#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
+#include <linux/smp_lock.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
/*
* Version Information
*/
-#define DRIVER_VERSION "v1.4.3"
+#define DRIVER_VERSION "v1.5.0"
#define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com>, Bill Ryder <bryder@sgi.com>, Kuba Ober <kuba@mareimbrium.org>"
#define DRIVER_DESC "USB FTDI Serial Converters Driver"
static __u16 product;
struct ftdi_private {
+ struct kref kref;
ftdi_chip_type_t chip_type;
/* type of device, either SIO or FT8U232AM */
int baud_base; /* baud base clock for divisor setting */
struct delayed_work rx_work;
struct usb_serial_port *port;
int rx_processed;
- unsigned long rx_bytes;
- __u16 interface; /* FT2232C port interface (0 for FT232/245) */
+ __u16 interface; /* FT2232C, FT2232H or FT4232H port interface
+ (0 for FT232/245) */
speed_t force_baud; /* if non-zero, force the baud rate to
this value */
int force_rtscts; /* if non-zero, force RTS-CTS to always
be enabled */
+ unsigned int latency; /* latency setting in use */
spinlock_t tx_lock; /* spinlock for transmit state */
unsigned long tx_bytes;
unsigned long tx_outstanding_bytes;
unsigned long tx_outstanding_urbs;
+ unsigned short max_packet_size;
};
/* struct ftdi_sio_quirk is used by devices requiring special attention. */
static int ftdi_jtag_probe(struct usb_serial *serial);
static int ftdi_mtxorb_hack_setup(struct usb_serial *serial);
+static int ftdi_NDI_device_setup(struct usb_serial *serial);
static void ftdi_USB_UIRT_setup(struct ftdi_private *priv);
static void ftdi_HE_TIRA1_setup(struct ftdi_private *priv);
.probe = ftdi_mtxorb_hack_setup,
};
+static struct ftdi_sio_quirk ftdi_NDI_device_quirk = {
+ .probe = ftdi_NDI_device_setup,
+};
+
static struct ftdi_sio_quirk ftdi_USB_UIRT_quirk = {
.port_probe = ftdi_USB_UIRT_setup,
};
static struct usb_device_id id_table_combined [] = {
{ USB_DEVICE(FTDI_VID, FTDI_AMC232_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CANUSB_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_CANDAPTER_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_0_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_1_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SCS_DEVICE_2_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_232RL_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_8U2232C_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_4232H_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MICRO_CHAMELEON_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_RELAIS_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_OPENDCC_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_SNIFFER_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_THROTTLE_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GATEWAY_PID) },
{ USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_IOBOARD_PID) },
{ USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_MINI_IOBOARD_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_SPROG_II) },
{ USB_DEVICE(FTDI_VID, FTDI_XF_632_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_XF_634_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_XF_547_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MTXORB_4_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MTXORB_5_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MTXORB_6_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_R2000KU_TRUE_RNG) },
{ USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0100_PID) },
{ USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0101_PID) },
{ USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0102_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CCSICDU20_0_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CCSICDU40_1_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CCSMACHX_2_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_CCSLOAD_N_GO_3_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_CCSICDU64_4_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_CCSPRIME8_5_PID) },
{ USB_DEVICE(FTDI_VID, INSIDE_ACCESSO) },
{ USB_DEVICE(INTREPID_VID, INTREPID_VALUECAN_PID) },
{ USB_DEVICE(INTREPID_VID, INTREPID_NEOVI_PID) },
{ USB_DEVICE(FALCOM_VID, FALCOM_TWIST_PID) },
{ USB_DEVICE(FALCOM_VID, FALCOM_SAMBA_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SUUNTO_SPORTS_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_OCEANIC_PID) },
{ USB_DEVICE(TTI_VID, TTI_QL355P_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_RM_CANVIEW_PID) },
{ USB_DEVICE(BANDB_VID, BANDB_USOTL4_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_TACTRIX_OPENPORT_13S_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_TACTRIX_OPENPORT_13U_PID) },
{ USB_DEVICE(ELEKTOR_VID, ELEKTOR_FT323R_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_HUC_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_SPECTRA_SCU_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_FUTURE_2_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_FUTURE_3_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_AURORA_SCU_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
{ USB_DEVICE(TELLDUS_VID, TELLDUS_TELLSTICK_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MAXSTREAM_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_PHI_FISCO_PID) },
{ USB_DEVICE(TML_VID, TML_USB_SERIAL_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_ELSTER_UNICOM_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_PROPOX_JTAGCABLEII_PID) },
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(FTDI_VID, FTDI_OOCDLINK_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(FTDI_VID, LMI_LM3S_DEVEL_BOARD_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(FTDI_VID, LMI_LM3S_EVAL_BOARD_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_TURTELIZER_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(RATOC_VENDOR_ID, RATOC_PRODUCT_ID_USB60F) },
{ USB_DEVICE(FTDI_VID, FTDI_REU_TINY_PID) },
+ { USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO4x4_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_DOMINTELL_DGQG_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_DOMINTELL_DUSB_PID) },
+ { USB_DEVICE(ALTI2_VID, ALTI2_N3_PID) },
+ { USB_DEVICE(FTDI_VID, DIEBOLD_BCS_SE923_PID) },
+ { USB_DEVICE(ATMEL_VID, STK541_PID) },
+ { USB_DEVICE(DE_VID, STB_PID) },
+ { USB_DEVICE(DE_VID, WHT_PID) },
+ { USB_DEVICE(ADI_VID, ADI_GNICE_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(ADI_VID, ADI_GNICEPLUS_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(JETI_VID, JETI_SPC1201_PID) },
+ { USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) },
+ { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) },
+ { USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) },
+ { USB_DEVICE(FTDI_VID, MARVELL_OPENRD_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(FTDI_VID, HAMEG_HO820_PID) },
+ { USB_DEVICE(FTDI_VID, HAMEG_HO870_PID) },
{ }, /* Optional parameter entry */
{ } /* Terminating entry */
};
[FT232BM] = "FT232BM",
[FT2232C] = "FT2232C",
[FT232RL] = "FT232RL",
+ [FT2232H] = "FT2232H",
+ [FT4232H] = "FT4232H"
};
/* Constants for read urb and write urb */
#define BUFSZ 512
-#define PKTSZ 64
/* rx_flags */
#define THROTTLED 0x01
/* function prototypes for a FTDI serial converter */
static int ftdi_sio_probe(struct usb_serial *serial,
const struct usb_device_id *id);
-static void ftdi_shutdown(struct usb_serial *serial);
static int ftdi_sio_port_probe(struct usb_serial_port *port);
static int ftdi_sio_port_remove(struct usb_serial_port *port);
-static int ftdi_open(struct tty_struct *tty,
- struct usb_serial_port *port, struct file *filp);
-static void ftdi_close(struct tty_struct *tty,
- struct usb_serial_port *port, struct file *filp);
+static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port);
+static void ftdi_close(struct usb_serial_port *port);
+static void ftdi_dtr_rts(struct usb_serial_port *port, int on);
static int ftdi_write(struct tty_struct *tty, struct usb_serial_port *port,
const unsigned char *buf, int count);
static int ftdi_write_room(struct tty_struct *tty);
static unsigned short int ftdi_232am_baud_to_divisor(int baud);
static __u32 ftdi_232bm_baud_base_to_divisor(int baud, int base);
static __u32 ftdi_232bm_baud_to_divisor(int baud);
+static __u32 ftdi_2232h_baud_base_to_divisor(int baud, int base);
+static __u32 ftdi_2232h_baud_to_divisor(int baud);
static struct usb_serial_driver ftdi_sio_device = {
.driver = {
.port_remove = ftdi_sio_port_remove,
.open = ftdi_open,
.close = ftdi_close,
+ .dtr_rts = ftdi_dtr_rts,
.throttle = ftdi_throttle,
.unthrottle = ftdi_unthrottle,
.write = ftdi_write,
.ioctl = ftdi_ioctl,
.set_termios = ftdi_set_termios,
.break_ctl = ftdi_break_ctl,
- .shutdown = ftdi_shutdown,
};
return ftdi_232bm_baud_base_to_divisor(baud, 48000000);
}
+static __u32 ftdi_2232h_baud_base_to_divisor(int baud, int base)
+{
+ static const unsigned char divfrac[8] = { 0, 3, 2, 4, 1, 5, 6, 7 };
+ __u32 divisor;
+ int divisor3;
+
+ /* hi-speed baud rate is 10-bit sampling instead of 16-bit */
+ divisor3 = (base / 10 / baud) * 8;
+
+ divisor = divisor3 >> 3;
+ divisor |= (__u32)divfrac[divisor3 & 0x7] << 14;
+ /* Deal with special cases for highest baud rates. */
+ if (divisor == 1)
+ divisor = 0;
+ else if (divisor == 0x4001)
+ divisor = 1;
+ /*
+ * Set this bit to turn off a divide by 2.5 on baud rate generator
+ * This enables baud rates up to 12Mbaud but cannot reach below 1200
+ * baud with this bit set
+ */
+ divisor |= 0x00020000;
+ return divisor;
+}
+
+static __u32 ftdi_2232h_baud_to_divisor(int baud)
+{
+ return ftdi_2232h_baud_base_to_divisor(baud, 120000000);
+}
+
#define set_mctrl(port, set) update_mctrl((port), (set), 0)
#define clear_mctrl(port, clear) update_mctrl((port), 0, (clear))
kfree(buf);
if (rv < 0) {
- err("%s Error from MODEM_CTRL urb: DTR %s, RTS %s",
+ dbg("%s Error from MODEM_CTRL urb: DTR %s, RTS %s",
__func__,
(set & TIOCM_DTR) ? "HIGH" :
(clear & TIOCM_DTR) ? "LOW" : "unchanged",
case FT2232C: /* FT2232C chip */
case FT232RL:
if (baud <= 3000000) {
+ __u16 product_id = le16_to_cpu(
+ port->serial->dev->descriptor.idProduct);
+ if (((FTDI_NDI_HUC_PID == product_id) ||
+ (FTDI_NDI_SPECTRA_SCU_PID == product_id) ||
+ (FTDI_NDI_FUTURE_2_PID == product_id) ||
+ (FTDI_NDI_FUTURE_3_PID == product_id) ||
+ (FTDI_NDI_AURORA_SCU_PID == product_id)) &&
+ (baud == 19200)) {
+ baud = 1200000;
+ }
+ div_value = ftdi_232bm_baud_to_divisor(baud);
+ } else {
+ dbg("%s - Baud rate too high!", __func__);
+ div_value = ftdi_232bm_baud_to_divisor(9600);
+ div_okay = 0;
+ baud = 9600;
+ }
+ break;
+ case FT2232H: /* FT2232H chip */
+ case FT4232H: /* FT4232H chip */
+ if ((baud <= 12000000) & (baud >= 1200)) {
+ div_value = ftdi_2232h_baud_to_divisor(baud);
+ } else if (baud < 1200) {
div_value = ftdi_232bm_baud_to_divisor(baud);
} else {
dbg("%s - Baud rate too high!", __func__);
return rv;
}
+static int write_latency_timer(struct usb_serial_port *port)
+{
+ struct ftdi_private *priv = usb_get_serial_port_data(port);
+ struct usb_device *udev = port->serial->dev;
+ char buf[1];
+ int rv = 0;
+ int l = priv->latency;
+
+ if (priv->flags & ASYNC_LOW_LATENCY)
+ l = 1;
+
+ dbg("%s: setting latency timer = %i", __func__, l);
+
+ rv = usb_control_msg(udev,
+ usb_sndctrlpipe(udev, 0),
+ FTDI_SIO_SET_LATENCY_TIMER_REQUEST,
+ FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE,
+ l, priv->interface,
+ buf, 0, WDR_TIMEOUT);
+
+ if (rv < 0)
+ dev_err(&port->dev, "Unable to write latency timer: %i\n", rv);
+ return rv;
+}
+
+static int read_latency_timer(struct usb_serial_port *port)
+{
+ struct ftdi_private *priv = usb_get_serial_port_data(port);
+ struct usb_device *udev = port->serial->dev;
+ unsigned short latency = 0;
+ int rv = 0;
+
+
+ dbg("%s", __func__);
+
+ rv = usb_control_msg(udev,
+ usb_rcvctrlpipe(udev, 0),
+ FTDI_SIO_GET_LATENCY_TIMER_REQUEST,
+ FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE,
+ 0, priv->interface,
+ (char *) &latency, 1, WDR_TIMEOUT);
+ if (rv < 0) {
+ dev_err(&port->dev, "Unable to read latency timer: %i\n", rv);
+ return -EIO;
+ }
+ return latency;
+}
static int get_serial_info(struct usb_serial_port *port,
struct serial_struct __user *retinfo)
if (copy_from_user(&new_serial, newinfo, sizeof(new_serial)))
return -EFAULT;
+
+ lock_kernel();
old_priv = *priv;
/* Do error checking and permission checking */
if (!capable(CAP_SYS_ADMIN)) {
if (((new_serial.flags & ~ASYNC_USR_MASK) !=
- (priv->flags & ~ASYNC_USR_MASK)))
+ (priv->flags & ~ASYNC_USR_MASK))) {
+ unlock_kernel();
return -EPERM;
+ }
priv->flags = ((priv->flags & ~ASYNC_USR_MASK) |
(new_serial.flags & ASYNC_USR_MASK));
priv->custom_divisor = new_serial.custom_divisor;
}
if ((new_serial.baud_base != priv->baud_base) &&
- (new_serial.baud_base < 9600))
+ (new_serial.baud_base < 9600)) {
+ unlock_kernel();
return -EINVAL;
+ }
/* Make the changes - these are privileged changes! */
(new_serial.flags & ASYNC_FLAGS));
priv->custom_divisor = new_serial.custom_divisor;
- tty->low_latency = (priv->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
+ write_latency_timer(port);
check_and_exit:
if ((old_priv.flags & ASYNC_SPD_MASK) !=
(priv->flags & ASYNC_SPD_MASK)) ||
(((priv->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) &&
(old_priv.custom_divisor != priv->custom_divisor))) {
+ unlock_kernel();
change_speed(tty, port);
}
+ else
+ unlock_kernel();
return 0;
} /* set_serial_info */
if (interfaces > 1) {
int inter;
- /* Multiple interfaces. Assume FT2232C. */
- priv->chip_type = FT2232C;
+ /* Multiple interfaces.*/
+ if (version == 0x0800) {
+ priv->chip_type = FT4232H;
+ /* Hi-speed - baud clock runs at 120MHz */
+ priv->baud_base = 120000000 / 2;
+ } else if (version == 0x0700) {
+ priv->chip_type = FT2232H;
+ /* Hi-speed - baud clock runs at 120MHz */
+ priv->baud_base = 120000000 / 2;
+ } else
+ priv->chip_type = FT2232C;
+
/* Determine interface code. */
inter = serial->interface->altsetting->desc.bInterfaceNumber;
- if (inter == 0)
- priv->interface = PIT_SIOA;
- else
- priv->interface = PIT_SIOB;
+ if (inter == 0) {
+ priv->interface = INTERFACE_A;
+ } else if (inter == 1) {
+ priv->interface = INTERFACE_B;
+ } else if (inter == 2) {
+ priv->interface = INTERFACE_C;
+ } else if (inter == 3) {
+ priv->interface = INTERFACE_D;
+ }
/* BM-type devices have a bug where bcdDevice gets set
* to 0x200 when iSerialNumber is 0. */
if (version < 0x500) {
/* Assume its an FT232R */
priv->chip_type = FT232RL;
}
- info("Detected %s", ftdi_chip_name[priv->chip_type]);
+ dev_info(&udev->dev, "Detected %s\n", ftdi_chip_name[priv->chip_type]);
+}
+
+
+/* Determine the maximum packet size for the device. This depends on the chip
+ * type and the USB host capabilities. The value should be obtained from the
+ * device descriptor as the chip will use the appropriate values for the host.*/
+static void ftdi_set_max_packet_size(struct usb_serial_port *port)
+{
+ struct ftdi_private *priv = usb_get_serial_port_data(port);
+ struct usb_serial *serial = port->serial;
+ struct usb_device *udev = serial->dev;
+
+ struct usb_interface *interface = serial->interface;
+ struct usb_endpoint_descriptor *ep_desc = &interface->cur_altsetting->endpoint[1].desc;
+
+ unsigned num_endpoints;
+ int i = 0;
+
+ num_endpoints = interface->cur_altsetting->desc.bNumEndpoints;
+ dev_info(&udev->dev, "Number of endpoints %d\n", num_endpoints);
+
+ /* NOTE: some customers have programmed FT232R/FT245R devices
+ * with an endpoint size of 0 - not good. In this case, we
+ * want to override the endpoint descriptor setting and use a
+ * value of 64 for wMaxPacketSize */
+ for (i = 0; i < num_endpoints; i++) {
+ dev_info(&udev->dev, "Endpoint %d MaxPacketSize %d\n", i+1,
+ interface->cur_altsetting->endpoint[i].desc.wMaxPacketSize);
+ ep_desc = &interface->cur_altsetting->endpoint[i].desc;
+ if (ep_desc->wMaxPacketSize == 0) {
+ ep_desc->wMaxPacketSize = cpu_to_le16(0x40);
+ dev_info(&udev->dev, "Overriding wMaxPacketSize on endpoint %d\n", i);
+ }
+ }
+
+ /* set max packet size based on descriptor */
+ priv->max_packet_size = ep_desc->wMaxPacketSize;
+
+ dev_info(&udev->dev, "Setting MaxPacketSize %d\n", priv->max_packet_size);
}
{
struct usb_serial_port *port = to_usb_serial_port(dev);
struct ftdi_private *priv = usb_get_serial_port_data(port);
- struct usb_device *udev = port->serial->dev;
- unsigned short latency = 0;
- int rv = 0;
-
-
- dbg("%s", __func__);
-
- rv = usb_control_msg(udev,
- usb_rcvctrlpipe(udev, 0),
- FTDI_SIO_GET_LATENCY_TIMER_REQUEST,
- FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE,
- 0, priv->interface,
- (char *) &latency, 1, WDR_TIMEOUT);
-
- if (rv < 0) {
- dev_err(dev, "Unable to read latency timer: %i\n", rv);
- return -EIO;
- }
- return sprintf(buf, "%i\n", latency);
+ if (priv->flags & ASYNC_LOW_LATENCY)
+ return sprintf(buf, "1\n");
+ else
+ return sprintf(buf, "%i\n", priv->latency);
}
+
/* Write a new value of the latency timer, in units of milliseconds. */
static ssize_t store_latency_timer(struct device *dev,
struct device_attribute *attr, const char *valbuf,
{
struct usb_serial_port *port = to_usb_serial_port(dev);
struct ftdi_private *priv = usb_get_serial_port_data(port);
- struct usb_device *udev = port->serial->dev;
- char buf[1];
int v = simple_strtoul(valbuf, NULL, 10);
int rv = 0;
- dbg("%s: setting latency timer = %i", __func__, v);
-
- rv = usb_control_msg(udev,
- usb_sndctrlpipe(udev, 0),
- FTDI_SIO_SET_LATENCY_TIMER_REQUEST,
- FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE,
- v, priv->interface,
- buf, 0, WDR_TIMEOUT);
-
- if (rv < 0) {
- dev_err(dev, "Unable to write latency timer: %i\n", rv);
+ priv->latency = v;
+ rv = write_latency_timer(port);
+ if (rv < 0)
return -EIO;
- }
-
return count;
}
if ((!retval) &&
(priv->chip_type == FT232BM ||
priv->chip_type == FT2232C ||
- priv->chip_type == FT232RL)) {
+ priv->chip_type == FT232RL ||
+ priv->chip_type == FT2232H ||
+ priv->chip_type == FT4232H)) {
retval = device_create_file(&port->dev,
&dev_attr_latency_timer);
}
device_remove_file(&port->dev, &dev_attr_event_char);
if (priv->chip_type == FT232BM ||
priv->chip_type == FT2232C ||
- priv->chip_type == FT232RL) {
+ priv->chip_type == FT232RL ||
+ priv->chip_type == FT2232H ||
+ priv->chip_type == FT4232H) {
device_remove_file(&port->dev, &dev_attr_latency_timer);
}
}
priv = kzalloc(sizeof(struct ftdi_private), GFP_KERNEL);
if (!priv) {
- err("%s- kmalloc(%Zd) failed.", __func__,
+ dev_err(&port->dev, "%s- kmalloc(%Zd) failed.\n", __func__,
sizeof(struct ftdi_private));
return -ENOMEM;
}
+ kref_init(&priv->kref);
spin_lock_init(&priv->rx_lock);
spin_lock_init(&priv->tx_lock);
init_waitqueue_head(&priv->delta_msr_wait);
usb_set_serial_port_data(port, priv);
ftdi_determine_type(port);
+ ftdi_set_max_packet_size(port);
+ read_latency_timer(port);
create_sysfs_attrs(port);
return 0;
}
} /* ftdi_HE_TIRA1_setup */
/*
+ * Module parameter to control latency timer for NDI FTDI-based USB devices.
+ * If this value is not set in modprobe.conf.local its value will be set to 1ms.
+ */
+static int ndi_latency_timer = 1;
+
+/* Setup for the NDI FTDI-based USB devices, which requires hardwired
+ * baudrate (19200 gets mapped to 1200000).
+ *
+ * Called from usbserial:serial_probe.
+ */
+static int ftdi_NDI_device_setup(struct usb_serial *serial)
+{
+ struct usb_device *udev = serial->dev;
+ int latency = ndi_latency_timer;
+ int rv = 0;
+ char buf[1];
+
+ if (latency == 0)
+ latency = 1;
+ if (latency > 99)
+ latency = 99;
+
+ dbg("%s setting NDI device latency to %d", __func__, latency);
+ dev_info(&udev->dev, "NDI device with a latency value of %d", latency);
+
+ rv = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
+ FTDI_SIO_SET_LATENCY_TIMER_REQUEST,
+ FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE,
+ latency, 0, buf, 0, WDR_TIMEOUT);
+ return 0;
+}
+
+/*
* First port on JTAG adaptors such as Olimex arm-usb-ocd or the FIC/OpenMoko
* Neo1973 Debug Board is reserved for JTAG interface and can be accessed from
* userspace using openocd.
dbg("%s", __func__);
if (interface == udev->actconfig->interface[0]) {
- info("Ignoring serial port reserved for JTAG");
+ dev_info(&udev->dev,
+ "Ignoring serial port reserved for JTAG\n");
return -ENODEV;
}
if (ep->enabled && ep_desc->wMaxPacketSize == 0) {
ep_desc->wMaxPacketSize = cpu_to_le16(0x40);
- info("Fixing invalid wMaxPacketSize on read pipe");
+ dev_info(&serial->dev->dev,
+ "Fixing invalid wMaxPacketSize on read pipe\n");
}
return 0;
}
-/* ftdi_shutdown is called from usbserial:usb_serial_disconnect
- * it is called when the usb device is disconnected
- *
- * usbserial:usb_serial_disconnect
- * calls __serial_close for each open of the port
- * shutdown is called then (ie ftdi_shutdown)
- */
-static void ftdi_shutdown(struct usb_serial *serial)
+static void ftdi_sio_priv_release(struct kref *k)
{
- dbg("%s", __func__);
+ struct ftdi_private *priv = container_of(k, struct ftdi_private, kref);
+
+ kfree(priv);
}
static int ftdi_sio_port_remove(struct usb_serial_port *port)
remove_sysfs_attrs(port);
- /* all open ports are closed at this point
- * (by usbserial.c:__serial_close, which calls ftdi_close)
- */
-
- if (priv) {
- usb_set_serial_port_data(port, NULL);
- kfree(priv);
- }
+ kref_put(&priv->kref, ftdi_sio_priv_release);
return 0;
}
-static int ftdi_open(struct tty_struct *tty,
- struct usb_serial_port *port, struct file *filp)
+static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port)
{ /* ftdi_open */
struct usb_device *dev = port->serial->dev;
struct ftdi_private *priv = usb_get_serial_port_data(port);
spin_lock_irqsave(&priv->tx_lock, flags);
priv->tx_bytes = 0;
spin_unlock_irqrestore(&priv->tx_lock, flags);
- spin_lock_irqsave(&priv->rx_lock, flags);
- priv->rx_bytes = 0;
- spin_unlock_irqrestore(&priv->rx_lock, flags);
- if (tty)
- tty->low_latency = (priv->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
+ write_latency_timer(port);
/* No error checking for this (will get errors later anyway) */
/* See ftdi_sio.h for description of what is reset */
priv->interface, buf, 0, WDR_TIMEOUT);
/* Termios defaults are set by usb_serial_init. We don't change
- port->tty->termios - this would loose speed settings, etc.
+ port->tty->termios - this would lose speed settings, etc.
This is same behaviour as serial.c/rs_open() - Kuba */
/* ftdi_set_termios will send usb control messages */
if (tty)
ftdi_set_termios(tty, port, tty->termios);
- /* FIXME: Flow control might be enabled, so it should be checked -
- we have no control of defaults! */
- /* Turn on RTS and DTR since we are not flow controlling by default */
- set_mctrl(port, TIOCM_DTR | TIOCM_RTS);
-
/* Not throttled */
spin_lock_irqsave(&priv->rx_lock, flags);
priv->rx_flags &= ~(THROTTLED | ACTUALLY_THROTTLED);
ftdi_read_bulk_callback, port);
result = usb_submit_urb(port->read_urb, GFP_KERNEL);
if (result)
- err("%s - failed submitting read urb, error %d",
- __func__, result);
-
+ dev_err(&port->dev,
+ "%s - failed submitting read urb, error %d\n",
+ __func__, result);
+ else
+ kref_get(&priv->kref);
return result;
} /* ftdi_open */
+static void ftdi_dtr_rts(struct usb_serial_port *port, int on)
+{
+ struct ftdi_private *priv = usb_get_serial_port_data(port);
+ char buf[1];
+
+ mutex_lock(&port->serial->disc_mutex);
+ if (!port->serial->disconnected) {
+ /* Disable flow control */
+ if (!on && usb_control_msg(port->serial->dev,
+ usb_sndctrlpipe(port->serial->dev, 0),
+ FTDI_SIO_SET_FLOW_CTRL_REQUEST,
+ FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE,
+ 0, priv->interface, buf, 0,
+ WDR_TIMEOUT) < 0) {
+ dev_err(&port->dev, "error from flowcontrol urb\n");
+ }
+ /* drop RTS and DTR */
+ if (on)
+ set_mctrl(port, TIOCM_DTR | TIOCM_RTS);
+ else
+ clear_mctrl(port, TIOCM_DTR | TIOCM_RTS);
+ }
+ mutex_unlock(&port->serial->disc_mutex);
+}
/*
* usbserial:__serial_close only calls ftdi_close if the point is open
*
*/
-static void ftdi_close(struct tty_struct *tty,
- struct usb_serial_port *port, struct file *filp)
+static void ftdi_close(struct usb_serial_port *port)
{ /* ftdi_close */
- unsigned int c_cflag = tty->termios->c_cflag;
struct ftdi_private *priv = usb_get_serial_port_data(port);
- char buf[1];
dbg("%s", __func__);
- mutex_lock(&port->serial->disc_mutex);
- if (c_cflag & HUPCL && !port->serial->disconnected) {
- /* Disable flow control */
- if (usb_control_msg(port->serial->dev,
- usb_sndctrlpipe(port->serial->dev, 0),
- FTDI_SIO_SET_FLOW_CTRL_REQUEST,
- FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE,
- 0, priv->interface, buf, 0,
- WDR_TIMEOUT) < 0) {
- err("error from flowcontrol urb");
- }
-
- /* drop RTS and DTR */
- clear_mctrl(port, TIOCM_DTR | TIOCM_RTS);
- } /* Note change no line if hupcl is off */
- mutex_unlock(&port->serial->disc_mutex);
/* cancel any scheduled reading */
- cancel_delayed_work(&priv->rx_work);
- flush_scheduled_work();
+ cancel_delayed_work_sync(&priv->rx_work);
/* shutdown our bulk read */
usb_kill_urb(port->read_urb);
+ kref_put(&priv->kref, ftdi_sio_priv_release);
} /* ftdi_close */
if (data_offset > 0) {
/* Original sio needs control bytes too... */
transfer_size += (data_offset *
- ((count + (PKTSZ - 1 - data_offset)) /
- (PKTSZ - data_offset)));
+ ((count + (priv->max_packet_size - 1 - data_offset)) /
+ (priv->max_packet_size - data_offset)));
}
buffer = kmalloc(transfer_size, GFP_ATOMIC);
if (!buffer) {
- err("%s ran out of kernel memory for urb ...", __func__);
+ dev_err(&port->dev,
+ "%s ran out of kernel memory for urb ...\n", __func__);
count = -ENOMEM;
goto error_no_buffer;
}
urb = usb_alloc_urb(0, GFP_ATOMIC);
if (!urb) {
- err("%s - no more free urbs", __func__);
+ dev_err(&port->dev, "%s - no more free urbs\n", __func__);
count = -ENOMEM;
goto error_no_urb;
}
if (data_offset > 0) {
/* Original sio requires control byte at start of
each packet. */
- int user_pktsz = PKTSZ - data_offset;
+ int user_pktsz = priv->max_packet_size - data_offset;
int todo = count;
unsigned char *first_byte = buffer;
const unsigned char *current_position = buf;
status = usb_submit_urb(urb, GFP_ATOMIC);
if (status) {
- err("%s - failed submitting write urb, error %d",
- __func__, status);
+ dev_err(&port->dev,
+ "%s - failed submitting write urb, error %d\n",
+ __func__, status);
count = status;
goto error;
} else {
dbg("%s - port %d", __func__, port->number);
- if (status) {
- dbg("nonzero write bulk status received: %d", status);
- return;
- }
-
priv = usb_get_serial_port_data(port);
if (!priv) {
dbg("%s - bad port private data pointer - exiting", __func__);
data_offset = priv->write_offset;
if (data_offset > 0) {
/* Subtract the control bytes */
- countback -= (data_offset * DIV_ROUND_UP(countback, PKTSZ));
+ countback -= (data_offset * DIV_ROUND_UP(countback, priv->max_packet_size));
}
spin_lock_irqsave(&priv->tx_lock, flags);
--priv->tx_outstanding_urbs;
priv->tx_outstanding_bytes -= countback;
spin_unlock_irqrestore(&priv->tx_lock, flags);
+ if (status) {
+ dbg("nonzero write bulk status received: %d", status);
+ return;
+ }
+
usb_serial_port_softint(port);
} /* ftdi_write_bulk_callback */
buffered = (int)priv->tx_outstanding_bytes;
spin_unlock_irqrestore(&priv->tx_lock, flags);
if (buffered < 0) {
- err("%s outstanding tx bytes is negative!", __func__);
+ dev_err(&port->dev, "%s outstanding tx bytes is negative!\n",
+ __func__);
buffered = 0;
}
return buffered;
struct usb_serial_port *port = urb->context;
struct tty_struct *tty;
struct ftdi_private *priv;
- unsigned long countread;
- unsigned long flags;
int status = urb->status;
if (urb->number_of_packets > 0) {
- err("%s transfer_buffer_length %d actual_length %d number of packets %d",
- __func__,
- urb->transfer_buffer_length,
- urb->actual_length, urb->number_of_packets);
- err("%s transfer_flags %x ", __func__, urb->transfer_flags);
+ dev_err(&port->dev, "%s transfer_buffer_length %d "
+ "actual_length %d number of packets %d\n", __func__,
+ urb->transfer_buffer_length,
+ urb->actual_length, urb->number_of_packets);
+ dev_err(&port->dev, "%s transfer_flags %x\n", __func__,
+ urb->transfer_flags);
}
dbg("%s - port %d", __func__, port->number);
if (port->port.count <= 0)
return;
- tty = port->port.tty;
+ tty = tty_port_tty_get(&port->port);
if (!tty) {
dbg("%s - bad tty pointer - exiting", __func__);
return;
priv = usb_get_serial_port_data(port);
if (!priv) {
dbg("%s - bad port private data pointer - exiting", __func__);
- return;
+ goto out;
}
if (urb != port->read_urb)
- err("%s - Not my urb!", __func__);
+ dev_err(&port->dev, "%s - Not my urb!\n", __func__);
if (status) {
/* This will happen at close every time so it is a dbg not an
err */
dbg("(this is ok on close) nonzero read bulk status received: %d", status);
- return;
+ goto out;
}
- /* count data bytes, but not status bytes */
- countread = urb->actual_length;
- countread -= 2 * DIV_ROUND_UP(countread, PKTSZ);
- spin_lock_irqsave(&priv->rx_lock, flags);
- priv->rx_bytes += countread;
- spin_unlock_irqrestore(&priv->rx_lock, flags);
-
ftdi_process_read(&priv->rx_work.work);
-
+out:
+ tty_kref_put(tty);
} /* ftdi_read_bulk_callback */
if (port->port.count <= 0)
return;
- tty = port->port.tty;
+ tty = tty_port_tty_get(&port->port);
if (!tty) {
dbg("%s - bad tty pointer - exiting", __func__);
return;
priv = usb_get_serial_port_data(port);
if (!priv) {
dbg("%s - bad port private data pointer - exiting", __func__);
- return;
+ goto out;
}
urb = port->read_urb;
if (!urb) {
dbg("%s - bad read_urb pointer - exiting", __func__);
- return;
+ goto out;
}
data = urb->transfer_buffer;
need_flip = 0;
for (packet_offset = priv->rx_processed;
- packet_offset < urb->actual_length; packet_offset += PKTSZ) {
+ packet_offset < urb->actual_length; packet_offset += priv->max_packet_size) {
int length;
/* Compare new line status to the old one, signal if different/
N.B. packet may be processed more than once, but differences
are only processed once. */
- if (priv != NULL) {
- char new_status = data[packet_offset + 0] &
- FTDI_STATUS_B0_MASK;
- if (new_status != priv->prev_status) {
- priv->diff_status |=
- new_status ^ priv->prev_status;
- wake_up_interruptible(&priv->delta_msr_wait);
- priv->prev_status = new_status;
- }
+ char new_status = data[packet_offset + 0] &
+ FTDI_STATUS_B0_MASK;
+ if (new_status != priv->prev_status) {
+ priv->diff_status |=
+ new_status ^ priv->prev_status;
+ wake_up_interruptible(&priv->delta_msr_wait);
+ priv->prev_status = new_status;
}
- length = min(PKTSZ, urb->actual_length-packet_offset)-2;
+ length = min_t(u32, priv->max_packet_size, urb->actual_length-packet_offset)-2;
if (length < 0) {
- err("%s - bad packet length: %d", __func__, length+2);
+ dev_err(&port->dev, "%s - bad packet length: %d\n",
+ __func__, length+2);
length = 0;
}
if (data[packet_offset+1] & FTDI_RS_BI) {
error_flag = TTY_BREAK;
dbg("BREAK received");
+ usb_serial_handle_break(port);
}
if (data[packet_offset+1] & FTDI_RS_PE) {
error_flag = TTY_PARITY;
/* Note that the error flag is duplicated for
every character received since we don't know
which character it applied to */
- tty_insert_flip_char(tty,
- data[packet_offset + i], error_flag);
+ if (!usb_serial_handle_sysrq_char(tty, port,
+ data[packet_offset + i]))
+ tty_insert_flip_char(tty,
+ data[packet_offset + i],
+ error_flag);
}
need_flip = 1;
}
spin_unlock_irqrestore(&priv->rx_lock, flags);
dbg("%s - deferring remainder until unthrottled",
__func__);
- return;
+ goto out;
}
spin_unlock_irqrestore(&priv->rx_lock, flags);
/* if the port is closed stop trying to read */
schedule_delayed_work(&priv->rx_work, 1);
else
dbg("%s - port is closed", __func__);
- return;
+ goto out;
}
/* urb is completely processed */
result = usb_submit_urb(port->read_urb, GFP_ATOMIC);
if (result)
- err("%s - failed resubmitting read urb, error %d",
- __func__, result);
+ dev_err(&port->dev,
+ "%s - failed resubmitting read urb, error %d\n",
+ __func__, result);
}
+out:
+ tty_kref_put(tty);
} /* ftdi_process_read */
FTDI_SIO_SET_DATA_REQUEST_TYPE,
urb_value , priv->interface,
buf, 0, WDR_TIMEOUT) < 0) {
- err("%s FAILED to enable/disable break state (state was %d)",
- __func__, break_state);
+ dev_err(&port->dev, "%s FAILED to enable/disable break state "
+ "(state was %d)\n", __func__, break_state);
}
dbg("%s break state is %d - urb is %d", __func__,
case CS7: urb_value |= 7; dbg("Setting CS7"); break;
case CS8: urb_value |= 8; dbg("Setting CS8"); break;
default:
- err("CSIZE was set but not CS5-CS8");
+ dev_err(&port->dev, "CSIZE was set but not CS5-CS8\n");
}
}
FTDI_SIO_SET_DATA_REQUEST_TYPE,
urb_value , priv->interface,
buf, 0, WDR_SHORT_TIMEOUT) < 0) {
- err("%s FAILED to set databits/stopbits/parity", __func__);
+ dev_err(&port->dev, "%s FAILED to set "
+ "databits/stopbits/parity\n", __func__);
}
/* Now do the baudrate */
FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE,
0, priv->interface,
buf, 0, WDR_TIMEOUT) < 0) {
- err("%s error from disable flowcontrol urb", __func__);
+ dev_err(&port->dev,
+ "%s error from disable flowcontrol urb\n",
+ __func__);
}
/* Drop RTS and DTR */
clear_mctrl(port, TIOCM_DTR | TIOCM_RTS);
} else {
/* set the baudrate determined before */
if (change_speed(tty, port))
- err("%s urb failed to set baudrate", __func__);
+ dev_err(&port->dev, "%s urb failed to set baudrate\n",
+ __func__);
/* Ensure RTS and DTR are raised when baudrate changed from 0 */
if (!old_termios || (old_termios->c_cflag & CBAUD) == B0)
set_mctrl(port, TIOCM_DTR | TIOCM_RTS);
FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE,
0 , (FTDI_SIO_RTS_CTS_HS | priv->interface),
buf, 0, WDR_TIMEOUT) < 0) {
- err("urb failed to set to rts/cts flow control");
+ dev_err(&port->dev,
+ "urb failed to set to rts/cts flow control\n");
}
} else {
urb_value , (FTDI_SIO_XON_XOFF_HS
| priv->interface),
buf, 0, WDR_TIMEOUT) < 0) {
- err("urb failed to set to xon/xoff flow control");
+ dev_err(&port->dev, "urb failed to set to "
+ "xon/xoff flow control\n");
}
} else {
/* else clause to only run if cflag ! CRTSCTS and iflag
FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE,
0, priv->interface,
buf, 0, WDR_TIMEOUT) < 0) {
- err("urb failed to clear flow control");
+ dev_err(&port->dev,
+ "urb failed to clear flow control\n");
}
}
FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE,
0, 0,
buf, 1, WDR_TIMEOUT);
- if (ret < 0) {
- err("%s Could not get modem status of device - err: %d", __func__,
- ret);
+ if (ret < 0)
return ret;
- }
break;
case FT8U232AM:
case FT232BM:
case FT2232C:
case FT232RL:
+ case FT2232H:
+ case FT4232H:
/* the 8U232AM returns a two byte value (the sio is a 1 byte
value) - in the same format as the data returned from the in
point */
FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE,
0, priv->interface,
buf, 2, WDR_TIMEOUT);
- if (ret < 0) {
- err("%s Could not get modem status of device - err: %d", __func__,
- ret);
+ if (ret < 0)
return ret;
- }
break;
default:
return -EFAULT;
- break;
}
return (buf[0] & FTDI_SIO_DSR_MASK ? TIOCM_DSR : 0) |
if (retval)
goto failed_usb_register;
- info(DRIVER_VERSION ":" DRIVER_DESC);
+ printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":"
+ DRIVER_DESC "\n");
return 0;
failed_usb_register:
usb_serial_deregister(&ftdi_sio_device);
MODULE_PARM_DESC(vendor, "User specified vendor ID (default="
__MODULE_STRING(FTDI_VID)")");
module_param(product, ushort, 0);
-MODULE_PARM_DESC(vendor, "User specified product ID");
+MODULE_PARM_DESC(product, "User specified product ID");
+module_param(ndi_latency_timer, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(ndi_latency_timer, "NDI device latency timer override");
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff