drm/radeon/rv740: fix backend setup

[safe/jmp/linux-2.6] / drivers / video / Kconfig

diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 7be5062..5a5c303 100644 (file)
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -5,6 +5,9 @@
 menu "Graphics support"
        depends on HAS_IOMEM
 
+config HAVE_FB_ATMEL
+       bool
+
 source "drivers/char/agp/Kconfig"
 
 source "drivers/gpu/vga/Kconfig"
@@ -611,6 +614,21 @@ config FB_BFIN_T350MCQB
         This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
         It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
 
+config FB_BFIN_LQ035Q1
+       tristate "SHARP LQ035Q1DH02 TFT LCD"
+       depends on FB && BLACKFIN && SPI
+       select FB_CFB_FILLRECT
+       select FB_CFB_COPYAREA
+       select FB_CFB_IMAGEBLIT
+       select BFIN_GPTIMERS
+       help
+         This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on
+         the Blackfin Landscape LCD EZ-Extender Card.
+         This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI
+         It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK.
+
+         To compile this driver as a module, choose M here: the
+         module will be called bfin-lq035q1-fb.
 
 config FB_STI
        tristate "HP STI frame buffer device support"
@@ -937,7 +955,7 @@ config FB_S1D13XXX
 
 config FB_ATMEL
        tristate "AT91/AT32 LCD Controller support"
-       depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9G10 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45 || ARCH_AT91CAP9 || AVR32)
+       depends on FB && HAVE_FB_ATMEL
        select FB_CFB_FILLRECT
        select FB_CFB_COPYAREA
        select FB_CFB_IMAGEBLIT
@@ -1275,26 +1293,6 @@ config FB_MATROX_MAVEN
          painting procedures (the secondary head does not use acceleration
          engine).
 
-config FB_MATROX_MULTIHEAD
-       bool "Multihead support"
-       depends on FB_MATROX
-       ---help---
-         Say Y here if you have more than one (supported) Matrox device in
-         your computer and you want to use all of them for different monitors
-         ("multihead"). If you have only one device, you should say N because
-         the driver compiled with Y is larger and a bit slower, especially on
-         ia32 (ix86).
-
-         If you said M to "Matrox unified accelerated driver" and N here, you
-         will still be able to use several Matrox devices simultaneously:
-         insert several instances of the module matroxfb into the kernel
-         with insmod, supplying the parameter "dev=N" where N is 0, 1, etc.
-         for the different Matrox devices. This method is slightly faster but
-         uses 40 KB of kernel memory per Matrox card.
-
-         There is no need for enabling 'Matrox multihead support' if you have
-         only one Matrox card in the box.
-
 config FB_RADEON
        tristate "ATI Radeon display support"
        depends on FB && PCI
@@ -2083,6 +2081,7 @@ config XEN_FBDEV_FRONTEND
        select FB_SYS_IMAGEBLIT
        select FB_SYS_FOPS
        select FB_DEFERRED_IO
+       select XEN_XENBUS_FRONTEND
        default y
        help
          This driver implements the front-end of the Xen virtual
@@ -2141,13 +2140,13 @@ config FB_EP93XX
 
 config FB_PRE_INIT_FB
        bool "Don't reinitialize, use bootloader's GDC/Display configuration"
-       depends on FB_MB862XX_LIME
+       depends on FB && FB_MB862XX_LIME
        ---help---
          Select this option if display contents should be inherited as set by
          the bootloader.
 
 config FB_MSM
-       tristate
+       tristate "MSM Framebuffer support"
        depends on FB && ARCH_MSM
        select FB_CFB_FILLRECT
        select FB_CFB_COPYAREA
@@ -2181,6 +2180,7 @@ config FB_BROADSHEET
          a bridge adapter.
 
 source "drivers/video/omap/Kconfig"
+source "drivers/video/omap2/Kconfig"
 
 source "drivers/video/backlight/Kconfig"
 source "drivers/video/display/Kconfig"