Enable this to be able to choose the drivers for controlling the
backlight and the LCD panel on some platforms, for example on PDAs.
-config BACKLIGHT_CLASS_DEVICE
- tristate "Lowlevel Backlight controls"
+#
+# LCD
+#
+config LCD_CLASS_DEVICE
+ tristate "Lowlevel LCD controls"
depends on BACKLIGHT_LCD_SUPPORT
default m
help
- This framework adds support for low-level control of the LCD
- backlight. This includes support for brightness and power.
+ This framework adds support for low-level control of LCD.
+ Some framebuffer devices connect to platform-specific LCD modules
+ in order to have a platform-specific way to control the flat panel
+ (contrast and applying power to the LCD (not to the backlight!)).
To have support for your specific LCD panel you will have to
select the proper drivers which depend on this option.
-config BACKLIGHT_DEVICE
- bool
- depends on BACKLIGHT_CLASS_DEVICE
+config LCD_CORGI
+ tristate "LCD Panel support for SHARP corgi/spitz model"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER && PXA_SHARPSL
+ help
+ Say y here to support the LCD panels usually found on SHARP
+ corgi (C7x0) and spitz (Cxx00) models.
+
+config LCD_L4F00242T03
+ tristate "Epson L4F00242T03 LCD"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER && GENERIC_GPIO
+ help
+ SPI driver for Epson L4F00242T03. This provides basic support
+ for init and powering the LCD up/down through a sysfs interface.
+
+config LCD_LMS283GF05
+ tristate "Samsung LMS283GF05 LCD"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER && GENERIC_GPIO
+ help
+ SPI driver for Samsung LMS283GF05. This provides basic support
+ for powering the LCD up/down through a sysfs interface.
+
+config LCD_LTV350QV
+ tristate "Samsung LTV350QV LCD Panel"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER
+ default n
+ help
+ If you have a Samsung LTV350QV LCD panel, say y to include a
+ power control driver for it. The panel starts up in power
+ off state, so you need this driver in order to see any
+ output.
+
+ The LTV350QV panel is present on all ATSTK1000 boards.
+
+config LCD_ILI9320
+ tristate
+ depends on LCD_CLASS_DEVICE && BACKLIGHT_LCD_SUPPORT
+ default n
+ help
+ If you have a panel based on the ILI9320 controller chip
+ then say y to include a power driver for it.
+
+config LCD_TDO24M
+ tristate "Toppoly TDO24M and TDO35S LCD Panels support"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER
+ default n
+ help
+ If you have a Toppoly TDO24M/TDO35S series LCD panel, say y here to
+ include the support for it.
+
+config LCD_VGG2432A4
+ tristate "VGG2432A4 LCM device support"
+ depends on BACKLIGHT_LCD_SUPPORT && LCD_CLASS_DEVICE && SPI_MASTER
+ select LCD_ILI9320
+ default n
+ help
+ If you have a VGG2432A4 panel based on the ILI9320 controller chip
+ then say y to include a power driver for it.
+
+config LCD_PLATFORM
+ tristate "Platform LCD controls"
+ depends on LCD_CLASS_DEVICE
+ help
+ This driver provides a platform-device registered LCD power
+ control interface.
+
+config LCD_TOSA
+ tristate "Sharp SL-6000 LCD Driver"
+ depends on LCD_CLASS_DEVICE && SPI
+ depends on MACH_TOSA
+ default n
+ help
+ If you have an Sharp SL-6000 Zaurus say Y to enable a driver
+ for its LCD.
+
+config LCD_HP700
+ tristate "HP Jornada 700 series LCD Driver"
+ depends on LCD_CLASS_DEVICE
+ depends on SA1100_JORNADA720_SSP && !PREEMPT
default y
+ help
+ If you have an HP Jornada 700 series handheld (710/720/728)
+ say Y to enable LCD control driver.
-config LCD_CLASS_DEVICE
- tristate "Lowlevel LCD controls"
+#
+# Backlight
+#
+config BACKLIGHT_CLASS_DEVICE
+ tristate "Lowlevel Backlight controls"
depends on BACKLIGHT_LCD_SUPPORT
default m
help
- This framework adds support for low-level control of LCD.
- Some framebuffer devices connect to platform-specific LCD modules
- in order to have a platform-specific way to control the flat panel
- (contrast and applying power to the LCD (not to the backlight!)).
+ This framework adds support for low-level control of the LCD
+ backlight. This includes support for brightness and power.
To have support for your specific LCD panel you will have to
select the proper drivers which depend on this option.
-config LCD_DEVICE
- bool
- depends on LCD_CLASS_DEVICE
- default y
+config BACKLIGHT_ATMEL_LCDC
+ bool "Atmel LCDC Contrast-as-Backlight control"
+ depends on BACKLIGHT_CLASS_DEVICE && FB_ATMEL
+ default y if MACH_SAM9261EK || MACH_SAM9G10EK || MACH_SAM9263EK
+ help
+ This provides a backlight control internal to the Atmel LCDC
+ driver. If the LCD "contrast control" on your board is wired
+ so it controls the backlight brightness, select this option to
+ export this as a PWM-based backlight control.
-config BACKLIGHT_CORGI
- tristate "Sharp Corgi Backlight Driver (SL Series)"
- depends on BACKLIGHT_DEVICE && PXA_SHARPSL
+ If in doubt, it's safe to enable this option; it doesn't kick
+ in unless the board's description says it's wired that way.
+
+config BACKLIGHT_ATMEL_PWM
+ tristate "Atmel PWM backlight control"
+ depends on BACKLIGHT_CLASS_DEVICE && ATMEL_PWM
+ default n
+ help
+ Say Y here if you want to use the PWM peripheral in Atmel AT91 and
+ AVR32 devices. This driver will need additional platform data to know
+ which PWM instance to use and how to configure it.
