/*
* EHCI HCD (Host Controller Driver) for USB.
*
- * (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net>
- *
* Bus Glue for AMD Alchemy Au1xxx
*
* Based on "ohci-au1xxx.c" by Matt Porter <mporter@kernel.crashing.org>
#define USB_MCFG_RDCOMB (1<<30)
#define USB_MCFG_SSDEN (1<<23)
#define USB_MCFG_PHYPLLEN (1<<19)
+#define USB_MCFG_UCECLKEN (1<<18)
#define USB_MCFG_EHCCLKEN (1<<17)
+#ifdef CONFIG_DMA_COHERENT
#define USB_MCFG_UCAM (1<<7)
+#else
+#define USB_MCFG_UCAM (0)
+#endif
#define USB_MCFG_EBMEN (1<<3)
#define USB_MCFG_EMEMEN (1<<2)
-#define USBH_ENABLE_CE (USB_MCFG_PHYPLLEN | USB_MCFG_EHCCLKEN)
+#define USBH_ENABLE_CE (USB_MCFG_PHYPLLEN | USB_MCFG_EHCCLKEN)
+#define USBH_ENABLE_INIT (USB_MCFG_PFEN | USB_MCFG_RDCOMB | \
+ USBH_ENABLE_CE | USB_MCFG_SSDEN | \
+ USB_MCFG_UCAM | USB_MCFG_EBMEN | \
+ USB_MCFG_EMEMEN)
-#ifdef CONFIG_DMA_COHERENT
-#define USBH_ENABLE_INIT (USBH_ENABLE_CE \
- | USB_MCFG_PFEN | USB_MCFG_RDCOMB \
- | USB_MCFG_SSDEN | USB_MCFG_UCAM \
- | USB_MCFG_EBMEN | USB_MCFG_EMEMEN)
-#else
-#define USBH_ENABLE_INIT (USBH_ENABLE_CE \
- | USB_MCFG_PFEN | USB_MCFG_RDCOMB \
- | USB_MCFG_SSDEN \
- | USB_MCFG_EBMEN | USB_MCFG_EMEMEN)
-#endif
#define USBH_DISABLE (USB_MCFG_EBMEN | USB_MCFG_EMEMEN)
extern int usb_disabled(void);
-/*-------------------------------------------------------------------------*/
-
-static void au1xxx_start_ehc(struct platform_device *dev)
+static void au1xxx_start_ehc(void)
{
- pr_debug(__FILE__ ": starting Au1xxx EHCI USB Controller\n");
-
- /* write HW defaults again in case Yamon cleared them */
- if (au_readl(USB_HOST_CONFIG) == 0) {
- au_writel(0x00d02000, USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
- udelay(1000);
- }
- /* enable host controller */
- au_writel(USBH_ENABLE_CE | au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
- udelay(1000);
- au_writel(USBH_ENABLE_INIT | au_readl(USB_HOST_CONFIG),
- USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
+ /* enable clock to EHCI block and HS PHY PLL*/
+ au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_CE, USB_HOST_CONFIG);
+ au_sync();
udelay(1000);
- pr_debug(__FILE__ ": Clock to USB host has been enabled\n");
+ /* enable EHCI mmio */
+ au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG);
+ au_sync();
+ udelay(1000);
}
-static void au1xxx_stop_ehc(struct platform_device *dev)
+static void au1xxx_stop_ehc(void)
{
- pr_debug(__FILE__ ": stopping Au1xxx EHCI USB Controller\n");
+ unsigned long c;
/* Disable mem */
- au_writel(~USBH_DISABLE & au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG);
+ au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_DISABLE, USB_HOST_CONFIG);
+ au_sync();
udelay(1000);
- /* Disable clock */
- au_writel(~USB_MCFG_EHCCLKEN & au_readl(USB_HOST_CONFIG),
- USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
+
+ /* Disable EHC clock. If the HS PHY is unused disable it too. */
+ c = au_readl(USB_HOST_CONFIG) & ~USB_MCFG_EHCCLKEN;
+ if (!(c & USB_MCFG_UCECLKEN)) /* UDC disabled? */
+ c &= ~USB_MCFG_PHYPLLEN; /* yes: disable HS PHY PLL */
+ au_writel(c, USB_HOST_CONFIG);
+ au_sync();
}
-/*-------------------------------------------------------------------------*/
+static const struct hc_driver ehci_au1xxx_hc_driver = {
+ .description = hcd_name,
+ .product_desc = "Au1xxx EHCI",
+ .hcd_priv_size = sizeof(struct ehci_hcd),
-/* configure so an HC device and id are always provided */
-/* always called with process context; sleeping is OK */
+ /*
+ * generic hardware linkage
+ */
+ .irq = ehci_irq,
+ .flags = HCD_MEMORY | HCD_USB2,
-/**
- * usb_ehci_au1xxx_probe - initialize Au1xxx-based HCDs
- * Context: !in_interrupt()
- *
- * Allocates basic resources for this USB host controller, and
- * then invokes the start() method for the HCD associated with it
- * through the hotplug entry's driver_data.
