# nobody's needed a slave side API yet. The master-role API is not
# fully appropriate there, so it'd need some thought to do well.
#
-menu "SPI support"
-
-config SPI
+menuconfig SPI
bool "SPI support"
+ depends on HAS_IOMEM
help
The "Serial Peripheral Interface" is a low level synchronous
protocol. Chips that support SPI can have data transfer rates
controller and a chipselect. Most SPI slaves don't support
dynamic device discovery; some are even write-only or read-only.
- SPI is widely used by microcontollers to talk with sensors,
+ SPI is widely used by microcontrollers to talk with sensors,
eeprom and flash memory, codecs and various other controller
chips, analog to digital (and d-to-a) converters, and more.
MMC and SD cards can be accessed using SPI protocol; and for
(half duplex), SSP, SSI, and PSP. This driver framework should
work with most such devices and controllers.
+if SPI
+
config SPI_DEBUG
boolean "Debug support for SPI drivers"
- depends on SPI && DEBUG_KERNEL
+ depends on DEBUG_KERNEL
help
Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
sysfs, and debugfs support in SPI controller and protocol drivers.
controller and the protocol drivers for the SPI slave chips
that are connected.
+if SPI_MASTER
+
comment "SPI Master Controller Drivers"
- depends on SPI_MASTER
+
+config SPI_ATMEL
+ tristate "Atmel SPI Controller"
+ depends on (ARCH_AT91 || AVR32)
+ help
+ This selects a driver for the Atmel SPI Controller, present on
+ many AT32 (AVR32) and AT91 (ARM) chips.
+
+config SPI_BFIN
+ tristate "SPI controller driver for ADI Blackfin5xx"
+ depends on BLACKFIN
+ help
+ This is the SPI controller master driver for Blackfin 5xx processor.
+
+config SPI_AU1550
+ tristate "Au1550/Au12x0 SPI Controller"
+ depends on (SOC_AU1550 || SOC_AU1200) && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ If you say yes to this option, support will be included for the
+ Au1550 SPI controller (may also work with Au1200,Au1210,Au1250).
+
+ This driver can also be built as a module. If so, the module
+ will be called au1550_spi.
config SPI_BITBANG
- tristate "Bitbanging SPI master"
- depends on SPI_MASTER && EXPERIMENTAL
+ tristate "Utilities for Bitbanging SPI masters"
help
With a few GPIO pins, your system can bitbang the SPI protocol.
Select this to get SPI support through I/O pins (GPIO, parallel
config SPI_BUTTERFLY
tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
- depends on SPI_MASTER && PARPORT && EXPERIMENTAL
+ depends on PARPORT
select SPI_BITBANG
help
This uses a custom parallel port cable to connect to an AVR
inexpensive battery powered microcontroller evaluation board.
This same cable can be used to flash new firmware.
+config SPI_GPIO
+ tristate "GPIO-based bitbanging SPI Master"
+ depends on GENERIC_GPIO
+ select SPI_BITBANG
+ help
+ This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
+ interface to manage MOSI, MISO, SCK, and chipselect signals. SPI
+ slaves connected to a bus using this driver are configured as usual,
+ except that the spi_board_info.controller_data holds the GPIO number
+ for the chipselect used by this controller driver.
+
+ Note that this driver often won't achieve even 1 Mbit/sec speeds,
+ making it unusually slow for SPI. If your platform can inline
+ GPIO operations, you should be able to leverage that for better
+ speed with a custom version of this driver; see the source code.
+
+config SPI_IMX
+ tristate "Freescale i.MX SPI controllers"
+ depends on ARCH_MXC
+ select SPI_BITBANG
+ help
+ This enables using the Freescale i.MX SPI controllers in master
+ mode.
+
+config SPI_LM70_LLP
+ tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
+ depends on PARPORT && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ This driver supports the NS LM70 LLP Evaluation Board,
+ which interfaces to an LM70 temperature sensor using
+ a parallel port.
+
+config SPI_MPC52xx_PSC
+ tristate "Freescale MPC52xx PSC SPI controller"
+ depends on PPC_MPC52xx && EXPERIMENTAL
+ help
+ This enables using the Freescale MPC52xx Programmable Serial
+ Controller in master SPI mode.
+
+config SPI_MPC8xxx
+ tristate "Freescale MPC8xxx SPI controller"
+ depends on FSL_SOC
+ help
+ This enables using the Freescale MPC8xxx SPI controllers in master
+ mode.
+
+ This driver uses a simple set of shift registers for data (opposed
+ to the CPM based descriptor model).
+
+config SPI_OMAP_UWIRE
+ tristate "OMAP1 MicroWire"
+ depends on ARCH_OMAP1
+ select SPI_BITBANG
+ help
+ This hooks up to the MicroWire controller on OMAP1 chips.
+
+config SPI_OMAP24XX
+ tristate "McSPI driver for OMAP24xx/OMAP34xx"
+ depends on ARCH_OMAP24XX || ARCH_OMAP34XX
+ help
+ SPI master controller for OMAP24xx/OMAP34xx Multichannel SPI
+ (McSPI) modules.
+
+config SPI_ORION
+ tristate "Orion SPI master (EXPERIMENTAL)"
+ depends on PLAT_ORION && EXPERIMENTAL
+ help
+ This enables using the SPI master controller on the Orion chips.
+
+config SPI_PL022
+ tristate "ARM AMBA PL022 SSP controller (EXPERIMENTAL)"
+ depends on ARM_AMBA && EXPERIMENTAL
+ default y if MACH_U300
+ default y if ARCH_REALVIEW
+ default y if INTEGRATOR_IMPD1
+ default y if ARCH_VERSATILE
+ help
+ This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
+ controller. If you have an embedded system with an AMBA(R)
+ bus and a PL022 controller, say Y or M here.
+
+config SPI_PPC4xx
+ tristate "PPC4xx SPI Controller"
+ depends on PPC32 && 4xx && SPI_MASTER
+ select SPI_BITBANG
+ help
+ This selects a driver for the PPC4xx SPI Controller.
+
config SPI_PXA2XX
tristate "PXA2xx SSP SPI master"
- depends on SPI_MASTER && ARCH_PXA && EXPERIMENTAL
+ depends on ARCH_PXA && EXPERIMENTAL
+ select PXA_SSP
help
This enables using a PXA2xx SSP port as a SPI master controller.
The driver can be configured to use any SSP port and additional
documentation can be found a Documentation/spi/pxa2xx.
+config SPI_S3C24XX
+ tristate "Samsung S3C24XX series SPI"
+ depends on ARCH_S3C2410 && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ SPI driver for Samsung S3C24XX series ARM SoCs
+
+config SPI_S3C24XX_GPIO
+ tristate "Samsung S3C24XX series SPI by GPIO"
+ depends on ARCH_S3C2410 && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ SPI driver for Samsung S3C24XX series ARM SoCs using
+ GPIO lines to provide the SPI bus. This can be used where
+ the inbuilt hardware cannot provide the transfer mode, or
+ where the board is using non hardware connected pins.
+
+config SPI_SH_SCI
+ tristate "SuperH SCI SPI controller"
+ depends on SUPERH
+ select SPI_BITBANG
+ help
+ SPI driver for SuperH SCI blocks.
+
+config SPI_STMP3XXX
+ tristate "Freescale STMP37xx/378x SPI/SSP controller"
+ depends on ARCH_STMP3XXX && SPI_MASTER
+ help
+ SPI driver for Freescale STMP37xx/378x SoC SSP interface
+
+config SPI_TXX9
+ tristate "Toshiba TXx9 SPI controller"
+ depends on GENERIC_GPIO && CPU_TX49XX
+ help
+ SPI driver for Toshiba TXx9 MIPS SoCs
+
+config SPI_XILINX
+ tristate "Xilinx SPI controller"
+ depends on (XILINX_VIRTEX || MICROBLAZE) && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ This exposes the SPI controller IP from the Xilinx EDK.
+
+ See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
+ Product Specification document (DS464) for hardware details.
+
#
# Add new SPI master controllers in alphabetical order above this line
#
-
#
# There are lots of SPI device types, with sensors and memory
# being probably the most widely used ones.
#
comment "SPI Protocol Masters"
- depends on SPI_MASTER
+config SPI_SPIDEV
+ tristate "User mode SPI device driver support"
+ depends on EXPERIMENTAL
+ help
+ This supports user mode SPI protocol drivers.
+
+ Note that this application programming interface is EXPERIMENTAL
+ and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
+
+config SPI_TLE62X0
+ tristate "Infineon TLE62X0 (for power switching)"
+ depends on SYSFS
+ help
+ SPI driver for Infineon TLE62X0 series line driver chips,
+ such as the TLE6220, TLE6230 and TLE6240. This provides a
+ sysfs interface, with each line presented as a kind of GPIO
+ exposing both switch control and diagnostic feedback.
#
# Add new SPI protocol masters in alphabetical order above this line
#
+endif # SPI_MASTER
# (slave support would go here)
-endmenu # "SPI support"
-
+endif # SPI