 7) /* Address match enable */
#define ICCR0_TIE (1 << 6) /* Transmit FIFO interrupt enable */
#define ICCR0_RIE (1 << 5) /* Recieve FIFO interrupt enable */
#define ICCR0_RXE (1 << 4) /* Receive enable */
#define ICCR0_LBM (1 << 1) /* Loopback mode */
#define ICCR0_ITR (1 << 0) /* IrDA transmission */
-#ifdef CONFIG_PXA27x
#define ICCR2_RXP (1 << 3) /* Receive Pin Polarity select */
#define ICCR2_TXP (1 << 2) /* Transmit Pin Polarity select */
#define ICCR2_TRIG (3 << 0) /* Receive FIFO Trigger threshold */
#define ICCR2_TRIG_8 (0 << 0) /* >= 8 bytes */
#define ICCR2_TRIG_16 (1 << 0) /* >= 16 bytes */
#define ICCR2_TRIG_32 (2 << 0) /* >= 32 bytes */
-#endif
#ifdef CONFIG_PXA27x
#define ICSR0_EOC (1 << 6) /* DMA End of Descriptor Chain */
#define ICPR __REG(0x40D00010) /* Interrupt Controller Pending Register */
#define ICCR __REG(0x40D00014) /* Interrupt Controller Control Register */
+#define ICIP2 __REG(0x40D0009C) /* Interrupt Controller IRQ Pending Register 2 */
+#define ICMR2 __REG(0x40D000A0) /* Interrupt Controller Mask Register 2 */
+#define ICLR2 __REG(0x40D000A4) /* Interrupt Controller Level Register 2 */
+#define ICFP2 __REG(0x40D000A8) /* Interrupt Controller FIQ Pending Register 2 */
+#define ICPR2 __REG(0x40D000AC) /* Interrupt Controller Pending Register 2 */
/*
* General Purpose I/O
*/
+#define GPIO0_BASE ((void __iomem *)io_p2v(0x40E00000))
+#define GPIO1_BASE ((void __iomem *)io_p2v(0x40E00004))
+#define GPIO2_BASE ((void __iomem *)io_p2v(0x40E00008))
+#define GPIO3_BASE ((void __iomem *)io_p2v(0x40E00100))
+
+#define GPLR_OFFSET 0x00
+#define GPDR_OFFSET 0x0C
+#define GPSR_OFFSET 0x18
+#define GPCR_OFFSET 0x24
+#define GRER_OFFSET 0x30
+#define GFER_OFFSET 0x3C
+#define GEDR_OFFSET 0x48
+
#define GPLR0 __REG(0x40E00000) /* GPIO Pin-Level Register GPIO<31:0> */
#define GPLR1 __REG(0x40E00004) /* GPIO Pin-Level Register GPIO<63:32> */
#define GPLR2 __REG(0x40E00008) /* GPIO Pin-Level Register GPIO<80:64> */
#define GPIO_bit(x) (1 << ((x) & 0x1f))
-#ifdef CONFIG_PXA27x
+#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
/* Interrupt Controller */
-#define ICIP2 __REG(0x40D0009C) /* Interrupt Controller IRQ Pending Register 2 */
-#define ICMR2 __REG(0x40D000A0) /* Interrupt Controller Mask Register 2 */
-#define ICLR2 __REG(0x40D000A4) /* Interrupt Controller Level Register 2 */
-#define ICFP2 __REG(0x40D000A8) /* Interrupt Controller FIQ Pending Register 2 */
-#define ICPR2 __REG(0x40D000AC) /* Interrupt Controller Pending Register 2 */
-
#define _GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3)
#define _GPDR(x) __REG2(0x40E0000C, ((x) & 0x60) >> 3)
#define _GPSR(x) __REG2(0x40E00018, ((x) & 0x60) >> 3)
#endif
-
-/* GPIO alternate function assignments */
-
-#define GPIO1_RST 1 /* reset */
-#define GPIO6_MMCCLK 6 /* MMC Clock */
-#define GPIO7_48MHz 7 /* 48 MHz clock output */
-#define GPIO8_MMCCS0 8 /* MMC Chip Select 0 */
-#define GPIO9_MMCCS1 9 /* MMC Chip Select 1 */
-#define GPIO10_RTCCLK 10 /* real time clock (1 Hz) */
-#define GPIO11_3_6MHz 11 /* 3.6 MHz oscillator out */
-#define GPIO12_32KHz 12 /* 32 kHz out */
-#define GPIO13_MBGNT 13 /* memory controller grant */
-#define GPIO14_MBREQ 14 /* alternate bus master request */
-#define GPIO15_nCS_1 15 /* chip select 1 */
-#define GPIO16_PWM0 16 /* PWM0 output */
-#define GPIO17_PWM1 17 /* PWM1 output */
-#define GPIO18_RDY 18 /* Ext. Bus Ready */
-#define GPIO19_DREQ1 19 /* External DMA Request */
-#define GPIO20_DREQ0 20 /* External DMA Request */
-#define GPIO23_SCLK 23 /* SSP clock */
-#define GPIO24_SFRM 24 /* SSP Frame */
-#define GPIO25_STXD 25 /* SSP transmit */
-#define GPIO26_SRXD 26 /* SSP receive */
-#define GPIO27_SEXTCLK 27 /* SSP ext_clk */
-#define GPIO28_BITCLK 28 /* AC97/I2S bit_clk */
-#define GPIO29_SDATA_IN 29 /* AC97 Sdata_in0 / I2S Sdata_in */
-#define GPIO30_SDATA_OUT 30 /* AC97/I2S Sdata_out */
-#define GPIO31_SYNC 31 /* AC97/I2S sync */
-#define GPIO32_SDATA_IN1 32 /* AC97 Sdata_in1 */
-#define GPIO32_SYSCLK 32 /* I2S System Clock */
-#define GPIO32_MMCCLK 32 /* MMC Clock (PXA270) */
-#define GPIO33_nCS_5 33 /* chip select 5 */
-#define GPIO34_FFRXD 34 /* FFUART receive */
-#define GPIO34_MMCCS0 34 /* MMC Chip Select 0 */
-#define GPIO35_FFCTS 35 /* FFUART Clear to send */
-#define GPIO36_FFDCD 36 /* FFUART Data carrier detect */
-#define GPIO37_FFDSR 37 /* FFUART data set ready */
-#define GPIO38_FFRI 38 /* FFUART Ring Indicator */
-#define GPIO39_MMCCS1 39 /* MMC Chip Select 1 */
-#define GPIO39_FFTXD 39 /* FFUART transmit data */
-#define GPIO40_FFDTR 40 /* FFUART data terminal Ready */
-#define GPIO41_FFRTS 41 /* FFUART request to send */
-#define GPIO42_BTRXD 42 /* BTUART receive data */
-#define GPIO43_BTTXD 43 /* BTUART transmit data */
-#define GPIO44_BTCTS 44 /* BTUART clear to send */
-#define GPIO45_BTRTS 45 /* BTUART request to send */
-#define GPIO45_AC97_SYSCLK 45 /* AC97 System Clock */
-#define GPIO46_ICPRXD 46 /* ICP receive data */
-#define GPIO46_STRXD 46 /* STD_UART receive data */
-#define GPIO47_ICPTXD 47 /* ICP transmit data */
-#define GPIO47_STTXD 47 /* STD_UART transmit data */
-#define GPIO48_nPOE 48 /* Output Enable for Card Space */
-#define GPIO49_nPWE 49 /* Write Enable for Card Space */
-#define GPIO50_nPIOR 50 /* I/O Read for Card Space */
-#define GPIO51_nPIOW 51 /* I/O Write for Card Space */
-#define GPIO52_nPCE_1 52 /* Card Enable for Card Space */
-#define GPIO53_nPCE_2 53 /* Card Enable for Card Space */
-#define GPIO53_MMCCLK 53 /* MMC Clock */
-#define GPIO54_MMCCLK 54 /* MMC Clock */
-#define GPIO54_pSKTSEL 54 /* Socket Select for Card Space */
-#define GPIO54_nPCE_2 54 /* Card Enable for Card Space (PXA27x) */
-#define GPIO55_nPREG 55 /* Card Address bit 26 */
-#define GPIO56_nPWAIT 56 /* Wait signal for Card Space */
-#define GPIO57_nIOIS16 57 /* Bus Width select for I/O Card Space */
-#define GPIO58_LDD_0 58 /* LCD data pin 0 */
-#define GPIO59_LDD_1 59 /* LCD data pin 1 */
-#define GPIO60_LDD_2 60 /* LCD data pin 2 */
-#define GPIO61_LDD_3 61 /* LCD data pin 3 */
-#define GPIO62_LDD_4 62 /* LCD data pin 4 */
-#define GPIO63_LDD_5 63 /* LCD data pin 5 */
-#define GPIO64_LDD_6 64 /* LCD data pin 6 */
-#define GPIO65_LDD_7 65 /* LCD data pin 7 */
-#define GPIO66_LDD_8 66 /* LCD data pin 8 */
-#define GPIO66_MBREQ 66 /* alternate bus master req */
-#define GPIO67_LDD_9 67 /* LCD data pin 9 */
-#define GPIO67_MMCCS0 67 /* MMC Chip Select 0 */
-#define GPIO68_LDD_10 68 /* LCD data pin 10 */
-#define GPIO68_MMCCS1 68 /* MMC Chip Select 1 */
-#define GPIO69_LDD_11 69 /* LCD data pin 11 */
-#define GPIO69_MMCCLK 69 /* MMC_CLK */
-#define GPIO70_LDD_12 70 /* LCD data pin 12 */
-#define GPIO70_RTCCLK 70 /* Real Time clock (1 Hz) */
-#define GPIO71_LDD_13 71 /* LCD data pin 13 */
-#define GPIO71_3_6MHz 71 /* 3.6 MHz Oscillator clock */
-#define GPIO72_LDD_14 72 /* LCD data pin 14 */
-#define GPIO72_32kHz 72 /* 32 kHz clock */
-#define GPIO73_LDD_15 73 /* LCD data pin 15 */
-#define GPIO73_MBGNT 73 /* Memory controller grant */
-#define GPIO74_LCD_FCLK 74 /* LCD Frame clock */
-#define GPIO75_LCD_LCLK 75 /* LCD line clock */
-#define GPIO76_LCD_PCLK 76 /* LCD Pixel clock */
-#define GPIO77_LCD_ACBIAS 77 /* LCD AC Bias */
-#define GPIO78_nCS_2 78 /* chip select 2 */
-#define GPIO79_nCS_3 79 /* chip select 3 */
-#define GPIO80_nCS_4 80 /* chip select 4 */
-#define GPIO81_NSCLK 81 /* NSSP clock */
-#define GPIO82_NSFRM 82 /* NSSP Frame */
-#define GPIO83_NSTXD 83 /* NSSP transmit */
-#define GPIO84_NSRXD 84 /* NSSP receive */
-#define GPIO85_nPCE_1 85 /* Card Enable for Card Space (PXA27x) */
-#define GPIO92_MMCDAT0 92 /* MMC DAT0 (PXA27x) */
-#define GPIO109_MMCDAT1 109 /* MMC DAT1 (PXA27x) */
-#define GPIO110_MMCDAT2 110 /* MMC DAT2 (PXA27x) */
-#define GPIO110_MMCCS0 110 /* MMC Chip Select 0 (PXA27x) */
-#define GPIO111_MMCDAT3 111 /* MMC DAT3 (PXA27x) */
-#define GPIO111_MMCCS1 111 /* MMC Chip Select 1 (PXA27x) */
-#define GPIO112_MMCCMD 112 /* MMC CMD (PXA27x) */
-#define GPIO113_I2S_SYSCLK 113 /* I2S System Clock (PXA27x) */
-#define GPIO113_AC97_RESET_N 113 /* AC97 NRESET on (PXA27x) */
-
-/* GPIO alternate function mode & direction */
-
-#define GPIO_IN 0x000
-#define GPIO_OUT 0x080
-#define GPIO_ALT_FN_1_IN 0x100
-#define GPIO_ALT_FN_1_OUT 0x180
-#define GPIO_ALT_FN_2_IN 0x200
-#define GPIO_ALT_FN_2_OUT 0x280
-#define GPIO_ALT_FN_3_IN 0x300
-#define GPIO_ALT_FN_3_OUT 0x380
-#define GPIO_MD_MASK_NR 0x07f
-#define GPIO_MD_MASK_DIR 0x080
-#define GPIO_MD_MASK_FN 0x300
-#define GPIO_DFLT_LOW 0x400
-#define GPIO_DFLT_HIGH 0x800
-
-#define GPIO1_RTS_MD ( 1 | GPIO_ALT_FN_1_IN)
-#define GPIO6_MMCCLK_MD ( 6 | GPIO_ALT_FN_1_OUT)
-#define GPIO7_48MHz_MD ( 7 | GPIO_ALT_FN_1_OUT)
-#define GPIO8_MMCCS0_MD ( 8 | GPIO_ALT_FN_1_OUT)
-#define GPIO9_MMCCS1_MD ( 9 | GPIO_ALT_FN_1_OUT)
-#define GPIO10_RTCCLK_MD (10 | GPIO_ALT_FN_1_OUT)
-#define GPIO11_3_6MHz_MD (11 | GPIO_ALT_FN_1_OUT)
-#define GPIO12_32KHz_MD (12 | GPIO_ALT_FN_1_OUT)
-#define GPIO13_MBGNT_MD (13 | GPIO_ALT_FN_2_OUT)
-#define GPIO14_MBREQ_MD (14 | GPIO_ALT_FN_1_IN)
-#define GPIO15_nCS_1_MD (15 | GPIO_ALT_FN_2_OUT)
-#define GPIO16_PWM0_MD (16 | GPIO_ALT_FN_2_OUT)
-#define GPIO17_PWM1_MD (17 | GPIO_ALT_FN_2_OUT)
-#define GPIO18_RDY_MD (18 | GPIO_ALT_FN_1_IN)
-#define GPIO19_DREQ1_MD (19 | GPIO_ALT_FN_1_IN)
-#define GPIO20_DREQ0_MD (20 | GPIO_ALT_FN_1_IN)
-#define GPIO23_SCLK_MD (23 | GPIO_ALT_FN_2_OUT)
-#define GPIO24_SFRM_MD (24 | GPIO_ALT_FN_2_OUT)
-#define GPIO25_STXD_MD (25 | GPIO_ALT_FN_2_OUT)
-#define GPIO26_SRXD_MD (26 | GPIO_ALT_FN_1_IN)
-#define GPIO27_SEXTCLK_MD (27 | GPIO_ALT_FN_1_IN)
-#define GPIO28_BITCLK_AC97_MD (28 | GPIO_ALT_FN_1_IN)
-#define GPIO28_BITCLK_IN_I2S_MD (28 | GPIO_ALT_FN_2_IN)
-#define GPIO28_BITCLK_OUT_I2S_MD (28 | GPIO_ALT_FN_1_OUT)
-#define GPIO29_SDATA_IN_AC97_MD (29 | GPIO_ALT_FN_1_IN)
-#define GPIO29_SDATA_IN_I2S_MD (29 | GPIO_ALT_FN_2_IN)
-#define GPIO30_SDATA_OUT_AC97_MD (30 | GPIO_ALT_FN_2_OUT)
-#define GPIO30_SDATA_OUT_I2S_MD (30 | GPIO_ALT_FN_1_OUT)
-#define GPIO31_SYNC_I2S_MD (31 | GPIO_ALT_FN_1_OUT)
-#define GPIO31_SYNC_AC97_MD (31 | GPIO_ALT_FN_2_OUT)
-#define GPIO32_SDATA_IN1_AC97_MD (32 | GPIO_ALT_FN_1_IN)
-#define GPIO32_SYSCLK_I2S_MD (32 | GPIO_ALT_FN_1_OUT)
-#define GPIO32_MMCCLK_MD ( 32 | GPIO_ALT_FN_2_OUT)
-#define GPIO33_nCS_5_MD (33 | GPIO_ALT_FN_2_OUT)
-#define GPIO34_FFRXD_MD (34 | GPIO_ALT_FN_1_IN)
-#define GPIO34_MMCCS0_MD (34 | GPIO_ALT_FN_2_OUT)
-#define GPIO35_FFCTS_MD (35 | GPIO_ALT_FN_1_IN)
-#define GPIO36_FFDCD_MD (36 | GPIO_ALT_FN_1_IN)
-#define GPIO37_FFDSR_MD (37 | GPIO_ALT_FN_1_IN)
-#define GPIO38_FFRI_MD (38 | GPIO_ALT_FN_1_IN)
-#define GPIO39_MMCCS1_MD (39 | GPIO_ALT_FN_1_OUT)
-#define GPIO39_FFTXD_MD (39 | GPIO_ALT_FN_2_OUT)
-#define GPIO40_FFDTR_MD (40 | GPIO_ALT_FN_2_OUT)
-#define GPIO41_FFRTS_MD (41 | GPIO_ALT_FN_2_OUT)
-#define GPIO42_BTRXD_MD (42 | GPIO_ALT_FN_1_IN)
-#define GPIO43_BTTXD_MD (43 | GPIO_ALT_FN_2_OUT)
-#define GPIO44_BTCTS_MD (44 | GPIO_ALT_FN_1_IN)
-#define GPIO45_BTRTS_MD (45 | GPIO_ALT_FN_2_OUT)
-#define GPIO45_SYSCLK_AC97_MD (45 | GPIO_ALT_FN_1_OUT)
-#define GPIO46_ICPRXD_MD (46 | GPIO_ALT_FN_1_IN)
-#define GPIO46_STRXD_MD (46 | GPIO_ALT_FN_2_IN)
-#define GPIO47_ICPTXD_MD (47 | GPIO_ALT_FN_2_OUT)
-#define GPIO47_STTXD_MD (47 | GPIO_ALT_FN_1_OUT)
-#define GPIO48_nPOE_MD (48 | GPIO_ALT_FN_2_OUT)
-#define GPIO49_nPWE_MD (49 | GPIO_ALT_FN_2_OUT)
-#define GPIO50_nPIOR_MD (50 | GPIO_ALT_FN_2_OUT)
-#define GPIO51_nPIOW_MD (51 | GPIO_ALT_FN_2_OUT)
-#define GPIO52_nPCE_1_MD (52 | GPIO_ALT_FN_2_OUT)
-#define GPIO53_nPCE_2_MD (53 | GPIO_ALT_FN_2_OUT)
-#define GPIO53_MMCCLK_MD (53 | GPIO_ALT_FN_1_OUT)
-#define GPIO54_MMCCLK_MD (54 | GPIO_ALT_FN_1_OUT)
-#define GPIO54_nPCE_2_MD (54 | GPIO_ALT_FN_2_OUT)
-#define GPIO54_pSKTSEL_MD (54 | GPIO_ALT_FN_2_OUT)
-#define GPIO55_nPREG_MD (55 | GPIO_ALT_FN_2_OUT)
-#define GPIO56_nPWAIT_MD (56 | GPIO_ALT_FN_1_IN)
-#define GPIO57_nIOIS16_MD (57 | GPIO_ALT_FN_1_IN)
-#define GPIO58_LDD_0_MD (58 | GPIO_ALT_FN_2_OUT)
-#define GPIO59_LDD_1_MD (59 | GPIO_ALT_FN_2_OUT)
-#define GPIO60_LDD_2_MD (60 | GPIO_ALT_FN_2_OUT)
-#define GPIO61_LDD_3_MD (61 | GPIO_ALT_FN_2_OUT)
-#define GPIO62_LDD_4_MD (62 | GPIO_ALT_FN_2_OUT)
-#define GPIO63_LDD_5_MD (63 | GPIO_ALT_FN_2_OUT)
-#define GPIO64_LDD_6_MD (64 | GPIO_ALT_FN_2_OUT)
-#define GPIO65_LDD_7_MD (65 | GPIO_ALT_FN_2_OUT)
-#define GPIO66_LDD_8_MD (66 | GPIO_ALT_FN_2_OUT)
-#define GPIO66_MBREQ_MD (66 | GPIO_ALT_FN_1_IN)
-#define GPIO67_LDD_9_MD (67 | GPIO_ALT_FN_2_OUT)
-#define GPIO67_MMCCS0_MD (67 | GPIO_ALT_FN_1_OUT)
-#define GPIO68_LDD_10_MD (68 | GPIO_ALT_FN_2_OUT)
-#define GPIO68_MMCCS1_MD (68 | GPIO_ALT_FN_1_OUT)
-#define GPIO69_LDD_11_MD (69 | GPIO_ALT_FN_2_OUT)
-#define GPIO69_MMCCLK_MD (69 | GPIO_ALT_FN_1_OUT)
-#define GPIO70_LDD_12_MD (70 | GPIO_ALT_FN_2_OUT)
-#define GPIO70_RTCCLK_MD (70 | GPIO_ALT_FN_1_OUT)