- *
- */
-int usb_ehci_au1xxx_probe(const struct hc_driver *driver,
- struct usb_hcd **hcd_out, struct platform_device *dev)
+ /*
+ * basic lifecycle operations
+ *
+ * FIXME -- ehci_init() doesn't do enough here.
+ * See ehci-ppc-soc for a complete implementation.
+ */
+ .reset = ehci_init,
+ .start = ehci_run,
+ .stop = ehci_stop,
+ .shutdown = ehci_shutdown,
+
+ /*
+ * managing i/o requests and associated device resources
+ */
+ .urb_enqueue = ehci_urb_enqueue,
+ .urb_dequeue = ehci_urb_dequeue,
+ .endpoint_disable = ehci_endpoint_disable,
+
+ /*
+ * scheduling support
+ */
+ .get_frame_number = ehci_get_frame,
+
+ /*
+ * root hub support
+ */
+ .hub_status_data = ehci_hub_status_data,
+ .hub_control = ehci_hub_control,
+ .bus_suspend = ehci_bus_suspend,
+ .bus_resume = ehci_bus_resume,
+ .relinquish_port = ehci_relinquish_port,
+ .port_handed_over = ehci_port_handed_over,
+};
+
+static int ehci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
{
- int retval;
struct usb_hcd *hcd;
struct ehci_hcd *ehci;
+ int ret;
-#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT)
+ if (usb_disabled())
+ return -ENODEV;
+#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT)
/* Au1200 AB USB does not support coherent memory */
if (!(read_c0_prid() & 0xff)) {
- pr_info("%s: this is chip revision AB!\n", dev->name);
- pr_info("%s: update your board or re-configure the kernel\n",
- dev->name);
+ printk(KERN_INFO "%s: this is chip revision AB!\n", pdev->name);
+ printk(KERN_INFO "%s: update your board or re-configure"
+ " the kernel\n", pdev->name);
return -ENODEV;
}
#endif
- au1xxx_start_ehc(dev);
-
- if (dev->resource[1].flags != IORESOURCE_IRQ) {
+ if (pdev->resource[1].flags != IORESOURCE_IRQ) {
pr_debug("resource[1] is not IORESOURCE_IRQ");
- retval = -ENOMEM;
+ return -ENOMEM;
}
- hcd = usb_create_hcd(driver, &dev->dev, "Au1xxx");
+ hcd = usb_create_hcd(&ehci_au1xxx_hc_driver, &pdev->dev, "Au1xxx");
if (!hcd)
return -ENOMEM;
- hcd->rsrc_start = dev->resource[0].start;
- hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1;
+
+ hcd->rsrc_start = pdev->resource[0].start;
+ hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
pr_debug("request_mem_region failed");
- retval = -EBUSY;
+ ret = -EBUSY;
goto err1;
}
hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
if (!hcd->regs) {
pr_debug("ioremap failed");
- retval = -ENOMEM;
+ ret = -ENOMEM;
goto err2;
}
+ au1xxx_start_ehc();
+
ehci = hcd_to_ehci(hcd);
ehci->caps = hcd->regs;
ehci->regs = hcd->regs + HC_LENGTH(readl(&ehci->caps->hc_capbase));
/* cache this readonly data; minimize chip reads */
ehci->hcs_params = readl(&ehci->caps->hcs_params);
- /* ehci_hcd_init(hcd_to_ehci(hcd)); */
-
- retval =
- usb_add_hcd(hcd, dev->resource[1].start, IRQF_DISABLED | IRQF_SHARED);
- if (retval == 0)
- return retval;
+ ret = usb_add_hcd(hcd, pdev->resource[1].start,
+ IRQF_DISABLED | IRQF_SHARED);
+ if (ret == 0) {
+ platform_set_drvdata(pdev, hcd);
+ return ret;
+ }
- au1xxx_stop_ehc(dev);
+ au1xxx_stop_ehc();
iounmap(hcd->regs);
err2:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
err1:
usb_put_hcd(hcd);
- return retval;
+ return ret;
}
-/* may be called without controller electrically present */
-/* may be called with controller, bus, and devices active */
-
-/**
- * usb_ehci_hcd_au1xxx_remove - shutdown processing for Au1xxx-based HCDs
- * @dev: USB Host Controller being removed
- * Context: !in_interrupt()
- *
- * Reverses the effect of usb_ehci_hcd_au1xxx_probe(), first invoking
- * the HCD's stop() method. It is always called from a thread
- * context, normally "rmmod", "apmd", or something similar.
- *
- */
-void usb_ehci_au1xxx_remove(struct usb_hcd *hcd, struct platform_device *dev)
+static int ehci_hcd_au1xxx_drv_remove(struct platform_device *pdev)
{
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
usb_remove_hcd(hcd);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
- au1xxx_stop_ehc(dev);
-}
+ au1xxx_stop_ehc();
+ platform_set_drvdata(pdev, NULL);
-/*-------------------------------------------------------------------------*/
+ return 0;
+}
-static const struct hc_driver ehci_au1xxx_hc_driver = {
- .description = hcd_name,
- .product_desc = "Au1xxx EHCI",
- .hcd_priv_size = sizeof(struct ehci_hcd),
+#ifdef CONFIG_PM
+static int ehci_hcd_au1xxx_drv_suspend(struct platform_device *pdev,
+ pm_message_t message)
+{
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+ unsigned long flags;
+ int rc;
- /*
- * generic hardware linkage
+ return 0;
+ rc = 0;
+
+ if (time_before(jiffies, ehci->next_statechange))
+ msleep(10);
+
+ /* Root hub was already suspended. Disable irq emission and
+ * mark HW unaccessible, bail out if RH has been resumed. Use
+ * the spinlock to properly synchronize with possible pending
+ * RH suspend or resume activity.
+ *
+ * This is still racy as hcd->state is manipulated outside of
+ * any locks =P But that will be a different fix.
*/
- .irq = ehci_irq,
- .flags = HCD_MEMORY | HCD_USB2,
+ spin_lock_irqsave(&ehci->lock, flags);
+ if (hcd->state != HC_STATE_SUSPENDED) {
+ rc = -EINVAL;
+ goto bail;
+ }
+ ehci_writel(ehci, 0, &ehci->regs->intr_enable);
+ (void)ehci_readl(ehci, &ehci->regs->intr_enable);
- /*
- * basic lifecycle operations
- */
- .reset = ehci_init,
- .start = ehci_run,
- .stop = ehci_stop,
+ /* make sure snapshot being resumed re-enumerates everything */
+ if (message.event == PM_EVENT_PRETHAW) {
+ ehci_halt(ehci);
+ ehci_reset(ehci);
+ }
- /*
- * managing i/o requests and associated device resources
- */
- .urb_enqueue = ehci_urb_enqueue,
- .urb_dequeue = ehci_urb_dequeue,
- .endpoint_disable = ehci_endpoint_disable,
+ clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
- /*
- * scheduling support
- */
- .get_frame_number = ehci_get_frame,
+ au1xxx_stop_ehc();
- /*
- * root hub support
- */
- .hub_status_data = ehci_hub_status_data,
- .hub_control = ehci_hub_control,
-#ifdef CONFIG_PM
- .hub_suspend = ehci_hub_suspend,
- .hub_resume = ehci_hub_resume,
-#endif
-};
+bail:
+ spin_unlock_irqrestore(&ehci->lock, flags);
-/*-------------------------------------------------------------------------*/
+ // could save FLADJ in case of Vaux power loss
+ // ... we'd only use it to handle clock skew
-static int ehci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
+ return rc;
+}
+
+
+static int ehci_hcd_au1xxx_drv_resume(struct platform_device *pdev)
{
- struct usb_hcd *hcd = NULL;
- int ret;
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ struct ehci_hcd *ehci = hcd_to_ehci(hcd);
- pr_debug("In ehci_hcd_au1xxx_drv_probe\n");
+ au1xxx_start_ehc();
- if (usb_disabled())
- return -ENODEV;
+ // maybe restore FLADJ
- ret = usb_ehci_au1xxx_probe(&ehci_au1xxx_hc_driver, &hcd, pdev);
- return ret;
-}
+ if (time_before(jiffies, ehci->next_statechange))
+ msleep(100);
-static int ehci_hcd_au1xxx_drv_remove(struct platform_device *pdev)
-{
- struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ /* Mark hardware accessible again as we are out of D3 state by now */
+ set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
- usb_ehci_au1xxx_remove(hcd, pdev);
- return 0;
-}
+ /* If CF is still set, we maintained PCI Vaux power.
+ * Just undo the effect of ehci_pci_suspend().
+ */
+ if (ehci_readl(ehci, &ehci->regs->configured_flag) == FLAG_CF) {
+ int mask = INTR_MASK;
+
+ if (!hcd->self.root_hub->do_remote_wakeup)
+ mask &= ~STS_PCD;
+ ehci_writel(ehci, mask, &ehci->regs->intr_enable);
+ ehci_readl(ehci, &ehci->regs->intr_enable);
+ return 0;
+ }
- /*TBD*/
-/*static int ehci_hcd_au1xxx_drv_suspend(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct usb_hcd *hcd = dev_get_drvdata(dev);
+ ehci_dbg(ehci, "lost power, restarting\n");
+ usb_root_hub_lost_power(hcd->self.root_hub);
- return 0;
-}
-static int ehci_hcd_au1xxx_drv_resume(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct usb_hcd *hcd = dev_get_drvdata(dev);
+ /* Else reset, to cope with power loss or flush-to-storage
+ * style "resume" having let BIOS kick in during reboot.
+ */
+ (void) ehci_halt(ehci);
+ (void) ehci_reset(ehci);
+
+ /* emptying the schedule aborts any urbs */
+ spin_lock_irq(&ehci->lock);
+ if (ehci->reclaim)
+ end_unlink_async(ehci);
+ ehci_work(ehci);
+ spin_unlock_irq(&ehci->lock);
+
+ ehci_writel(ehci, ehci->command, &ehci->regs->command);
+ ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag);
+ ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */
+
+ /* here we "know" root ports should always stay powered */
+ ehci_port_power(ehci, 1);
+
+ hcd->state = HC_STATE_SUSPENDED;
return 0;
}
-*/
-MODULE_ALIAS("au1xxx-ehci");
+
+#else
+#define ehci_hcd_au1xxx_drv_suspend NULL
+#define ehci_hcd_au1xxx_drv_resume NULL
+#endif
+
static struct platform_driver ehci_hcd_au1xxx_driver = {
- .probe = ehci_hcd_au1xxx_drv_probe,
- .remove = ehci_hcd_au1xxx_drv_remove,
- /*.suspend = ehci_hcd_au1xxx_drv_suspend, */
- /*.resume = ehci_hcd_au1xxx_drv_resume, */
+ .probe = ehci_hcd_au1xxx_drv_probe,
+ .remove = ehci_hcd_au1xxx_drv_remove,
+ .shutdown = usb_hcd_platform_shutdown,
+ .suspend = ehci_hcd_au1xxx_drv_suspend,
+ .resume = ehci_hcd_au1xxx_drv_resume,
.driver = {
- .name = "au1xxx-ehci",
- .bus = &platform_bus_type
+ .name = "au1xxx-ehci",
+ .owner = THIS_MODULE,
}
};
+
+MODULE_ALIAS("platform:au1xxx-ehci");
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff