/*
* Blackfin On-Chip Serial Driver
*
- * Copyright 2006-2007 Analog Devices Inc.
+ * Copyright 2006-2008 Analog Devices Inc.
*
* Enter bugs at http://blackfin.uclinux.org/
*
#include <linux/tty_flip.h>
#include <linux/serial_core.h>
-#ifdef CONFIG_KGDB_UART
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
#include <linux/kgdb.h>
#include <asm/irq_regs.h>
#endif
#include <asm/gpio.h>
-#include <asm/mach/bfin_serial_5xx.h>
+#include <mach/bfin_serial_5xx.h>
#ifdef CONFIG_SERIAL_BFIN_DMA
#include <linux/dma-mapping.h>
#include <asm/cacheflush.h>
#endif
+#ifdef CONFIG_SERIAL_BFIN_MODULE
+# undef CONFIG_EARLY_PRINTK
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_MODULE
+# undef CONFIG_EARLY_PRINTK
+#endif
+
/* UART name and device definitions */
#define BFIN_SERIAL_NAME "ttyBF"
#define BFIN_SERIAL_MAJOR 204
#define BFIN_SERIAL_MINOR 64
+static struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
+static int nr_active_ports = ARRAY_SIZE(bfin_serial_resource);
+
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+
+# ifndef CONFIG_SERIAL_BFIN_PIO
+# error KGDB only support UART in PIO mode.
+# endif
+
+static int kgdboc_port_line;
+static int kgdboc_break_enabled;
+#endif
/*
* Setup for console. Argument comes from the menuconfig
*/
#define DMA_RX_XCOUNT 512
#define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT)
-#define DMA_RX_FLUSH_JIFFIES 5
+#define DMA_RX_FLUSH_JIFFIES (HZ / 50)
#ifdef CONFIG_SERIAL_BFIN_DMA
static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
#else
-static void bfin_serial_do_work(struct work_struct *work);
static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
#endif
-static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
+static void bfin_serial_reset_irda(struct uart_port *port);
+
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->cts_pin < 0)
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+ /* CTS PIN is negative assertive. */
+ if (UART_GET_CTS(uart))
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+ else
+ return TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->rts_pin < 0)
+ return;
+
+ /* RTS PIN is negative assertive. */
+ if (mctrl & TIOCM_RTS)
+ UART_ENABLE_RTS(uart);
+ else
+ UART_DISABLE_RTS(uart);
+}
+
+/*
+ * Handle any change of modem status signal.
+ */
+static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
+{
+ struct bfin_serial_port *uart = dev_id;
+ unsigned int status;
+
+ status = bfin_serial_get_mctrl(&uart->port);
+ uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ uart->scts = 1;
+ UART_CLEAR_SCTS(uart);
+ UART_CLEAR_IER(uart, EDSSI);
+#endif
+
+ return IRQ_HANDLED;
+}
+#else
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+#endif
/*
* interrupts are disabled on entry
static void bfin_serial_stop_tx(struct uart_port *port)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-#if !defined(CONFIG_BF54x) && !defined(CONFIG_SERIAL_BFIN_DMA)
- unsigned short ier;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+ struct circ_buf *xmit = &uart->port.state->xmit;
#endif
while (!(UART_GET_LSR(uart) & TEMT))
- continue;
+ cpu_relax();
#ifdef CONFIG_SERIAL_BFIN_DMA
disable_dma(uart->tx_dma_channel);
+ xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
+ uart->port.icount.tx += uart->tx_count;
+ uart->tx_count = 0;
+ uart->tx_done = 1;
#else
#ifdef CONFIG_BF54x
/* Clear TFI bit */
UART_PUT_LSR(uart, TFI);
- UART_CLEAR_IER(uart, ETBEI);
-#else
- ier = UART_GET_IER(uart);
- ier &= ~ETBEI;
- UART_PUT_IER(uart, ier);
#endif
+ UART_CLEAR_IER(uart, ETBEI);
#endif
}
static void bfin_serial_start_tx(struct uart_port *port)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ struct tty_struct *tty = uart->port.state->port.tty;
+
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
+
+ /*
+ * To avoid losting RX interrupt, we reset IR function
+ * before sending data.
+ */
+ if (tty->termios->c_line == N_IRDA)
+ bfin_serial_reset_irda(port);
#ifdef CONFIG_SERIAL_BFIN_DMA
- bfin_serial_dma_tx_chars(uart);
+ if (uart->tx_done)
+ bfin_serial_dma_tx_chars(uart);
#else
-#ifdef CONFIG_BF54x
UART_SET_IER(uart, ETBEI);
-#else
- unsigned short ier;
- ier = UART_GET_IER(uart);
- ier |= ETBEI;
- UART_PUT_IER(uart, ier);
-#endif
bfin_serial_tx_chars(uart);
#endif
}
static void bfin_serial_stop_rx(struct uart_port *port)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-#ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT) {
-#endif
-#ifdef CONFIG_BF54x
- UART_CLEAR_IER(uart, ERBFI);
-#else
- unsigned short ier;
- ier = UART_GET_IER(uart);
- ier &= ~ERBFI;
- UART_PUT_IER(uart, ier);
-#endif
-#ifdef CONFIG_KGDB_UART
- }
-#endif
+ UART_CLEAR_IER(uart, ERBFI);
}
/*
{
}
-#ifdef CONFIG_KGDB_UART
-static int kgdb_entry_state;
-
-void kgdb_put_debug_char(int chr)
-{
- struct bfin_serial_port *uart;
-
- if (CONFIG_KGDB_UART_PORT<0 || CONFIG_KGDB_UART_PORT>=NR_PORTS)
- uart = &bfin_serial_ports[0];
- else
- uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
-
- while (!(UART_GET_LSR(uart) & THRE)) {
- SSYNC();
- }
-
-#ifndef CONFIG_BF54x
- UART_PUT_LCR(uart, UART_GET_LCR(uart)&(~DLAB));
- SSYNC();
-#endif
- UART_PUT_CHAR(uart, (unsigned char)chr);
- SSYNC();
-}
-
-int kgdb_get_debug_char(void)
-{
- struct bfin_serial_port *uart;
- unsigned char chr;
- if (CONFIG_KGDB_UART_PORT<0 || CONFIG_KGDB_UART_PORT>=NR_PORTS)
- uart = &bfin_serial_ports[0];
- else
- uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
-
- while(!(UART_GET_LSR(uart) & DR)) {
- SSYNC();
- }
-#ifndef CONFIG_BF54x
- UART_PUT_LCR(uart, UART_GET_LCR(uart)&(~DLAB));
- SSYNC();
-#endif
- chr = UART_GET_CHAR(uart);
- SSYNC();
-
- return chr;
-}
-#endif
-
-#if ANOMALY_05000230 && defined(CONFIG_SERIAL_BFIN_PIO)
+#if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO)
# define UART_GET_ANOMALY_THRESHOLD(uart) ((uart)->anomaly_threshold)
# define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v))
#else
#ifdef CONFIG_SERIAL_BFIN_PIO
static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
{
- struct tty_struct *tty = uart->port.info->tty;
+ struct tty_struct *tty = NULL;
unsigned int status, ch, flg;
static struct timeval anomaly_start = { .tv_sec = 0 };
-#ifdef CONFIG_KGDB_UART
- struct pt_regs *regs = get_irq_regs();
-#endif
status = UART_GET_LSR(uart);
UART_CLEAR_LSR(uart);
ch = UART_GET_CHAR(uart);
uart->port.icount.rx++;
-#ifdef CONFIG_KGDB_UART
- if (uart->port.line == CONFIG_KGDB_UART_PORT) {
- if (uart->port.cons->index == CONFIG_KGDB_UART_PORT && ch == 0x1) { /* Ctrl + A */
- kgdb_breakkey_pressed(regs);
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+ if (kgdb_connected && kgdboc_port_line == uart->port.line)
+ if (ch == 0x3) {/* Ctrl + C */
+ kgdb_breakpoint();
return;
- } else if (kgdb_entry_state == 0 && ch == '$') {/* connection from KGDB */
- kgdb_entry_state = 1;
- } else if (kgdb_entry_state == 1 && ch == 'q') {
- kgdb_entry_state = 0;
- kgdb_breakkey_pressed(regs);
- return;
- } else if (ch == 0x3) {/* Ctrl + C */
- kgdb_entry_state = 0;
- kgdb_breakkey_pressed(regs);
- return;
- } else {
- kgdb_entry_state = 0;
}
- }
+
+ if (!uart->port.state || !uart->port.state->port.tty)
+ return;
#endif
+ tty = uart->port.state->port.tty;
- if (ANOMALY_05000230) {
+ if (ANOMALY_05000363) {
/* The BF533 (and BF561) family of processors have a nice anomaly
* where they continuously generate characters for a "single" break.
* We have to basically ignore this flood until the "next" valid
* timeout was picked as it must absolutely be larger than 1
* character time +/- some percent. So 1.5 sounds good. All other
* Blackfin families operate properly. Woo.
- * Note: While Anomaly 05000230 does not directly address this,
- * the changes that went in for it also fixed this issue.
- * That anomaly was fixed in 0.5+ silicon. I like bunnies.
*/
if (anomaly_start.tv_sec) {
struct timeval curr;
return;
known_good_char:
+ status &= ~BI;
anomaly_start.tv_sec = 0;
}
}
if (status & BI) {
- if (ANOMALY_05000230)
+ if (ANOMALY_05000363)
if (bfin_revid() < 5)
do_gettimeofday(&anomaly_start);
uart->port.icount.brk++;
static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
{
- struct circ_buf *xmit = &uart->port.info->xmit;
+ struct circ_buf *xmit = &uart->port.state->xmit;
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
+#ifdef CONFIG_BF54x
+ /* Clear TFI bit */
+ UART_PUT_LSR(uart, TFI);
+#endif
+ /* Anomaly notes:
+ * 05000215 - we always clear ETBEI within last UART TX
+ * interrupt to end a string. It is always set
+ * when start a new tx.
+ */
+ UART_CLEAR_IER(uart, ETBEI);
+ return;
+ }
if (uart->port.x_char) {
UART_PUT_CHAR(uart, uart->port.x_char);
uart->port.icount.tx++;
uart->port.x_char = 0;
}
- /*
- * Check the modem control lines before
- * transmitting anything.
- */
- bfin_serial_mctrl_check(uart);
-
- if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
- bfin_serial_stop_tx(&uart->port);
- return;
- }
while ((UART_GET_LSR(uart) & THRE) && xmit->tail != xmit->head) {
UART_PUT_CHAR(uart, xmit->buf[xmit->tail]);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uart->port);
-
- if (uart_circ_empty(xmit))
- bfin_serial_stop_tx(&uart->port);
}
static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id)
{
struct bfin_serial_port *uart = dev_id;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
spin_lock(&uart->port.lock);
if (UART_GET_LSR(uart) & THRE)
bfin_serial_tx_chars(uart);
return IRQ_HANDLED;
}
-
-
-static void bfin_serial_do_work(struct work_struct *work)
-{
- struct bfin_serial_port *uart = container_of(work, struct bfin_serial_port, cts_workqueue);
-
- bfin_serial_mctrl_check(uart);
-}
#endif
#ifdef CONFIG_SERIAL_BFIN_DMA
static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
{
- struct circ_buf *xmit = &uart->port.info->xmit;
- unsigned short ier;
- int flags = 0;
+ struct circ_buf *xmit = &uart->port.state->xmit;
- if (!uart->tx_done)
- return;
uart->tx_done = 0;
if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
- bfin_serial_stop_tx(&uart->port);
+ uart->tx_count = 0;
uart->tx_done = 1;
return;
}
uart->port.x_char = 0;
}
- /*
- * Check the modem control lines before
- * transmitting anything.
- */
- bfin_serial_mctrl_check(uart);
-
- spin_lock_irqsave(&uart->port.lock, flags);
uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
uart->tx_count = UART_XMIT_SIZE - xmit->tail;
set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
set_dma_x_modify(uart->tx_dma_channel, 1);
+ SSYNC();
enable_dma(uart->tx_dma_channel);
- xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
- uart->port.icount.tx += uart->tx_count;
-
-#ifdef CONFIG_BF54x
UART_SET_IER(uart, ETBEI);
-#else
- ier = UART_GET_IER(uart);
- ier |= ETBEI;
- UART_PUT_IER(uart, ier);
-#endif
- spin_unlock_irqrestore(&uart->port.lock, flags);
}
static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
{
- struct tty_struct *tty = uart->port.info->tty;
+ struct tty_struct *tty = uart->port.state->port.tty;
int i, flg, status;
status = UART_GET_LSR(uart);
UART_CLEAR_LSR(uart);
- uart->port.icount.rx += CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail, UART_XMIT_SIZE);;
+ uart->port.icount.rx +=
+ CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail,
+ UART_XMIT_SIZE);
if (status & BI) {
uart->port.icount.brk++;
else
flg = TTY_NORMAL;
- for (i = uart->rx_dma_buf.head; i < uart->rx_dma_buf.tail; i++) {
- if (uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
- goto dma_ignore_char;
- uart_insert_char(&uart->port, status, OE, uart->rx_dma_buf.buf[i], flg);
+ for (i = uart->rx_dma_buf.tail; ; i++) {
+ if (i >= UART_XMIT_SIZE)
+ i = 0;
+ if (i == uart->rx_dma_buf.head)
+ break;
+ if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
+ uart_insert_char(&uart->port, status, OE,
+ uart->rx_dma_buf.buf[i], flg);
}
dma_ignore_char:
void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
{
int x_pos, pos;
- int flags = 0;
- spin_lock_irqsave(&uart->port.lock, flags);
- x_pos = DMA_RX_XCOUNT - get_dma_curr_xcount(uart->rx_dma_channel);
+ dma_disable_irq(uart->rx_dma_channel);
+ spin_lock_bh(&uart->port.lock);
+
+ /* 2D DMA RX buffer ring is used. Because curr_y_count and
+ * curr_x_count can't be read as an atomic operation,
+ * curr_y_count should be read before curr_x_count. When
+ * curr_x_count is read, curr_y_count may already indicate
+ * next buffer line. But, the position calculated here is
+ * still indicate the old line. The wrong position data may
+ * be smaller than current buffer tail, which cause garbages
+ * are received if it is not prohibit.
+ */
+ uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
+ x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
+ uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
+ if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
+ uart->rx_dma_nrows = 0;
+ x_pos = DMA_RX_XCOUNT - x_pos;
if (x_pos == DMA_RX_XCOUNT)
x_pos = 0;
pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
-
- if (pos>uart->rx_dma_buf.tail) {
- uart->rx_dma_buf.tail = pos;
+ /* Ignore receiving data if new position is in the same line of
+ * current buffer tail and small.
+ */
+ if (pos > uart->rx_dma_buf.tail ||
+ uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
+ uart->rx_dma_buf.head = pos;
bfin_serial_dma_rx_chars(uart);
- uart->rx_dma_buf.head = uart->rx_dma_buf.tail;
+ uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
}
- spin_unlock_irqrestore(&uart->port.lock, flags);
- uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
- add_timer(&(uart->rx_dma_timer));
+
+ spin_unlock_bh(&uart->port.lock);
+ dma_enable_irq(uart->rx_dma_channel);
+
+ mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
}
static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
{
struct bfin_serial_port *uart = dev_id;
- struct circ_buf *xmit = &uart->port.info->xmit;
- unsigned short ier;
+ struct circ_buf *xmit = &uart->port.state->xmit;
+
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && !(bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
spin_lock(&uart->port.lock);
if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
- clear_dma_irqstat(uart->tx_dma_channel);
disable_dma(uart->tx_dma_channel);
-#ifdef CONFIG_BF54x
+ clear_dma_irqstat(uart->tx_dma_channel);
+ /* Anomaly notes:
+ * 05000215 - we always clear ETBEI within last UART TX
+ * interrupt to end a string. It is always set
+ * when start a new tx.
+ */
UART_CLEAR_IER(uart, ETBEI);
-#else
- ier = UART_GET_IER(uart);
- ier &= ~ETBEI;
- UART_PUT_IER(uart, ier);
-#endif
+ xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
+ uart->port.icount.tx += uart->tx_count;
+
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uart->port);
- uart->tx_done = 1;
-
bfin_serial_dma_tx_chars(uart);
}
{
struct bfin_serial_port *uart = dev_id;
unsigned short irqstat;
+ int x_pos, pos;
- uart->rx_dma_nrows++;
- if (uart->rx_dma_nrows == DMA_RX_YCOUNT) {
- uart->rx_dma_nrows = 0;
- uart->rx_dma_buf.tail = DMA_RX_XCOUNT*DMA_RX_YCOUNT;
- bfin_serial_dma_rx_chars(uart);
- uart->rx_dma_buf.head = uart->rx_dma_buf.tail = 0;
- }
spin_lock(&uart->port.lock);
irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
clear_dma_irqstat(uart->rx_dma_channel);
+ uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
+ x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
+ uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
+ if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
+ uart->rx_dma_nrows = 0;
+
+ pos = uart->rx_dma_nrows * DMA_RX_XCOUNT;
+ if (pos > uart->rx_dma_buf.tail ||
+ uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
+ uart->rx_dma_buf.head = pos;
+ bfin_serial_dma_rx_chars(uart);
+ uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
+ }
+
spin_unlock(&uart->port.lock);
+
return IRQ_HANDLED;
}
#endif
return 0;
}
-static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->cts_pin < 0)
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-
- if (gpio_get_value(uart->cts_pin))
- return TIOCM_DSR | TIOCM_CAR;
- else
-#endif
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-}
-
-static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->rts_pin < 0)
- return;
-
- if (mctrl & TIOCM_RTS)
- gpio_set_value(uart->rts_pin, 0);
- else
- gpio_set_value(uart->rts_pin, 1);
-#endif
-}
-
-/*
- * Handle any change of modem status signal since we were last called.
- */
-static void bfin_serial_mctrl_check(struct bfin_serial_port *uart)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- unsigned int status;
-# ifdef CONFIG_SERIAL_BFIN_DMA
- struct uart_info *info = uart->port.info;
- struct tty_struct *tty = info->tty;
-
- status = bfin_serial_get_mctrl(&uart->port);
- if (!(status & TIOCM_CTS)) {
- tty->hw_stopped = 1;
- } else {
- tty->hw_stopped = 0;
- }
-# else
- status = bfin_serial_get_mctrl(&uart->port);
- uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
- if (!(status & TIOCM_CTS))
- schedule_work(&uart->cts_workqueue);
-# endif
-#endif
-}
-
-/*
- * Interrupts are always disabled.
- */
static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
add_timer(&(uart->rx_dma_timer));
#else
+# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+ if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled)
+ kgdboc_break_enabled = 0;
+ else {
+# endif
if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
"BFIN_UART_RX", uart)) {
-# ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT) {
-# endif
printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
return -EBUSY;
-# ifdef CONFIG_KGDB_UART
- }
-# endif
}
-
if (request_irq
(uart->port.irq+1, bfin_serial_tx_int, IRQF_DISABLED,
"BFIN_UART_TX", uart)) {
free_irq(uart->port.irq, uart);
return -EBUSY;
}
+
+# ifdef CONFIG_BF54x
+ {
+ unsigned uart_dma_ch_rx, uart_dma_ch_tx;
+
+ switch (uart->port.irq) {
+ case IRQ_UART3_RX:
+ uart_dma_ch_rx = CH_UART3_RX;
+ uart_dma_ch_tx = CH_UART3_TX;
+ break;
+ case IRQ_UART2_RX:
+ uart_dma_ch_rx = CH_UART2_RX;
+ uart_dma_ch_tx = CH_UART2_TX;
+ break;
+ default:
+ uart_dma_ch_rx = uart_dma_ch_tx = 0;
+ break;
+ };
+
+ if (uart_dma_ch_rx &&
+ request_dma(uart_dma_ch_rx, "BFIN_UART_RX") < 0) {
+ printk(KERN_NOTICE"Fail to attach UART interrupt\n");
+ free_irq(uart->port.irq, uart);
+ free_irq(uart->port.irq + 1, uart);
+ return -EBUSY;
+ }
+ if (uart_dma_ch_tx &&
+ request_dma(uart_dma_ch_tx, "BFIN_UART_TX") < 0) {
+ printk(KERN_NOTICE "Fail to attach UART interrupt\n");
+ free_dma(uart_dma_ch_rx);
+ free_irq(uart->port.irq, uart);
+ free_irq(uart->port.irq + 1, uart);
+ return -EBUSY;
+ }
+ }
+# endif
+# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+ }
+# endif
#endif
-#ifdef CONFIG_BF54x
- UART_SET_IER(uart, ERBFI);
-#else
- UART_PUT_IER(uart, UART_GET_IER(uart) | ERBFI);
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ if (uart->cts_pin >= 0) {
+ if (request_irq(gpio_to_irq(uart->cts_pin),
+ bfin_serial_mctrl_cts_int,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
+ IRQF_DISABLED, "BFIN_UART_CTS", uart)) {
+ uart->cts_pin = -1;
+ pr_info("Unable to attach BlackFin UART CTS interrupt.\
+ So, disable it.\n");
+ }
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->rts_pin, 0);
+ }
+#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (request_irq(uart->status_irq,
+ bfin_serial_mctrl_cts_int,
+ IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
+ pr_info("Unable to attach BlackFin UART Modem \
+ Status interrupt.\n");
+ }
+
+ if (uart->cts_pin >= 0) {
+ gpio_request(uart->cts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->cts_pin, 1);
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->rts_pin, 0);
+ }
+
+ /* CTS RTS PINs are negative assertive. */
+ UART_PUT_MCR(uart, ACTS);
+ UART_SET_IER(uart, EDSSI);
#endif
+
+ UART_SET_IER(uart, ERBFI);
return 0;
}
del_timer(&(uart->rx_dma_timer));
dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0);
#else
-#ifdef CONFIG_KGDB_UART
- if (uart->port.line != CONFIG_KGDB_UART_PORT)
+#ifdef CONFIG_BF54x
+ switch (uart->port.irq) {
+ case IRQ_UART3_RX:
+ free_dma(CH_UART3_RX);
+ free_dma(CH_UART3_TX);
+ break;
+ case IRQ_UART2_RX:
+ free_dma(CH_UART2_RX);
+ free_dma(CH_UART2_TX);
+ break;
+ default:
+ break;
+ };
#endif
free_irq(uart->port.irq, uart);
free_irq(uart->port.irq+1, uart);
#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ if (uart->cts_pin >= 0)
+ free_irq(gpio_to_irq(uart->cts_pin), uart);
+ if (uart->rts_pin >= 0)
+ gpio_free(uart->rts_pin);
+#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->cts_pin >= 0)
+ gpio_free(uart->cts_pin);
+ if (uart->rts_pin >= 0)
+ gpio_free(uart->rts_pin);
+ if (UART_GET_IER(uart) && EDSSI)
+ free_irq(uart->status_irq, uart);
+#endif
}
static void
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
unsigned long flags;
unsigned int baud, quot;
- unsigned short val, ier, lsr, lcr = 0;
+ unsigned short val, ier, lcr = 0;
switch (termios->c_cflag & CSIZE) {
case CS8:
break;
default:
printk(KERN_ERR "%s: word lengh not supported\n",
- __FUNCTION__);
+ __func__);
}
- if (termios->c_cflag & CSTOPB)
- lcr |= STB;
+ /* Anomaly notes:
+ * 05000231 - STOP bit is always set to 1 whatever the user is set.
+ */
+ if (termios->c_cflag & CSTOPB) {
+ if (ANOMALY_05000231)
+ printk(KERN_WARNING "STOP bits other than 1 is not "
+ "supported in case of anomaly 05000231.\n");
+ else
+ lcr |= STB;
+ }
if (termios->c_cflag & PARENB)
lcr |= PEN;
if (!(termios->c_cflag & PARODD))
}
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
- quot = uart_get_divisor(port, baud);
+ quot = uart_get_divisor(port, baud) - ANOMALY_05000230;
spin_lock_irqsave(&uart->port.lock, flags);
UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
- do {
- lsr = UART_GET_LSR(uart);
- } while (!(lsr & TEMT));
-
/* Disable UART */
ier = UART_GET_IER(uart);
-#ifdef CONFIG_BF54x
- UART_CLEAR_IER(uart, 0xF);
-#else
- UART_PUT_IER(uart, 0);
-#endif
+ UART_DISABLE_INTS(uart);
-#ifndef CONFIG_BF54x
/* Set DLAB in LCR to Access DLL and DLH */
- val = UART_GET_LCR(uart);
- val |= DLAB;
- UART_PUT_LCR(uart, val);
- SSYNC();
-#endif
+ UART_SET_DLAB(uart);
UART_PUT_DLL(uart, quot & 0xFF);
- SSYNC();
UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
SSYNC();
-#ifndef CONFIG_BF54x
/* Clear DLAB in LCR to Access THR RBR IER */
- val = UART_GET_LCR(uart);
- val &= ~DLAB;
- UART_PUT_LCR(uart, val);
- SSYNC();
-#endif
+ UART_CLEAR_DLAB(uart);
UART_PUT_LCR(uart, lcr);
/* Enable UART */
-#ifdef CONFIG_BF54x
- UART_SET_IER(uart, ier);
-#else
- UART_PUT_IER(uart, ier);
-#endif
+ UART_ENABLE_INTS(uart, ier);
val = UART_GET_GCTL(uart);
val |= UCEN;
UART_PUT_GCTL(uart, val);
+ /* Port speed changed, update the per-port timeout. */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
spin_unlock_irqrestore(&uart->port.lock, flags);
}
return 0;
}
+/*
+ * Enable the IrDA function if tty->ldisc.num is N_IRDA.
+ * In other cases, disable IrDA function.
+ */
+static void bfin_serial_set_ldisc(struct uart_port *port)
+{
+ int line = port->line;
+ unsigned short val;
+
+ if (line >= port->state->port.tty->driver->num)
+ return;
+
+ switch (port->state->port.tty->termios->c_line) {
+ case N_IRDA:
+ val = UART_GET_GCTL(&bfin_serial_ports[line]);
+ val |= (IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ break;
+ default:
+ val = UART_GET_GCTL(&bfin_serial_ports[line]);
+ val &= ~(IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ }
+}
+
+static void bfin_serial_reset_irda(struct uart_port *port)
+{
+ int line = port->line;
+ unsigned short val;
+
+ val = UART_GET_GCTL(&bfin_serial_ports[line]);
+ val &= ~(IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ SSYNC();
+ val |= (IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ SSYNC();
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+/* Anomaly notes:
+ * 05000099 - Because we only use THRE in poll_put and DR in poll_get,
+ * losing other bits of UART_LSR is not a problem here.
+ */
+static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+ while (!(UART_GET_LSR(uart) & THRE))
+ cpu_relax();
+
+ UART_CLEAR_DLAB(uart);
+ UART_PUT_CHAR(uart, (unsigned char)chr);
+}
+
+static int bfin_serial_poll_get_char(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ unsigned char chr;
+
+ while (!(UART_GET_LSR(uart) & DR))
+ cpu_relax();
+
+ UART_CLEAR_DLAB(uart);
+ chr = UART_GET_CHAR(uart);
+
+ return chr;
+}
+#endif
+
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+static void bfin_kgdboc_port_shutdown(struct uart_port *port)
+{
+ if (kgdboc_break_enabled) {
+ kgdboc_break_enabled = 0;
+ bfin_serial_shutdown(port);
+ }
+}
+
+static int bfin_kgdboc_port_startup(struct uart_port *port)
+{
+ kgdboc_port_line = port->line;
+ kgdboc_break_enabled = !bfin_serial_startup(port);
+ return 0;
+}
+#endif
+
static struct uart_ops bfin_serial_pops = {
.tx_empty = bfin_serial_tx_empty,
.set_mctrl = bfin_serial_set_mctrl,
.startup = bfin_serial_startup,
.shutdown = bfin_serial_shutdown,
.set_termios = bfin_serial_set_termios,
+ .set_ldisc = bfin_serial_set_ldisc,
.type = bfin_serial_type,
.release_port = bfin_serial_release_port,
.request_port = bfin_serial_request_port,
.config_port = bfin_serial_config_port,
.verify_port = bfin_serial_verify_port,
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+ defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+ .kgdboc_port_startup = bfin_kgdboc_port_startup,
+ .kgdboc_port_shutdown = bfin_kgdboc_port_shutdown,
+#endif
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_put_char = bfin_serial_poll_put_char,
+ .poll_get_char = bfin_serial_poll_get_char,
+#endif
};
+static void __init bfin_serial_hw_init(void)
+{
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ peripheral_request(P_UART0_TX, DRIVER_NAME);
+ peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ peripheral_request(P_UART1_TX, DRIVER_NAME);
+ peripheral_request(P_UART1_RX, DRIVER_NAME);
+
+# if defined(CONFIG_BFIN_UART1_CTSRTS) && defined(CONFIG_BF54x)
+ peripheral_request(P_UART1_RTS, DRIVER_NAME);
+ peripheral_request(P_UART1_CTS, DRIVER_NAME);
+# endif
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART2
+ peripheral_request(P_UART2_TX, DRIVER_NAME);
+ peripheral_request(P_UART2_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART3
+ peripheral_request(P_UART3_TX, DRIVER_NAME);
+ peripheral_request(P_UART3_RX, DRIVER_NAME);
+
+# if defined(CONFIG_BFIN_UART3_CTSRTS) && defined(CONFIG_BF54x)
+ peripheral_request(P_UART3_RTS, DRIVER_NAME);
+ peripheral_request(P_UART3_CTS, DRIVER_NAME);
+# endif
+#endif
+}
+
static void __init bfin_serial_init_ports(void)
{
static int first = 1;
return;
first = 0;
- for (i = 0; i < nr_ports; i++) {
+ bfin_serial_hw_init();
+
+ for (i = 0; i < nr_active_ports; i++) {
+ spin_lock_init(&bfin_serial_ports[i].port.lock);
bfin_serial_ports[i].port.uartclk = get_sclk();
+ bfin_serial_ports[i].port.fifosize = BFIN_UART_TX_FIFO_SIZE;
bfin_serial_ports[i].port.ops = &bfin_serial_pops;
bfin_serial_ports[i].port.line = i;
bfin_serial_ports[i].port.iotype = UPIO_MEM;
bfin_serial_resource[i].uart_base_addr;
bfin_serial_ports[i].port.irq =
bfin_serial_resource[i].uart_irq;
+ bfin_serial_ports[i].status_irq =
+ bfin_serial_resource[i].uart_status_irq;
bfin_serial_ports[i].port.flags = UPF_BOOT_AUTOCONF;
#ifdef CONFIG_SERIAL_BFIN_DMA
bfin_serial_ports[i].tx_done = 1;
bfin_serial_ports[i].rx_dma_channel =
bfin_serial_resource[i].uart_rx_dma_channel;
init_timer(&(bfin_serial_ports[i].rx_dma_timer));
-#else
- INIT_WORK(&bfin_serial_ports[i].cts_workqueue, bfin_serial_do_work);
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
bfin_serial_ports[i].cts_pin =
bfin_serial_resource[i].uart_cts_pin;
bfin_serial_ports[i].rts_pin =
bfin_serial_resource[i].uart_rts_pin;
#endif
- bfin_serial_hw_init(&bfin_serial_ports[i]);
}
-
}
-#ifdef CONFIG_SERIAL_BFIN_CONSOLE
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
/*
* If the port was already initialised (eg, by a boot loader),
* try to determine the current setup.
status = UART_GET_IER(uart) & (ERBFI | ETBEI);
if (status == (ERBFI | ETBEI)) {
/* ok, the port was enabled */
- unsigned short lcr, val;
- unsigned short dlh, dll;
+ u16 lcr, dlh, dll;
lcr = UART_GET_LCR(uart);
case 2: *bits = 7; break;
case 3: *bits = 8; break;
}
-#ifndef CONFIG_BF54x
/* Set DLAB in LCR to Access DLL and DLH */
- val = UART_GET_LCR(uart);
- val |= DLAB;
- UART_PUT_LCR(uart, val);
-#endif
+ UART_SET_DLAB(uart);
dll = UART_GET_DLL(uart);
dlh = UART_GET_DLH(uart);
-#ifndef CONFIG_BF54x
/* Clear DLAB in LCR to Access THR RBR IER */
- val = UART_GET_LCR(uart);
- val &= ~DLAB;
- UART_PUT_LCR(uart, val);
-#endif
+ UART_CLEAR_DLAB(uart);
*baud = get_sclk() / (16*(dll | dlh << 8));
}
- pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __FUNCTION__, *baud, *parity, *bits);
+ pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits);
}
-#endif
-#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
static struct uart_driver bfin_serial_reg;
static int __init
bfin_serial_console_setup(struct console *co, char *options)
{
struct bfin_serial_port *uart;
-# ifdef CONFIG_SERIAL_BFIN_CONSOLE
int baud = 57600;
int bits = 8;
int parity = 'n';
-# ifdef CONFIG_SERIAL_BFIN_CTSRTS
+# if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
int flow = 'r';
-# else
+# else
int flow = 'n';
-# endif
# endif
/*
* if so, search for the first available port that does have
* console support.
*/
- if (co->index == -1 || co->index >= nr_ports)
+ if (co->index == -1 || co->index >= nr_active_ports)
co->index = 0;
uart = &bfin_serial_ports[co->index];
-# ifdef CONFIG_SERIAL_BFIN_CONSOLE
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
bfin_serial_console_get_options(uart, &baud, &parity, &bits);
return uart_set_options(&uart->port, co, baud, parity, bits, flow);
-# else
- return 0;
-# endif
}
#endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
defined (CONFIG_EARLY_PRINTK) */
bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
{
struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
- int flags = 0;
+ unsigned long flags;
spin_lock_irqsave(&uart->port.lock, flags);
uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
{
bfin_serial_init_ports();
register_console(&bfin_serial_console);
-#ifdef CONFIG_KGDB_UART
- kgdb_entry_state = 0;
- init_kgdb_uart();
-#endif
+
return 0;
}
console_initcall(bfin_serial_rs_console_init);
}
}
-static struct __init console bfin_early_serial_console = {
+/*
+ * This should have a .setup or .early_setup in it, but then things get called
+ * without the command line options, and the baud rate gets messed up - so
+ * don't let the common infrastructure play with things. (see calls to setup
+ * & earlysetup in ./kernel/printk.c:register_console()
+ */
+static struct __initdata console bfin_early_serial_console = {
.name = "early_BFuart",
.write = early_serial_write,
.device = uart_console_device,
.flags = CON_PRINTBUFFER,
- .setup = bfin_serial_console_setup,
.index = -1,
.data = &bfin_serial_reg,
};
struct bfin_serial_port *uart;
struct ktermios t;
- if (port == -1 || port >= nr_ports)
+ if (port == -1 || port >= nr_active_ports)
port = 0;
bfin_serial_init_ports();
bfin_early_serial_console.index = port;
return &bfin_early_serial_console;
}
-#endif /* CONFIG_SERIAL_BFIN_CONSOLE */
+#endif /* CONFIG_EARLY_PRINTK */
static struct uart_driver bfin_serial_reg = {
.owner = THIS_MODULE,
.dev_name = BFIN_SERIAL_NAME,
.major = BFIN_SERIAL_MAJOR,
.minor = BFIN_SERIAL_MINOR,
- .nr = NR_PORTS,
+ .nr = BFIN_UART_NR_PORTS,
.cons = BFIN_SERIAL_CONSOLE,
};
static int bfin_serial_suspend(struct platform_device *dev, pm_message_t state)
{
- struct bfin_serial_port *uart = platform_get_drvdata(dev);
+ int i;
- if (uart)
- uart_suspend_port(&bfin_serial_reg, &uart->port);
+ for (i = 0; i < nr_active_ports; i++) {
+ if (bfin_serial_ports[i].port.dev != &dev->dev)
+ continue;
+ uart_suspend_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+ }
return 0;
}
static int bfin_serial_resume(struct platform_device *dev)
{
- struct bfin_serial_port *uart = platform_get_drvdata(dev);
+ int i;
- if (uart)
- uart_resume_port(&bfin_serial_reg, &uart->port);
+ for (i = 0; i < nr_active_ports; i++) {
+ if (bfin_serial_ports[i].port.dev != &dev->dev)
+ continue;
+ uart_resume_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+ }
return 0;
}
break;
if (i < dev->num_resources) {
- for (i = 0; i < nr_ports; i++, res++) {
+ for (i = 0; i < nr_active_ports; i++, res++) {
if (bfin_serial_ports[i].port.mapbase != res->start)
continue;
bfin_serial_ports[i].port.dev = &dev->dev;
uart_add_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
- platform_set_drvdata(dev, &bfin_serial_ports[i]);
}
}
return 0;
}
-static int bfin_serial_remove(struct platform_device *pdev)
+static int bfin_serial_remove(struct platform_device *dev)
{
- struct bfin_serial_port *uart = platform_get_drvdata(pdev);
-
+ int i;
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- gpio_free(uart->cts_pin);
- gpio_free(uart->rts_pin);
+ for (i = 0; i < nr_active_ports; i++) {
+ if (bfin_serial_ports[i].port.dev != &dev->dev)
+ continue;
+ uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+ bfin_serial_ports[i].port.dev = NULL;
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+ gpio_free(bfin_serial_ports[i].cts_pin);
+ gpio_free(bfin_serial_ports[i].rts_pin);
#endif
-
- platform_set_drvdata(pdev, NULL);
-
- if (uart)
- uart_remove_one_port(&bfin_serial_reg, &uart->port);
+ }
return 0;
}
.resume = bfin_serial_resume,
.driver = {
.name = "bfin-uart",
+ .owner = THIS_MODULE,
},
};
static int __init bfin_serial_init(void)
{
int ret;
-#ifdef CONFIG_KGDB_UART
- struct bfin_serial_port *uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
- struct ktermios t;
-#endif
pr_info("Serial: Blackfin serial driver\n");
uart_unregister_driver(&bfin_serial_reg);
}
}
-#ifdef CONFIG_KGDB_UART
- if (uart->port.cons->index != CONFIG_KGDB_UART_PORT) {
- request_irq(uart->port.irq, bfin_serial_rx_int,
- IRQF_DISABLED, "BFIN_UART_RX", uart);
- pr_info("Request irq for kgdb uart port\n");
-#ifdef CONFIG_BF54x
- UART_SET_IER(uart, ERBFI);
-#else
- UART_PUT_IER(uart, UART_GET_IER(uart) | ERBFI);
-#endif
- SSYNC();
- t.c_cflag = CS8|B57600;
- t.c_iflag = 0;
- t.c_oflag = 0;
- t.c_lflag = ICANON;
- t.c_line = CONFIG_KGDB_UART_PORT;
- bfin_serial_set_termios(&uart->port, &t, &t);
- }
-#endif
return ret;
}
uart_unregister_driver(&bfin_serial_reg);
}
+
module_init(bfin_serial_init);
module_exit(bfin_serial_exit);
MODULE_DESCRIPTION("Blackfin generic serial port driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR);
+MODULE_ALIAS("platform:bfin-uart");
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff