Enables support for the USB controller present on the PowerPC
OpenFirmware platform bus.
+config USB_OXU210HP_HCD
+ tristate "OXU210HP HCD support"
+ depends on USB
+ ---help---
+ The OXU210HP is an USB host/OTG/device controller. Enable this
+ option if your board has this chip. If unsure, say N.
+
+ This driver does not support isochronous transfers and doesn't
+ implement OTG nor USB device controllers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called oxu210hp-hcd.
+
config USB_ISP116X_HCD
tristate "ISP116X HCD support"
depends on USB
config USB_ISP1760_HCD
tristate "ISP 1760 HCD support"
- depends on USB && EXPERIMENTAL
+ depends on USB && EXPERIMENTAL && (PCI || PPC_OF)
---help---
The ISP1760 chip is a USB 2.0 host controller.
This driver does not support isochronous transfers or OTG.
+ This USB controller is usually attached to a non-DMA-Master
+ capable bus. NXP's eval kit brings this chip on PCI card
+ where the chip itself is behind a PLB to simulate such
+ a bus.
To compile this driver as a module, choose M here: the
- module will be called isp1760-hcd.
-
-config USB_ISP1760_PCI
- bool "Support for the PCI bus"
- depends on USB_ISP1760_HCD && PCI
- ---help---
- Enables support for the device present on the PCI bus.
- This should only be required if you happen to have the eval kit from
- NXP and you are going to test it.
-
-config USB_ISP1760_OF
- bool "Support for the OF platform bus"
- depends on USB_ISP1760_HCD && PPC_OF
- ---help---
- Enables support for the device present on the PowerPC
- OpenFirmware platform bus.
+ module will be called isp1760.
config USB_OHCI_HCD
tristate "OHCI HCD support"
depends on USB && USB_ARCH_HAS_OHCI
select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
- select I2C if ARCH_PNX4008
+ select USB_OTG_UTILS if ARCH_OMAP
---help---
The Open Host Controller Interface (OHCI) is a standard for accessing
USB 1.1 host controller hardware. It does more in hardware than Intel's
To compile this driver as a module, choose M here: the
module will be called uhci-hcd.
+config USB_FHCI_HCD
+ tristate "Freescale QE USB Host Controller support"
+ depends on USB && OF_GPIO && QE_GPIO && QUICC_ENGINE
+ select FSL_GTM
+ select QE_USB
+ help
+ This driver enables support for Freescale QE USB Host Controller
+ (as found on MPC8360 and MPC8323 processors), the driver supports
+ Full and Low Speed USB.
+
+config FHCI_DEBUG
+ bool "Freescale QE USB Host Controller debug support"
+ depends on USB_FHCI_HCD && DEBUG_FS
+ help
+ Say "y" to see some FHCI debug information and statistics
+ throught debugfs.
+
config USB_U132_HCD
tristate "Elan U132 Adapter Host Controller"
depends on USB && USB_FTDI_ELAN
SH7366 and SH7723 processors.
config USB_WHCI_HCD
- tristate "Wireless USB Host Controller Interface (WHCI) driver"
+ tristate "Wireless USB Host Controller Interface (WHCI) driver (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
depends on PCI && USB
select USB_WUSB
select UWB_WHCI
will be called "whci-hcd".
config USB_HWA_HCD
- tristate "Host Wire Adapter (HWA) driver"
+ tristate "Host Wire Adapter (HWA) driver (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
depends on USB
select USB_WUSB
select UWB_HWA