+/*
+ * Standalone EHCI usb debug driver
+ *
+ * Originally written by:
+ * Eric W. Biederman" <ebiederm@xmission.com> and
+ * Yinghai Lu <yhlu.kernel@gmail.com>
+ *
+ * Changes for early/late printk and HW errata:
+ * Jason Wessel <jason.wessel@windriver.com>
+ * Copyright (C) 2009 Wind River Systems, Inc.
+ *
+ */
+
#include <linux/console.h>
#include <linux/errno.h>
+#include <linux/module.h>
#include <linux/pci_regs.h>
#include <linux/pci_ids.h>
#include <linux/usb/ch9.h>
#include <asm/pci-direct.h>
#include <asm/fixmap.h>
+/* The code here is intended to talk directly to the EHCI debug port
+ * and does not require that you have any kind of USB host controller
+ * drivers or USB device drivers compiled into the kernel.
+ *
+ * If you make a change to anything in here, the following test cases
+ * need to pass where a USB debug device works in the following
+ * configurations.
+ *
+ * 1. boot args: earlyprintk=dbgp
+ * o kernel compiled with # CONFIG_USB_EHCI_HCD is not set
+ * o kernel compiled with CONFIG_USB_EHCI_HCD=y
+ * 2. boot args: earlyprintk=dbgp,keep
+ * o kernel compiled with # CONFIG_USB_EHCI_HCD is not set
+ * o kernel compiled with CONFIG_USB_EHCI_HCD=y
+ * 3. boot args: earlyprintk=dbgp console=ttyUSB0
+ * o kernel has CONFIG_USB_EHCI_HCD=y and
+ * CONFIG_USB_SERIAL_DEBUG=y
+ * 4. boot args: earlyprintk=vga,dbgp
+ * o kernel compiled with # CONFIG_USB_EHCI_HCD is not set
+ * o kernel compiled with CONFIG_USB_EHCI_HCD=y
+ *
+ * For the 4th configuration you can turn on or off the DBGP_DEBUG
+ * such that you can debug the dbgp device's driver code.
+ */
+
+static int dbgp_phys_port = 1;
+
static struct ehci_caps __iomem *ehci_caps;
static struct ehci_regs __iomem *ehci_regs;
static struct ehci_dbg_port __iomem *ehci_debug;
+static int dbgp_not_safe; /* Cannot use debug device during ehci reset */
static unsigned int dbgp_endpoint_out;
struct ehci_dev {
#define USB_DEBUG_DEVNUM 127
-#define DBGP_DATA_TOGGLE 0x8800
-
-static inline u32 dbgp_pid_update(u32 x, u32 tok)
+#ifdef DBGP_DEBUG
+#define dbgp_printk printk
+static void dbgp_ehci_status(char *str)
{
- return ((x ^ DBGP_DATA_TOGGLE) & 0xffff00) | (tok & 0xff);
+ if (!ehci_debug)
+ return;
+ dbgp_printk("dbgp: %s\n", str);
+ dbgp_printk(" Debug control: %08x", readl(&ehci_debug->control));
+ dbgp_printk(" ehci cmd : %08x", readl(&ehci_regs->command));
+ dbgp_printk(" ehci conf flg: %08x\n",
+ readl(&ehci_regs->configured_flag));
+ dbgp_printk(" ehci status : %08x", readl(&ehci_regs->status));
+ dbgp_printk(" ehci portsc : %08x\n",
+ readl(&ehci_regs->port_status[dbgp_phys_port - 1]));
}
+#else
+static inline void dbgp_ehci_status(char *str) { }
+static inline void dbgp_printk(const char *fmt, ...) { }
+#endif
static inline u32 dbgp_len_update(u32 x, u32 len)
{
#define HUB_RESET_TIMEOUT 500
#define DBGP_MAX_PACKET 8
+#define DBGP_TIMEOUT (250 * 1000)
+#define DBGP_LOOPS 1000
+
+static inline u32 dbgp_pid_write_update(u32 x, u32 tok)
+{
+ static int data0 = USB_PID_DATA1;
+ data0 ^= USB_PID_DATA_TOGGLE;
+ return (x & 0xffff0000) | (data0 << 8) | (tok & 0xff);
+}
+
+static inline u32 dbgp_pid_read_update(u32 x, u32 tok)
+{
+ return (x & 0xffff0000) | (USB_PID_DATA0 << 8) | (tok & 0xff);
+}
static int dbgp_wait_until_complete(void)
{
u32 ctrl;
- int loop = 0x100000;
+ int loop = DBGP_TIMEOUT;
do {
ctrl = readl(&ehci_debug->control);
/* Stop when the transaction is finished */
if (ctrl & DBGP_DONE)
break;
+ udelay(1);
} while (--loop > 0);
if (!loop)
- return -1;
+ return -DBGP_TIMEOUT;
/*
* Now that we have observed the completed transaction,
return (ctrl & DBGP_ERROR) ? -DBGP_ERRCODE(ctrl) : DBGP_LEN(ctrl);
}
-static void __init dbgp_mdelay(int ms)
+static inline void dbgp_mdelay(int ms)
{
int i;
{
u32 pids, lpid;
int ret;
- int loop = 3;
+ int loop = DBGP_LOOPS;
retry:
writel(ctrl | DBGP_GO, &ehci_debug->control);
pids = readl(&ehci_debug->pids);
lpid = DBGP_PID_GET(pids);
- if (ret < 0)
+ if (ret < 0) {
+ /* A -DBGP_TIMEOUT failure here means the device has
+ * failed, perhaps because it was unplugged, in which
+ * case we do not want to hang the system so the dbgp
+ * will be marked as unsafe to use. EHCI reset is the
+ * only way to recover if you unplug the dbgp device.
+ */
+ if (ret == -DBGP_TIMEOUT && !dbgp_not_safe)
+ dbgp_not_safe = 1;
+ if (ret == -DBGP_ERR_BAD && --loop > 0)
+ goto retry;
return ret;
+ }
/*
* If the port is getting full or it has dropped data
return ret;
}
-static void dbgp_set_data(const void *buf, int size)
+static inline void dbgp_set_data(const void *buf, int size)
{
const unsigned char *bytes = buf;
u32 lo, hi;
writel(hi, &ehci_debug->data47);
}
-static void __init dbgp_get_data(void *buf, int size)
+static inline void dbgp_get_data(void *buf, int size)
{
unsigned char *bytes = buf;
u32 lo, hi;
static int dbgp_bulk_write(unsigned devnum, unsigned endpoint,
const char *bytes, int size)
{
- u32 pids, addr, ctrl;
int ret;
+ u32 addr;
+ u32 pids, ctrl;
if (size > DBGP_MAX_PACKET)
return -1;
addr = DBGP_EPADDR(devnum, endpoint);
pids = readl(&ehci_debug->pids);
- pids = dbgp_pid_update(pids, USB_PID_OUT);
+ pids = dbgp_pid_write_update(pids, USB_PID_OUT);
ctrl = readl(&ehci_debug->control);
ctrl = dbgp_len_update(ctrl, size);
dbgp_set_data(bytes, size);
writel(addr, &ehci_debug->address);
writel(pids, &ehci_debug->pids);
-
ret = dbgp_wait_until_done(ctrl);
- if (ret < 0)
- return ret;
return ret;
}
-static int __init dbgp_bulk_read(unsigned devnum, unsigned endpoint, void *data,
+static int dbgp_bulk_read(unsigned devnum, unsigned endpoint, void *data,
int size)
{
u32 pids, addr, ctrl;
addr = DBGP_EPADDR(devnum, endpoint);
pids = readl(&ehci_debug->pids);
- pids = dbgp_pid_update(pids, USB_PID_IN);
+ pids = dbgp_pid_read_update(pids, USB_PID_IN);
ctrl = readl(&ehci_debug->control);
ctrl = dbgp_len_update(ctrl, size);
return ret;
}
-static int __init dbgp_control_msg(unsigned devnum, int requesttype,
+static int dbgp_control_msg(unsigned devnum, int requesttype,
int request, int value, int index, void *data, int size)
{
u32 pids, addr, ctrl;
return dbgp_bulk_read(devnum, 0, data, size);
}
-
/* Find a PCI capability */
static u32 __init find_cap(u32 num, u32 slot, u32 func, int cap)
{
return 0;
}
-static int __init ehci_reset_port(int port)
+static int dbgp_ehci_startup(void)
+{
+ u32 ctrl, cmd, status;
+ int loop;
+
+ /* Claim ownership, but do not enable yet */
+ ctrl = readl(&ehci_debug->control);
+ ctrl |= DBGP_OWNER;
+ ctrl &= ~(DBGP_ENABLED | DBGP_INUSE);
+ writel(ctrl, &ehci_debug->control);
+ udelay(1);
+
+ dbgp_ehci_status("EHCI startup");
+ /* Start the ehci running */
+ cmd = readl(&ehci_regs->command);
+ cmd &= ~(CMD_LRESET | CMD_IAAD | CMD_PSE | CMD_ASE | CMD_RESET);
+ cmd |= CMD_RUN;
+ writel(cmd, &ehci_regs->command);
+
+ /* Ensure everything is routed to the EHCI */
+ writel(FLAG_CF, &ehci_regs->configured_flag);
+
+ /* Wait until the controller is no longer halted */
+ loop = 10;
+ do {
+ status = readl(&ehci_regs->status);
+ if (!(status & STS_HALT))
+ break;
+ udelay(1);
+ } while (--loop > 0);
+
+ if (!loop) {
+ dbgp_printk("ehci can not be started\n");
+ return -ENODEV;
+ }
+ dbgp_printk("ehci started\n");
+ return 0;
+}
+
+static int dbgp_ehci_controller_reset(void)
+{
+ int loop = 250 * 1000;
+ u32 cmd;
+
+ /* Reset the EHCI controller */
+ cmd = readl(&ehci_regs->command);
+ cmd |= CMD_RESET;
+ writel(cmd, &ehci_regs->command);
+ do {
+ cmd = readl(&ehci_regs->command);
+ } while ((cmd & CMD_RESET) && (--loop > 0));
+
+ if (!loop) {
+ dbgp_printk("can not reset ehci\n");
+ return -1;
+ }
+ dbgp_ehci_status("ehci reset done");
+ return 0;
+}
+static int ehci_wait_for_port(int port);
+/* Return 0 on success
+ * Return -ENODEV for any general failure
+ * Return -EIO if wait for port fails
+ */
+int dbgp_external_startup(void)
+{
+ int devnum;
+ struct usb_debug_descriptor dbgp_desc;
+ int ret;
+ u32 ctrl, portsc, cmd;
+ int dbg_port = dbgp_phys_port;
+ int tries = 3;
+ int reset_port_tries = 1;
+ int try_hard_once = 1;
+
+try_port_reset_again:
+ ret = dbgp_ehci_startup();
+ if (ret)
+ return ret;
+
+ /* Wait for a device to show up in the debug port */
+ ret = ehci_wait_for_port(dbg_port);
+ if (ret < 0) {
+ portsc = readl(&ehci_regs->port_status[dbg_port - 1]);
+ if (!(portsc & PORT_CONNECT) && try_hard_once) {
+ /* Last ditch effort to try to force enable
+ * the debug device by using the packet test
+ * ehci command to try and wake it up. */
+ try_hard_once = 0;
+ cmd = readl(&ehci_regs->command);
+ cmd &= ~CMD_RUN;
+ writel(cmd, &ehci_regs->command);
+ portsc = readl(&ehci_regs->port_status[dbg_port - 1]);
+ portsc |= PORT_TEST_PKT;
+ writel(portsc, &ehci_regs->port_status[dbg_port - 1]);
+ dbgp_ehci_status("Trying to force debug port online");
+ mdelay(50);
+ dbgp_ehci_controller_reset();
+ goto try_port_reset_again;
+ } else if (reset_port_tries--) {
+ goto try_port_reset_again;
+ }
+ dbgp_printk("No device found in debug port\n");
+ return -EIO;
+ }
+ dbgp_ehci_status("wait for port done");
+
+ /* Enable the debug port */
+ ctrl = readl(&ehci_debug->control);
+ ctrl |= DBGP_CLAIM;
+ writel(ctrl, &ehci_debug->control);
+ ctrl = readl(&ehci_debug->control);
+ if ((ctrl & DBGP_CLAIM) != DBGP_CLAIM) {
+ dbgp_printk("No device in debug port\n");
+ writel(ctrl & ~DBGP_CLAIM, &ehci_debug->control);
+ return -ENODEV;
+ }
+ dbgp_ehci_status("debug ported enabled");
+
+ /* Completely transfer the debug device to the debug controller */
+ portsc = readl(&ehci_regs->port_status[dbg_port - 1]);
+ portsc &= ~PORT_PE;
+ writel(portsc, &ehci_regs->port_status[dbg_port - 1]);
+
+ dbgp_mdelay(100);
+
+try_again:
+ /* Find the debug device and make it device number 127 */
+ for (devnum = 0; devnum <= 127; devnum++) {
+ ret = dbgp_control_msg(devnum,
+ USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
+ USB_REQ_GET_DESCRIPTOR, (USB_DT_DEBUG << 8), 0,
+ &dbgp_desc, sizeof(dbgp_desc));
+ if (ret > 0)
+ break;
+ }
+ if (devnum > 127) {
+ dbgp_printk("Could not find attached debug device\n");
+ goto err;
+ }
+ if (ret < 0) {
+ dbgp_printk("Attached device is not a debug device\n");
+ goto err;
+ }
+ dbgp_endpoint_out = dbgp_desc.bDebugOutEndpoint;
+
+ /* Move the device to 127 if it isn't already there */
+ if (devnum != USB_DEBUG_DEVNUM) {
+ ret = dbgp_control_msg(devnum,
+ USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
+ USB_REQ_SET_ADDRESS, USB_DEBUG_DEVNUM, 0, NULL, 0);
+ if (ret < 0) {
+ dbgp_printk("Could not move attached device to %d\n",
+ USB_DEBUG_DEVNUM);
+ goto err;
+ }
+ devnum = USB_DEBUG_DEVNUM;
+ dbgp_printk("debug device renamed to 127\n");
+ }
+
+ /* Enable the debug interface */
+ ret = dbgp_control_msg(USB_DEBUG_DEVNUM,
+ USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
+ USB_REQ_SET_FEATURE, USB_DEVICE_DEBUG_MODE, 0, NULL, 0);
+ if (ret < 0) {
+ dbgp_printk(" Could not enable the debug device\n");
+ goto err;
+ }
+ dbgp_printk("debug interface enabled\n");
+ /* Perform a small write to get the even/odd data state in sync
+ */
+ ret = dbgp_bulk_write(USB_DEBUG_DEVNUM, dbgp_endpoint_out, " ", 1);
+ if (ret < 0) {
+ dbgp_printk("dbgp_bulk_write failed: %d\n", ret);
+ goto err;
+ }
+ dbgp_printk("small write doned\n");
+ dbgp_not_safe = 0;
+
+ return 0;
+err:
+ if (tries--)
+ goto try_again;
+ return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(dbgp_external_startup);
+
+static int ehci_reset_port(int port)
{
u32 portsc;
u32 delay_time, delay;
int loop;
+ dbgp_ehci_status("reset port");
/* Reset the usb debug port */
portsc = readl(&ehci_regs->port_status[port - 1]);
portsc &= ~PORT_PE;
for (delay_time = 0; delay_time < HUB_RESET_TIMEOUT;
delay_time += delay) {
dbgp_mdelay(delay);
-
portsc = readl(&ehci_regs->port_status[port - 1]);
+ if (!(portsc & PORT_RESET))
+ break;
+ }
if (portsc & PORT_RESET) {
/* force reset to complete */
- loop = 2;
+ loop = 100 * 1000;
writel(portsc & ~(PORT_RWC_BITS | PORT_RESET),
&ehci_regs->port_status[port - 1]);
do {
+ udelay(1);
portsc = readl(&ehci_regs->port_status[port-1]);
} while ((portsc & PORT_RESET) && (--loop > 0));
}
/* If we've finished resetting, then break out of the loop */
if (!(portsc & PORT_RESET) && (portsc & PORT_PE))
return 0;
- }
return -EBUSY;
}
-static int __init ehci_wait_for_port(int port)
+static int ehci_wait_for_port(int port)
{
u32 status;
int ret, reps;
- for (reps = 0; reps < 3; reps++) {
- dbgp_mdelay(100);
+ for (reps = 0; reps < 300; reps++) {
status = readl(&ehci_regs->status);
- if (status & STS_PCD) {
- ret = ehci_reset_port(port);
- if (ret == 0)
- return 0;
- }
+ if (status & STS_PCD)
+ break;
+ dbgp_mdelay(1);
}
+ ret = ehci_reset_port(port);
+ if (ret == 0)
+ return 0;
return -ENOTCONN;
}
-#ifdef DBGP_DEBUG
-# define dbgp_printk early_printk
-#else
-static inline void dbgp_printk(const char *fmt, ...) { }
-#endif
-
typedef void (*set_debug_port_t)(int port);
static void __init default_set_debug_port(int port)
}
}
+/* The code in early_ehci_bios_handoff() is derived from the usb pci
+ * quirk initialization, but altered so as to use the early PCI
+ * routines. */
+#define EHCI_USBLEGSUP_BIOS (1 << 16) /* BIOS semaphore */
+#define EHCI_USBLEGCTLSTS 4 /* legacy control/status */
+static void __init early_ehci_bios_handoff(void)
+{
+ u32 hcc_params = readl(&ehci_caps->hcc_params);
+ int offset = (hcc_params >> 8) & 0xff;
+ u32 cap;
+ int msec;
+
+ if (!offset)
+ return;
+
+ cap = read_pci_config(ehci_dev.bus, ehci_dev.slot,
+ ehci_dev.func, offset);
+ dbgp_printk("dbgp: ehci BIOS state %08x\n", cap);
+
+ if ((cap & 0xff) == 1 && (cap & EHCI_USBLEGSUP_BIOS)) {
+ dbgp_printk("dbgp: BIOS handoff\n");
+ write_pci_config_byte(ehci_dev.bus, ehci_dev.slot,
+ ehci_dev.func, offset + 3, 1);
+ }
+
+ /* if boot firmware now owns EHCI, spin till it hands it over. */
+ msec = 1000;
+ while ((cap & EHCI_USBLEGSUP_BIOS) && (msec > 0)) {
+ mdelay(10);
+ msec -= 10;
+ cap = read_pci_config(ehci_dev.bus, ehci_dev.slot,
+ ehci_dev.func, offset);
+ }
+
+ if (cap & EHCI_USBLEGSUP_BIOS) {
+ /* well, possibly buggy BIOS... try to shut it down,
+ * and hope nothing goes too wrong */
+ dbgp_printk("dbgp: BIOS handoff failed: %08x\n", cap);
+ write_pci_config_byte(ehci_dev.bus, ehci_dev.slot,
+ ehci_dev.func, offset + 2, 0);
+ }
+
+ /* just in case, always disable EHCI SMIs */
+ write_pci_config_byte(ehci_dev.bus, ehci_dev.slot, ehci_dev.func,
+ offset + EHCI_USBLEGCTLSTS, 0);
+}
+
static int __init ehci_setup(void)
{
- struct usb_debug_descriptor dbgp_desc;
- u32 cmd, ctrl, status, portsc, hcs_params;
+ u32 ctrl, portsc, hcs_params;
u32 debug_port, new_debug_port = 0, n_ports;
- u32 devnum;
int ret, i;
- int loop;
int port_map_tried;
int playtimes = 3;
+ early_ehci_bios_handoff();
+
try_next_time:
port_map_tried = 0;
hcs_params = readl(&ehci_caps->hcs_params);
debug_port = HCS_DEBUG_PORT(hcs_params);
+ dbgp_phys_port = debug_port;
n_ports = HCS_N_PORTS(hcs_params);
dbgp_printk("debug_port: %d\n", debug_port);
dbgp_printk("n_ports: %d\n", n_ports);
+ dbgp_ehci_status("");
for (i = 1; i <= n_ports; i++) {
portsc = readl(&ehci_regs->port_status[i-1]);
return -1;
}
- loop = 100000;
- /* Reset the EHCI controller */
- cmd = readl(&ehci_regs->command);
- cmd |= CMD_RESET;
- writel(cmd, &ehci_regs->command);
- do {
- cmd = readl(&ehci_regs->command);
- } while ((cmd & CMD_RESET) && (--loop > 0));
-
- if (!loop) {
- dbgp_printk("can not reset ehci\n");
- return -1;
- }
- dbgp_printk("ehci reset done\n");
-
- /* Claim ownership, but do not enable yet */
- ctrl = readl(&ehci_debug->control);
- ctrl |= DBGP_OWNER;
- ctrl &= ~(DBGP_ENABLED | DBGP_INUSE);
- writel(ctrl, &ehci_debug->control);
-
- /* Start the ehci running */
- cmd = readl(&ehci_regs->command);
- cmd &= ~(CMD_LRESET | CMD_IAAD | CMD_PSE | CMD_ASE | CMD_RESET);
- cmd |= CMD_RUN;
- writel(cmd, &ehci_regs->command);
-
- /* Ensure everything is routed to the EHCI */
- writel(FLAG_CF, &ehci_regs->configured_flag);
-
- /* Wait until the controller is no longer halted */
- loop = 10;
- do {
- status = readl(&ehci_regs->status);
- } while ((status & STS_HALT) && (--loop > 0));
-
- if (!loop) {
- dbgp_printk("ehci can be started\n");
- return -1;
+ /* Only reset the controller if it is not already in the
+ * configured state */
+ if (!(readl(&ehci_regs->configured_flag) & FLAG_CF)) {
+ if (dbgp_ehci_controller_reset() != 0)
+ return -1;
+ } else {
+ dbgp_ehci_status("ehci skip - already configured");
}
- dbgp_printk("ehci started\n");
- /* Wait for a device to show up in the debug port */
- ret = ehci_wait_for_port(debug_port);
- if (ret < 0) {
- dbgp_printk("No device found in debug port\n");
+ ret = dbgp_external_startup();
+ if (ret == -EIO)
goto next_debug_port;
- }
- dbgp_printk("ehci wait for port done\n");
-
- /* Enable the debug port */
- ctrl = readl(&ehci_debug->control);
- ctrl |= DBGP_CLAIM;
- writel(ctrl, &ehci_debug->control);
- ctrl = readl(&ehci_debug->control);
- if ((ctrl & DBGP_CLAIM) != DBGP_CLAIM) {
- dbgp_printk("No device in debug port\n");
- writel(ctrl & ~DBGP_CLAIM, &ehci_debug->control);
- goto err;
- }
- dbgp_printk("debug ported enabled\n");
-
- /* Completely transfer the debug device to the debug controller */
- portsc = readl(&ehci_regs->port_status[debug_port - 1]);
- portsc &= ~PORT_PE;
- writel(portsc, &ehci_regs->port_status[debug_port - 1]);
- dbgp_mdelay(100);
-
- /* Find the debug device and make it device number 127 */
- for (devnum = 0; devnum <= 127; devnum++) {
- ret = dbgp_control_msg(devnum,
- USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
- USB_REQ_GET_DESCRIPTOR, (USB_DT_DEBUG << 8), 0,
- &dbgp_desc, sizeof(dbgp_desc));
- if (ret > 0)
- break;
- }
- if (devnum > 127) {
- dbgp_printk("Could not find attached debug device\n");
- goto err;
- }
- if (ret < 0) {
- dbgp_printk("Attached device is not a debug device\n");
- goto err;
- }
- dbgp_endpoint_out = dbgp_desc.bDebugOutEndpoint;
-
- /* Move the device to 127 if it isn't already there */
- if (devnum != USB_DEBUG_DEVNUM) {
- ret = dbgp_control_msg(devnum,
- USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
- USB_REQ_SET_ADDRESS, USB_DEBUG_DEVNUM, 0, NULL, 0);
- if (ret < 0) {
- dbgp_printk("Could not move attached device to %d\n",
- USB_DEBUG_DEVNUM);
- goto err;
- }
- devnum = USB_DEBUG_DEVNUM;
- dbgp_printk("debug device renamed to 127\n");
- }
-
- /* Enable the debug interface */
- ret = dbgp_control_msg(USB_DEBUG_DEVNUM,
- USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
- USB_REQ_SET_FEATURE, USB_DEVICE_DEBUG_MODE, 0, NULL, 0);
if (ret < 0) {
- dbgp_printk(" Could not enable the debug device\n");
- goto err;
- }
- dbgp_printk("debug interface enabled\n");
-
- /* Perform a small write to get the even/odd data state in sync
- */
- ret = dbgp_bulk_write(USB_DEBUG_DEVNUM, dbgp_endpoint_out, " ", 1);
- if (ret < 0) {
- dbgp_printk("dbgp_bulk_write failed: %d\n", ret);
- goto err;
+ /* Things didn't work so remove my claim */
+ ctrl = readl(&ehci_debug->control);
+ ctrl &= ~(DBGP_CLAIM | DBGP_OUT);
+ writel(ctrl, &ehci_debug->control);
+ return -1;
}
- dbgp_printk("small write doned\n");
-
return 0;
-err:
- /* Things didn't work so remove my claim */
- ctrl = readl(&ehci_debug->control);
- ctrl &= ~(DBGP_CLAIM | DBGP_OUT);
- writel(ctrl, &ehci_debug->control);
- return -1;
next_debug_port:
port_map_tried |= (1<<(debug_port - 1));
return -1;
}
+ dbgp_ehci_status("early_init_complete");
return 0;
}
static void early_dbgp_write(struct console *con, const char *str, u32 n)
{
int chunk, ret;
+ char buf[DBGP_MAX_PACKET];
+ int use_cr = 0;
+ u32 cmd, ctrl;
+ int reset_run = 0;
- if (!ehci_debug)
+ if (!ehci_debug || dbgp_not_safe)
return;
+
+ cmd = readl(&ehci_regs->command);
+ if (unlikely(!(cmd & CMD_RUN))) {
+ /* If the ehci controller is not in the run state do extended
+ * checks to see if the acpi or some other initialization also
+ * reset the ehci debug port */
+ ctrl = readl(&ehci_debug->control);
+ if (!(ctrl & DBGP_ENABLED)) {
+ dbgp_not_safe = 1;
+ dbgp_external_startup();
+ } else {
+ cmd |= CMD_RUN;
+ writel(cmd, &ehci_regs->command);
+ reset_run = 1;
+ }
+ }
while (n > 0) {
- chunk = n;
- if (chunk > DBGP_MAX_PACKET)
- chunk = DBGP_MAX_PACKET;
- ret = dbgp_bulk_write(USB_DEBUG_DEVNUM,
- dbgp_endpoint_out, str, chunk);
- str += chunk;
- n -= chunk;
+ for (chunk = 0; chunk < DBGP_MAX_PACKET && n > 0;
+ str++, chunk++, n--) {
+ if (!use_cr && *str == '\n') {
+ use_cr = 1;
+ buf[chunk] = '\r';
+ str--;
+ n++;
+ continue;
+ }
+ if (use_cr)
+ use_cr = 0;
+ buf[chunk] = *str;
+ }
+ if (chunk > 0) {
+ ret = dbgp_bulk_write(USB_DEBUG_DEVNUM,
+ dbgp_endpoint_out, buf, chunk);
+ }
+ }
+ if (unlikely(reset_run)) {
+ cmd = readl(&ehci_regs->command);
+ cmd &= ~CMD_RUN;
+ writel(cmd, &ehci_regs->command);
}
}
.index = -1,
};
+int dbgp_reset_prep(void)
+{
+ u32 ctrl;
+
+ dbgp_not_safe = 1;
+ if (!ehci_debug)
+ return 0;
+
+ if (early_dbgp_console.index != -1 &&
+ !(early_dbgp_console.flags & CON_BOOT))
+ return 1;
+ /* This means the console is not initialized, or should get
+ * shutdown so as to allow for reuse of the usb device, which
+ * means it is time to shutdown the usb debug port. */
+ ctrl = readl(&ehci_debug->control);
+ if (ctrl & DBGP_ENABLED) {
+ ctrl &= ~(DBGP_CLAIM);
+ writel(ctrl, &ehci_debug->control);
+ }
+ return 0;
+}
+EXPORT_SYMBOL_GPL(dbgp_reset_prep);