To compile this driver as a module, choose M here: the
module will be called softdog.
+config WM831X_WATCHDOG
+ tristate "WM831x watchdog"
+ depends on MFD_WM831X
+ help
+ Support for the watchdog in the WM831x AudioPlus PMICs. When
+ the watchdog triggers the system will be reset.
+
config WM8350_WATCHDOG
tristate "WM8350 watchdog"
depends on MFD_WM8350
config OMAP_WATCHDOG
tristate "OMAP Watchdog"
- depends on ARCH_OMAP16XX || ARCH_OMAP24XX || ARCH_OMAP34XX
+ depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
help
- Support for TI OMAP1610/OMAP1710/OMAP2420/OMAP3430 watchdog. Say 'Y'
- here to enable the OMAP1610/OMAP1710/OMAP2420/OMAP3430 watchdog timer.
+ Support for TI OMAP1610/OMAP1710/OMAP2420/OMAP3430/OMAP4430 watchdog. Say 'Y'
+ here to enable the OMAP1610/OMAP1710/OMAP2420/OMAP3430/OMAP4430 watchdog timer.
config PNX4008_WATCHDOG
tristate "PNX4008 Watchdog"
NOTE: once enabled, this timer cannot be disabled.
Say N if you are unsure.
-config ORION5X_WATCHDOG
- tristate "Orion5x watchdog"
- depends on ARCH_ORION5X
+config ORION_WATCHDOG
+ tristate "Orion watchdog"
+ depends on ARCH_ORION5X || ARCH_KIRKWOOD
+ help
+ Say Y here if to include support for the watchdog timer
+ in the Marvell Orion5x and Kirkwood ARM SoCs.
+ To compile this driver as a module, choose M here: the
+ module will be called orion_wdt.
+
+config COH901327_WATCHDOG
+ bool "ST-Ericsson COH 901 327 watchdog"
+ depends on ARCH_U300
+ default y if MACH_U300
+ help
+ Say Y here to include Watchdog timer support for the
+ watchdog embedded into the ST-Ericsson U300 series platforms.
+ This watchdog is used to reset the system and thus cannot be
+ compiled as a module.
+
+config TWL4030_WATCHDOG
+ tristate "TWL4030 Watchdog"
+ depends on TWL4030_CORE
+ help
+ Support for TI TWL4030 watchdog. Say 'Y' here to enable the
+ watchdog timer support for TWL4030 chips.
+
+config STMP3XXX_WATCHDOG
+ tristate "Freescale STMP3XXX watchdog"
+ depends on ARCH_STMP3XXX
+ help
+ Say Y here if to include support for the watchdog timer
+ for the Sigmatel STMP37XX/378X SoC.
+ To compile this driver as a module, choose M here: the
+ module will be called stmp3xxx_wdt.
+
+config NUC900_WATCHDOG
+ tristate "Nuvoton NUC900 watchdog"
+ depends on ARCH_W90X900
help
Say Y here if to include support for the watchdog timer
- in the Orion5x ARM SoCs.
+ for the Nuvoton NUC900 series SoCs.
+ To compile this driver as a module, choose M here: the
+ module will be called nuc900_wdt.
+
+config ADX_WATCHDOG
+ tristate "Avionic Design Xanthos watchdog"
+ depends on ARCH_PXA_ADX
+ help
+ Say Y here if you want support for the watchdog timer on Avionic
+ Design Xanthos boards.
+
+config TS72XX_WATCHDOG
+ tristate "TS-72XX SBC Watchdog"
+ depends on MACH_TS72XX
+ help
+ Technologic Systems TS-7200, TS-7250 and TS-7260 boards have
+ watchdog timer implemented in a external CPLD chip. Say Y here
+ if you want to support for the watchdog timer on TS-72XX boards.
+
To compile this driver as a module, choose M here: the
- module will be called orion5x_wdt.
+ module will be called ts72xx_wdt.
-# ARM26 Architecture
+config MAX63XX_WATCHDOG
+ tristate "Max63xx watchdog"
+ depends on ARM && HAS_IOMEM
+ help
+ Support for memory mapped max63{69,70,71,72,73,74} watchdog timer.
# AVR32 Architecture
config GEODE_WDT
tristate "AMD Geode CS5535/CS5536 Watchdog"
- depends on MGEODE_LX
+ depends on CS5535_MFGPT
help
This driver enables a watchdog capability built into the
CS5535/CS5536 companion chips for the AMD Geode GX and LX
You can compile this driver directly into the kernel, or use
it as a module. The module will be called sc520_wdt.
+config SBC_FITPC2_WATCHDOG
+ tristate "Compulab SBC-FITPC2 watchdog"
+ depends on X86
+ ---help---
+ This is the driver for the built-in watchdog timer on the fit-PC2,
+ fit-PC2i, CM-iAM single-board computers made by Compulab.
+
+ It`s possible to enable watchdog timer either from BIOS (F2) or from booted Linux.
+ When "Watchdog Timer Value" enabled one can set 31-255 s operational range.
+
+ Entering BIOS setup temporary disables watchdog operation regardless to current state,
+ so system will not be restarted while user in BIOS setup.
+
+ Once watchdog was enabled the system will be restarted every
+ "Watchdog Timer Value" period, so to prevent it user can restart or
+ disable the watchdog.
+
+ To compile this driver as a module, choose M here: the
+ module will be called sbc_fitpc2_wdt.
+
+ Most people will say N.
+
config EUROTECH_WDT
tristate "Eurotech CPU-1220/1410 Watchdog Timer"
depends on X86
Board Computer produced by Axiomtek Co., Ltd. (www.axiomtek.com).
To compile this driver as a module, choose M here: the
- module will be called sbc8360.ko.
+ module will be called sbc8360.
Most people will say N.
# MIPS Architecture
+config BCM47XX_WDT
+ tristate "Broadcom BCM47xx Watchdog Timer"
+ depends on BCM47XX
+ help
+ Hardware driver for the Broadcom BCM47xx Watchog Timer.
+
config RC32434_WDT
tristate "IDT RC32434 SoC Watchdog Timer"
depends on MIKROTIK_RB532
Hardware driver for the MTX-1 boards. This is a watchdog timer that
will reboot the machine after a 100 seconds timer expired.
-config WDT_RM9K_GPI
- tristate "RM9000/GPI hardware watchdog"
- depends on CPU_RM9000
+config PNX833X_WDT
+ tristate "PNX833x Hardware Watchdog"
+ depends on SOC_PNX8335
help
- Watchdog implementation using the GPI hardware found on
- PMC-Sierra RM9xxx CPUs.
-
- To compile this driver as a module, choose M here: the
- module will be called rm9k_wdt.
+ Hardware driver for the PNX833x's watchdog. This is a
+ watchdog timer that will reboot the machine after a programable
+ timer has expired and no process has written to /dev/watchdog during
+ that time.
config SIBYTE_WDOG
tristate "Sibyte SoC hardware watchdog"
# POWERPC Architecture
config GEF_WDT
- tristate "GE Fanuc Watchdog Timer"
- depends on GEF_SBC610
+ tristate "GE Watchdog Timer"
+ depends on GEF_SBC610 || GEF_SBC310 || GEF_PPC9A
---help---
- Watchdog timer found in a number of GE Fanuc single board computers.
+ Watchdog timer found in a number of GE single board computers.
config MPC5200_WDT
- tristate "MPC5200 Watchdog Timer"
+ bool "MPC52xx Watchdog Timer"
depends on PPC_MPC52xx
+ help
+ Use General Purpose Timer (GPT) 0 on the MPC5200 as Watchdog.
config 8xxx_WDT
tristate "MPC8xxx Platform Watchdog Timer"
To compile this driver as a module, choose M here: the
module will be called wdt.
-config WDT_501
- bool "WDT501 features"
- depends on WDT
- help
- Saying Y here and creating a character special file /dev/temperature
- with major number 10 and minor number 131 ("man mknod") will give
- you a thermometer inside your computer: reading from
- /dev/temperature yields one byte, the temperature in degrees
- Fahrenheit. This works only if you have a WDT501P watchdog board
- installed.
-
- If you want to enable the Fan Tachometer on the WDT501P, then you
- can do this via the tachometer parameter. Only do this if you have a
- fan tachometer actually set up.
-
#
# PCI-based Watchdog Cards
#
---help---
If you have a PCI-WDT500/501 watchdog board, say Y here, otherwise N.
- To compile this driver as a module, choose M here: the
- module will be called wdt_pci.
-
-config WDT_501_PCI
- bool "PCI-WDT501 features"
- depends on WDTPCI
- help
- Saying Y here and creating a character special file /dev/temperature
- with major number 10 and minor number 131 ("man mknod") will give
- you a thermometer inside your computer: reading from
- /dev/temperature yields one byte, the temperature in degrees
- Fahrenheit. This works only if you have a PCI-WDT501 watchdog board
- installed.
+ If you have a PCI-WDT501 watchdog board then you can enable the
+ temperature sensor by setting the type parameter to 501.
If you want to enable the Fan Tachometer on the PCI-WDT501, then you
can do this via the tachometer parameter. Only do this if you have a
fan tachometer actually set up.
+ To compile this driver as a module, choose M here: the
+ module will be called wdt_pci.
+
#
# USB-based Watchdog Cards
#