+
+ To compile this driver as a module, choose M here: the module will be
+ called atmel-pwm-bl.
+
+config BACKLIGHT_GENERIC
+ tristate "Generic (aka Sharp Corgi) Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE
default y
help
- If you have a Sharp Zaurus SL-C7xx, SL-Cxx00 or SL-6000x say y to enable the
- backlight driver.
+ Say y to enable the generic platform backlight driver previously
+ known as the Corgi backlight driver. If you have a Sharp Zaurus
+ SL-C7xx, SL-Cxx00 or SL-6000x say y.
config BACKLIGHT_LOCOMO
tristate "Sharp LOCOMO LCD/Backlight Driver"
- depends on BACKLIGHT_DEVICE && SHARP_LOCOMO
+ depends on BACKLIGHT_CLASS_DEVICE && SHARP_LOCOMO
default y
help
If you have a Sharp Zaurus SL-5500 (Collie) or SL-5600 (Poodle) say y to
enable the LCD/backlight driver.
+config BACKLIGHT_OMAP1
+ tristate "OMAP1 PWL-based LCD Backlight"
+ depends on BACKLIGHT_CLASS_DEVICE && ARCH_OMAP1
+ default y
+ help
+ This driver controls the LCD backlight level and power for
+ the PWL module of OMAP1 processors. Say Y if your board
+ uses this hardware.
+
config BACKLIGHT_HP680
tristate "HP Jornada 680 Backlight Driver"
- depends on BACKLIGHT_DEVICE && SH_HP6XX
+ depends on BACKLIGHT_CLASS_DEVICE && SH_HP6XX
default y
help
If you have a HP Jornada 680, say y to enable the
backlight driver.
+config BACKLIGHT_HP700
+ tristate "HP Jornada 700 series Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE
+ depends on SA1100_JORNADA720_SSP && !PREEMPT
+ default y
+ help
+ If you have an HP Jornada 700 series,
+ say Y to include backlight control driver.
+
config BACKLIGHT_PROGEAR
tristate "Frontpath ProGear Backlight Driver"
- depends on BACKLIGHT_DEVICE && PCI && X86
+ depends on BACKLIGHT_CLASS_DEVICE && PCI && X86
default n
help
If you have a Frontpath ProGear say Y to enable the
backlight driver.
+config BACKLIGHT_CARILLO_RANCH
+ tristate "Intel Carillo Ranch Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && LCD_CLASS_DEVICE && PCI && X86 && FB_LE80578
+ default n
+ help
+ If you have a Intel LE80578 (Carillo Ranch) say Y to enable the
+ backlight driver.
+
+config BACKLIGHT_PWM
+ tristate "Generic PWM based Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && HAVE_PWM
+ help
+ If you have a LCD backlight adjustable by PWM, say Y to enable
+ this driver.
+
+config BACKLIGHT_DA903X
+ tristate "Backlight Driver for DA9030/DA9034 using WLED"
+ depends on BACKLIGHT_CLASS_DEVICE && PMIC_DA903X
+ help
+ If you have a LCD backlight connected to the WLED output of DA9030
+ or DA9034 WLED output, say Y here to enable this driver.
+
+config BACKLIGHT_MAX8925
+ tristate "Backlight driver for MAX8925"
+ depends on BACKLIGHT_CLASS_DEVICE && MFD_MAX8925
+ help
+ If you have a LCD backlight connected to the WLED output of MAX8925
+ WLED output, say Y here to enable this driver.
+
+config BACKLIGHT_MBP_NVIDIA
+ tristate "MacBook Pro Nvidia Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && X86
+ default n
+ help
+ If you have an Apple Macbook Pro with Nvidia graphics hardware say Y
+ to enable a driver for its backlight
+
+config BACKLIGHT_TOSA
+ tristate "Sharp SL-6000 Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && I2C
+ depends on MACH_TOSA && LCD_TOSA
+ default n
+ help
+ If you have an Sharp SL-6000 Zaurus say Y to enable a driver
+ for its backlight
+
+config BACKLIGHT_SAHARA
+ tristate "Tabletkiosk Sahara Touch-iT Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && X86
+ default n
+ help
+ If you have a Tabletkiosk Sahara Touch-iT, say y to enable the
+ backlight driver.
+
+config BACKLIGHT_WM831X
+ tristate "WM831x PMIC Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && MFD_WM831X
+ help
+ If you have a backlight driven by the ISINK and DCDC of a
+ WM831x PMIC say y to enable the backlight driver for it.
+
+config BACKLIGHT_ADX
+ tristate "Avionic Design Xanthos Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && ARCH_PXA_ADX
+ default y
+ help
+ Say Y to enable the backlight driver on Avionic Design Xanthos-based
+ boards.
+
+config BACKLIGHT_ADP5520
+ tristate "Backlight Driver for ADP5520/ADP5501 using WLED"
+ depends on BACKLIGHT_CLASS_DEVICE && PMIC_ADP5520
+ help
+ If you have a LCD backlight connected to the BST/BL_SNK output of
+ ADP5520 or ADP5501, say Y here to enable this driver.
+
+ To compile this driver as a module, choose M here: the module will
+ be called adp5520_bl.
+
+config BACKLIGHT_88PM860X
+ tristate "Backlight Driver for 88PM8606 using WLED"
+ depends on BACKLIGHT_CLASS_DEVICE && MFD_88PM860X
+ help
+ Say Y to enable the backlight driver for Marvell 88PM8606.
+
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff