To have support for your specific LCD panel you will have to
select the proper drivers which depend on this option.
+config LCD_CORGI
+ tristate "LCD Panel support for SHARP corgi/spitz model"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER && PXA_SHARPSL
+ help
+ Say y here to support the LCD panels usually found on SHARP
+ corgi (C7x0) and spitz (Cxx00) models.
+
+config LCD_L4F00242T03
+ tristate "Epson L4F00242T03 LCD"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER && GENERIC_GPIO
+ help
+ SPI driver for Epson L4F00242T03. This provides basic support
+ for init and powering the LCD up/down through a sysfs interface.
+
+config LCD_LMS283GF05
+ tristate "Samsung LMS283GF05 LCD"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER && GENERIC_GPIO
+ help
+ SPI driver for Samsung LMS283GF05. This provides basic support
+ for powering the LCD up/down through a sysfs interface.
+
config LCD_LTV350QV
tristate "Samsung LTV350QV LCD Panel"
depends on LCD_CLASS_DEVICE && SPI_MASTER
If you have a panel based on the ILI9320 controller chip
then say y to include a power driver for it.
+config LCD_TDO24M
+ tristate "Toppoly TDO24M and TDO35S LCD Panels support"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER
+ default n
+ help
+ If you have a Toppoly TDO24M/TDO35S series LCD panel, say y here to
+ include the support for it.
+
config LCD_VGG2432A4
tristate "VGG2432A4 LCM device support"
depends on BACKLIGHT_LCD_SUPPORT && LCD_CLASS_DEVICE && SPI_MASTER
If you have a VGG2432A4 panel based on the ILI9320 controller chip
then say y to include a power driver for it.
+config LCD_PLATFORM
+ tristate "Platform LCD controls"
+ depends on LCD_CLASS_DEVICE
+ help
+ This driver provides a platform-device registered LCD power
+ control interface.
+
+config LCD_TOSA
+ tristate "Sharp SL-6000 LCD Driver"
+ depends on LCD_CLASS_DEVICE && SPI
+ depends on MACH_TOSA
+ default n
+ help
+ If you have an Sharp SL-6000 Zaurus say Y to enable a driver
+ for its LCD.
+
+config LCD_HP700
+ tristate "HP Jornada 700 series LCD Driver"
+ depends on LCD_CLASS_DEVICE
+ depends on SA1100_JORNADA720_SSP && !PREEMPT
+ default y
+ help
+ If you have an HP Jornada 700 series handheld (710/720/728)
+ say Y to enable LCD control driver.
+
#
# Backlight
#
config BACKLIGHT_ATMEL_LCDC
bool "Atmel LCDC Contrast-as-Backlight control"
depends on BACKLIGHT_CLASS_DEVICE && FB_ATMEL
- default y if MACH_SAM9261EK || MACH_SAM9263EK
+ default y if MACH_SAM9261EK || MACH_SAM9G10EK || MACH_SAM9263EK
help
This provides a backlight control internal to the Atmel LCDC
driver. If the LCD "contrast control" on your board is wired
If in doubt, it's safe to enable this option; it doesn't kick
in unless the board's description says it's wired that way.
-config BACKLIGHT_CORGI
+config BACKLIGHT_ATMEL_PWM
+ tristate "Atmel PWM backlight control"
+ depends on BACKLIGHT_CLASS_DEVICE && ATMEL_PWM
+ default n
+ help
+ Say Y here if you want to use the PWM peripheral in Atmel AT91 and
+ AVR32 devices. This driver will need additional platform data to know
+ which PWM instance to use and how to configure it.
+
+ To compile this driver as a module, choose M here: the module will be
+ called atmel-pwm-bl.
+
+config BACKLIGHT_GENERIC
tristate "Generic (aka Sharp Corgi) Backlight Driver"
depends on BACKLIGHT_CLASS_DEVICE
- default n
+ default y
help
Say y to enable the generic platform backlight driver previously
known as the Corgi backlight driver. If you have a Sharp Zaurus
- SL-C7xx, SL-Cxx00 or SL-6000x say y. Most users can say n.
+ SL-C7xx, SL-Cxx00 or SL-6000x say y.
config BACKLIGHT_LOCOMO
tristate "Sharp LOCOMO LCD/Backlight Driver"
If you have a HP Jornada 680, say y to enable the
backlight driver.
+config BACKLIGHT_HP700
+ tristate "HP Jornada 700 series Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE
+ depends on SA1100_JORNADA720_SSP && !PREEMPT
+ default y
+ help
+ If you have an HP Jornada 700 series,
+ say Y to include backlight control driver.
+
config BACKLIGHT_PROGEAR
tristate "Frontpath ProGear Backlight Driver"
depends on BACKLIGHT_CLASS_DEVICE && PCI && X86
help
If you have a LCD backlight adjustable by PWM, say Y to enable
this driver.
+
+config BACKLIGHT_DA903X
+ tristate "Backlight Driver for DA9030/DA9034 using WLED"
+ depends on BACKLIGHT_CLASS_DEVICE && PMIC_DA903X
+ help
+ If you have a LCD backlight connected to the WLED output of DA9030
+ or DA9034 WLED output, say Y here to enable this driver.
+
+config BACKLIGHT_MAX8925
+ tristate "Backlight driver for MAX8925"
+ depends on BACKLIGHT_CLASS_DEVICE && MFD_MAX8925
+ help
+ If you have a LCD backlight connected to the WLED output of MAX8925
+ WLED output, say Y here to enable this driver.
+
+config BACKLIGHT_MBP_NVIDIA
+ tristate "MacBook Pro Nvidia Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && X86
+ default n
+ help
+ If you have an Apple Macbook Pro with Nvidia graphics hardware say Y
+ to enable a driver for its backlight
+
+config BACKLIGHT_TOSA
+ tristate "Sharp SL-6000 Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && I2C
+ depends on MACH_TOSA && LCD_TOSA
+ default n
+ help
+ If you have an Sharp SL-6000 Zaurus say Y to enable a driver
+ for its backlight
+
+config BACKLIGHT_SAHARA
+ tristate "Tabletkiosk Sahara Touch-iT Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && X86
+ default n
+ help
+ If you have a Tabletkiosk Sahara Touch-iT, say y to enable the
+ backlight driver.
+
+config BACKLIGHT_WM831X
+ tristate "WM831x PMIC Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && MFD_WM831X
+ help
+ If you have a backlight driven by the ISINK and DCDC of a
+ WM831x PMIC say y to enable the backlight driver for it.
+
+config BACKLIGHT_ADX
+ tristate "Avionic Design Xanthos Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && ARCH_PXA_ADX
+ default y
+ help
+ Say Y to enable the backlight driver on Avionic Design Xanthos-based
+ boards.
+
+config BACKLIGHT_ADP5520
+ tristate "Backlight Driver for ADP5520/ADP5501 using WLED"
+ depends on BACKLIGHT_CLASS_DEVICE && PMIC_ADP5520
+ help
+ If you have a LCD backlight connected to the BST/BL_SNK output of
+ ADP5520 or ADP5501, say Y here to enable this driver.
+
+ To compile this driver as a module, choose M here: the module will
+ be called adp5520_bl.
+
+config BACKLIGHT_88PM860X
+ tristate "Backlight Driver for 88PM8606 using WLED"
+ depends on BACKLIGHT_CLASS_DEVICE && MFD_88PM860X
+ help
+ Say Y to enable the backlight driver for Marvell 88PM8606.
+
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff