* Maintainer: Kumar Gala (galak@kernel.crashing.org) (CPM2)
* Pantelis Antoniou (panto@intracom.gr) (CPM1)
*
- * Copyright (C) 2004 Freescale Semiconductor, Inc.
+ * Copyright (C) 2004, 2007 Freescale Semiconductor, Inc.
* (C) 2004 Intracom, S.A.
* (C) 2005-2006 MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
+ * Vitaly Bordug <vbordug@ru.mvista.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#include <linux/bootmem.h>
#include <linux/dma-mapping.h>
#include <linux/fs_uart_pd.h>
+#include <linux/of_platform.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+#include <linux/clk.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/delay.h>
#include <asm/fs_pd.h>
+#include <asm/udbg.h>
#if defined(CONFIG_SERIAL_CPM_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#include "cpm_uart.h"
-/***********************************************************************/
-
-/* Track which ports are configured as uarts */
-int cpm_uart_port_map[UART_NR];
-/* How many ports did we config as uarts */
-int cpm_uart_nr = 0;
/**************************************************************/
/**************************************************************/
-
-/* Place-holder for board-specific stuff */
-struct platform_device* __attribute__ ((weak)) __init
-early_uart_get_pdev(int index)
-{
- return NULL;
-}
-
-
-static void cpm_uart_count(void)
-{
- cpm_uart_nr = 0;
-#ifdef CONFIG_SERIAL_CPM_SMC1
- cpm_uart_port_map[cpm_uart_nr++] = UART_SMC1;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SMC2
- cpm_uart_port_map[cpm_uart_nr++] = UART_SMC2;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SCC1
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC1;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SCC2
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC2;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SCC3
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC3;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SCC4
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC4;
-#endif
-}
-
-/* Get UART number by its id */
-static int cpm_uart_id2nr(int id)
-{
- int i;
- if (id < UART_NR) {
- for (i=0; i<UART_NR; i++) {
- if (cpm_uart_port_map[i] == id)
- return i;
- }
- }
-
- /* not found or invalid argument */
- return -1;
-}
-
/*
* Check, if transmit buffers are processed
*/
static unsigned int cpm_uart_tx_empty(struct uart_port *port)
{
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- volatile cbd_t *bdp = pinfo->tx_bd_base;
+ cbd_t __iomem *bdp = pinfo->tx_bd_base;
int ret = 0;
while (1) {
- if (bdp->cbd_sc & BD_SC_READY)
+ if (in_be16(&bdp->cbd_sc) & BD_SC_READY)
break;
- if (bdp->cbd_sc & BD_SC_WRAP) {
+ if (in_be16(&bdp->cbd_sc) & BD_SC_WRAP) {
ret = TIOCSER_TEMT;
break;
}
static void cpm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
- /* Whee. Do nothing. */
+ struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
+
+ if (pinfo->gpios[GPIO_RTS] >= 0)
+ gpio_set_value(pinfo->gpios[GPIO_RTS], !(mctrl & TIOCM_RTS));
+
+ if (pinfo->gpios[GPIO_DTR] >= 0)
+ gpio_set_value(pinfo->gpios[GPIO_DTR], !(mctrl & TIOCM_DTR));
}
static unsigned int cpm_uart_get_mctrl(struct uart_port *port)
{
- /* Whee. Do nothing. */
- return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
+ struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
+ unsigned int mctrl = TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+ if (pinfo->gpios[GPIO_CTS] >= 0) {
+ if (gpio_get_value(pinfo->gpios[GPIO_CTS]))
+ mctrl &= ~TIOCM_CTS;
+ }
+
+ if (pinfo->gpios[GPIO_DSR] >= 0) {
+ if (gpio_get_value(pinfo->gpios[GPIO_DSR]))
+ mctrl &= ~TIOCM_DSR;
+ }
+
+ if (pinfo->gpios[GPIO_DCD] >= 0) {
+ if (gpio_get_value(pinfo->gpios[GPIO_DCD]))
+ mctrl &= ~TIOCM_CAR;
+ }
+
+ if (pinfo->gpios[GPIO_RI] >= 0) {
+ if (!gpio_get_value(pinfo->gpios[GPIO_RI]))
+ mctrl |= TIOCM_RNG;
+ }
+
+ return mctrl;
}
/*
static void cpm_uart_stop_tx(struct uart_port *port)
{
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- volatile smc_t *smcp = pinfo->smcp;
- volatile scc_t *sccp = pinfo->sccp;
+ smc_t __iomem *smcp = pinfo->smcp;
+ scc_t __iomem *sccp = pinfo->sccp;
pr_debug("CPM uart[%d]:stop tx\n", port->line);
if (IS_SMC(pinfo))
- smcp->smc_smcm &= ~SMCM_TX;
+ clrbits8(&smcp->smc_smcm, SMCM_TX);
else
- sccp->scc_sccm &= ~UART_SCCM_TX;
+ clrbits16(&sccp->scc_sccm, UART_SCCM_TX);
}
/*
static void cpm_uart_start_tx(struct uart_port *port)
{
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- volatile smc_t *smcp = pinfo->smcp;
- volatile scc_t *sccp = pinfo->sccp;
+ smc_t __iomem *smcp = pinfo->smcp;
+ scc_t __iomem *sccp = pinfo->sccp;
pr_debug("CPM uart[%d]:start tx\n", port->line);
if (IS_SMC(pinfo)) {
- if (smcp->smc_smcm & SMCM_TX)
+ if (in_8(&smcp->smc_smcm) & SMCM_TX)
return;
} else {
- if (sccp->scc_sccm & UART_SCCM_TX)
+ if (in_be16(&sccp->scc_sccm) & UART_SCCM_TX)
return;
}
if (cpm_uart_tx_pump(port) != 0) {
if (IS_SMC(pinfo)) {
- smcp->smc_smcm |= SMCM_TX;
+ setbits8(&smcp->smc_smcm, SMCM_TX);
} else {
- sccp->scc_sccm |= UART_SCCM_TX;
+ setbits16(&sccp->scc_sccm, UART_SCCM_TX);
}
}
}
static void cpm_uart_stop_rx(struct uart_port *port)
{
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- volatile smc_t *smcp = pinfo->smcp;
- volatile scc_t *sccp = pinfo->sccp;
+ smc_t __iomem *smcp = pinfo->smcp;
+ scc_t __iomem *sccp = pinfo->sccp;
pr_debug("CPM uart[%d]:stop rx\n", port->line);
if (IS_SMC(pinfo))
- smcp->smc_smcm &= ~SMCM_RX;
+ clrbits8(&smcp->smc_smcm, SMCM_RX);
else
- sccp->scc_sccm &= ~UART_SCCM_RX;
+ clrbits16(&sccp->scc_sccm, UART_SCCM_RX);
}
/*
static void cpm_uart_break_ctl(struct uart_port *port, int break_state)
{
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- int line = pinfo - cpm_uart_ports;
pr_debug("CPM uart[%d]:break ctrl, break_state: %d\n", port->line,
break_state);
if (break_state)
- cpm_line_cr_cmd(line, CPM_CR_STOP_TX);
+ cpm_line_cr_cmd(pinfo, CPM_CR_STOP_TX);
else
- cpm_line_cr_cmd(line, CPM_CR_RESTART_TX);
+ cpm_line_cr_cmd(pinfo, CPM_CR_RESTART_TX);
}
/*
cpm_uart_tx_pump(port);
}
+#ifdef CONFIG_CONSOLE_POLL
+static int serial_polled;
+#endif
+
/*
* Receive characters
*/
static void cpm_uart_int_rx(struct uart_port *port)
{
int i;
- unsigned char ch, *cp;
- struct tty_struct *tty = port->info->tty;
+ unsigned char ch;
+ u8 *cp;
+ struct tty_struct *tty = port->info->port.tty;
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- volatile cbd_t *bdp;
+ cbd_t __iomem *bdp;
u16 status;
unsigned int flg;
*/
bdp = pinfo->rx_cur;
for (;;) {
+#ifdef CONFIG_CONSOLE_POLL
+ if (unlikely(serial_polled)) {
+ serial_polled = 0;
+ return;
+ }
+#endif
/* get status */
- status = bdp->cbd_sc;
+ status = in_be16(&bdp->cbd_sc);
/* If this one is empty, return happy */
if (status & BD_SC_EMPTY)
break;
/* get number of characters, and check spce in flip-buffer */
- i = bdp->cbd_datlen;
+ i = in_be16(&bdp->cbd_datlen);
/* If we have not enough room in tty flip buffer, then we try
* later, which will be the next rx-interrupt or a timeout
}
/* get pointer */
- cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo);
+ cp = cpm2cpu_addr(in_be32(&bdp->cbd_bufaddr), pinfo);
/* loop through the buffer */
while (i-- > 0) {
goto handle_error;
if (uart_handle_sysrq_char(port, ch))
continue;
-
+#ifdef CONFIG_CONSOLE_POLL
+ if (unlikely(serial_polled)) {
+ serial_polled = 0;
+ return;
+ }
+#endif
error_return:
tty_insert_flip_char(tty, ch, flg);
} /* End while (i--) */
/* This BD is ready to be used again. Clear status. get next */
- bdp->cbd_sc &= ~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV | BD_SC_ID);
- bdp->cbd_sc |= BD_SC_EMPTY;
+ clrbits16(&bdp->cbd_sc, BD_SC_BR | BD_SC_FR | BD_SC_PR |
+ BD_SC_OV | BD_SC_ID);
+ setbits16(&bdp->cbd_sc, BD_SC_EMPTY);
- if (bdp->cbd_sc & BD_SC_WRAP)
+ if (in_be16(&bdp->cbd_sc) & BD_SC_WRAP)
bdp = pinfo->rx_bd_base;
else
bdp++;
} /* End for (;;) */
/* Write back buffer pointer */
- pinfo->rx_cur = (volatile cbd_t *) bdp;
+ pinfo->rx_cur = bdp;
/* activate BH processing */
tty_flip_buffer_push(tty);
static irqreturn_t cpm_uart_int(int irq, void *data)
{
u8 events;
- struct uart_port *port = (struct uart_port *)data;
+ struct uart_port *port = data;
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- volatile smc_t *smcp = pinfo->smcp;
- volatile scc_t *sccp = pinfo->sccp;
+ smc_t __iomem *smcp = pinfo->smcp;
+ scc_t __iomem *sccp = pinfo->sccp;
pr_debug("CPM uart[%d]:IRQ\n", port->line);
if (IS_SMC(pinfo)) {
- events = smcp->smc_smce;
- smcp->smc_smce = events;
+ events = in_8(&smcp->smc_smce);
+ out_8(&smcp->smc_smce, events);
if (events & SMCM_BRKE)
uart_handle_break(port);
if (events & SMCM_RX)
if (events & SMCM_TX)
cpm_uart_int_tx(port);
} else {
- events = sccp->scc_scce;
- sccp->scc_scce = events;
+ events = in_be16(&sccp->scc_scce);
+ out_be16(&sccp->scc_scce, events);
if (events & UART_SCCM_BRKE)
uart_handle_break(port);
if (events & UART_SCCM_RX)
{
int retval;
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- int line = pinfo - cpm_uart_ports;
pr_debug("CPM uart[%d]:startup\n", port->line);
/* Startup rx-int */
if (IS_SMC(pinfo)) {
- pinfo->smcp->smc_smcm |= SMCM_RX;
- pinfo->smcp->smc_smcmr |= (SMCMR_REN | SMCMR_TEN);
+ setbits8(&pinfo->smcp->smc_smcm, SMCM_RX);
+ setbits16(&pinfo->smcp->smc_smcmr, (SMCMR_REN | SMCMR_TEN));
} else {
- pinfo->sccp->scc_sccm |= UART_SCCM_RX;
- pinfo->sccp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+ setbits16(&pinfo->sccp->scc_sccm, UART_SCCM_RX);
+ setbits32(&pinfo->sccp->scc_gsmrl, (SCC_GSMRL_ENR | SCC_GSMRL_ENT));
}
if (!(pinfo->flags & FLAG_CONSOLE))
- cpm_line_cr_cmd(line,CPM_CR_INIT_TRX);
+ cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
return 0;
}
static void cpm_uart_shutdown(struct uart_port *port)
{
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- int line = pinfo - cpm_uart_ports;
pr_debug("CPM uart[%d]:shutdown\n", port->line);
/* Stop uarts */
if (IS_SMC(pinfo)) {
- volatile smc_t *smcp = pinfo->smcp;
- smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
- smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX);
+ smc_t __iomem *smcp = pinfo->smcp;
+ clrbits16(&smcp->smc_smcmr, SMCMR_REN | SMCMR_TEN);
+ clrbits8(&smcp->smc_smcm, SMCM_RX | SMCM_TX);
} else {
- volatile scc_t *sccp = pinfo->sccp;
- sccp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- sccp->scc_sccm &= ~(UART_SCCM_TX | UART_SCCM_RX);
+ scc_t __iomem *sccp = pinfo->sccp;
+ clrbits32(&sccp->scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+ clrbits16(&sccp->scc_sccm, UART_SCCM_TX | UART_SCCM_RX);
}
/* Shut them really down and reinit buffer descriptors */
- if (IS_SMC(pinfo))
- cpm_line_cr_cmd(line, CPM_CR_STOP_TX);
- else
- cpm_line_cr_cmd(line, CPM_CR_GRA_STOP_TX);
+ if (IS_SMC(pinfo)) {
+ out_be16(&pinfo->smcup->smc_brkcr, 0);
+ cpm_line_cr_cmd(pinfo, CPM_CR_STOP_TX);
+ } else {
+ out_be16(&pinfo->sccup->scc_brkcr, 0);
+ cpm_line_cr_cmd(pinfo, CPM_CR_GRA_STOP_TX);
+ }
cpm_uart_initbd(pinfo);
}
u16 cval, scval, prev_mode;
int bits, sbits;
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- volatile smc_t *smcp = pinfo->smcp;
- volatile scc_t *sccp = pinfo->sccp;
+ smc_t __iomem *smcp = pinfo->smcp;
+ scc_t __iomem *sccp = pinfo->sccp;
pr_debug("CPM uart[%d]:set_termios\n", port->line);
}
/*
+ * Update the timeout
+ */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ /*
* Set up parity check flag
*/
#define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
* enables, because we want to put them back if they were
* present.
*/
- prev_mode = smcp->smc_smcmr;
- smcp->smc_smcmr = smcr_mk_clen(bits) | cval | SMCMR_SM_UART;
- smcp->smc_smcmr |= (prev_mode & (SMCMR_REN | SMCMR_TEN));
+ prev_mode = in_be16(&smcp->smc_smcmr) & (SMCMR_REN | SMCMR_TEN);
+ /* Output in *one* operation, so we don't interrupt RX/TX if they
+ * were already enabled. */
+ out_be16(&smcp->smc_smcmr, smcr_mk_clen(bits) | cval |
+ SMCMR_SM_UART | prev_mode);
} else {
- sccp->scc_psmr = (sbits << 12) | scval;
+ out_be16(&sccp->scc_psmr, (sbits << 12) | scval);
}
- cpm_set_brg(pinfo->brg - 1, baud);
+ if (pinfo->clk)
+ clk_set_rate(pinfo->clk, baud);
+ else
+ cpm_set_brg(pinfo->brg - 1, baud);
spin_unlock_irqrestore(&port->lock, flags);
-
}
static const char *cpm_uart_type(struct uart_port *port)
if (ser->type != PORT_UNKNOWN && ser->type != PORT_CPM)
ret = -EINVAL;
- if (ser->irq < 0 || ser->irq >= NR_IRQS)
+ if (ser->irq < 0 || ser->irq >= nr_irqs)
ret = -EINVAL;
if (ser->baud_base < 9600)
ret = -EINVAL;
*/
static int cpm_uart_tx_pump(struct uart_port *port)
{
- volatile cbd_t *bdp;
- unsigned char *p;
+ cbd_t __iomem *bdp;
+ u8 *p;
int count;
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
struct circ_buf *xmit = &port->info->xmit;
/* Pick next descriptor and fill from buffer */
bdp = pinfo->tx_cur;
- p = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo);
+ p = cpm2cpu_addr(in_be32(&bdp->cbd_bufaddr), pinfo);
*p++ = port->x_char;
- bdp->cbd_datlen = 1;
- bdp->cbd_sc |= BD_SC_READY;
+
+ out_be16(&bdp->cbd_datlen, 1);
+ setbits16(&bdp->cbd_sc, BD_SC_READY);
/* Get next BD. */
- if (bdp->cbd_sc & BD_SC_WRAP)
+ if (in_be16(&bdp->cbd_sc) & BD_SC_WRAP)
bdp = pinfo->tx_bd_base;
else
bdp++;
/* Pick next descriptor and fill from buffer */
bdp = pinfo->tx_cur;
- while (!(bdp->cbd_sc & BD_SC_READY) && (xmit->tail != xmit->head)) {
+ while (!(in_be16(&bdp->cbd_sc) & BD_SC_READY) &&
+ xmit->tail != xmit->head) {
count = 0;
- p = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo);
+ p = cpm2cpu_addr(in_be32(&bdp->cbd_bufaddr), pinfo);
while (count < pinfo->tx_fifosize) {
*p++ = xmit->buf[xmit->tail];
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
if (xmit->head == xmit->tail)
break;
}
- bdp->cbd_datlen = count;
- bdp->cbd_sc |= BD_SC_READY;
- __asm__("eieio");
+ out_be16(&bdp->cbd_datlen, count);
+ setbits16(&bdp->cbd_sc, BD_SC_READY);
/* Get next BD. */
- if (bdp->cbd_sc & BD_SC_WRAP)
+ if (in_be16(&bdp->cbd_sc) & BD_SC_WRAP)
bdp = pinfo->tx_bd_base;
else
bdp++;
{
int i;
u8 *mem_addr;
- volatile cbd_t *bdp;
+ cbd_t __iomem *bdp;
pr_debug("CPM uart[%d]:initbd\n", pinfo->port.line);
mem_addr = pinfo->mem_addr;
bdp = pinfo->rx_cur = pinfo->rx_bd_base;
for (i = 0; i < (pinfo->rx_nrfifos - 1); i++, bdp++) {
- bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo);
- bdp->cbd_sc = BD_SC_EMPTY | BD_SC_INTRPT;
+ out_be32(&bdp->cbd_bufaddr, cpu2cpm_addr(mem_addr, pinfo));
+ out_be16(&bdp->cbd_sc, BD_SC_EMPTY | BD_SC_INTRPT);
mem_addr += pinfo->rx_fifosize;
}
- bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo);
- bdp->cbd_sc = BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT;
+ out_be32(&bdp->cbd_bufaddr, cpu2cpm_addr(mem_addr, pinfo));
+ out_be16(&bdp->cbd_sc, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT);
/* Set the physical address of the host memory
* buffers in the buffer descriptors, and the
mem_addr = pinfo->mem_addr + L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize);
bdp = pinfo->tx_cur = pinfo->tx_bd_base;
for (i = 0; i < (pinfo->tx_nrfifos - 1); i++, bdp++) {
- bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo);
- bdp->cbd_sc = BD_SC_INTRPT;
+ out_be32(&bdp->cbd_bufaddr, cpu2cpm_addr(mem_addr, pinfo));
+ out_be16(&bdp->cbd_sc, BD_SC_INTRPT);
mem_addr += pinfo->tx_fifosize;
}
- bdp->cbd_bufaddr = cpu2cpm_addr(mem_addr, pinfo);
- bdp->cbd_sc = BD_SC_WRAP | BD_SC_INTRPT;
+ out_be32(&bdp->cbd_bufaddr, cpu2cpm_addr(mem_addr, pinfo));
+ out_be16(&bdp->cbd_sc, BD_SC_WRAP | BD_SC_INTRPT);
}
static void cpm_uart_init_scc(struct uart_cpm_port *pinfo)
{
- int line = pinfo - cpm_uart_ports;
- volatile scc_t *scp;
- volatile scc_uart_t *sup;
+ scc_t __iomem *scp;
+ scc_uart_t __iomem *sup;
pr_debug("CPM uart[%d]:init_scc\n", pinfo->port.line);
sup = pinfo->sccup;
/* Store address */
- pinfo->sccup->scc_genscc.scc_rbase = (unsigned char *)pinfo->rx_bd_base - DPRAM_BASE;
- pinfo->sccup->scc_genscc.scc_tbase = (unsigned char *)pinfo->tx_bd_base - DPRAM_BASE;
+ out_be16(&pinfo->sccup->scc_genscc.scc_rbase,
+ (u8 __iomem *)pinfo->rx_bd_base - DPRAM_BASE);
+ out_be16(&pinfo->sccup->scc_genscc.scc_tbase,
+ (u8 __iomem *)pinfo->tx_bd_base - DPRAM_BASE);
/* Set up the uart parameters in the
* parameter ram.
cpm_set_scc_fcr(sup);
- sup->scc_genscc.scc_mrblr = pinfo->rx_fifosize;
- sup->scc_maxidl = pinfo->rx_fifosize;
- sup->scc_brkcr = 1;
- sup->scc_parec = 0;
- sup->scc_frmec = 0;
- sup->scc_nosec = 0;
- sup->scc_brkec = 0;
- sup->scc_uaddr1 = 0;
- sup->scc_uaddr2 = 0;
- sup->scc_toseq = 0;
- sup->scc_char1 = 0x8000;
- sup->scc_char2 = 0x8000;
- sup->scc_char3 = 0x8000;
- sup->scc_char4 = 0x8000;
- sup->scc_char5 = 0x8000;
- sup->scc_char6 = 0x8000;
- sup->scc_char7 = 0x8000;
- sup->scc_char8 = 0x8000;
- sup->scc_rccm = 0xc0ff;
+ out_be16(&sup->scc_genscc.scc_mrblr, pinfo->rx_fifosize);
+ out_be16(&sup->scc_maxidl, pinfo->rx_fifosize);
+ out_be16(&sup->scc_brkcr, 1);
+ out_be16(&sup->scc_parec, 0);
+ out_be16(&sup->scc_frmec, 0);
+ out_be16(&sup->scc_nosec, 0);
+ out_be16(&sup->scc_brkec, 0);
+ out_be16(&sup->scc_uaddr1, 0);
+ out_be16(&sup->scc_uaddr2, 0);
+ out_be16(&sup->scc_toseq, 0);
+ out_be16(&sup->scc_char1, 0x8000);
+ out_be16(&sup->scc_char2, 0x8000);
+ out_be16(&sup->scc_char3, 0x8000);
+ out_be16(&sup->scc_char4, 0x8000);
+ out_be16(&sup->scc_char5, 0x8000);
+ out_be16(&sup->scc_char6, 0x8000);
+ out_be16(&sup->scc_char7, 0x8000);
+ out_be16(&sup->scc_char8, 0x8000);
+ out_be16(&sup->scc_rccm, 0xc0ff);
/* Send the CPM an initialize command.
*/
- cpm_line_cr_cmd(line, CPM_CR_INIT_TRX);
+ cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
*/
- scp->scc_gsmrh = 0;
- scp->scc_gsmrl =
- (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
+ out_be32(&scp->scc_gsmrh, 0);
+ out_be32(&scp->scc_gsmrl,
+ SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
/* Enable rx interrupts and clear all pending events. */
- scp->scc_sccm = 0;
- scp->scc_scce = 0xffff;
- scp->scc_dsr = 0x7e7e;
- scp->scc_psmr = 0x3000;
+ out_be16(&scp->scc_sccm, 0);
+ out_be16(&scp->scc_scce, 0xffff);
+ out_be16(&scp->scc_dsr, 0x7e7e);
+ out_be16(&scp->scc_psmr, 0x3000);
- scp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+ setbits32(&scp->scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT);
}
static void cpm_uart_init_smc(struct uart_cpm_port *pinfo)
{
- int line = pinfo - cpm_uart_ports;
- volatile smc_t *sp;
- volatile smc_uart_t *up;
+ smc_t __iomem *sp;
+ smc_uart_t __iomem *up;
pr_debug("CPM uart[%d]:init_smc\n", pinfo->port.line);
up = pinfo->smcup;
/* Store address */
- pinfo->smcup->smc_rbase = (u_char *)pinfo->rx_bd_base - DPRAM_BASE;
- pinfo->smcup->smc_tbase = (u_char *)pinfo->tx_bd_base - DPRAM_BASE;
+ out_be16(&pinfo->smcup->smc_rbase,
+ (u8 __iomem *)pinfo->rx_bd_base - DPRAM_BASE);
+ out_be16(&pinfo->smcup->smc_tbase,
+ (u8 __iomem *)pinfo->tx_bd_base - DPRAM_BASE);
/*
* In case SMC1 is being relocated...
*/
#if defined (CONFIG_I2C_SPI_SMC1_UCODE_PATCH)
- up->smc_rbptr = pinfo->smcup->smc_rbase;
- up->smc_tbptr = pinfo->smcup->smc_tbase;
- up->smc_rstate = 0;
- up->smc_tstate = 0;
- up->smc_brkcr = 1; /* number of break chars */
- up->smc_brkec = 0;
+ out_be16(&up->smc_rbptr, in_be16(&pinfo->smcup->smc_rbase));
+ out_be16(&up->smc_tbptr, in_be16(&pinfo->smcup->smc_tbase));
+ out_be32(&up->smc_rstate, 0);
+ out_be32(&up->smc_tstate, 0);
+ out_be16(&up->smc_brkcr, 1); /* number of break chars */
+ out_be16(&up->smc_brkec, 0);
#endif
/* Set up the uart parameters in the
cpm_set_smc_fcr(up);
/* Using idle charater time requires some additional tuning. */
- up->smc_mrblr = pinfo->rx_fifosize;
- up->smc_maxidl = pinfo->rx_fifosize;
- up->smc_brklen = 0;
- up->smc_brkec = 0;
- up->smc_brkcr = 1;
+ out_be16(&up->smc_mrblr, pinfo->rx_fifosize);
+ out_be16(&up->smc_maxidl, pinfo->rx_fifosize);
+ out_be16(&up->smc_brklen, 0);
+ out_be16(&up->smc_brkec, 0);
+ out_be16(&up->smc_brkcr, 1);
- cpm_line_cr_cmd(line, CPM_CR_INIT_TRX);
+ cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX);
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
*/
- sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
+ out_be16(&sp->smc_smcmr, smcr_mk_clen(9) | SMCMR_SM_UART);
/* Enable only rx interrupts clear all pending events. */
- sp->smc_smcm = 0;
- sp->smc_smce = 0xff;
+ out_8(&sp->smc_smcm, 0);
+ out_8(&sp->smc_smce, 0xff);
- sp->smc_smcmr |= (SMCMR_REN | SMCMR_TEN);
+ setbits16(&sp->smc_smcmr, SMCMR_REN | SMCMR_TEN);
}
/*
return 0;
if (IS_SMC(pinfo)) {
- pinfo->smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX);
- pinfo->smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+ clrbits8(&pinfo->smcp->smc_smcm, SMCM_RX | SMCM_TX);
+ clrbits16(&pinfo->smcp->smc_smcmr, SMCMR_REN | SMCMR_TEN);
} else {
- pinfo->sccp->scc_sccm &= ~(UART_SCCM_TX | UART_SCCM_RX);
- pinfo->sccp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+ clrbits16(&pinfo->sccp->scc_sccm, UART_SCCM_TX | UART_SCCM_RX);
+ clrbits32(&pinfo->sccp->scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT);
}
ret = cpm_uart_allocbuf(pinfo, 0);
cpm_uart_request_port(port);
}
}
+
+#ifdef CONFIG_CONSOLE_POLL
+/* Serial polling routines for writing and reading from the uart while
+ * in an interrupt or debug context.
+ */
+
+#define GDB_BUF_SIZE 512 /* power of 2, please */
+
+static char poll_buf[GDB_BUF_SIZE];
+static char *pollp;
+static int poll_chars;
+
+static int poll_wait_key(char *obuf, struct uart_cpm_port *pinfo)
+{
+ u_char c, *cp;
+ volatile cbd_t *bdp;
+ int i;
+
+ /* Get the address of the host memory buffer.
+ */
+ bdp = pinfo->rx_cur;
+ while (bdp->cbd_sc & BD_SC_EMPTY)
+ ;
+
+ /* If the buffer address is in the CPM DPRAM, don't
+ * convert it.
+ */
+ cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo);
+
+ if (obuf) {
+ i = c = bdp->cbd_datlen;
+ while (i-- > 0)
+ *obuf++ = *cp++;
+ } else
+ c = *cp;
+ bdp->cbd_sc &= ~(BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV | BD_SC_ID);
+ bdp->cbd_sc |= BD_SC_EMPTY;
+
+ if (bdp->cbd_sc & BD_SC_WRAP)
+ bdp = pinfo->rx_bd_base;
+ else
+ bdp++;
+ pinfo->rx_cur = (cbd_t *)bdp;
+
+ return (int)c;
+}
+
+static int cpm_get_poll_char(struct uart_port *port)
+{
+ struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
+
+ if (!serial_polled) {
+ serial_polled = 1;
+ poll_chars = 0;
+ }
+ if (poll_chars <= 0) {
+ poll_chars = poll_wait_key(poll_buf, pinfo);
+ pollp = poll_buf;
+ }
+ poll_chars--;
+ return *pollp++;
+}
+
+static void cpm_put_poll_char(struct uart_port *port,
+ unsigned char c)
+{
+ struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
+ static char ch[2];
+
+ ch[0] = (char)c;
+ cpm_uart_early_write(pinfo->port.line, ch, 1);
+}
+#endif /* CONFIG_CONSOLE_POLL */
+
static struct uart_ops cpm_uart_pops = {
.tx_empty = cpm_uart_tx_empty,
.set_mctrl = cpm_uart_set_mctrl,
.request_port = cpm_uart_request_port,
.config_port = cpm_uart_config_port,
.verify_port = cpm_uart_verify_port,
-};
-
-struct uart_cpm_port cpm_uart_ports[UART_NR] = {
- [UART_SMC1] = {
- .port = {
- .irq = SMC1_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SMC1].port.lock),
- },
- .flags = FLAG_SMC,
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = smc1_lineif,
- },
- [UART_SMC2] = {
- .port = {
- .irq = SMC2_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SMC2].port.lock),
- },
- .flags = FLAG_SMC,
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = smc2_lineif,
-#ifdef CONFIG_SERIAL_CPM_ALT_SMC2
- .is_portb = 1,
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_get_char = cpm_get_poll_char,
+ .poll_put_char = cpm_put_poll_char,
#endif
- },
- [UART_SCC1] = {
- .port = {
- .irq = SCC1_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC1].port.lock),
- },
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = scc1_lineif,
- .wait_closing = SCC_WAIT_CLOSING,
- },
- [UART_SCC2] = {
- .port = {
- .irq = SCC2_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC2].port.lock),
- },
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = scc2_lineif,
- .wait_closing = SCC_WAIT_CLOSING,
- },
- [UART_SCC3] = {
- .port = {
- .irq = SCC3_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC3].port.lock),
- },
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = scc3_lineif,
- .wait_closing = SCC_WAIT_CLOSING,
- },
- [UART_SCC4] = {
- .port = {
- .irq = SCC4_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC4].port.lock),
- },
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = scc4_lineif,
- .wait_closing = SCC_WAIT_CLOSING,
- },
};
-int cpm_uart_drv_get_platform_data(struct platform_device *pdev, int is_con)
+struct uart_cpm_port cpm_uart_ports[UART_NR];
+
+static int cpm_uart_init_port(struct device_node *np,
+ struct uart_cpm_port *pinfo)
{
- struct resource *r;
- struct fs_uart_platform_info *pdata = pdev->dev.platform_data;
- int idx; /* It is UART_SMCx or UART_SCCx index */
- struct uart_cpm_port *pinfo;
- int line;
- u32 mem, pram;
+ const u32 *data;
+ void __iomem *mem, *pram;
+ int len;
+ int ret;
+ int i;
- idx = pdata->fs_no = fs_uart_get_id(pdata);
+ data = of_get_property(np, "clock", NULL);
+ if (data) {
+ struct clk *clk = clk_get(NULL, (const char*)data);
+ if (!IS_ERR(clk))
+ pinfo->clk = clk;
+ }
+ if (!pinfo->clk) {
+ data = of_get_property(np, "fsl,cpm-brg", &len);
+ if (!data || len != 4) {
+ printk(KERN_ERR "CPM UART %s has no/invalid "
+ "fsl,cpm-brg property.\n", np->name);
+ return -EINVAL;
+ }
+ pinfo->brg = *data;
+ }
- line = cpm_uart_id2nr(idx);
- if(line < 0) {
- printk(KERN_ERR"%s(): port %d is not registered", __FUNCTION__, idx);
+ data = of_get_property(np, "fsl,cpm-command", &len);
+ if (!data || len != 4) {
+ printk(KERN_ERR "CPM UART %s has no/invalid "
+ "fsl,cpm-command property.\n", np->name);
return -EINVAL;
}
-
- pinfo = (struct uart_cpm_port *) &cpm_uart_ports[idx];
-
- pinfo->brg = pdata->brg;
-
- if (!is_con) {
- pinfo->port.line = line;
- pinfo->port.flags = UPF_BOOT_AUTOCONF;
+ pinfo->command = *data;
+
+ mem = of_iomap(np, 0);
+ if (!mem)
+ return -ENOMEM;
+
+ if (of_device_is_compatible(np, "fsl,cpm1-scc-uart") ||
+ of_device_is_compatible(np, "fsl,cpm2-scc-uart")) {
+ pinfo->sccp = mem;
+ pinfo->sccup = pram = cpm_uart_map_pram(pinfo, np);
+ } else if (of_device_is_compatible(np, "fsl,cpm1-smc-uart") ||
+ of_device_is_compatible(np, "fsl,cpm2-smc-uart")) {
+ pinfo->flags |= FLAG_SMC;
+ pinfo->smcp = mem;
+ pinfo->smcup = pram = cpm_uart_map_pram(pinfo, np);
+ } else {
+ ret = -ENODEV;
+ goto out_mem;
}
- if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs")))
- return -EINVAL;
- mem = (u32)ioremap(r->start, r->end - r->start + 1);
+ if (!pram) {
+ ret = -ENOMEM;
+ goto out_mem;
+ }
- if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pram")))
- return -EINVAL;
- pram = (u32)ioremap(r->start, r->end - r->start + 1);
+ pinfo->tx_nrfifos = TX_NUM_FIFO;
+ pinfo->tx_fifosize = TX_BUF_SIZE;
+ pinfo->rx_nrfifos = RX_NUM_FIFO;
+ pinfo->rx_fifosize = RX_BUF_SIZE;
- if(idx > fsid_smc2_uart) {
- pinfo->sccp = (scc_t *)mem;
- pinfo->sccup = (scc_uart_t *)pram;
- } else {
- pinfo->smcp = (smc_t *)mem;
- pinfo->smcup = (smc_uart_t *)pram;
+ pinfo->port.uartclk = ppc_proc_freq;
+ pinfo->port.mapbase = (unsigned long)mem;
+ pinfo->port.type = PORT_CPM;
+ pinfo->port.ops = &cpm_uart_pops,
+ pinfo->port.iotype = UPIO_MEM;
+ pinfo->port.fifosize = pinfo->tx_nrfifos * pinfo->tx_fifosize;
+ spin_lock_init(&pinfo->port.lock);
+
+ pinfo->port.irq = of_irq_to_resource(np, 0, NULL);
+ if (pinfo->port.irq == NO_IRQ) {
+ ret = -EINVAL;
+ goto out_pram;
}
- pinfo->tx_nrfifos = pdata->tx_num_fifo;
- pinfo->tx_fifosize = pdata->tx_buf_size;
- pinfo->rx_nrfifos = pdata->rx_num_fifo;
- pinfo->rx_fifosize = pdata->rx_buf_size;
+ for (i = 0; i < NUM_GPIOS; i++)
+ pinfo->gpios[i] = of_get_gpio(np, i);
- pinfo->port.uartclk = pdata->uart_clk;
- pinfo->port.mapbase = (unsigned long)mem;
- pinfo->port.irq = platform_get_irq(pdev, 0);
+ return cpm_uart_request_port(&pinfo->port);
- return 0;
+out_pram:
+ cpm_uart_unmap_pram(pinfo, pram);
+out_mem:
+ iounmap(mem);
+ return ret;
}
#ifdef CONFIG_SERIAL_CPM_CONSOLE
static void cpm_uart_console_write(struct console *co, const char *s,
u_int count)
{
- struct uart_cpm_port *pinfo =
- &cpm_uart_ports[cpm_uart_port_map[co->index]];
+ struct uart_cpm_port *pinfo = &cpm_uart_ports[co->index];
unsigned int i;
- volatile cbd_t *bdp, *bdbase;
- volatile unsigned char *cp;
+ cbd_t __iomem *bdp, *bdbase;
+ unsigned char *cp;
+ unsigned long flags;
+ int nolock = oops_in_progress;
+
+ if (unlikely(nolock)) {
+ local_irq_save(flags);
+ } else {
+ spin_lock_irqsave(&pinfo->port.lock, flags);
+ }
/* Get the address of the host memory buffer.
*/
* Ready indicates output is ready, and xmt is doing
* that, not that it is ready for us to send.
*/
- while ((bdp->cbd_sc & BD_SC_READY) != 0)
+ while ((in_be16(&bdp->cbd_sc) & BD_SC_READY) != 0)
;
/* Send the character out.
* If the buffer address is in the CPM DPRAM, don't
* convert it.
*/
- cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo);
-
+ cp = cpm2cpu_addr(in_be32(&bdp->cbd_bufaddr), pinfo);
*cp = *s;
- bdp->cbd_datlen = 1;
- bdp->cbd_sc |= BD_SC_READY;
+ out_be16(&bdp->cbd_datlen, 1);
+ setbits16(&bdp->cbd_sc, BD_SC_READY);
- if (bdp->cbd_sc & BD_SC_WRAP)
+ if (in_be16(&bdp->cbd_sc) & BD_SC_WRAP)
bdp = bdbase;
else
bdp++;
/* if a LF, also do CR... */
if (*s == 10) {
- while ((bdp->cbd_sc & BD_SC_READY) != 0)
+ while ((in_be16(&bdp->cbd_sc) & BD_SC_READY) != 0)
;
- cp = cpm2cpu_addr(bdp->cbd_bufaddr, pinfo);
-
+ cp = cpm2cpu_addr(in_be32(&bdp->cbd_bufaddr), pinfo);
*cp = 13;
- bdp->cbd_datlen = 1;
- bdp->cbd_sc |= BD_SC_READY;
- if (bdp->cbd_sc & BD_SC_WRAP)
+ out_be16(&bdp->cbd_datlen, 1);
+ setbits16(&bdp->cbd_sc, BD_SC_READY);
+
+ if (in_be16(&bdp->cbd_sc) & BD_SC_WRAP)
bdp = bdbase;
else
bdp++;
* Finally, Wait for transmitter & holding register to empty
* and restore the IER
*/
- while ((bdp->cbd_sc & BD_SC_READY) != 0)
+ while ((in_be16(&bdp->cbd_sc) & BD_SC_READY) != 0)
;
- pinfo->tx_cur = (volatile cbd_t *) bdp;
+ pinfo->tx_cur = bdp;
+
+ if (unlikely(nolock)) {
+ local_irq_restore(flags);
+ } else {
+ spin_unlock_irqrestore(&pinfo->port.lock, flags);
+ }
}
static int __init cpm_uart_console_setup(struct console *co, char *options)
{
- struct uart_port *port;
- struct uart_cpm_port *pinfo;
int baud = 38400;
int bits = 8;
int parity = 'n';
int flow = 'n';
int ret;
+ struct uart_cpm_port *pinfo;
+ struct uart_port *port;
- struct fs_uart_platform_info *pdata;
- struct platform_device* pdev = early_uart_get_pdev(co->index);
+ struct device_node *np = NULL;
+ int i = 0;
- if (!pdev) {
- pr_info("cpm_uart: console: compat mode\n");
- /* compatibility - will be cleaned up */
- cpm_uart_init_portdesc();
+ if (co->index >= UART_NR) {
+ printk(KERN_ERR "cpm_uart: console index %d too high\n",
+ co->index);
+ return -ENODEV;
}
- port =
- (struct uart_port *)&cpm_uart_ports[cpm_uart_port_map[co->index]];
- pinfo = (struct uart_cpm_port *)port;
- if (!pdev) {
- if (pinfo->set_lineif)
- pinfo->set_lineif(pinfo);
- } else {
- pdata = pdev->dev.platform_data;
- if (pdata)
- if (pdata->init_ioports)
- pdata->init_ioports(pdata);
+ do {
+ np = of_find_node_by_type(np, "serial");
+ if (!np)
+ return -ENODEV;
- cpm_uart_drv_get_platform_data(pdev, 1);
- }
+ if (!of_device_is_compatible(np, "fsl,cpm1-smc-uart") &&
+ !of_device_is_compatible(np, "fsl,cpm1-scc-uart") &&
+ !of_device_is_compatible(np, "fsl,cpm2-smc-uart") &&
+ !of_device_is_compatible(np, "fsl,cpm2-scc-uart"))
+ i--;
+ } while (i++ != co->index);
+
+ pinfo = &cpm_uart_ports[co->index];
pinfo->flags |= FLAG_CONSOLE;
+ port = &pinfo->port;
+
+ ret = cpm_uart_init_port(np, pinfo);
+ of_node_put(np);
+ if (ret)
+ return ret;
if (options) {
uart_parse_options(options, &baud, &parity, &bits, &flow);
baud = 9600;
}
+#ifdef CONFIG_PPC_EARLY_DEBUG_CPM
+ udbg_putc = NULL;
+#endif
+
if (IS_SMC(pinfo)) {
- pinfo->smcp->smc_smcm &= ~(SMCM_RX | SMCM_TX);
- pinfo->smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+ out_be16(&pinfo->smcup->smc_brkcr, 0);
+ cpm_line_cr_cmd(pinfo, CPM_CR_STOP_TX);
+ clrbits8(&pinfo->smcp->smc_smcm, SMCM_RX | SMCM_TX);
+ clrbits16(&pinfo->smcp->smc_smcmr, SMCMR_REN | SMCMR_TEN);
} else {
- pinfo->sccp->scc_sccm &= ~(UART_SCCM_TX | UART_SCCM_RX);
- pinfo->sccp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+ out_be16(&pinfo->sccup->scc_brkcr, 0);
+ cpm_line_cr_cmd(pinfo, CPM_CR_GRA_STOP_TX);
+ clrbits16(&pinfo->sccp->scc_sccm, UART_SCCM_TX | UART_SCCM_RX);
+ clrbits32(&pinfo->sccp->scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT);
}
ret = cpm_uart_allocbuf(pinfo, 1);
cpm_uart_init_scc(pinfo);
uart_set_options(port, co, baud, parity, bits, flow);
+ cpm_line_cr_cmd(pinfo, CPM_CR_RESTART_TX);
return 0;
}
.data = &cpm_reg,
};
-int __init cpm_uart_console_init(void)
+static int __init cpm_uart_console_init(void)
{
register_console(&cpm_scc_uart_console);
return 0;
.major = SERIAL_CPM_MAJOR,
.minor = SERIAL_CPM_MINOR,
.cons = CPM_UART_CONSOLE,
+ .nr = UART_NR,
};
-static int cpm_uart_drv_probe(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct fs_uart_platform_info *pdata;
- int ret = -ENODEV;
- if(!pdev) {
- printk(KERN_ERR"CPM UART: platform data missing!\n");
- return ret;
- }
+static int probe_index;
- pdata = pdev->dev.platform_data;
+static int __devinit cpm_uart_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ int index = probe_index++;
+ struct uart_cpm_port *pinfo = &cpm_uart_ports[index];
+ int ret;
- if ((ret = cpm_uart_drv_get_platform_data(pdev, 0)))
- return ret;
+ pinfo->port.line = index;
- pr_debug("cpm_uart_drv_probe: Adding CPM UART %d\n", cpm_uart_id2nr(pdata->fs_no));
+ if (index >= UART_NR)
+ return -ENODEV;
- if (pdata->init_ioports)
- pdata->init_ioports(pdata);
+ dev_set_drvdata(&ofdev->dev, pinfo);
- ret = uart_add_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port);
+ ret = cpm_uart_init_port(ofdev->node, pinfo);
+ if (ret)
+ return ret;
- return ret;
+ return uart_add_one_port(&cpm_reg, &pinfo->port);
}
-static int cpm_uart_drv_remove(struct device *dev)
+static int __devexit cpm_uart_remove(struct of_device *ofdev)
{
- struct platform_device *pdev = to_platform_device(dev);
- struct fs_uart_platform_info *pdata = pdev->dev.platform_data;
-
- pr_debug("cpm_uart_drv_remove: Removing CPM UART %d\n",
- cpm_uart_id2nr(pdata->fs_no));
-
- uart_remove_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port);
- return 0;
+ struct uart_cpm_port *pinfo = dev_get_drvdata(&ofdev->dev);
+ return uart_remove_one_port(&cpm_reg, &pinfo->port);
}
-static struct device_driver cpm_smc_uart_driver = {
- .name = "fsl-cpm-smc:uart",
- .bus = &platform_bus_type,
- .probe = cpm_uart_drv_probe,
- .remove = cpm_uart_drv_remove,
+static struct of_device_id cpm_uart_match[] = {
+ {
+ .compatible = "fsl,cpm1-smc-uart",
+ },
+ {
+ .compatible = "fsl,cpm1-scc-uart",
+ },
+ {
+ .compatible = "fsl,cpm2-smc-uart",
+ },
+ {
+ .compatible = "fsl,cpm2-scc-uart",
+ },
+ {}
};
-static struct device_driver cpm_scc_uart_driver = {
- .name = "fsl-cpm-scc:uart",
- .bus = &platform_bus_type,
- .probe = cpm_uart_drv_probe,
- .remove = cpm_uart_drv_remove,
-};
+static struct of_platform_driver cpm_uart_driver = {
+ .name = "cpm_uart",
+ .match_table = cpm_uart_match,
+ .probe = cpm_uart_probe,
+ .remove = cpm_uart_remove,
+ };
-/*
- This is supposed to match uart devices on platform bus,
- */
-static int match_is_uart (struct device* dev, void* data)
+static int __init cpm_uart_init(void)
{
- struct platform_device* pdev = container_of(dev, struct platform_device, dev);
- int ret = 0;
- /* this was setfunc as uart */
- if(strstr(pdev->name,":uart")) {
- ret = 1;
- }
- return ret;
-}
-
-
-static int cpm_uart_init(void) {
-
- int ret;
- int i;
- struct device *dev;
- printk(KERN_INFO "Serial: CPM driver $Revision: 0.02 $\n");
-
- /* lookup the bus for uart devices */
- dev = bus_find_device(&platform_bus_type, NULL, 0, match_is_uart);
-
- /* There are devices on the bus - all should be OK */
- if (dev) {
- cpm_uart_count();
- cpm_reg.nr = cpm_uart_nr;
+ int ret = uart_register_driver(&cpm_reg);
+ if (ret)
+ return ret;
- if (!(ret = uart_register_driver(&cpm_reg))) {
- if ((ret = driver_register(&cpm_smc_uart_driver))) {
- uart_unregister_driver(&cpm_reg);
- return ret;
- }
- if ((ret = driver_register(&cpm_scc_uart_driver))) {
- driver_unregister(&cpm_scc_uart_driver);
- uart_unregister_driver(&cpm_reg);
- }
- }
- } else {
- /* No capable platform devices found - falling back to legacy mode */
- pr_info("cpm_uart: WARNING: no UART devices found on platform bus!\n");
- pr_info(
- "cpm_uart: the driver will guess configuration, but this mode is no longer supported.\n");
-
- /* Don't run this again, if the console driver did it already */
- if (cpm_uart_nr == 0)
- cpm_uart_init_portdesc();
-
- cpm_reg.nr = cpm_uart_nr;
- ret = uart_register_driver(&cpm_reg);
-
- if (ret)
- return ret;
-
- for (i = 0; i < cpm_uart_nr; i++) {
- int con = cpm_uart_port_map[i];
- cpm_uart_ports[con].port.line = i;
- cpm_uart_ports[con].port.flags = UPF_BOOT_AUTOCONF;
- if (cpm_uart_ports[con].set_lineif)
- cpm_uart_ports[con].set_lineif(&cpm_uart_ports[con]);
- uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port);
- }
+ ret = of_register_platform_driver(&cpm_uart_driver);
+ if (ret)
+ uart_unregister_driver(&cpm_reg);
- }
return ret;
}
static void __exit cpm_uart_exit(void)
{
- driver_unregister(&cpm_scc_uart_driver);
- driver_unregister(&cpm_smc_uart_driver);
+ of_unregister_platform_driver(&cpm_uart_driver);
uart_unregister_driver(&cpm_reg);
}