comment "USB Host Controller Drivers"
depends on USB
+config USB_C67X00_HCD
+ tristate "Cypress C67x00 HCD support"
+ depends on USB
+ help
+ The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
+ host/peripheral/OTG USB controllers.
+
+ Enable this option to support this chip in host controller mode.
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called c67x00.
+
config USB_EHCI_HCD
tristate "EHCI HCD (USB 2.0) support"
depends on USB && USB_ARCH_HAS_EHCI
To compile this driver as a module, choose M here: the
module will be called ehci-hcd.
-config USB_EHCI_SPLIT_ISO
- bool "Full speed ISO transactions (EXPERIMENTAL)"
- depends on USB_EHCI_HCD && EXPERIMENTAL
- default n
- ---help---
- This code is new and hasn't been used with many different
- EHCI or USB 2.0 transaction translator implementations.
- It should work for ISO-OUT transfers, like audio.
-
config USB_EHCI_ROOT_HUB_TT
- bool "Root Hub Transaction Translators (EXPERIMENTAL)"
- depends on USB_EHCI_HCD && EXPERIMENTAL
+ bool "Root Hub Transaction Translators"
+ depends on USB_EHCI_HCD
---help---
Some EHCI chips have vendor-specific extensions to integrate
transaction translators, so that no OHCI or UHCI companion
If unsure, say N.
+config USB_EHCI_BIG_ENDIAN_MMIO
+ bool
+ depends on USB_EHCI_HCD && (PPC_CELLEB || PPC_PS3 || 440EPX || ARCH_IXP4XX)
+ default y
+
+config USB_EHCI_BIG_ENDIAN_DESC
+ bool
+ depends on USB_EHCI_HCD && (440EPX || ARCH_IXP4XX)
+ default y
+
+config USB_EHCI_FSL
+ bool "Support for Freescale on-chip EHCI USB controller"
+ depends on USB_EHCI_HCD && FSL_SOC
+ select USB_EHCI_ROOT_HUB_TT
+ ---help---
+ Variation of ARC USB block used in some Freescale chips.
+
+config USB_EHCI_HCD_PPC_OF
+ bool "EHCI support for PPC USB controller on OF platform bus"
+ depends on USB_EHCI_HCD && PPC_OF
+ default y
+ ---help---
+ Enables support for the USB controller present on the PowerPC
+ OpenFirmware platform bus.
+
+config USB_OXU210HP_HCD
+ tristate "OXU210HP HCD support"
+ depends on USB
+ ---help---
+ The OXU210HP is an USB host/OTG/device controller. Enable this
+ option if your board has this chip. If unsure, say N.
+
+ This driver does not support isochronous transfers and doesn't
+ implement OTG nor USB device controllers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called oxu210hp-hcd.
+
config USB_ISP116X_HCD
tristate "ISP116X HCD support"
depends on USB
To compile this driver as a module, choose M here: the
module will be called isp116x-hcd.
+config USB_ISP1760_HCD
+ tristate "ISP 1760 HCD support"
+ depends on USB && EXPERIMENTAL && (PCI || PPC_OF)
+ ---help---
+ The ISP1760 chip is a USB 2.0 host controller.
+
+ This driver does not support isochronous transfers or OTG.
+ This USB controller is usually attached to a non-DMA-Master
+ capable bus. NXP's eval kit brings this chip on PCI card
+ where the chip itself is behind a PLB to simulate such
+ a bus.
+
+ To compile this driver as a module, choose M here: the
+ module will be called isp1760.
+
config USB_OHCI_HCD
tristate "OHCI HCD support"
depends on USB && USB_ARCH_HAS_OHCI
select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
+ select USB_OTG_UTILS if ARCH_OMAP
---help---
The Open Host Controller Interface (OHCI) is a standard for accessing
USB 1.1 host controller hardware. It does more in hardware than Intel's
bool "OHCI support for on-chip PPC USB controller"
depends on USB_OHCI_HCD && (STB03xxx || PPC_MPC52xx)
default y
- select USB_OHCI_BIG_ENDIAN
+ select USB_OHCI_BIG_ENDIAN_DESC
+ select USB_OHCI_BIG_ENDIAN_MMIO
---help---
Enables support for the USB controller on the MPC52xx or
STB03xxx processor chip. If unsure, say Y.
+config USB_OHCI_HCD_PPC_OF
+ bool "OHCI support for PPC USB controller on OF platform bus"
+ depends on USB_OHCI_HCD && PPC_OF
+ default y
+ ---help---
+ Enables support for the USB controller PowerPC present on the
+ OpenFirmware platform bus.
+
+config USB_OHCI_HCD_PPC_OF_BE
+ bool "Support big endian HC"
+ depends on USB_OHCI_HCD_PPC_OF
+ default y
+ select USB_OHCI_BIG_ENDIAN_DESC
+ select USB_OHCI_BIG_ENDIAN_MMIO
+
+config USB_OHCI_HCD_PPC_OF_LE
+ bool "Support little endian HC"
+ depends on USB_OHCI_HCD_PPC_OF
+ default n
+ select USB_OHCI_LITTLE_ENDIAN
+
config USB_OHCI_HCD_PCI
bool "OHCI support for PCI-bus USB controllers"
- depends on USB_OHCI_HCD && PCI && (STB03xxx || PPC_MPC52xx)
+ depends on USB_OHCI_HCD && PCI && (STB03xxx || PPC_MPC52xx || USB_OHCI_HCD_PPC_OF)
default y
select USB_OHCI_LITTLE_ENDIAN
---help---
Enables support for PCI-bus plug-in USB controller cards.
If unsure, say Y.
-config USB_OHCI_BIG_ENDIAN
+config USB_OHCI_HCD_SSB
+ bool "OHCI support for Broadcom SSB OHCI core"
+ depends on USB_OHCI_HCD && (SSB = y || SSB = USB_OHCI_HCD) && EXPERIMENTAL
+ default n
+ ---help---
+ Support for the Sonics Silicon Backplane (SSB) attached
+ Broadcom USB OHCI core.
+
+ This device is present in some embedded devices with
+ Broadcom based SSB bus.
+
+ If unsure, say N.
+
+config USB_OHCI_BIG_ENDIAN_DESC
+ bool
+ depends on USB_OHCI_HCD
+ default n
+
+config USB_OHCI_BIG_ENDIAN_MMIO
bool
depends on USB_OHCI_HCD
default n
To compile this driver as a module, choose M here: the
module will be called uhci-hcd.
+config USB_FHCI_HCD
+ tristate "Freescale QE USB Host Controller support"
+ depends on USB && OF_GPIO && QE_GPIO && QUICC_ENGINE
+ select FSL_GTM
+ select QE_USB
+ help
+ This driver enables support for Freescale QE USB Host Controller
+ (as found on MPC8360 and MPC8323 processors), the driver supports
+ Full and Low Speed USB.
+
+config FHCI_DEBUG
+ bool "Freescale QE USB Host Controller debug support"
+ depends on USB_FHCI_HCD && DEBUG_FS
+ help
+ Say "y" to see some FHCI debug information and statistics
+ throught debugfs.
+
+config USB_U132_HCD
+ tristate "Elan U132 Adapter Host Controller"
+ depends on USB && USB_FTDI_ELAN
+ default M
+ help
+ The U132 adapter is a USB to CardBus adapter specifically designed
+ for PC cards that contain an OHCI host controller. Typical PC cards
+ are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
+ adapter will *NOT* work with PC cards that do not contain an OHCI
+ controller.
+
+ For those PC cards that contain multiple OHCI controllers only the
+ first one is used.
+
+ The driver consists of two modules, the "ftdi-elan" module is a
+ USB client driver that interfaces to the FTDI chip within ELAN's
+ USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
+ controller driver that talks to the OHCI controller within the
+ CardBus cards that are inserted in the U132 adapter.
+
+ This driver has been tested with a CardBus OHCI USB adapter, and
+ worked with a USB PEN Drive inserted into the first USB port of
+ the PCCARD. A rather pointless thing to do, but useful for testing.
+
+ It is safe to say M here.
+
+ See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
+
config USB_SL811_HCD
tristate "SL811HS HCD support"
depends on USB
To compile this driver as a module, choose M here: the
module will be called "sl811_cs".
+config USB_R8A66597_HCD
+ tristate "R8A66597 HCD support"
+ depends on USB
+ help
+ The R8A66597 is a USB 2.0 host and peripheral controller.
+
+ Enable this option if your board has this chip, and you want
+ to use it as a host controller. If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called r8a66597-hcd.
+
+config SUPERH_ON_CHIP_R8A66597
+ boolean "Enable SuperH on-chip R8A66597 USB"
+ depends on USB_R8A66597_HCD && (CPU_SUBTYPE_SH7366 || CPU_SUBTYPE_SH7723)
+ help
+ This driver enables support for the on-chip R8A66597 in the
+ SH7366 and SH7723 processors.
+
+config USB_WHCI_HCD
+ tristate "Wireless USB Host Controller Interface (WHCI) driver (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ depends on PCI && USB
+ select USB_WUSB
+ select UWB_WHCI
+ help
+ A driver for PCI-based Wireless USB Host Controllers that are
+ compliant with the WHCI specification.
+
+ To compile this driver a module, choose M here: the module
+ will be called "whci-hcd".
+
+config USB_HWA_HCD
+ tristate "Host Wire Adapter (HWA) driver (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ depends on USB
+ select USB_WUSB
+ select UWB_HWA
+ help
+ This driver enables you to connect Wireless USB devices to
+ your system using a Host Wire Adaptor USB dongle. This is an
+ UWB Radio Controller and WUSB Host Controller connected to
+ your machine via USB (specified in WUSB1.0).
+
+ To compile this driver a module, choose M here: the module
+ will be called "hwa-hc".
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff