#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
+#include <linux/smp_lock.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
/*
* Version Information
*/
-#define DRIVER_VERSION "v1.4.3"
+#define DRIVER_VERSION "v1.5.0"
#define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com>, Bill Ryder <bryder@sgi.com>, Kuba Ober <kuba@mareimbrium.org>"
#define DRIVER_DESC "USB FTDI Serial Converters Driver"
struct delayed_work rx_work;
struct usb_serial_port *port;
int rx_processed;
- unsigned long rx_bytes;
- __u16 interface; /* FT2232C port interface (0 for FT232/245) */
+ __u16 interface; /* FT2232C, FT2232H or FT4232H port interface
+ (0 for FT232/245) */
speed_t force_baud; /* if non-zero, force the baud rate to
this value */
unsigned long tx_bytes;
unsigned long tx_outstanding_bytes;
unsigned long tx_outstanding_urbs;
+ unsigned short max_packet_size;
};
/* struct ftdi_sio_quirk is used by devices requiring special attention. */
static int ftdi_jtag_probe(struct usb_serial *serial);
static int ftdi_mtxorb_hack_setup(struct usb_serial *serial);
+static int ftdi_NDI_device_setup(struct usb_serial *serial);
static void ftdi_USB_UIRT_setup(struct ftdi_private *priv);
static void ftdi_HE_TIRA1_setup(struct ftdi_private *priv);
.probe = ftdi_mtxorb_hack_setup,
};
+static struct ftdi_sio_quirk ftdi_NDI_device_quirk = {
+ .probe = ftdi_NDI_device_setup,
+};
+
static struct ftdi_sio_quirk ftdi_USB_UIRT_quirk = {
.port_probe = ftdi_USB_UIRT_setup,
};
{ USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_232RL_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_8U2232C_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_4232H_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MICRO_CHAMELEON_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_RELAIS_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_OPENDCC_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_SNIFFER_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_THROTTLE_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GATEWAY_PID) },
{ USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_IOBOARD_PID) },
{ USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_MINI_IOBOARD_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SPROG_II) },
{ USB_DEVICE(FTDI_VID, FTDI_MTXORB_4_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MTXORB_5_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MTXORB_6_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_R2000KU_TRUE_RNG) },
{ USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0100_PID) },
{ USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0101_PID) },
{ USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0102_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CCSICDU20_0_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CCSICDU40_1_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CCSMACHX_2_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_CCSLOAD_N_GO_3_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_CCSICDU64_4_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_CCSPRIME8_5_PID) },
{ USB_DEVICE(FTDI_VID, INSIDE_ACCESSO) },
{ USB_DEVICE(INTREPID_VID, INTREPID_VALUECAN_PID) },
{ USB_DEVICE(INTREPID_VID, INTREPID_NEOVI_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_TACTRIX_OPENPORT_13S_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_TACTRIX_OPENPORT_13U_PID) },
{ USB_DEVICE(ELEKTOR_VID, ELEKTOR_FT323R_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_HUC_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_SPECTRA_SCU_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_FUTURE_2_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_FUTURE_3_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_NDI_AURORA_SCU_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
{ USB_DEVICE(TELLDUS_VID, TELLDUS_TELLSTICK_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_MAXSTREAM_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_PHI_FISCO_PID) },
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(FTDI_VID, LMI_LM3S_EVAL_BOARD_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(FTDI_VID, FTDI_TURTELIZER_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(RATOC_VENDOR_ID, RATOC_PRODUCT_ID_USB60F) },
{ USB_DEVICE(FTDI_VID, FTDI_REU_TINY_PID) },
{ USB_DEVICE(PAPOUCH_VID, PAPOUCH_QUIDO4x4_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_DOMINTELL_DUSB_PID) },
{ USB_DEVICE(ALTI2_VID, ALTI2_N3_PID) },
{ USB_DEVICE(FTDI_VID, DIEBOLD_BCS_SE923_PID) },
- { USB_DEVICE(FTDI_VID, FTDI_NDI_HUC_PID) },
{ USB_DEVICE(ATMEL_VID, STK541_PID) },
{ USB_DEVICE(DE_VID, STB_PID) },
{ USB_DEVICE(DE_VID, WHT_PID) },
{ USB_DEVICE(ADI_VID, ADI_GNICE_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(ADI_VID, ADI_GNICEPLUS_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(JETI_VID, JETI_SPC1201_PID) },
{ USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) },
+ { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) },
+ { USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) },
+ { USB_DEVICE(FTDI_VID, MARVELL_OPENRD_PID),
+ .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
+ { USB_DEVICE(FTDI_VID, HAMEG_HO820_PID) },
+ { USB_DEVICE(FTDI_VID, HAMEG_HO870_PID) },
{ }, /* Optional parameter entry */
{ } /* Terminating entry */
};
[FT232BM] = "FT232BM",
[FT2232C] = "FT2232C",
[FT232RL] = "FT232RL",
+ [FT2232H] = "FT2232H",
+ [FT4232H] = "FT4232H"
};
/* Constants for read urb and write urb */
#define BUFSZ 512
-#define PKTSZ 64
/* rx_flags */
#define THROTTLED 0x01
/* function prototypes for a FTDI serial converter */
static int ftdi_sio_probe(struct usb_serial *serial,
const struct usb_device_id *id);
-static void ftdi_shutdown(struct usb_serial *serial);
static int ftdi_sio_port_probe(struct usb_serial_port *port);
static int ftdi_sio_port_remove(struct usb_serial_port *port);
-static int ftdi_open(struct tty_struct *tty,
- struct usb_serial_port *port, struct file *filp);
+static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port);
static void ftdi_close(struct usb_serial_port *port);
static void ftdi_dtr_rts(struct usb_serial_port *port, int on);
static int ftdi_write(struct tty_struct *tty, struct usb_serial_port *port,
static unsigned short int ftdi_232am_baud_to_divisor(int baud);
static __u32 ftdi_232bm_baud_base_to_divisor(int baud, int base);
static __u32 ftdi_232bm_baud_to_divisor(int baud);
+static __u32 ftdi_2232h_baud_base_to_divisor(int baud, int base);
+static __u32 ftdi_2232h_baud_to_divisor(int baud);
static struct usb_serial_driver ftdi_sio_device = {
.driver = {
.ioctl = ftdi_ioctl,
.set_termios = ftdi_set_termios,
.break_ctl = ftdi_break_ctl,
- .shutdown = ftdi_shutdown,
};
return ftdi_232bm_baud_base_to_divisor(baud, 48000000);
}
+static __u32 ftdi_2232h_baud_base_to_divisor(int baud, int base)
+{
+ static const unsigned char divfrac[8] = { 0, 3, 2, 4, 1, 5, 6, 7 };
+ __u32 divisor;
+ int divisor3;
+
+ /* hi-speed baud rate is 10-bit sampling instead of 16-bit */
+ divisor3 = (base / 10 / baud) * 8;
+
+ divisor = divisor3 >> 3;
+ divisor |= (__u32)divfrac[divisor3 & 0x7] << 14;
+ /* Deal with special cases for highest baud rates. */
+ if (divisor == 1)
+ divisor = 0;
+ else if (divisor == 0x4001)
+ divisor = 1;
+ /*
+ * Set this bit to turn off a divide by 2.5 on baud rate generator
+ * This enables baud rates up to 12Mbaud but cannot reach below 1200
+ * baud with this bit set
+ */
+ divisor |= 0x00020000;
+ return divisor;
+}
+
+static __u32 ftdi_2232h_baud_to_divisor(int baud)
+{
+ return ftdi_2232h_baud_base_to_divisor(baud, 120000000);
+}
+
#define set_mctrl(port, set) update_mctrl((port), (set), 0)
#define clear_mctrl(port, clear) update_mctrl((port), 0, (clear))
case FT2232C: /* FT2232C chip */
case FT232RL:
if (baud <= 3000000) {
+ __u16 product_id = le16_to_cpu(
+ port->serial->dev->descriptor.idProduct);
+ if (((FTDI_NDI_HUC_PID == product_id) ||
+ (FTDI_NDI_SPECTRA_SCU_PID == product_id) ||
+ (FTDI_NDI_FUTURE_2_PID == product_id) ||
+ (FTDI_NDI_FUTURE_3_PID == product_id) ||
+ (FTDI_NDI_AURORA_SCU_PID == product_id)) &&
+ (baud == 19200)) {
+ baud = 1200000;
+ }
+ div_value = ftdi_232bm_baud_to_divisor(baud);
+ } else {
+ dbg("%s - Baud rate too high!", __func__);
+ div_value = ftdi_232bm_baud_to_divisor(9600);
+ div_okay = 0;
+ baud = 9600;
+ }
+ break;
+ case FT2232H: /* FT2232H chip */
+ case FT4232H: /* FT4232H chip */
+ if ((baud <= 12000000) & (baud >= 1200)) {
+ div_value = ftdi_2232h_baud_to_divisor(baud);
+ } else if (baud < 1200) {
div_value = ftdi_232bm_baud_to_divisor(baud);
} else {
dbg("%s - Baud rate too high!", __func__);
(new_serial.flags & ASYNC_FLAGS));
priv->custom_divisor = new_serial.custom_divisor;
- tty->low_latency = (priv->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
write_latency_timer(port);
check_and_exit:
if (interfaces > 1) {
int inter;
- /* Multiple interfaces. Assume FT2232C. */
- priv->chip_type = FT2232C;
+ /* Multiple interfaces.*/
+ if (version == 0x0800) {
+ priv->chip_type = FT4232H;
+ /* Hi-speed - baud clock runs at 120MHz */
+ priv->baud_base = 120000000 / 2;
+ } else if (version == 0x0700) {
+ priv->chip_type = FT2232H;
+ /* Hi-speed - baud clock runs at 120MHz */
+ priv->baud_base = 120000000 / 2;
+ } else
+ priv->chip_type = FT2232C;
+
/* Determine interface code. */
inter = serial->interface->altsetting->desc.bInterfaceNumber;
- if (inter == 0)
- priv->interface = PIT_SIOA;
- else
- priv->interface = PIT_SIOB;
+ if (inter == 0) {
+ priv->interface = INTERFACE_A;
+ } else if (inter == 1) {
+ priv->interface = INTERFACE_B;
+ } else if (inter == 2) {
+ priv->interface = INTERFACE_C;
+ } else if (inter == 3) {
+ priv->interface = INTERFACE_D;
+ }
/* BM-type devices have a bug where bcdDevice gets set
* to 0x200 when iSerialNumber is 0. */
if (version < 0x500) {
}
+/* Determine the maximum packet size for the device. This depends on the chip
+ * type and the USB host capabilities. The value should be obtained from the
+ * device descriptor as the chip will use the appropriate values for the host.*/
+static void ftdi_set_max_packet_size(struct usb_serial_port *port)
+{
+ struct ftdi_private *priv = usb_get_serial_port_data(port);
+ struct usb_serial *serial = port->serial;
+ struct usb_device *udev = serial->dev;
+
+ struct usb_interface *interface = serial->interface;
+ struct usb_endpoint_descriptor *ep_desc = &interface->cur_altsetting->endpoint[1].desc;
+
+ unsigned num_endpoints;
+ int i = 0;
+
+ num_endpoints = interface->cur_altsetting->desc.bNumEndpoints;
+ dev_info(&udev->dev, "Number of endpoints %d\n", num_endpoints);
+
+ /* NOTE: some customers have programmed FT232R/FT245R devices
+ * with an endpoint size of 0 - not good. In this case, we
+ * want to override the endpoint descriptor setting and use a
+ * value of 64 for wMaxPacketSize */
+ for (i = 0; i < num_endpoints; i++) {
+ dev_info(&udev->dev, "Endpoint %d MaxPacketSize %d\n", i+1,
+ interface->cur_altsetting->endpoint[i].desc.wMaxPacketSize);
+ ep_desc = &interface->cur_altsetting->endpoint[i].desc;
+ if (ep_desc->wMaxPacketSize == 0) {
+ ep_desc->wMaxPacketSize = cpu_to_le16(0x40);
+ dev_info(&udev->dev, "Overriding wMaxPacketSize on endpoint %d\n", i);
+ }
+ }
+
+ /* set max packet size based on descriptor */
+ priv->max_packet_size = ep_desc->wMaxPacketSize;
+
+ dev_info(&udev->dev, "Setting MaxPacketSize %d\n", priv->max_packet_size);
+}
+
+
/*
* ***************************************************************************
* Sysfs Attribute
if ((!retval) &&
(priv->chip_type == FT232BM ||
priv->chip_type == FT2232C ||
- priv->chip_type == FT232RL)) {
+ priv->chip_type == FT232RL ||
+ priv->chip_type == FT2232H ||
+ priv->chip_type == FT4232H)) {
retval = device_create_file(&port->dev,
&dev_attr_latency_timer);
}
device_remove_file(&port->dev, &dev_attr_event_char);
if (priv->chip_type == FT232BM ||
priv->chip_type == FT2232C ||
- priv->chip_type == FT232RL) {
+ priv->chip_type == FT232RL ||
+ priv->chip_type == FT2232H ||
+ priv->chip_type == FT4232H) {
device_remove_file(&port->dev, &dev_attr_latency_timer);
}
}
usb_set_serial_port_data(port, priv);
ftdi_determine_type(port);
+ ftdi_set_max_packet_size(port);
read_latency_timer(port);
create_sysfs_attrs(port);
return 0;
} /* ftdi_HE_TIRA1_setup */
/*
+ * Module parameter to control latency timer for NDI FTDI-based USB devices.
+ * If this value is not set in modprobe.conf.local its value will be set to 1ms.
+ */
+static int ndi_latency_timer = 1;
+
+/* Setup for the NDI FTDI-based USB devices, which requires hardwired
+ * baudrate (19200 gets mapped to 1200000).
+ *
+ * Called from usbserial:serial_probe.
+ */
+static int ftdi_NDI_device_setup(struct usb_serial *serial)
+{
+ struct usb_device *udev = serial->dev;
+ int latency = ndi_latency_timer;
+ int rv = 0;
+ char buf[1];
+
+ if (latency == 0)
+ latency = 1;
+ if (latency > 99)
+ latency = 99;
+
+ dbg("%s setting NDI device latency to %d", __func__, latency);
+ dev_info(&udev->dev, "NDI device with a latency value of %d", latency);
+
+ rv = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
+ FTDI_SIO_SET_LATENCY_TIMER_REQUEST,
+ FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE,
+ latency, 0, buf, 0, WDR_TIMEOUT);
+ return 0;
+}
+
+/*
* First port on JTAG adaptors such as Olimex arm-usb-ocd or the FIC/OpenMoko
* Neo1973 Debug Board is reserved for JTAG interface and can be accessed from
* userspace using openocd.
return 0;
}
-/* ftdi_shutdown is called from usbserial:usb_serial_disconnect
- * it is called when the usb device is disconnected
- *
- * usbserial:usb_serial_disconnect
- * calls __serial_close for each open of the port
- * shutdown is called then (ie ftdi_shutdown)
- */
-static void ftdi_shutdown(struct usb_serial *serial)
-{
- dbg("%s", __func__);
-}
-
static void ftdi_sio_priv_release(struct kref *k)
{
struct ftdi_private *priv = container_of(k, struct ftdi_private, kref);
return 0;
}
-static int ftdi_open(struct tty_struct *tty,
- struct usb_serial_port *port, struct file *filp)
+static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port)
{ /* ftdi_open */
struct usb_device *dev = port->serial->dev;
struct ftdi_private *priv = usb_get_serial_port_data(port);
spin_lock_irqsave(&priv->tx_lock, flags);
priv->tx_bytes = 0;
spin_unlock_irqrestore(&priv->tx_lock, flags);
- spin_lock_irqsave(&priv->rx_lock, flags);
- priv->rx_bytes = 0;
- spin_unlock_irqrestore(&priv->rx_lock, flags);
-
- if (tty)
- tty->low_latency = (priv->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
write_latency_timer(port);
if (data_offset > 0) {
/* Original sio needs control bytes too... */
transfer_size += (data_offset *
- ((count + (PKTSZ - 1 - data_offset)) /
- (PKTSZ - data_offset)));
+ ((count + (priv->max_packet_size - 1 - data_offset)) /
+ (priv->max_packet_size - data_offset)));
}
buffer = kmalloc(transfer_size, GFP_ATOMIC);
if (data_offset > 0) {
/* Original sio requires control byte at start of
each packet. */
- int user_pktsz = PKTSZ - data_offset;
+ int user_pktsz = priv->max_packet_size - data_offset;
int todo = count;
unsigned char *first_byte = buffer;
const unsigned char *current_position = buf;
dbg("%s - port %d", __func__, port->number);
- if (status) {
- dbg("nonzero write bulk status received: %d", status);
- return;
- }
-
priv = usb_get_serial_port_data(port);
if (!priv) {
dbg("%s - bad port private data pointer - exiting", __func__);
data_offset = priv->write_offset;
if (data_offset > 0) {
/* Subtract the control bytes */
- countback -= (data_offset * DIV_ROUND_UP(countback, PKTSZ));
+ countback -= (data_offset * DIV_ROUND_UP(countback, priv->max_packet_size));
}
spin_lock_irqsave(&priv->tx_lock, flags);
--priv->tx_outstanding_urbs;
priv->tx_outstanding_bytes -= countback;
spin_unlock_irqrestore(&priv->tx_lock, flags);
+ if (status) {
+ dbg("nonzero write bulk status received: %d", status);
+ return;
+ }
+
usb_serial_port_softint(port);
} /* ftdi_write_bulk_callback */
struct usb_serial_port *port = urb->context;
struct tty_struct *tty;
struct ftdi_private *priv;
- unsigned long countread;
- unsigned long flags;
int status = urb->status;
if (urb->number_of_packets > 0) {
goto out;
}
- /* count data bytes, but not status bytes */
- countread = urb->actual_length;
- countread -= 2 * DIV_ROUND_UP(countread, PKTSZ);
- spin_lock_irqsave(&priv->rx_lock, flags);
- priv->rx_bytes += countread;
- spin_unlock_irqrestore(&priv->rx_lock, flags);
-
ftdi_process_read(&priv->rx_work.work);
out:
tty_kref_put(tty);
need_flip = 0;
for (packet_offset = priv->rx_processed;
- packet_offset < urb->actual_length; packet_offset += PKTSZ) {
+ packet_offset < urb->actual_length; packet_offset += priv->max_packet_size) {
int length;
/* Compare new line status to the old one, signal if different/
priv->prev_status = new_status;
}
- length = min_t(u32, PKTSZ, urb->actual_length-packet_offset)-2;
+ length = min_t(u32, priv->max_packet_size, urb->actual_length-packet_offset)-2;
if (length < 0) {
dev_err(&port->dev, "%s - bad packet length: %d\n",
__func__, length+2);
if (data[packet_offset+1] & FTDI_RS_BI) {
error_flag = TTY_BREAK;
dbg("BREAK received");
+ usb_serial_handle_break(port);
}
if (data[packet_offset+1] & FTDI_RS_PE) {
error_flag = TTY_PARITY;
/* Note that the error flag is duplicated for
every character received since we don't know
which character it applied to */
- tty_insert_flip_char(tty,
- data[packet_offset + i], error_flag);
+ if (!usb_serial_handle_sysrq_char(tty, port,
+ data[packet_offset + i]))
+ tty_insert_flip_char(tty,
+ data[packet_offset + i],
+ error_flag);
}
need_flip = 1;
}
case FT232BM:
case FT2232C:
case FT232RL:
+ case FT2232H:
+ case FT4232H:
/* the 8U232AM returns a two byte value (the sio is a 1 byte
value) - in the same format as the data returned from the in
point */
module_param(product, ushort, 0);
MODULE_PARM_DESC(product, "User specified product ID");
+module_param(ndi_latency_timer, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(ndi_latency_timer, "NDI device latency timer override");