-#define GPIO71_LDD_13_MD (71 | GPIO_ALT_FN_2_OUT)
-#define GPIO71_3_6MHz_MD (71 | GPIO_ALT_FN_1_OUT)
-#define GPIO72_LDD_14_MD (72 | GPIO_ALT_FN_2_OUT)
-#define GPIO72_32kHz_MD (72 | GPIO_ALT_FN_1_OUT)
-#define GPIO73_LDD_15_MD (73 | GPIO_ALT_FN_2_OUT)
-#define GPIO73_MBGNT_MD (73 | GPIO_ALT_FN_1_OUT)
-#define GPIO74_LCD_FCLK_MD (74 | GPIO_ALT_FN_2_OUT)
-#define GPIO75_LCD_LCLK_MD (75 | GPIO_ALT_FN_2_OUT)
-#define GPIO76_LCD_PCLK_MD (76 | GPIO_ALT_FN_2_OUT)
-#define GPIO77_LCD_ACBIAS_MD (77 | GPIO_ALT_FN_2_OUT)
-#define GPIO78_nCS_2_MD (78 | GPIO_ALT_FN_2_OUT)
-#define GPIO79_nCS_3_MD (79 | GPIO_ALT_FN_2_OUT)
-#define GPIO79_pSKTSEL_MD (79 | GPIO_ALT_FN_1_OUT)
-#define GPIO80_nCS_4_MD (80 | GPIO_ALT_FN_2_OUT)
-#define GPIO81_NSSP_CLK_OUT (81 | GPIO_ALT_FN_1_OUT)
-#define GPIO81_NSSP_CLK_IN (81 | GPIO_ALT_FN_1_IN)
-#define GPIO82_NSSP_FRM_OUT (82 | GPIO_ALT_FN_1_OUT)
-#define GPIO82_NSSP_FRM_IN (82 | GPIO_ALT_FN_1_IN)
-#define GPIO83_NSSP_TX (83 | GPIO_ALT_FN_1_OUT)
-#define GPIO83_NSSP_RX (83 | GPIO_ALT_FN_2_IN)
-#define GPIO84_NSSP_TX (84 | GPIO_ALT_FN_1_OUT)
-#define GPIO84_NSSP_RX (84 | GPIO_ALT_FN_2_IN)
-#define GPIO85_nPCE_1_MD (85 | GPIO_ALT_FN_1_OUT)
-#define GPIO92_MMCDAT0_MD (92 | GPIO_ALT_FN_1_OUT)
-#define GPIO109_MMCDAT1_MD (109 | GPIO_ALT_FN_1_OUT)
-#define GPIO110_MMCDAT2_MD (110 | GPIO_ALT_FN_1_OUT)
-#define GPIO110_MMCCS0_MD (110 | GPIO_ALT_FN_1_OUT)
-#define GPIO111_MMCDAT3_MD (111 | GPIO_ALT_FN_1_OUT)
-#define GPIO110_MMCCS1_MD (111 | GPIO_ALT_FN_1_OUT)
-#define GPIO112_MMCCMD_MD (112 | GPIO_ALT_FN_1_OUT)
-#define GPIO113_I2S_SYSCLK_MD (113 | GPIO_ALT_FN_1_OUT)
-#define GPIO113_AC97_RESET_N_MD (113 | GPIO_ALT_FN_2_OUT)
-#define GPIO117_I2CSCL_MD (117 | GPIO_ALT_FN_1_OUT)
-#define GPIO118_I2CSDA_MD (118 | GPIO_ALT_FN_1_IN)
-
/*
* Power Manager
*/
#define PSSR_OTGPH (1 << 6) /* OTG Peripheral control Hold */
#define PSSR_RDH (1 << 5) /* Read Disable Hold */
#define PSSR_PH (1 << 4) /* Peripheral Control Hold */
+#define PSSR_STS (1 << 3) /* Standby Mode Status */
#define PSSR_VFS (1 << 2) /* VDD Fault Status */
#define PSSR_BFS (1 << 1) /* Battery Fault Status */
#define PSSR_SSS (1 << 0) /* Software Sleep Status */
+#define PSLR_SL_ROD (1 << 20) /* Sleep-Mode/Depp-Sleep Mode nRESET_OUT Disable */
+
#define PCFR_RO (1 << 15) /* RDH Override */
#define PCFR_PO (1 << 14) /* PH Override */
#define PCFR_GPROD (1 << 12) /* GPIO nRESET_OUT Disable */
#define PCFR_FVC (1 << 10) /* Frequency/Voltage Change */
#define PCFR_DC_EN (1 << 7) /* Sleep/deep-sleep DC-DC Converter Enable */
#define PCFR_PI2CEN (1 << 6) /* Enable PI2C controller */
+#define PCFR_GPR_EN (1 << 4) /* nRESET_GPIO Pin Enable */
#define PCFR_DS (1 << 3) /* Deep Sleep Mode */
#define PCFR_FS (1 << 2) /* Float Static Chip Selects */
#define PCFR_FP (1 << 1) /* Float PCMCIA controls */
#define PWER_GPIO15 PWER_GPIO (15) /* GPIO [15] wake-up enable */
#define PWER_RTC 0x80000000 /* RTC alarm wake-up enable */
-
/*
- * SSP Serial Port Registers
- * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
- * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
+ * SSP Serial Port Registers - see include/asm-arm/arch-pxa/regs-ssp.h
*/
- /* Common PXA2xx bits first */
-#define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */
-#define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */
-#define SSCR0_FRF (0x00000030) /* FRame Format (mask) */
-#define SSCR0_Motorola (0x0 << 4) /* Motorola's Serial Peripheral Interface (SPI) */
-#define SSCR0_TI (0x1 << 4) /* Texas Instruments' Synchronous Serial Protocol (SSP) */
-#define SSCR0_National (0x2 << 4) /* National Microwire */
-#define SSCR0_ECS (1 << 6) /* External clock select */
-#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */
-#define SSCR0_SCR (0x0000ff00) /* Serial Clock Rate (mask) */
-#define SSCR0_SerClkDiv(x) ((((x) - 2)/2) << 8) /* Divisor [2..512] */
-
-#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */
-#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */
-#define SSCR1_LBM (1 << 2) /* Loop-Back Mode */
-#define SSCR1_SPO (1 << 3) /* Motorola SPI SSPSCLK polarity setting */
-#define SSCR1_SPH (1 << 4) /* Motorola SPI SSPSCLK phase setting */
-#define SSCR1_MWDS (1 << 5) /* Microwire Transmit Data Size */
-#define SSCR1_TFT (0x000003c0) /* Transmit FIFO Threshold (mask) */
-#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
-#define SSCR1_RFT (0x00003c00) /* Receive FIFO Threshold (mask) */
-#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
-
-#define SSSR_TNF (1 << 2) /* Transmit FIFO Not Full */
-#define SSSR_RNE (1 << 3) /* Receive FIFO Not Empty */
-#define SSSR_BSY (1 << 4) /* SSP Busy */
-#define SSSR_TFS (1 << 5) /* Transmit FIFO Service Request */
-#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */
-#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */
-
-#define SSCR0_TIM (1 << 23) /* Transmit FIFO Under Run Interrupt Mask */
-#define SSCR0_RIM (1 << 22) /* Receive FIFO Over Run interrupt Mask */
-#define SSCR0_NCS (1 << 21) /* Network Clock Select */
-#define SSCR0_EDSS (1 << 20) /* Extended Data Size Select */
-
-/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
-#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */
-#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */
-#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */
-#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */
-#define SSCR1_SCFR (1 << 28) /* Slave Clock free Running */
-#define SSCR1_ECRA (1 << 27) /* Enable Clock Request A */
-#define SSCR1_ECRB (1 << 26) /* Enable Clock request B */
-#define SSCR1_SCLKDIR (1 << 25) /* Serial Bit Rate Clock Direction */
-#define SSCR1_SFRMDIR (1 << 24) /* Frame Direction */
-#define SSCR1_RWOT (1 << 23) /* Receive Without Transmit */
-#define SSCR1_TRAIL (1 << 22) /* Trailing Byte */
-#define SSCR1_TSRE (1 << 21) /* Transmit Service Request Enable */
-#define SSCR1_RSRE (1 << 20) /* Receive Service Request Enable */
-#define SSCR1_TINTE (1 << 19) /* Receiver Time-out Interrupt enable */
-#define SSCR1_PINTE (1 << 18) /* Peripheral Trailing Byte Interupt Enable */
-#define SSCR1_STRF (1 << 15) /* Select FIFO or EFWR */
-#define SSCR1_EFWR (1 << 14) /* Enable FIFO Write/Read */
-
-#define SSSR_BCE (1 << 23) /* Bit Count Error */
-#define SSSR_CSS (1 << 22) /* Clock Synchronisation Status */
-#define SSSR_TUR (1 << 21) /* Transmit FIFO Under Run */
-#define SSSR_EOC (1 << 20) /* End Of Chain */
-#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */
-#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */
-
-#define SSPSP_DMYSTOP(x) (x << 23) /* Dummy Stop */
-#define SSPSP_SFRMWDTH(x) (x << 16) /* Serial Frame Width */
-#define SSPSP_SFRMDLY(x) (x << 9) /* Serial Frame Delay */
-#define SSPSP_DMYSTRT(x) (x << 7) /* Dummy Start */
-#define SSPSP_STRTDLY(x) (x << 4) /* Start Delay */
-#define SSPSP_ETDS (1 << 3) /* End of Transfer data State */
-#define SSPSP_SFRMP (1 << 2) /* Serial Frame Polarity */
-#define SSPSP_SCMODE(x) (x << 0) /* Serial Bit Rate Clock Mode */
-
-
-#define SSCR0_P1 __REG(0x41000000) /* SSP Port 1 Control Register 0 */
-#define SSCR1_P1 __REG(0x41000004) /* SSP Port 1 Control Register 1 */
-#define SSSR_P1 __REG(0x41000008) /* SSP Port 1 Status Register */
-#define SSITR_P1 __REG(0x4100000C) /* SSP Port 1 Interrupt Test Register */
-#define SSDR_P1 __REG(0x41000010) /* (Write / Read) SSP Port 1 Data Write Register/SSP Data Read Register */
-
-/* Support existing PXA25x drivers */
-#define SSCR0 SSCR0_P1 /* SSP Control Register 0 */
-#define SSCR1 SSCR1_P1 /* SSP Control Register 1 */
-#define SSSR SSSR_P1 /* SSP Status Register */
-#define SSITR SSITR_P1 /* SSP Interrupt Test Register */
-#define SSDR SSDR_P1 /* (Write / Read) SSP Data Write Register/SSP Data Read Register */
-
-/* PXA27x ports */
-#if defined (CONFIG_PXA27x)
-#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
-#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
-#define SSCR0_P2 __REG(0x41700000) /* SSP Port 2 Control Register 0 */
-#define SSCR1_P2 __REG(0x41700004) /* SSP Port 2 Control Register 1 */
-#define SSSR_P2 __REG(0x41700008) /* SSP Port 2 Status Register */
-#define SSITR_P2 __REG(0x4170000C) /* SSP Port 2 Interrupt Test Register */
-#define SSDR_P2 __REG(0x41700010) /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
-#define SSTO_P2 __REG(0x41700028) /* SSP Port 2 Time Out Register */
-#define SSPSP_P2 __REG(0x4170002C) /* SSP Port 2 Programmable Serial Protocol */
-#define SSCR0_P3 __REG(0x41900000) /* SSP Port 3 Control Register 0 */
-#define SSCR1_P3 __REG(0x41900004) /* SSP Port 3 Control Register 1 */
-#define SSSR_P3 __REG(0x41900008) /* SSP Port 3 Status Register */
-#define SSITR_P3 __REG(0x4190000C) /* SSP Port 3 Interrupt Test Register */
-#define SSDR_P3 __REG(0x41900010) /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
-#define SSTO_P3 __REG(0x41900028) /* SSP Port 3 Time Out Register */
-#define SSPSP_P3 __REG(0x4190002C) /* SSP Port 3 Programmable Serial Protocol */
-#else /* PXA255 (only port 2) and PXA26x ports*/
-#define SSTO_P1 __REG(0x41000028) /* SSP Port 1 Time Out Register */
-#define SSPSP_P1 __REG(0x4100002C) /* SSP Port 1 Programmable Serial Protocol */
-#define SSCR0_P2 __REG(0x41400000) /* SSP Port 2 Control Register 0 */
-#define SSCR1_P2 __REG(0x41400004) /* SSP Port 2 Control Register 1 */
-#define SSSR_P2 __REG(0x41400008) /* SSP Port 2 Status Register */
-#define SSITR_P2 __REG(0x4140000C) /* SSP Port 2 Interrupt Test Register */
-#define SSDR_P2 __REG(0x41400010) /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
-#define SSTO_P2 __REG(0x41400028) /* SSP Port 2 Time Out Register */
-#define SSPSP_P2 __REG(0x4140002C) /* SSP Port 2 Programmable Serial Protocol */
-#define SSCR0_P3 __REG(0x41500000) /* SSP Port 3 Control Register 0 */
-#define SSCR1_P3 __REG(0x41500004) /* SSP Port 3 Control Register 1 */
-#define SSSR_P3 __REG(0x41500008) /* SSP Port 3 Status Register */
-#define SSITR_P3 __REG(0x4150000C) /* SSP Port 3 Interrupt Test Register */
-#define SSDR_P3 __REG(0x41500010) /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
-#define SSTO_P3 __REG(0x41500028) /* SSP Port 3 Time Out Register */
-#define SSPSP_P3 __REG(0x4150002C) /* SSP Port 3 Programmable Serial Protocol */
-#endif
-
-#define SSCR0_P(x) (*(((x) == 1) ? &SSCR0_P1 : ((x) == 2) ? &SSCR0_P2 : ((x) == 3) ? &SSCR0_P3 : NULL))
-#define SSCR1_P(x) (*(((x) == 1) ? &SSCR1_P1 : ((x) == 2) ? &SSCR1_P2 : ((x) == 3) ? &SSCR1_P3 : NULL))
-#define SSSR_P(x) (*(((x) == 1) ? &SSSR_P1 : ((x) == 2) ? &SSSR_P2 : ((x) == 3) ? &SSSR_P3 : NULL))
-#define SSITR_P(x) (*(((x) == 1) ? &SSITR_P1 : ((x) == 2) ? &SSITR_P2 : ((x) == 3) ? &SSITR_P3 : NULL))
-#define SSDR_P(x) (*(((x) == 1) ? &SSDR_P1 : ((x) == 2) ? &SSDR_P2 : ((x) == 3) ? &SSDR_P3 : NULL))
-#define SSTO_P(x) (*(((x) == 1) ? &SSTO_P1 : ((x) == 2) ? &SSTO_P2 : ((x) == 3) ? &SSTO_P3 : NULL))
-#define SSPSP_P(x) (*(((x) == 1) ? &SSPSP_P1 : ((x) == 2) ? &SSPSP_P2 : ((x) == 3) ? &SSPSP_P3 : NULL))
-
/*
- * MultiMediaCard (MMC) controller
+ * MultiMediaCard (MMC) controller - see drivers/mmc/host/pxamci.h
*/
-#define MMC_STRPCL __REG(0x41100000) /* Control to start and stop MMC clock */
-#define MMC_STAT __REG(0x41100004) /* MMC Status Register (read only) */
-#define MMC_CLKRT __REG(0x41100008) /* MMC clock rate */
-#define MMC_SPI __REG(0x4110000c) /* SPI mode control bits */
-#define MMC_CMDAT __REG(0x41100010) /* Command/response/data sequence control */
-#define MMC_RESTO __REG(0x41100014) /* Expected response time out */
-#define MMC_RDTO __REG(0x41100018) /* Expected data read time out */
-#define MMC_BLKLEN __REG(0x4110001c) /* Block length of data transaction */
-#define MMC_NOB __REG(0x41100020) /* Number of blocks, for block mode */
-#define MMC_PRTBUF __REG(0x41100024) /* Partial MMC_TXFIFO FIFO written */
-#define MMC_I_MASK __REG(0x41100028) /* Interrupt Mask */
-#define MMC_I_REG __REG(0x4110002c) /* Interrupt Register (read only) */
-#define MMC_CMD __REG(0x41100030) /* Index of current command */
-#define MMC_ARGH __REG(0x41100034) /* MSW part of the current command argument */
-#define MMC_ARGL __REG(0x41100038) /* LSW part of the current command argument */
-#define MMC_RES __REG(0x4110003c) /* Response FIFO (read only) */
-#define MMC_RXFIFO __REG(0x41100040) /* Receive FIFO (read only) */
-#define MMC_TXFIFO __REG(0x41100044) /* Transmit FIFO (write only) */
-
-
/*
* Core Clock
*/
#define CCCR_M_MASK 0x0060 /* Memory Frequency to Run Mode Frequency Multiplier */
#define CCCR_L_MASK 0x001f /* Crystal Frequency to Memory Frequency Multiplier */
-#define CKEN24_CAMERA (1 << 24) /* Camera Interface Clock Enable */
-#define CKEN23_SSP1 (1 << 23) /* SSP1 Unit Clock Enable */
-#define CKEN22_MEMC (1 << 22) /* Memory Controller Clock Enable */
-#define CKEN21_MEMSTK (1 << 21) /* Memory Stick Host Controller */
-#define CKEN20_IM (1 << 20) /* Internal Memory Clock Enable */
-#define CKEN19_KEYPAD (1 << 19) /* Keypad Interface Clock Enable */
-#define CKEN18_USIM (1 << 18) /* USIM Unit Clock Enable */
-#define CKEN17_MSL (1 << 17) /* MSL Unit Clock Enable */
-#define CKEN16_LCD (1 << 16) /* LCD Unit Clock Enable */
-#define CKEN15_PWRI2C (1 << 15) /* PWR I2C Unit Clock Enable */
-#define CKEN14_I2C (1 << 14) /* I2C Unit Clock Enable */
-#define CKEN13_FICP (1 << 13) /* FICP Unit Clock Enable */
-#define CKEN12_MMC (1 << 12) /* MMC Unit Clock Enable */
-#define CKEN11_USB (1 << 11) /* USB Unit Clock Enable */
-#define CKEN10_ASSP (1 << 10) /* ASSP (SSP3) Clock Enable */
-#define CKEN10_USBHOST (1 << 10) /* USB Host Unit Clock Enable */
-#define CKEN9_OSTIMER (1 << 9) /* OS Timer Unit Clock Enable */
-#define CKEN9_NSSP (1 << 9) /* NSSP (SSP2) Clock Enable */
-#define CKEN8_I2S (1 << 8) /* I2S Unit Clock Enable */
-#define CKEN7_BTUART (1 << 7) /* BTUART Unit Clock Enable */
-#define CKEN6_FFUART (1 << 6) /* FFUART Unit Clock Enable */
-#define CKEN5_STUART (1 << 5) /* STUART Unit Clock Enable */
-#define CKEN4_SSP3 (1 << 4) /* SSP3 Unit Clock Enable */
-#define CKEN3_SSP (1 << 3) /* SSP Unit Clock Enable */
-#define CKEN3_SSP2 (1 << 3) /* SSP2 Unit Clock Enable */
-#define CKEN2_AC97 (1 << 2) /* AC97 Unit Clock Enable */
-#define CKEN1_PWM1 (1 << 1) /* PWM1 Clock Enable */
-#define CKEN0_PWM0 (1 << 0) /* PWM0 Clock Enable */
+#define CKEN_AC97CONF (31) /* AC97 Controller Configuration */
+#define CKEN_CAMERA (24) /* Camera Interface Clock Enable */
+#define CKEN_SSP1 (23) /* SSP1 Unit Clock Enable */
+#define CKEN_MEMC (22) /* Memory Controller Clock Enable */
+#define CKEN_MEMSTK (21) /* Memory Stick Host Controller */
+#define CKEN_IM (20) /* Internal Memory Clock Enable */
+#define CKEN_KEYPAD (19) /* Keypad Interface Clock Enable */
+#define CKEN_USIM (18) /* USIM Unit Clock Enable */
+#define CKEN_MSL (17) /* MSL Unit Clock Enable */
+#define CKEN_LCD (16) /* LCD Unit Clock Enable */
+#define CKEN_PWRI2C (15) /* PWR I2C Unit Clock Enable */
+#define CKEN_I2C (14) /* I2C Unit Clock Enable */
+#define CKEN_FICP (13) /* FICP Unit Clock Enable */
+#define CKEN_MMC (12) /* MMC Unit Clock Enable */
+#define CKEN_USB (11) /* USB Unit Clock Enable */
+#define CKEN_ASSP (10) /* ASSP (SSP3) Clock Enable */
+#define CKEN_USBHOST (10) /* USB Host Unit Clock Enable */
+#define CKEN_OSTIMER (9) /* OS Timer Unit Clock Enable */
+#define CKEN_NSSP (9) /* NSSP (SSP2) Clock Enable */
+#define CKEN_I2S (8) /* I2S Unit Clock Enable */
+#define CKEN_BTUART (7) /* BTUART Unit Clock Enable */
+#define CKEN_FFUART (6) /* FFUART Unit Clock Enable */
+#define CKEN_STUART (5) /* STUART Unit Clock Enable */
+#define CKEN_HWUART (4) /* HWUART Unit Clock Enable */
+#define CKEN_SSP3 (4) /* SSP3 Unit Clock Enable */
+#define CKEN_SSP (3) /* SSP Unit Clock Enable */
+#define CKEN_SSP2 (3) /* SSP2 Unit Clock Enable */
+#define CKEN_AC97 (2) /* AC97 Unit Clock Enable */
+#define CKEN_PWM1 (1) /* PWM1 Clock Enable */
+#define CKEN_PWM0 (0) /* PWM0 Clock Enable */
#define OSCC_OON (1 << 1) /* 32.768kHz OON (write-once only bit) */
#define OSCC_OOK (1 << 0) /* 32.768kHz OOK (read-only bit) */
-
-/*
- * LCD
- */
-
-#define LCCR0 __REG(0x44000000) /* LCD Controller Control Register 0 */
-#define LCCR1 __REG(0x44000004) /* LCD Controller Control Register 1 */
-#define LCCR2 __REG(0x44000008) /* LCD Controller Control Register 2 */
-#define LCCR3 __REG(0x4400000C) /* LCD Controller Control Register 3 */
-#define DFBR0 __REG(0x44000020) /* DMA Channel 0 Frame Branch Register */
-#define DFBR1 __REG(0x44000024) /* DMA Channel 1 Frame Branch Register */
-#define LCSR __REG(0x44000038) /* LCD Controller Status Register */
-#define LIIDR __REG(0x4400003C) /* LCD Controller Interrupt ID Register */
-#define TMEDRGBR __REG(0x44000040) /* TMED RGB Seed Register */
-#define TMEDCR __REG(0x44000044) /* TMED Control Register */
-
-#define LCCR3_1BPP (0 << 24)
-#define LCCR3_2BPP (1 << 24)
-#define LCCR3_4BPP (2 << 24)
-#define LCCR3_8BPP (3 << 24)
-#define LCCR3_16BPP (4 << 24)
-
-#define FDADR0 __REG(0x44000200) /* DMA Channel 0 Frame Descriptor Address Register */
-#define FSADR0 __REG(0x44000204) /* DMA Channel 0 Frame Source Address Register */
-#define FIDR0 __REG(0x44000208) /* DMA Channel 0 Frame ID Register */
-#define LDCMD0 __REG(0x4400020C) /* DMA Channel 0 Command Register */
-#define FDADR1 __REG(0x44000210) /* DMA Channel 1 Frame Descriptor Address Register */
-#define FSADR1 __REG(0x44000214) /* DMA Channel 1 Frame Source Address Register */
-#define FIDR1 __REG(0x44000218) /* DMA Channel 1 Frame ID Register */
-#define LDCMD1 __REG(0x4400021C) /* DMA Channel 1 Command Register */
-
-#define LCCR0_ENB (1 << 0) /* LCD Controller enable */
-#define LCCR0_CMS (1 << 1) /* Color/Monochrome Display Select */
-#define LCCR0_Color (LCCR0_CMS*0) /* Color display */
-#define LCCR0_Mono (LCCR0_CMS*1) /* Monochrome display */
-#define LCCR0_SDS (1 << 2) /* Single/Dual Panel Display */
- /* Select */
-#define LCCR0_Sngl (LCCR0_SDS*0) /* Single panel display */
-#define LCCR0_Dual (LCCR0_SDS*1) /* Dual panel display */
-
-#define LCCR0_LDM (1 << 3) /* LCD Disable Done Mask */
-#define LCCR0_SFM (1 << 4) /* Start of frame mask */
-#define LCCR0_IUM (1 << 5) /* Input FIFO underrun mask */
-#define LCCR0_EFM (1 << 6) /* End of Frame mask */
-#define LCCR0_PAS (1 << 7) /* Passive/Active display Select */
-#define LCCR0_Pas (LCCR0_PAS*0) /* Passive display (STN) */
-#define LCCR0_Act (LCCR0_PAS*1) /* Active display (TFT) */
-#define LCCR0_DPD (1 << 9) /* Double Pixel Data (monochrome */
- /* display mode) */
-#define LCCR0_4PixMono (LCCR0_DPD*0) /* 4-Pixel/clock Monochrome */
- /* display */
-#define LCCR0_8PixMono (LCCR0_DPD*1) /* 8-Pixel/clock Monochrome */
- /* display */
-#define LCCR0_DIS (1 << 10) /* LCD Disable */
-#define LCCR0_QDM (1 << 11) /* LCD Quick Disable mask */
-#define LCCR0_PDD (0xff << 12) /* Palette DMA request delay */
-#define LCCR0_PDD_S 12
-#define LCCR0_BM (1 << 20) /* Branch mask */
-#define LCCR0_OUM (1 << 21) /* Output FIFO underrun mask */
-
-#define LCCR1_PPL Fld (10, 0) /* Pixels Per Line - 1 */
-#define LCCR1_DisWdth(Pixel) /* Display Width [1..800 pix.] */ \
- (((Pixel) - 1) << FShft (LCCR1_PPL))
-
-#define LCCR1_HSW Fld (6, 10) /* Horizontal Synchronization */
-#define LCCR1_HorSnchWdth(Tpix) /* Horizontal Synchronization */ \
- /* pulse Width [1..64 Tpix] */ \
- (((Tpix) - 1) << FShft (LCCR1_HSW))
-
-#define LCCR1_ELW Fld (8, 16) /* End-of-Line pixel clock Wait */
- /* count - 1 [Tpix] */
-#define LCCR1_EndLnDel(Tpix) /* End-of-Line Delay */ \
- /* [1..256 Tpix] */ \
- (((Tpix) - 1) << FShft (LCCR1_ELW))
-
-#define LCCR1_BLW Fld (8, 24) /* Beginning-of-Line pixel clock */
- /* Wait count - 1 [Tpix] */
-#define LCCR1_BegLnDel(Tpix) /* Beginning-of-Line Delay */ \
- /* [1..256 Tpix] */ \
- (((Tpix) - 1) << FShft (LCCR1_BLW))
-
-
-#define LCCR2_LPP Fld (10, 0) /* Line Per Panel - 1 */
-#define LCCR2_DisHght(Line) /* Display Height [1..1024 lines] */ \
- (((Line) - 1) << FShft (LCCR2_LPP))
-
-#define LCCR2_VSW Fld (6, 10) /* Vertical Synchronization pulse */
- /* Width - 1 [Tln] (L_FCLK) */
-#define LCCR2_VrtSnchWdth(Tln) /* Vertical Synchronization pulse */ \
- /* Width [1..64 Tln] */ \
- (((Tln) - 1) << FShft (LCCR2_VSW))
-
-#define LCCR2_EFW Fld (8, 16) /* End-of-Frame line clock Wait */
- /* count [Tln] */
-#define LCCR2_EndFrmDel(Tln) /* End-of-Frame Delay */ \
- /* [0..255 Tln] */ \
- ((Tln) << FShft (LCCR2_EFW))
-
-#define LCCR2_BFW Fld (8, 24) /* Beginning-of-Frame line clock */
- /* Wait count [Tln] */
-#define LCCR2_BegFrmDel(Tln) /* Beginning-of-Frame Delay */ \
- /* [0..255 Tln] */ \
- ((Tln) << FShft (LCCR2_BFW))
-
-#if 0
-#define LCCR3_PCD (0xff) /* Pixel clock divisor */
-#define LCCR3_ACB (0xff << 8) /* AC Bias pin frequency */
-#define LCCR3_ACB_S 8
-#endif
-
-#define LCCR3_API (0xf << 16) /* AC Bias pin trasitions per interrupt */
-#define LCCR3_API_S 16
-#define LCCR3_VSP (1 << 20) /* vertical sync polarity */
-#define LCCR3_HSP (1 << 21) /* horizontal sync polarity */
-#define LCCR3_PCP (1 << 22) /* Pixel Clock Polarity (L_PCLK) */
-#define LCCR3_PixRsEdg (LCCR3_PCP*0) /* Pixel clock Rising-Edge */
-#define LCCR3_PixFlEdg (LCCR3_PCP*1) /* Pixel clock Falling-Edge */
-
-#define LCCR3_OEP (1 << 23) /* Output Enable Polarity (L_BIAS, */
- /* active display mode) */
-#define LCCR3_OutEnH (LCCR3_OEP*0) /* Output Enable active High */
-#define LCCR3_OutEnL (LCCR3_OEP*1) /* Output Enable active Low */
-
-#if 0
-#define LCCR3_BPP (7 << 24) /* bits per pixel */
-#define LCCR3_BPP_S 24
-#endif
-#define LCCR3_DPC (1 << 27) /* double pixel clock mode */
-
-
-#define LCCR3_PCD Fld (8, 0) /* Pixel Clock Divisor */
-#define LCCR3_PixClkDiv(Div) /* Pixel Clock Divisor */ \
- (((Div) << FShft (LCCR3_PCD)))
-
-
-#define LCCR3_BPP Fld (3, 24) /* Bit Per Pixel */
-#define LCCR3_Bpp(Bpp) /* Bit Per Pixel */ \
- (((Bpp) << FShft (LCCR3_BPP)))
-
-#define LCCR3_ACB Fld (8, 8) /* AC Bias */
-#define LCCR3_Acb(Acb) /* BAC Bias */ \
- (((Acb) << FShft (LCCR3_ACB)))
-
-#define LCCR3_HorSnchH (LCCR3_HSP*0) /* Horizontal Synchronization */
- /* pulse active High */
-#define LCCR3_HorSnchL (LCCR3_HSP*1) /* Horizontal Synchronization */
-
-#define LCCR3_VrtSnchH (LCCR3_VSP*0) /* Vertical Synchronization pulse */
- /* active High */
-#define LCCR3_VrtSnchL (LCCR3_VSP*1) /* Vertical Synchronization pulse */
- /* active Low */
-
-#define LCSR_LDD (1 << 0) /* LCD Disable Done */
-#define LCSR_SOF (1 << 1) /* Start of frame */
-#define LCSR_BER (1 << 2) /* Bus error */
-#define LCSR_ABC (1 << 3) /* AC Bias count */
-#define LCSR_IUL (1 << 4) /* input FIFO underrun Lower panel */
-#define LCSR_IUU (1 << 5) /* input FIFO underrun Upper panel */
-#define LCSR_OU (1 << 6) /* output FIFO underrun */
-#define LCSR_QD (1 << 7) /* quick disable */
-#define LCSR_EOF (1 << 8) /* end of frame */
-#define LCSR_BS (1 << 9) /* branch status */
-#define LCSR_SINT (1 << 10) /* subsequent interrupt */
-
-#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */
-
-#define LCSR_LDD (1 << 0) /* LCD Disable Done */
-#define LCSR_SOF (1 << 1) /* Start of frame */
-#define LCSR_BER (1 << 2) /* Bus error */
-#define LCSR_ABC (1 << 3) /* AC Bias count */
-#define LCSR_IUL (1 << 4) /* input FIFO underrun Lower panel */
-#define LCSR_IUU (1 << 5) /* input FIFO underrun Upper panel */
-#define LCSR_OU (1 << 6) /* output FIFO underrun */
-#define LCSR_QD (1 << 7) /* quick disable */
-#define LCSR_EOF (1 << 8) /* end of frame */
-#define LCSR_BS (1 << 9) /* branch status */
-#define LCSR_SINT (1 << 10) /* subsequent interrupt */
-
-#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */
-
-/*
- * Memory controller
- */
-
-#define MDCNFG __REG(0x48000000) /* SDRAM Configuration Register 0 */
-#define MDREFR __REG(0x48000004) /* SDRAM Refresh Control Register */
-#define MSC0 __REG(0x48000008) /* Static Memory Control Register 0 */
-#define MSC1 __REG(0x4800000C) /* Static Memory Control Register 1 */
-#define MSC2 __REG(0x48000010) /* Static Memory Control Register 2 */
-#define MECR __REG(0x48000014) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
-#define SXLCR __REG(0x48000018) /* LCR value to be written to SDRAM-Timing Synchronous Flash */
-#define SXCNFG __REG(0x4800001C) /* Synchronous Static Memory Control Register */
-#define SXMRS __REG(0x48000024) /* MRS value to be written to Synchronous Flash or SMROM */
-#define MCMEM0 __REG(0x48000028) /* Card interface Common Memory Space Socket 0 Timing */
-#define MCMEM1 __REG(0x4800002C) /* Card interface Common Memory Space Socket 1 Timing */
-#define MCATT0 __REG(0x48000030) /* Card interface Attribute Space Socket 0 Timing Configuration */
-#define MCATT1 __REG(0x48000034) /* Card interface Attribute Space Socket 1 Timing Configuration */
-#define MCIO0 __REG(0x48000038) /* Card interface I/O Space Socket 0 Timing Configuration */
-#define MCIO1 __REG(0x4800003C) /* Card interface I/O Space Socket 1 Timing Configuration */
-#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */
-#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
-
-/*
- * More handy macros for PCMCIA
- *
- * Arg is socket number
- */
-#define MCMEM(s) __REG2(0x48000028, (s)<<2 ) /* Card interface Common Memory Space Socket s Timing */
-#define MCATT(s) __REG2(0x48000030, (s)<<2 ) /* Card interface Attribute Space Socket s Timing Configuration */
-#define MCIO(s) __REG2(0x48000038, (s)<<2 ) /* Card interface I/O Space Socket s Timing Configuration */
-
-/* MECR register defines */
-#define MECR_NOS (1 << 0) /* Number Of Sockets: 0 -> 1 sock, 1 -> 2 sock */
-#define MECR_CIT (1 << 1) /* Card Is There: 0 -> no card, 1 -> card inserted */
-
-#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */
-#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */
-#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */
-#define MDREFR_SLFRSH (1 << 22) /* SDRAM Self-Refresh Control/Status */
-#define MDREFR_APD (1 << 20) /* SDRAM/SSRAM Auto-Power-Down Enable */
-#define MDREFR_K2DB2 (1 << 19) /* SDCLK2 Divide by 2 Control/Status */
-#define MDREFR_K2RUN (1 << 18) /* SDCLK2 Run Control/Status */
-#define MDREFR_K1DB2 (1 << 17) /* SDCLK1 Divide by 2 Control/Status */
-#define MDREFR_K1RUN (1 << 16) /* SDCLK1 Run Control/Status */
-#define MDREFR_E1PIN (1 << 15) /* SDCKE1 Level Control/Status */
-#define MDREFR_K0DB2 (1 << 14) /* SDCLK0 Divide by 2 Control/Status */
-#define MDREFR_K0RUN (1 << 13) /* SDCLK0 Run Control/Status */
-#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */
-
-
#ifdef CONFIG_PXA27x
-/*
- * Keypad
- */
-#define KPC __REG(0x41500000) /* Keypad Interface Control register */
-#define KPDK __REG(0x41500008) /* Keypad Interface Direct Key register */
-#define KPREC __REG(0x41500010) /* Keypad Interface Rotary Encoder register */
-#define KPMK __REG(0x41500018) /* Keypad Interface Matrix Key register */
-#define KPAS __REG(0x41500020) /* Keypad Interface Automatic Scan register */
-#define KPASMKP0 __REG(0x41500028) /* Keypad Interface Automatic Scan Multiple Key Presser register 0 */
-#define KPASMKP1 __REG(0x41500030) /* Keypad Interface Automatic Scan Multiple Key Presser register 1 */
-#define KPASMKP2 __REG(0x41500038) /* Keypad Interface Automatic Scan Multiple Key Presser register 2 */
-#define KPASMKP3 __REG(0x41500040) /* Keypad Interface Automatic Scan Multiple Key Presser register 3 */
-#define KPKDI __REG(0x41500048) /* Keypad Interface Key Debounce Interval register */
-
-#define KPC_AS (0x1 << 30) /* Automatic Scan bit */
-#define KPC_ASACT (0x1 << 29) /* Automatic Scan on Activity */
-#define KPC_MI (0x1 << 22) /* Matrix interrupt bit */
-#define KPC_IMKP (0x1 << 21) /* Ignore Multiple Key Press */
-#define KPC_MS7 (0x1 << 20) /* Matrix scan line 7 */
-#define KPC_MS6 (0x1 << 19) /* Matrix scan line 6 */
-#define KPC_MS5 (0x1 << 18) /* Matrix scan line 5 */
-#define KPC_MS4 (0x1 << 17) /* Matrix scan line 4 */
-#define KPC_MS3 (0x1 << 16) /* Matrix scan line 3 */
-#define KPC_MS2 (0x1 << 15) /* Matrix scan line 2 */
-#define KPC_MS1 (0x1 << 14) /* Matrix scan line 1 */
-#define KPC_MS0 (0x1 << 13) /* Matrix scan line 0 */
-#define KPC_MS_ALL (KPC_MS0 | KPC_MS1 | KPC_MS2 | KPC_MS3 | KPC_MS4 | KPC_MS5 | KPC_MS6 | KPC_MS7)
-#define KPC_ME (0x1 << 12) /* Matrix Keypad Enable */
-#define KPC_MIE (0x1 << 11) /* Matrix Interrupt Enable */
-#define KPC_DK_DEB_SEL (0x1 << 9) /* Direct Keypad Debounce Select */
-#define KPC_DI (0x1 << 5) /* Direct key interrupt bit */
-#define KPC_RE_ZERO_DEB (0x1 << 4) /* Rotary Encoder Zero Debounce */
-#define KPC_REE1 (0x1 << 3) /* Rotary Encoder1 Enable */
-#define KPC_REE0 (0x1 << 2) /* Rotary Encoder0 Enable */
-#define KPC_DE (0x1 << 1) /* Direct Keypad Enable */
-#define KPC_DIE (0x1 << 0) /* Direct Keypad interrupt Enable */
-
-#define KPDK_DKP (0x1 << 31)
-#define KPDK_DK7 (0x1 << 7)
-#define KPDK_DK6 (0x1 << 6)
-#define KPDK_DK5 (0x1 << 5)
-#define KPDK_DK4 (0x1 << 4)
-#define KPDK_DK3 (0x1 << 3)
-#define KPDK_DK2 (0x1 << 2)
-#define KPDK_DK1 (0x1 << 1)
-#define KPDK_DK0 (0x1 << 0)
-
-#define KPREC_OF1 (0x1 << 31)
-#define kPREC_UF1 (0x1 << 30)
-#define KPREC_OF0 (0x1 << 15)
-#define KPREC_UF0 (0x1 << 14)
-
-#define KPMK_MKP (0x1 << 31)
-#define KPAS_SO (0x1 << 31)
-#define KPASMKPx_SO (0x1 << 31)
-
-/*
- * UHC: USB Host Controller (OHCI-like) register definitions
- */
-#define UHC_BASE_PHYS (0x4C000000)
-#define UHCREV __REG(0x4C000000) /* UHC HCI Spec Revision */
-#define UHCHCON __REG(0x4C000004) /* UHC Host Control Register */
-#define UHCCOMS __REG(0x4C000008) /* UHC Command Status Register */
-#define UHCINTS __REG(0x4C00000C) /* UHC Interrupt Status Register */
-#define UHCINTE __REG(0x4C000010) /* UHC Interrupt Enable */
-#define UHCINTD __REG(0x4C000014) /* UHC Interrupt Disable */
-#define UHCHCCA __REG(0x4C000018) /* UHC Host Controller Comm. Area */
-#define UHCPCED __REG(0x4C00001C) /* UHC Period Current Endpt Descr */
-#define UHCCHED __REG(0x4C000020) /* UHC Control Head Endpt Descr */
-#define UHCCCED __REG(0x4C000024) /* UHC Control Current Endpt Descr */
-#define UHCBHED __REG(0x4C000028) /* UHC Bulk Head Endpt Descr */
-#define UHCBCED __REG(0x4C00002C) /* UHC Bulk Current Endpt Descr */
-#define UHCDHEAD __REG(0x4C000030) /* UHC Done Head */
-#define UHCFMI __REG(0x4C000034) /* UHC Frame Interval */
-#define UHCFMR __REG(0x4C000038) /* UHC Frame Remaining */
-#define UHCFMN __REG(0x4C00003C) /* UHC Frame Number */
-#define UHCPERS __REG(0x4C000040) /* UHC Periodic Start */
-#define UHCLS __REG(0x4C000044) /* UHC Low Speed Threshold */
-#define UHCRHDA __REG(0x4C000048) /* UHC Root Hub Descriptor A */
-#define UHCRHDB __REG(0x4C00004C) /* UHC Root Hub Descriptor B */
-#define UHCRHS __REG(0x4C000050) /* UHC Root Hub Status */
-#define UHCRHPS1 __REG(0x4C000054) /* UHC Root Hub Port 1 Status */
-#define UHCRHPS2 __REG(0x4C000058) /* UHC Root Hub Port 2 Status */
-#define UHCRHPS3 __REG(0x4C00005C) /* UHC Root Hub Port 3 Status */
-
-#define UHCSTAT __REG(0x4C000060) /* UHC Status Register */
-#define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */
-#define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/
-#define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/
-#define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */
-#define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */
-#define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */
-#define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */
-#define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */
-#define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */
-
-#define UHCHR __REG(0x4C000064) /* UHC Reset Register */
-#define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */
-#define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */
-#define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */
-#define UHCHR_PCPL (1 << 7) /* Power control polarity low */
-#define UHCHR_PSPL (1 << 6) /* Power sense polarity low */
-#define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */
-#define UHCHR_UIT (1 << 4) /* USB Interrupt Test */
-#define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */
-#define UHCHR_CGR (1 << 2) /* Clock Generation Reset */
-#define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */
-#define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */
-
-#define UHCHIE __REG(0x4C000068) /* UHC Interrupt Enable Register*/
-#define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */
-#define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */
-#define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */
-#define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */
-#define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort
- Interrupt Enable*/
-#define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */
-#define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */
-
-#define UHCHIT __REG(0x4C00006C) /* UHC Interrupt Test register */
-
/* Camera Interface */
#define CICR0 __REG(0x50000000)
#define CICR1 __REG(0x50000004)
#define CICR0_FOM (1 << 0) /* FIFO-overrun mask */
#define CICR1_TBIT (1 << 31) /* Transparency bit */
-#define CICR1_RGBT_CONV (0x3 << 30) /* RGBT conversion mask */
-#define CICR1_PPL (0x3f << 15) /* Pixels per line mask */
+#define CICR1_RGBT_CONV (0x3 << 29) /* RGBT conversion mask */
+#define CICR1_PPL (0x7ff << 15) /* Pixels per line mask */
#define CICR1_RGB_CONV (0x7 << 12) /* RGB conversion mask */
#define CICR1_RGB_F (1 << 11) /* RGB format */
#define CICR1_YCBCR_F (1 << 10) /* YCbCr format */
#define CICR3_VSW (0x3f << 10) /* Vertical sync pulse width mask */
#define CICR3_BFPW (0x3f << 3) /* Beginning-of-frame pixel clock
wait count mask */
-#define CICR3_LPF (0x3ff << 0) /* Lines per frame mask */
+#define CICR3_LPF (0x7ff << 0) /* Lines per frame mask */
#define CICR4_MCLK_DLY (0x3 << 24) /* MCLK Data Capture Delay mask */
#define CICR4_PCLK_EN (1 << 23) /* Pixel clock enable */
#define CISR_EOL (1 << 8) /* End of line */
#define CISR_PAR_ERR (1 << 7) /* Parity error */
#define CISR_CQD (1 << 6) /* Camera interface quick disable */
-#define CISR_SOF (1 << 5) /* Start of frame */
-#define CISR_CDD (1 << 4) /* Camera interface disable done */
+#define CISR_CDD (1 << 5) /* Camera interface disable done */
+#define CISR_SOF (1 << 4) /* Start of frame */
#define CISR_EOF (1 << 3) /* End of frame */
#define CISR_IFO_2 (1 << 2) /* FIFO overrun for Channel 2 */
#define CISR_IFO_1 (1 << 1) /* FIFO overrun for Channel 1 */
#endif
+#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
+/*
+ * UHC: USB Host Controller (OHCI-like) register definitions
+ */
+#define UHC_BASE_PHYS (0x4C000000)
+#define UHCREV __REG(0x4C000000) /* UHC HCI Spec Revision */
+#define UHCHCON __REG(0x4C000004) /* UHC Host Control Register */
+#define UHCCOMS __REG(0x4C000008) /* UHC Command Status Register */
+#define UHCINTS __REG(0x4C00000C) /* UHC Interrupt Status Register */
+#define UHCINTE __REG(0x4C000010) /* UHC Interrupt Enable */
+#define UHCINTD __REG(0x4C000014) /* UHC Interrupt Disable */
+#define UHCHCCA __REG(0x4C000018) /* UHC Host Controller Comm. Area */
+#define UHCPCED __REG(0x4C00001C) /* UHC Period Current Endpt Descr */
+#define UHCCHED __REG(0x4C000020) /* UHC Control Head Endpt Descr */
+#define UHCCCED __REG(0x4C000024) /* UHC Control Current Endpt Descr */
+#define UHCBHED __REG(0x4C000028) /* UHC Bulk Head Endpt Descr */
+#define UHCBCED __REG(0x4C00002C) /* UHC Bulk Current Endpt Descr */
+#define UHCDHEAD __REG(0x4C000030) /* UHC Done Head */
+#define UHCFMI __REG(0x4C000034) /* UHC Frame Interval */
+#define UHCFMR __REG(0x4C000038) /* UHC Frame Remaining */
+#define UHCFMN __REG(0x4C00003C) /* UHC Frame Number */
+#define UHCPERS __REG(0x4C000040) /* UHC Periodic Start */
+#define UHCLS __REG(0x4C000044) /* UHC Low Speed Threshold */
+
+#define UHCRHDA __REG(0x4C000048) /* UHC Root Hub Descriptor A */
+#define UHCRHDA_NOCP (1 << 12) /* No over current protection */
+
+#define UHCRHDB __REG(0x4C00004C) /* UHC Root Hub Descriptor B */
+#define UHCRHS __REG(0x4C000050) /* UHC Root Hub Status */
+#define UHCRHPS1 __REG(0x4C000054) /* UHC Root Hub Port 1 Status */
+#define UHCRHPS2 __REG(0x4C000058) /* UHC Root Hub Port 2 Status */
+#define UHCRHPS3 __REG(0x4C00005C) /* UHC Root Hub Port 3 Status */
+
+#define UHCSTAT __REG(0x4C000060) /* UHC Status Register */
+#define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */
+#define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/
+#define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/
+#define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */
+#define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */
+#define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */
+#define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */
+#define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */
+#define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */
+
+#define UHCHR __REG(0x4C000064) /* UHC Reset Register */
+#define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */
+#define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */
+#define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */
+#define UHCHR_PCPL (1 << 7) /* Power control polarity low */
+#define UHCHR_PSPL (1 << 6) /* Power sense polarity low */
+#define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */
+#define UHCHR_UIT (1 << 4) /* USB Interrupt Test */
+#define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */
+#define UHCHR_CGR (1 << 2) /* Clock Generation Reset */
+#define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */
+#define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */
+
+#define UHCHIE __REG(0x4C000068) /* UHC Interrupt Enable Register*/
+#define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */
+#define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */
+#define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */
+#define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */
+#define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort
+ Interrupt Enable*/
+#define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */
+#define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */
+
+#define UHCHIT __REG(0x4C00006C) /* UHC Interrupt Test register */
+
+#endif /* CONFIG_PXA27x || CONFIG_PXA3xx */
+
+/* PWRMODE register M field values */
+
+#define PWRMODE_IDLE 0x1
+#define PWRMODE_STANDBY 0x2
+#define PWRMODE_SLEEP 0x3
+#define PWRMODE_DEEPSLEEP 0x7
+
#endif
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff