#
menu "Serial drivers"
+ depends on HAS_IOMEM
#
# The new 8250/16550 serial drivers
kernel will automatically use the first serial line, /dev/ttyS0, as
system console.
+ You can set that using a kernel command line option such as
+ "console=uart8250,io,0x3f8,9600n8"
+ "console=uart8250,mmio,0xff5e0000,115200n8".
+ and it will switch to normal serial console when the corresponding
+ port is ready.
+ "earlycon=uart8250,io,0x3f8,9600n8"
+ "earlycon=uart8250,mmio,0xff5e0000,115200n8".
+ it will not only setup early console.
+
If unsure, say N.
+config FIX_EARLYCON_MEM
+ bool
+ depends on X86
+ default y
+
config SERIAL_8250_GSC
tristate
depends on SERIAL_8250 && GSC
depends on SERIAL_8250 && PCI
default SERIAL_8250
help
- Say Y here if you have PCI serial ports.
-
- To compile this driver as a module, choose M here: the module
- will be called 8250_pci.
+ This builds standard PCI serial support. You may be able to
+ disable this feature if you only need legacy serial support.
+ Saves about 9K.
config SERIAL_8250_PNP
tristate "8250/16550 PNP device support" if EMBEDDED
depends on SERIAL_8250 && PNP
default SERIAL_8250
help
- Say Y here if you have serial ports described by PNPBIOS or ACPI.
- These are typically ports built into the system board.
-
- To compile this driver as a module, choose M here: the module
- will be called 8250_pnp.
+ This builds standard PNP serial support. You may be able to
+ disable this feature if you only need legacy serial support.
config SERIAL_8250_HP300
tristate
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
+config SERIAL_SB1250_DUART
+ tristate "BCM1xxx on-chip DUART serial support"
+ depends on SIBYTE_SB1xxx_SOC=y
+ select SERIAL_CORE
+ default y
+ ---help---
+ Support for the asynchronous serial interface (DUART) included in
+ the BCM1250 and derived System-On-a-Chip (SOC) devices. Note that
+ the letter D in DUART stands for "dual", which is how the device
+ is implemented. Depending on the SOC configuration there may be
+ one or more DUARTs available of which all are handled.
+
+ If unsure, say Y. To compile this driver as a module, choose M here:
+ the module will be called sb1250-duart.
+
+config SERIAL_SB1250_DUART_CONSOLE
+ bool "Support for console on a BCM1xxx DUART serial port"
+ depends on SERIAL_SB1250_DUART=y
+ select SERIAL_CORE_CONSOLE
+ default y
+ ---help---
+ If you say Y here, it will be possible to use a serial port as the
+ system console (the system console is the device which receives all
+ kernel messages and warnings and which allows logins in single user
+ mode).
+
+ If unsure, say Y.
+
config SERIAL_ATMEL
bool "AT91 / AT32 on-chip serial port support"
depends on (ARM && ARCH_AT91) || AVR32
console is the device which receives all kernel messages and
warnings and which allows logins in single user mode).
+config SERIAL_ATMEL_PDC
+ bool "Support DMA transfers on AT91 / AT32 serial port"
+ depends on SERIAL_ATMEL
+ default y
+ help
+ Say Y here if you wish to use the PDC to do DMA transfers to
+ and from the Atmel AT91 / AT32 serial port. In order to
+ actually use DMA transfers, make sure that the use_dma_tx
+ and use_dma_rx members in the atmel_uart_data struct is set
+ appropriately for each port.
+
+ Note that break and error handling currently doesn't work
+ properly when DMA is enabled. Make sure that ports where
+ this matters don't use DMA.
+
config SERIAL_ATMEL_TTYAT
bool "Install as device ttyATn instead of ttySn"
depends on SERIAL_ATMEL=y
Say Y if you have an external 8250/16C550 UART. If unsure, say N.
+config SERIAL_KS8695
+ bool "Micrel KS8695 (Centaur) serial port support"
+ depends on ARCH_KS8695
+ select SERIAL_CORE
+ help
+ This selects the Micrel Centaur KS8695 UART. Say Y here.
+
+config SERIAL_KS8695_CONSOLE
+ bool "Support for console on KS8695 (Centaur) serial port"
+ depends on SERIAL_KS8695=y
+ select SERIAL_CORE_CONSOLE
+ help
+ Say Y here if you wish to use a KS8695 (Centaur) UART as the
+ system console (the system console is the device which
+ receives all kernel messages and warnings and which allows
+ logins in single user mode).
+
config SERIAL_CLPS711X
tristate "CLPS711X serial port support"
depends on ARM && ARCH_CLPS711X
bool "DECstation DZ serial driver"
depends on MACH_DECSTATION && 32BIT
select SERIAL_CORE
- help
- DZ11-family serial controllers for VAXstations, including the
- DC7085, M7814, and M7819.
+ default y
+ ---help---
+ DZ11-family serial controllers for DECstations and VAXstations,
+ including the DC7085, M7814, and M7819.
config SERIAL_DZ_CONSOLE
bool "Support console on DECstation DZ serial driver"
depends on SERIAL_DZ=y
select SERIAL_CORE_CONSOLE
- help
+ default y
+ ---help---
+ If you say Y here, it will be possible to use a serial port as the
+ system console (the system console is the device which receives all
+ kernel messages and warnings and which allows logins in single user
+ mode).
+
+ Note that the firmware uses ttyS3 as the serial console on
+ DECstations that use this driver.
+
+ If unsure, say Y.
+
+config SERIAL_ZS
+ tristate "DECstation Z85C30 serial support"
+ depends on MACH_DECSTATION
+ select SERIAL_CORE
+ default y
+ ---help---
+ Support for the Zilog 85C350 serial communications controller used
+ for serial ports in newer DECstation systems. These include the
+ DECsystem 5900 and all models of the DECstation and DECsystem 5000
+ systems except from model 200.
+
+ If unsure, say Y. To compile this driver as a module, choose M here:
+ the module will be called zs.
+
+config SERIAL_ZS_CONSOLE
+ bool "Support for console on a DECstation Z85C30 serial port"
+ depends on SERIAL_ZS=y
+ select SERIAL_CORE_CONSOLE
+ default y
+ ---help---
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all
kernel messages and warnings and which allows logins in single user
- mode). Note that the firmware uses ttyS0 as the serial console on
- the Maxine and ttyS2 on the others.
+ mode).
+
+ Note that the firmware uses ttyS1 as the serial console on the
+ Maxine and ttyS3 on the others using this driver.
If unsure, say Y.
config SERIAL_BFIN
tristate "Blackfin serial port support"
- depends on BFIN
+ depends on BLACKFIN
select SERIAL_CORE
select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561)
help
config SERIAL_BFIN_CONSOLE
bool "Console on Blackfin serial port"
- depends on SERIAL_BFIN
+ depends on SERIAL_BFIN=y
select SERIAL_CORE_CONSOLE
choice
config SERIAL_BFIN_DMA
bool "DMA mode"
- depends on DMA_UNCACHED_1M
+ depends on !DMA_UNCACHED_NONE && !KGDB_UART
help
This driver works under DMA mode. If this option is selected, the
blackfin simple dma driver is also enabled.
config SERIAL_BFIN_UART1
bool "Enable UART1"
- depends on SERIAL_BFIN && (BF534 || BF536 || BF537)
+ depends on SERIAL_BFIN && (!BF531 && !BF532 && !BF533 && !BF561)
help
Enable UART1
config UART1_CTS_PIN
int "UART1 CTS pin"
- depends on BFIN_UART1_CTSRTS
+ depends on BFIN_UART1_CTSRTS && !BF54x
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
config UART1_RTS_PIN
int "UART1 RTS pin"
- depends on BFIN_UART1_CTSRTS
+ depends on BFIN_UART1_CTSRTS && !BF54x
+ default -1
+ help
+ Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config SERIAL_BFIN_UART2
+ bool "Enable UART2"
+ depends on SERIAL_BFIN && (BF54x)
+ help
+ Enable UART2
+
+config BFIN_UART2_CTSRTS
+ bool "Enable UART2 hardware flow control"
+ depends on SERIAL_BFIN_UART2
+ help
+ Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+ signal.
+
+config UART2_CTS_PIN
+ int "UART2 CTS pin"
+ depends on BFIN_UART2_CTSRTS
+ default -1
+ help
+ Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config UART2_RTS_PIN
+ int "UART2 RTS pin"
+ depends on BFIN_UART2_CTSRTS
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+config SERIAL_BFIN_UART3
+ bool "Enable UART3"
+ depends on SERIAL_BFIN && (BF54x)
+ help
+ Enable UART3
+
+config BFIN_UART3_CTSRTS
+ bool "Enable UART3 hardware flow control"
+ depends on SERIAL_BFIN_UART3
+ help
+ Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+ signal.
+
config SERIAL_IMX
bool "IMX serial port support"
depends on ARM && ARCH_IMX
4. Change the kernel command console parameter to: console=ttyB0
config SERIAL_MUX_CONSOLE
- bool "Support for console on serial MUX"
- depends on SERIAL_MUX
+ bool "Support for console on serial MUX"
+ depends on SERIAL_MUX=y
select SERIAL_CORE_CONSOLE
- default y
+ default y
config PDC_CONSOLE
bool "PDC software console support"
systems. Say Y if you want to be able to use this device.
config SERIAL_IP22_ZILOG
- tristate "IP22 Zilog8530 serial support"
- depends on SGI_IP22
+ tristate "SGI Zilog8530 serial support"
+ depends on SGI_HAS_ZILOG
select SERIAL_CORE
help
- This driver supports the Zilog8530 serial ports found on SGI IP22
+ This driver supports the Zilog8530 serial ports found on SGI
systems. Say Y or M if you want to be able to these serial ports.
config SERIAL_IP22_ZILOG_CONSOLE
- bool "Console on IP22 Zilog8530 serial port"
+ bool "Console on SGI Zilog8530 serial port"
depends on SERIAL_IP22_ZILOG=y
select SERIAL_CORE_CONSOLE
config SERIAL_CORE_CONSOLE
bool
+config CONSOLE_POLL
+ bool
+
config SERIAL_68328
bool "68328 serial support"
depends on M68328 || M68EZ328 || M68VZ328
This driver supports the built-in serial ports of the Motorola ColdFire
family of CPUs.
+config SERIAL_MCF
+ bool "Coldfire serial support (new style driver)"
+ depends on COLDFIRE
+ select SERIAL_CORE
+ help
+ This new serial driver supports the Freescale Coldfire serial ports
+ using the new serial driver subsystem.
+
+config SERIAL_MCF_BAUDRATE
+ int "Default baudrate for Coldfire serial ports"
+ depends on SERIAL_MCF
+ default 19200
+ help
+ This setting lets you define what the default baudrate is for the
+ ColdFire serial ports. The usual default varies from board to board,
+ and this setting is a way of catering for that.
+
+config SERIAL_MCF_CONSOLE
+ bool "Coldfire serial console support"
+ depends on SERIAL_MCF
+ select SERIAL_CORE_CONSOLE
+ help
+ Enable a ColdFire internal serial port to be the system console.
+
config SERIAL_68360_SMC
bool "68360 SMC uart support"
depends on M68360
PowerMac machines.
Say Y or M if you want to be able to these serial ports.
+config SERIAL_PMACZILOG_TTYS
+ bool "Use ttySn device nodes for Zilog z85c30"
+ depends on SERIAL_PMACZILOG
+ help
+ The pmac_zilog driver for the z85C30 chip on many powermacs
+ historically used the device numbers for /dev/ttySn. The
+ 8250 serial port driver also uses these numbers, which means
+ the two drivers being unable to coexist; you could not use
+ both z85C30 and 8250 type ports at the same time.
+
+ If this option is not selected, the pmac_zilog driver will
+ use the device numbers allocated for /dev/ttyPZn. This allows
+ the pmac_zilog and 8250 drivers to co-exist, but may cause
+ existing userspace setups to break. Programs that need to
+ access the built-in serial ports on powermacs will need to
+ be reconfigured to use /dev/ttyPZn instead of /dev/ttySn.
+
+ If you enable this option, any z85c30 ports in the system will
+ be registered as ttyS0 onwards as in the past, and you will be
+ unable to use the 8250 module for PCMCIA or other 16C550-style
+ UARTs.
+
+ Say N unless you need the z85c30 ports on your powermac
+ to appear as /dev/ttySn.
+
config SERIAL_PMACZILOG_CONSOLE
bool "Console on PowerMac z85c30 serial port"
depends on SERIAL_PMACZILOG=y
say Y. Otherwise, say N.
config SERIAL_MPC52xx
- tristate "Freescale MPC52xx family PSC serial support"
- depends on PPC_MPC52xx
+ tristate "Freescale MPC52xx/MPC512x family PSC serial support"
+ depends on PPC_MPC52xx || PPC_MPC512x
select SERIAL_CORE
help
- This drivers support the MPC52xx PSC serial ports. If you would
- like to use them, you must answer Y or M to this option. Not that
+ This driver supports MPC52xx and MPC512x PSC serial ports. If you would
+ like to use them, you must answer Y or M to this option. Note that
for use as console, it must be included in kernel and not as a
module.
config SERIAL_MPC52xx_CONSOLE
- bool "Console on a Freescale MPC52xx family PSC serial port"
+ bool "Console on a Freescale MPC52xx/MPC512x family PSC serial port"
depends on SERIAL_MPC52xx=y
select SERIAL_CORE_CONSOLE
help
of the Freescale MPC52xx family as a console.
config SERIAL_MPC52xx_CONSOLE_BAUD
- int "Freescale MPC52xx family PSC serial port baud"
+ int "Freescale MPC52xx/MPC512x family PSC serial port baud"
depends on SERIAL_MPC52xx_CONSOLE=y
default "9600"
help
config SERIAL_VR41XX_CONSOLE
bool "Enable NEC VR4100 series Serial Interface Unit console"
- depends on SERIAL_VR41XX
+ depends on SERIAL_VR41XX=y
select SERIAL_CORE_CONSOLE
help
If you have a NEC VR4100 series processor and you want to use
depends on SERIAL_NETX
select SERIAL_CORE_CONSOLE
help
- If you have enabled the serial port on the Motorola IMX
- CPU you can make it the console by answering Y to this option.
+ If you have enabled the serial port on the Hilscher NetX SoC
+ you can make it the console by answering Y to this option.
config SERIAL_OF_PLATFORM
tristate "Serial port on Open Firmware platform bus"
Currently, only 8250 compatible ports are supported, but
others can easily be added.
+config SERIAL_QE
+ tristate "Freescale QUICC Engine serial port support"
+ depends on QUICC_ENGINE
+ select SERIAL_CORE
+ select FW_LOADER
+ default n
+ help
+ This driver supports the QE serial ports on Freescale embedded
+ PowerPC that contain a QUICC Engine.
+
+config SERIAL_SC26XX
+ tristate "SC2681/SC2692 serial port support"
+ depends on SNI_RM
+ select SERIAL_CORE
+ help
+ This is a driver for the onboard serial ports of
+ older RM400 machines.
+
+config SERIAL_SC26XX_CONSOLE
+ bool "Console on SC2681/SC2692 serial port"
+ depends on SERIAL_SC26XX
+ select SERIAL_CORE_CONSOLE
+ help
+ Support for Console on SC2681/SC2692 serial ports.
+
endmenu
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff