/*
- * File: drivers/serial/bfin_5xx.c
- * Based on: Based on drivers/serial/sa1100.c
- * Author: Aubrey Li <aubrey.li@analog.com>
+ * Blackfin On-Chip Serial Driver
*
- * Created:
- * Description: Driver for blackfin 5xx serial ports
+ * Copyright 2006-2007 Analog Devices Inc.
*
- * Modified:
- * Copyright 2006 Analog Devices Inc.
+ * Enter bugs at http://blackfin.uclinux.org/
*
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * Licensed under the GPL-2 or later.
*/
#if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define DMA_RX_XCOUNT 512
#define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT)
-#define DMA_RX_FLUSH_JIFFIES 5
+#define DMA_RX_FLUSH_JIFFIES (HZ / 50)
#ifdef CONFIG_SERIAL_BFIN_DMA
static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
#else
-static void bfin_serial_do_work(struct work_struct *work);
static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
-static void local_put_char(struct bfin_serial_port *uart, char ch);
#endif
static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
static void bfin_serial_stop_tx(struct uart_port *port)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ struct circ_buf *xmit = &uart->port.info->xmit;
+#if !defined(CONFIG_BF54x) && !defined(CONFIG_SERIAL_BFIN_DMA)
+ unsigned short ier;
+#endif
+
+ while (!(UART_GET_LSR(uart) & TEMT))
+ cpu_relax();
#ifdef CONFIG_SERIAL_BFIN_DMA
disable_dma(uart->tx_dma_channel);
+ xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
+ uart->port.icount.tx += uart->tx_count;
+ uart->tx_count = 0;
+ uart->tx_done = 1;
+#else
+#ifdef CONFIG_BF54x
+ /* Clear TFI bit */
+ UART_PUT_LSR(uart, TFI);
+ UART_CLEAR_IER(uart, ETBEI);
#else
- unsigned short ier;
-
ier = UART_GET_IER(uart);
ier &= ~ETBEI;
UART_PUT_IER(uart, ier);
#endif
+#endif
}
/*
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
#ifdef CONFIG_SERIAL_BFIN_DMA
- bfin_serial_dma_tx_chars(uart);
+ if (uart->tx_done)
+ bfin_serial_dma_tx_chars(uart);
+#else
+#ifdef CONFIG_BF54x
+ UART_SET_IER(uart, ETBEI);
#else
unsigned short ier;
ier = UART_GET_IER(uart);
ier |= ETBEI;
UART_PUT_IER(uart, ier);
+#endif
bfin_serial_tx_chars(uart);
#endif
}
static void bfin_serial_stop_rx(struct uart_port *port)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+#ifdef CONFIG_KGDB_UART
+ if (uart->port.line != CONFIG_KGDB_UART_PORT) {
+#endif
+#ifdef CONFIG_BF54x
+ UART_CLEAR_IER(uart, ERBFI);
+#else
unsigned short ier;
ier = UART_GET_IER(uart);
-#ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT)
-#endif
ier &= ~ERBFI;
UART_PUT_IER(uart, ier);
+#endif
+#ifdef CONFIG_KGDB_UART
+ }
+#endif
}
/*
{
struct bfin_serial_port *uart;
- if (CONFIG_KGDB_UART_PORT<0 || CONFIG_KGDB_UART_PORT>=NR_PORTS)
+ if (CONFIG_KGDB_UART_PORT < 0
+ || CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS)
uart = &bfin_serial_ports[0];
else
uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
while (!(UART_GET_LSR(uart) & THRE)) {
- __builtin_bfin_ssync();
+ SSYNC();
}
+
+#ifndef CONFIG_BF54x
UART_PUT_LCR(uart, UART_GET_LCR(uart)&(~DLAB));
- __builtin_bfin_ssync();
+ SSYNC();
+#endif
UART_PUT_CHAR(uart, (unsigned char)chr);
- __builtin_bfin_ssync();
+ SSYNC();
}
int kgdb_get_debug_char(void)
struct bfin_serial_port *uart;
unsigned char chr;
- if (CONFIG_KGDB_UART_PORT<0 || CONFIG_KGDB_UART_PORT>=NR_PORTS)
+ if (CONFIG_KGDB_UART_PORT < 0
+ || CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS)
uart = &bfin_serial_ports[0];
else
uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
while(!(UART_GET_LSR(uart) & DR)) {
- __builtin_bfin_ssync();
+ SSYNC();
}
+#ifndef CONFIG_BF54x
UART_PUT_LCR(uart, UART_GET_LCR(uart)&(~DLAB));
- __builtin_bfin_ssync();
+ SSYNC();
+#endif
chr = UART_GET_CHAR(uart);
- __builtin_bfin_ssync();
+ SSYNC();
return chr;
}
#endif
-#ifdef CONFIG_SERIAL_BFIN_PIO
-static void local_put_char(struct bfin_serial_port *uart, char ch)
-{
- unsigned short status;
- int flags = 0;
-
- spin_lock_irqsave(&uart->port.lock, flags);
-
- do {
- status = UART_GET_LSR(uart);
- } while (!(status & THRE));
-
- UART_PUT_CHAR(uart, ch);
- SSYNC();
-
- spin_unlock_irqrestore(&uart->port.lock, flags);
-}
+#if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO)
+# define UART_GET_ANOMALY_THRESHOLD(uart) ((uart)->anomaly_threshold)
+# define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v))
+#else
+# define UART_GET_ANOMALY_THRESHOLD(uart) 0
+# define UART_SET_ANOMALY_THRESHOLD(uart, v)
+#endif
+#ifdef CONFIG_SERIAL_BFIN_PIO
static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
{
struct tty_struct *tty = uart->port.info->tty;
unsigned int status, ch, flg;
+ static struct timeval anomaly_start = { .tv_sec = 0 };
#ifdef CONFIG_KGDB_UART
struct pt_regs *regs = get_irq_regs();
#endif
-#ifdef BF533_FAMILY
- static int in_break = 0;
-#endif
status = UART_GET_LSR(uart);
+ UART_CLEAR_LSR(uart);
+
ch = UART_GET_CHAR(uart);
uart->port.icount.rx++;
}
}
#endif
-
-#ifdef BF533_FAMILY
- /* The BF533 family of processors have a nice misbehavior where
- * they continuously generate characters for a "single" break.
- * We have to basically ignore this flood until the "next" valid
- * character comes across. All other Blackfin families operate
- * properly though.
- */
- if (in_break) {
- if (ch != 0) {
- in_break = 0;
- ch = UART_GET_CHAR(uart);
- if (bfin_revid() < 5)
- return;
- } else
+
+ if (ANOMALY_05000363) {
+ /* The BF533 (and BF561) family of processors have a nice anomaly
+ * where they continuously generate characters for a "single" break.
+ * We have to basically ignore this flood until the "next" valid
+ * character comes across. Due to the nature of the flood, it is
+ * not possible to reliably catch bytes that are sent too quickly
+ * after this break. So application code talking to the Blackfin
+ * which sends a break signal must allow at least 1.5 character
+ * times after the end of the break for things to stabilize. This
+ * timeout was picked as it must absolutely be larger than 1
+ * character time +/- some percent. So 1.5 sounds good. All other
+ * Blackfin families operate properly. Woo.
+ */
+ if (anomaly_start.tv_sec) {
+ struct timeval curr;
+ suseconds_t usecs;
+
+ if ((~ch & (~ch + 1)) & 0xff)
+ goto known_good_char;
+
+ do_gettimeofday(&curr);
+ if (curr.tv_sec - anomaly_start.tv_sec > 1)
+ goto known_good_char;
+
+ usecs = 0;
+ if (curr.tv_sec != anomaly_start.tv_sec)
+ usecs += USEC_PER_SEC;
+ usecs += curr.tv_usec - anomaly_start.tv_usec;
+
+ if (usecs > UART_GET_ANOMALY_THRESHOLD(uart))
+ goto known_good_char;
+
+ if (ch)
+ anomaly_start.tv_sec = 0;
+ else
+ anomaly_start = curr;
+
return;
+
+ known_good_char:
+ anomaly_start.tv_sec = 0;
+ }
}
-#endif
if (status & BI) {
-#ifdef BF533_FAMILY
- in_break = 1;
-#endif
+ if (ANOMALY_05000363)
+ if (bfin_revid() < 5)
+ do_gettimeofday(&anomaly_start);
uart->port.icount.brk++;
if (uart_handle_break(&uart->port))
goto ignore_char;
UART_PUT_CHAR(uart, uart->port.x_char);
uart->port.icount.tx++;
uart->port.x_char = 0;
- return;
}
/*
* Check the modem control lines before
return;
}
- local_put_char(uart, xmit->buf[xmit->tail]);
- xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- uart->port.icount.tx++;
+ while ((UART_GET_LSR(uart) & THRE) && xmit->tail != xmit->head) {
+ UART_PUT_CHAR(uart, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ uart->port.icount.tx++;
+ SSYNC();
+ }
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uart->port);
struct bfin_serial_port *uart = dev_id;
spin_lock(&uart->port.lock);
- while ((UART_GET_IIR(uart) & IIR_STATUS) == IIR_RX_READY)
+ while (UART_GET_LSR(uart) & DR)
bfin_serial_rx_chars(uart);
spin_unlock(&uart->port.lock);
+
return IRQ_HANDLED;
}
struct bfin_serial_port *uart = dev_id;
spin_lock(&uart->port.lock);
- while ((UART_GET_IIR(uart) & IIR_STATUS) == IIR_TX_READY)
+ if (UART_GET_LSR(uart) & THRE)
bfin_serial_tx_chars(uart);
spin_unlock(&uart->port.lock);
+
return IRQ_HANDLED;
}
+#endif
-
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
static void bfin_serial_do_work(struct work_struct *work)
{
struct bfin_serial_port *uart = container_of(work, struct bfin_serial_port, cts_workqueue);
bfin_serial_mctrl_check(uart);
}
-
#endif
#ifdef CONFIG_SERIAL_BFIN_DMA
{
struct circ_buf *xmit = &uart->port.info->xmit;
unsigned short ier;
- int flags = 0;
-
- if (!uart->tx_done)
- return;
uart->tx_done = 0;
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
+ uart->tx_count = 0;
+ uart->tx_done = 1;
+ return;
+ }
+
if (uart->port.x_char) {
UART_PUT_CHAR(uart, uart->port.x_char);
uart->port.icount.tx++;
uart->port.x_char = 0;
- uart->tx_done = 1;
- return;
}
+
/*
* Check the modem control lines before
* transmitting anything.
*/
bfin_serial_mctrl_check(uart);
- if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
- bfin_serial_stop_tx(&uart->port);
- uart->tx_done = 1;
- return;
- }
-
- spin_lock_irqsave(&uart->port.lock, flags);
uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
uart->tx_count = UART_XMIT_SIZE - xmit->tail;
set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
INTR_ON_BUF,
DIMENSION_LINEAR,
- DATA_SIZE_8));
+ DATA_SIZE_8,
+ DMA_SYNC_RESTART));
set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
set_dma_x_modify(uart->tx_dma_channel, 1);
enable_dma(uart->tx_dma_channel);
+
+#ifdef CONFIG_BF54x
+ UART_SET_IER(uart, ETBEI);
+#else
ier = UART_GET_IER(uart);
ier |= ETBEI;
UART_PUT_IER(uart, ier);
- spin_unlock_irqrestore(&uart->port.lock, flags);
+#endif
}
static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
int i, flg, status;
status = UART_GET_LSR(uart);
- uart->port.icount.rx += CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail, UART_XMIT_SIZE);;
+ UART_CLEAR_LSR(uart);
+
+ uart->port.icount.rx +=
+ CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail,
+ UART_XMIT_SIZE);
if (status & BI) {
uart->port.icount.brk++;
else
flg = TTY_NORMAL;
- for (i = uart->rx_dma_buf.head; i < uart->rx_dma_buf.tail; i++) {
- if (uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
- goto dma_ignore_char;
- uart_insert_char(&uart->port, status, OE, uart->rx_dma_buf.buf[i], flg);
+ for (i = uart->rx_dma_buf.tail; i != uart->rx_dma_buf.head; i++) {
+ if (i >= UART_XMIT_SIZE)
+ i = 0;
+ if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
+ uart_insert_char(&uart->port, status, OE,
+ uart->rx_dma_buf.buf[i], flg);
}
dma_ignore_char:
void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
{
int x_pos, pos;
- int flags = 0;
-
- bfin_serial_dma_tx_chars(uart);
- spin_lock_irqsave(&uart->port.lock, flags);
- x_pos = DMA_RX_XCOUNT - get_dma_curr_xcount(uart->rx_dma_channel);
+ uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
+ x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
+ uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
+ if (uart->rx_dma_nrows == DMA_RX_YCOUNT)
+ uart->rx_dma_nrows = 0;
+ x_pos = DMA_RX_XCOUNT - x_pos;
if (x_pos == DMA_RX_XCOUNT)
x_pos = 0;
pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
-
- if (pos>uart->rx_dma_buf.tail) {
- uart->rx_dma_buf.tail = pos;
+ if (pos != uart->rx_dma_buf.tail) {
+ uart->rx_dma_buf.head = pos;
bfin_serial_dma_rx_chars(uart);
- uart->rx_dma_buf.head = uart->rx_dma_buf.tail;
+ uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
}
- spin_unlock_irqrestore(&uart->port.lock, flags);
- uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
- add_timer(&(uart->rx_dma_timer));
+
+ mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
}
static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
spin_lock(&uart->port.lock);
if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
- clear_dma_irqstat(uart->tx_dma_channel);
disable_dma(uart->tx_dma_channel);
+ clear_dma_irqstat(uart->tx_dma_channel);
+#ifdef CONFIG_BF54x
+ UART_CLEAR_IER(uart, ETBEI);
+#else
ier = UART_GET_IER(uart);
ier &= ~ETBEI;
UART_PUT_IER(uart, ier);
- xmit->tail = (xmit->tail+uart->tx_count) &(UART_XMIT_SIZE -1);
- uart->port.icount.tx+=uart->tx_count;
+#endif
+ xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
+ uart->port.icount.tx += uart->tx_count;
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uart->port);
- if (uart_circ_empty(xmit))
- bfin_serial_stop_tx(&uart->port);
- uart->tx_done = 1;
+ bfin_serial_dma_tx_chars(uart);
}
spin_unlock(&uart->port.lock);
struct bfin_serial_port *uart = dev_id;
unsigned short irqstat;
- uart->rx_dma_nrows++;
- if (uart->rx_dma_nrows == DMA_RX_YCOUNT) {
- uart->rx_dma_nrows = 0;
- uart->rx_dma_buf.tail = DMA_RX_XCOUNT*DMA_RX_YCOUNT;
- bfin_serial_dma_rx_chars(uart);
- uart->rx_dma_buf.head = uart->rx_dma_buf.tail = 0;
- }
spin_lock(&uart->port.lock);
irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
clear_dma_irqstat(uart->rx_dma_channel);
-
spin_unlock(&uart->port.lock);
+
+ mod_timer(&(uart->rx_dma_timer), jiffies);
+
return IRQ_HANDLED;
}
#endif
if (uart->cts_pin < 0)
return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+# ifdef BF54x
+ if (UART_GET_MSR(uart) & CTS)
+# else
if (gpio_get_value(uart->cts_pin))
+# endif
return TIOCM_DSR | TIOCM_CAR;
else
#endif
return;
if (mctrl & TIOCM_RTS)
+# ifdef BF54x
+ UART_PUT_MCR(uart, UART_GET_MCR(uart) & ~MRTS);
+# else
gpio_set_value(uart->rts_pin, 0);
+# endif
else
+# ifdef BF54x
+ UART_PUT_MCR(uart, UART_GET_MCR(uart) | MRTS);
+# else
gpio_set_value(uart->rts_pin, 1);
+# endif
#endif
}
{
#ifdef CONFIG_SERIAL_BFIN_CTSRTS
unsigned int status;
-# ifdef CONFIG_SERIAL_BFIN_DMA
struct uart_info *info = uart->port.info;
struct tty_struct *tty = info->tty;
status = bfin_serial_get_mctrl(&uart->port);
+ uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
if (!(status & TIOCM_CTS)) {
tty->hw_stopped = 1;
+ schedule_work(&uart->cts_workqueue);
} else {
tty->hw_stopped = 0;
}
-# else
- status = bfin_serial_get_mctrl(&uart->port);
- uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
- if (!(status & TIOCM_CTS))
- schedule_work(&uart->cts_workqueue);
-# endif
#endif
}
set_dma_config(uart->rx_dma_channel,
set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
INTR_ON_ROW, DIMENSION_2D,
- DATA_SIZE_8));
+ DATA_SIZE_8,
+ DMA_SYNC_RESTART));
set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT);
set_dma_x_modify(uart->rx_dma_channel, 1);
set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT);
uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
add_timer(&(uart->rx_dma_timer));
#else
+ if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
+ "BFIN_UART_RX", uart)) {
# ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT && request_irq
-# else
- if (request_irq
+ if (uart->port.line != CONFIG_KGDB_UART_PORT) {
# endif
- (uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
- "BFIN_UART_RX", uart)) {
printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
return -EBUSY;
+# ifdef CONFIG_KGDB_UART
+ }
+# endif
}
+
if (request_irq
(uart->port.irq+1, bfin_serial_tx_int, IRQF_DISABLED,
"BFIN_UART_TX", uart)) {
return -EBUSY;
}
#endif
+#ifdef CONFIG_BF54x
+ UART_SET_IER(uart, ERBFI);
+#else
UART_PUT_IER(uart, UART_GET_IER(uart) | ERBFI);
+#endif
return 0;
}
disable_dma(uart->rx_dma_channel);
free_dma(uart->rx_dma_channel);
del_timer(&(uart->rx_dma_timer));
+ dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0);
#else
#ifdef CONFIG_KGDB_UART
if (uart->port.line != CONFIG_KGDB_UART_PORT)
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
unsigned long flags;
unsigned int baud, quot;
- unsigned short val, ier, lsr, lcr = 0;
+ unsigned short val, ier, lcr = 0;
switch (termios->c_cflag & CSIZE) {
case CS8:
quot = uart_get_divisor(port, baud);
spin_lock_irqsave(&uart->port.lock, flags);
- do {
- lsr = UART_GET_LSR(uart);
- } while (!(lsr & TEMT));
+ UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
/* Disable UART */
ier = UART_GET_IER(uart);
+#ifdef CONFIG_BF54x
+ UART_CLEAR_IER(uart, 0xF);
+#else
UART_PUT_IER(uart, 0);
+#endif
+#ifndef CONFIG_BF54x
/* Set DLAB in LCR to Access DLL and DLH */
val = UART_GET_LCR(uart);
val |= DLAB;
UART_PUT_LCR(uart, val);
SSYNC();
+#endif
UART_PUT_DLL(uart, quot & 0xFF);
SSYNC();
UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
SSYNC();
+#ifndef CONFIG_BF54x
/* Clear DLAB in LCR to Access THR RBR IER */
val = UART_GET_LCR(uart);
val &= ~DLAB;
UART_PUT_LCR(uart, val);
SSYNC();
+#endif
UART_PUT_LCR(uart, lcr);
/* Enable UART */
+#ifdef CONFIG_BF54x
+ UART_SET_IER(uart, ier);
+#else
UART_PUT_IER(uart, ier);
+#endif
val = UART_GET_GCTL(uart);
val |= UCEN;
return 0;
}
+/*
+ * Enable the IrDA function if tty->ldisc.num is N_IRDA.
+ * In other cases, disable IrDA function.
+ */
+static void bfin_set_ldisc(struct tty_struct *tty)
+{
+ int line = tty->index;
+ unsigned short val;
+
+ if (line >= tty->driver->num)
+ return;
+
+ switch (tty->ldisc.num) {
+ case N_IRDA:
+ val = UART_GET_GCTL(&bfin_serial_ports[line]);
+ val |= (IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ break;
+ default:
+ val = UART_GET_GCTL(&bfin_serial_ports[line]);
+ val &= ~(IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ }
+}
+
static struct uart_ops bfin_serial_pops = {
.tx_empty = bfin_serial_tx_empty,
.set_mctrl = bfin_serial_set_mctrl,
bfin_serial_ports[i].rx_dma_channel =
bfin_serial_resource[i].uart_rx_dma_channel;
init_timer(&(bfin_serial_ports[i].rx_dma_timer));
-#else
- INIT_WORK(&bfin_serial_ports[i].cts_workqueue, bfin_serial_do_work);
#endif
#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ INIT_WORK(&bfin_serial_ports[i].cts_workqueue, bfin_serial_do_work);
bfin_serial_ports[i].cts_pin =
bfin_serial_resource[i].uart_cts_pin;
bfin_serial_ports[i].rts_pin =
bfin_serial_resource[i].uart_rts_pin;
#endif
bfin_serial_hw_init(&bfin_serial_ports[i]);
-
}
-}
-
-#ifdef CONFIG_SERIAL_BFIN_CONSOLE
-static void bfin_serial_console_putchar(struct uart_port *port, int ch)
-{
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- while (!(UART_GET_LSR(uart)))
- barrier();
- UART_PUT_CHAR(uart, ch);
- SSYNC();
-}
-
-/*
- * Interrupts are disabled on entering
- */
-static void
-bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
-{
- struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
- int flags = 0;
-
- spin_lock_irqsave(&uart->port.lock, flags);
- uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
- spin_unlock_irqrestore(&uart->port.lock, flags);
}
+#ifdef CONFIG_SERIAL_BFIN_CONSOLE
/*
* If the port was already initialised (eg, by a boot loader),
* try to determine the current setup.
case 2: *bits = 7; break;
case 3: *bits = 8; break;
}
+#ifndef CONFIG_BF54x
/* Set DLAB in LCR to Access DLL and DLH */
val = UART_GET_LCR(uart);
val |= DLAB;
UART_PUT_LCR(uart, val);
+#endif
dll = UART_GET_DLL(uart);
dlh = UART_GET_DLH(uart);
+#ifndef CONFIG_BF54x
/* Clear DLAB in LCR to Access THR RBR IER */
val = UART_GET_LCR(uart);
val &= ~DLAB;
UART_PUT_LCR(uart, val);
+#endif
*baud = get_sclk() / (16*(dll | dlh << 8));
}
pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __FUNCTION__, *baud, *parity, *bits);
}
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
+static struct uart_driver bfin_serial_reg;
static int __init
bfin_serial_console_setup(struct console *co, char *options)
{
struct bfin_serial_port *uart;
+# ifdef CONFIG_SERIAL_BFIN_CONSOLE
int baud = 57600;
int bits = 8;
int parity = 'n';
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+# ifdef CONFIG_SERIAL_BFIN_CTSRTS
int flow = 'r';
-#else
+# else
int flow = 'n';
-#endif
+# endif
+# endif
/*
* Check whether an invalid uart number has been specified, and
co->index = 0;
uart = &bfin_serial_ports[co->index];
+# ifdef CONFIG_SERIAL_BFIN_CONSOLE
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
bfin_serial_console_get_options(uart, &baud, &parity, &bits);
return uart_set_options(&uart->port, co, baud, parity, bits, flow);
+# else
+ return 0;
+# endif
+}
+#endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
+ defined (CONFIG_EARLY_PRINTK) */
+
+#ifdef CONFIG_SERIAL_BFIN_CONSOLE
+static void bfin_serial_console_putchar(struct uart_port *port, int ch)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ while (!(UART_GET_LSR(uart) & THRE))
+ barrier();
+ UART_PUT_CHAR(uart, ch);
+ SSYNC();
+}
+
+/*
+ * Interrupts are disabled on entering
+ */
+static void
+bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
+{
+ struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
+ int flags = 0;
+
+ spin_lock_irqsave(&uart->port.lock, flags);
+ uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
+ spin_unlock_irqrestore(&uart->port.lock, flags);
+
}
-static struct uart_driver bfin_serial_reg;
static struct console bfin_serial_console = {
.name = BFIN_SERIAL_NAME,
.write = bfin_serial_console_write,
#define BFIN_SERIAL_CONSOLE &bfin_serial_console
#else
#define BFIN_SERIAL_CONSOLE NULL
-#endif
+#endif /* CONFIG_SERIAL_BFIN_CONSOLE */
+
+
+#ifdef CONFIG_EARLY_PRINTK
+static __init void early_serial_putc(struct uart_port *port, int ch)
+{
+ unsigned timeout = 0xffff;
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+ while ((!(UART_GET_LSR(uart) & THRE)) && --timeout)
+ cpu_relax();
+ UART_PUT_CHAR(uart, ch);
+}
+
+static __init void early_serial_write(struct console *con, const char *s,
+ unsigned int n)
+{
+ struct bfin_serial_port *uart = &bfin_serial_ports[con->index];
+ unsigned int i;
+
+ for (i = 0; i < n; i++, s++) {
+ if (*s == '\n')
+ early_serial_putc(&uart->port, '\r');
+ early_serial_putc(&uart->port, *s);
+ }
+}
+
+static struct __init console bfin_early_serial_console = {
+ .name = "early_BFuart",
+ .write = early_serial_write,
+ .device = uart_console_device,
+ .flags = CON_PRINTBUFFER,
+ .setup = bfin_serial_console_setup,
+ .index = -1,
+ .data = &bfin_serial_reg,
+};
+
+struct console __init *bfin_earlyserial_init(unsigned int port,
+ unsigned int cflag)
+{
+ struct bfin_serial_port *uart;
+ struct ktermios t;
+
+ if (port == -1 || port >= nr_ports)
+ port = 0;
+ bfin_serial_init_ports();
+ bfin_early_serial_console.index = port;
+ uart = &bfin_serial_ports[port];
+ t.c_cflag = cflag;
+ t.c_iflag = 0;
+ t.c_oflag = 0;
+ t.c_lflag = ICANON;
+ t.c_line = port;
+ bfin_serial_set_termios(&uart->port, &t, &t);
+ return &bfin_early_serial_console;
+}
+
+#endif /* CONFIG_SERIAL_BFIN_CONSOLE */
static struct uart_driver bfin_serial_reg = {
.owner = THIS_MODULE,
.dev_name = BFIN_SERIAL_NAME,
.major = BFIN_SERIAL_MAJOR,
.minor = BFIN_SERIAL_MINOR,
- .nr = NR_PORTS,
+ .nr = BFIN_UART_NR_PORTS,
.cons = BFIN_SERIAL_CONSOLE,
};
.resume = bfin_serial_resume,
.driver = {
.name = "bfin-uart",
+ .owner = THIS_MODULE,
},
};
int ret;
#ifdef CONFIG_KGDB_UART
struct bfin_serial_port *uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
- struct termios t;
+ struct ktermios t;
#endif
pr_info("Serial: Blackfin serial driver\n");
ret = uart_register_driver(&bfin_serial_reg);
if (ret == 0) {
+ bfin_serial_reg.tty_driver->set_ldisc = bfin_set_ldisc;
ret = platform_driver_register(&bfin_serial_driver);
if (ret) {
pr_debug("uart register failed\n");
}
#ifdef CONFIG_KGDB_UART
if (uart->port.cons->index != CONFIG_KGDB_UART_PORT) {
- request_irq(uart->port.irq, bfin_serial_int,
+ request_irq(uart->port.irq, bfin_serial_rx_int,
IRQF_DISABLED, "BFIN_UART_RX", uart);
pr_info("Request irq for kgdb uart port\n");
+#ifdef CONFIG_BF54x
+ UART_SET_IER(uart, ERBFI);
+#else
UART_PUT_IER(uart, UART_GET_IER(uart) | ERBFI);
- __builtin_bfin_ssync();
+#endif
+ SSYNC();
t.c_cflag = CS8|B57600;
t.c_iflag = 0;
t.c_oflag = 0;
MODULE_DESCRIPTION("Blackfin generic serial port driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR);
+MODULE_ALIAS("platform:bfin-uart");