#
# Serial device configuration
#
-# $Id: Kconfig,v 1.11 2004/03/11 18:08:04 lethal Exp $
-#
menu "Serial drivers"
depends on HAS_IOMEM
# The new 8250/16550 serial drivers
config SERIAL_8250
tristate "8250/16550 and compatible serial support"
- depends on (BROKEN || !SPARC)
select SERIAL_CORE
---help---
This selects whether you want to include the driver for the standard
cards. If unsure, say N.
config SERIAL_8250_AU1X00
- bool "AU1X00 serial port support"
+ bool "Au1x00 serial port support"
depends on SERIAL_8250 != n && SOC_AU1X00
help
- If you have an Au1x00 board and want to use the serial port, say Y
- to this option. The driver can handle 1 or 2 serial ports.
- If unsure, say N.
+ If you have an Au1x00 SOC based board and want to use the serial port,
+ say Y to this option. The driver can handle up to 4 serial ports,
+ depending on the SOC. If unsure, say N.
config SERIAL_8250_RM9K
bool "Support for MIPS RM9xxx integrated serial port"
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
-config SERIAL_S3C2410
- tristate "Samsung S3C2410/S3C2440/S3C2442/S3C2412 Serial port support"
- depends on ARM && ARCH_S3C2410
+config SERIAL_SAMSUNG
+ tristate "Samsung SoC serial support"
+ depends on ARM && PLAT_S3C
select SERIAL_CORE
help
Support for the on-chip UARTs on the Samsung S3C24XX series CPUs,
provide all of these ports, depending on how the serial port
pins are configured.
- Currently this driver supports the UARTS on the S3C2410, S3C2440,
- S3C2442, S3C2412 and S3C2413 CPUs.
-
-config SERIAL_S3C2410_CONSOLE
- bool "Support for console on S3C2410 serial port"
- depends on SERIAL_S3C2410=y
+config SERIAL_SAMSUNG_UARTS
+ int
+ depends on ARM && PLAT_S3C
+ default 2 if ARCH_S3C2400
+ default 4 if ARCH_S5PC1XX || ARCH_S3C64XX || CPU_S3C2443
+ default 3
+ help
+ Select the number of available UART ports for the Samsung S3C
+ serial driver
+
+config SERIAL_SAMSUNG_DEBUG
+ bool "Samsung SoC serial debug"
+ depends on SERIAL_SAMSUNG && DEBUG_LL
+ help
+ Add support for debugging the serial driver. Since this is
+ generally being used as a console, we use our own output
+ routines that go via the low-level debug printascii()
+ function.
+
+config SERIAL_SAMSUNG_CONSOLE
+ bool "Support for console on Samsung SoC serial port"
+ depends on SERIAL_SAMSUNG=y
select SERIAL_CORE_CONSOLE
help
Allow selection of the S3C24XX on-board serial ports for use as
your boot loader about how to pass options to the kernel at
boot time.)
+config SERIAL_S3C2400
+ tristate "Samsung S3C2410 Serial port support"
+ depends on ARM && SERIAL_SAMSUNG && CPU_S3C2400
+ default y if CPU_S3C2400
+ help
+ Serial port support for the Samsung S3C2400 SoC
+
+config SERIAL_S3C2410
+ tristate "Samsung S3C2410 Serial port support"
+ depends on SERIAL_SAMSUNG && CPU_S3C2410
+ default y if CPU_S3C2410
+ help
+ Serial port support for the Samsung S3C2410 SoC
+
+config SERIAL_S3C2412
+ tristate "Samsung S3C2412/S3C2413 Serial port support"
+ depends on SERIAL_SAMSUNG && CPU_S3C2412
+ default y if CPU_S3C2412
+ help
+ Serial port support for the Samsung S3C2412 and S3C2413 SoC
+
+config SERIAL_S3C2440
+ tristate "Samsung S3C2440/S3C2442 Serial port support"
+ depends on SERIAL_SAMSUNG && (CPU_S3C2440 || CPU_S3C2442)
+ default y if CPU_S3C2440
+ default y if CPU_S3C2442
+ help
+ Serial port support for the Samsung S3C2440 and S3C2442 SoC
+
+config SERIAL_S3C24A0
+ tristate "Samsung S3C24A0 Serial port support"
+ depends on SERIAL_SAMSUNG && CPU_S3C24A0
+ default y if CPU_S3C24A0
+ help
+ Serial port support for the Samsung S3C24A0 SoC
+
+config SERIAL_S3C6400
+ tristate "Samsung S3C6400/S3C6410 Serial port support"
+ depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410)
+ default y
+ help
+ Serial port support for the Samsung S3C6400 and S3C6410
+ SoCs
+
+config SERIAL_S5PC100
+ tristate "Samsung S5PC100 Serial port support"
+ depends on SERIAL_SAMSUNG && CPU_S5PC100
+ default y
+ help
+ Serial port support for the Samsung S5PC100 SoCs
+
+config SERIAL_MAX3100
+ tristate "MAX3100 support"
+ depends on SPI
+ select SERIAL_CORE
+ help
+ MAX3100 chip support
+
config SERIAL_DZ
bool "DECstation DZ serial driver"
depends on MACH_DECSTATION && 32BIT
config SERIAL_PXA
bool "PXA serial port support"
- depends on ARM && ARCH_PXA
+ depends on ARCH_PXA || ARCH_MMP
select SERIAL_CORE
help
If you have a machine based on an Intel XScale PXA2xx CPU you
config SERIAL_BFIN_DMA
bool "DMA mode"
- depends on !DMA_UNCACHED_NONE && !KGDB_UART
+ depends on !DMA_UNCACHED_NONE && KGDB_SERIAL_CONSOLE=n
help
This driver works under DMA mode. If this option is selected, the
blackfin simple dma driver is also enabled.
config UART0_CTS_PIN
int "UART0 CTS pin"
- depends on BFIN_UART0_CTSRTS
+ depends on BFIN_UART0_CTSRTS && !BF548
default 23
help
The default pin is GPIO_GP7.
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config UART0_RTS_PIN
int "UART0 RTS pin"
- depends on BFIN_UART0_CTSRTS
+ depends on BFIN_UART0_CTSRTS && !BF548
default 22
help
The default pin is GPIO_GP6.
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config SERIAL_BFIN_UART1
bool "Enable UART1"
config UART1_CTS_PIN
int "UART1 CTS pin"
- depends on BFIN_UART1_CTSRTS && !BF54x
+ depends on BFIN_UART1_CTSRTS && !BF548
default -1
help
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config UART1_RTS_PIN
int "UART1 RTS pin"
- depends on BFIN_UART1_CTSRTS && !BF54x
+ depends on BFIN_UART1_CTSRTS && !BF548
default -1
help
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config SERIAL_BFIN_UART2
bool "Enable UART2"
- depends on SERIAL_BFIN && (BF54x)
+ depends on SERIAL_BFIN && (BF54x || BF538 || BF539)
help
Enable UART2
config UART2_CTS_PIN
int "UART2 CTS pin"
- depends on BFIN_UART2_CTSRTS
+ depends on BFIN_UART2_CTSRTS && !BF548
default -1
help
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config UART2_RTS_PIN
int "UART2 RTS pin"
- depends on BFIN_UART2_CTSRTS
+ depends on BFIN_UART2_CTSRTS && !BF548
default -1
help
- Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
config SERIAL_BFIN_UART3
bool "Enable UART3"
Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
signal.
+config UART3_CTS_PIN
+ int "UART3 CTS pin"
+ depends on BFIN_UART3_CTSRTS && !BF548
+ default -1
+ help
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
+config UART3_RTS_PIN
+ int "UART3 RTS pin"
+ depends on BFIN_UART3_CTSRTS && !BF548
+ default -1
+ help
+ Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
config SERIAL_IMX
bool "IMX serial port support"
- depends on ARM && ARCH_IMX
+ depends on ARM && (ARCH_IMX || ARCH_MXC)
select SERIAL_CORE
+ select RATIONAL
help
If you have a machine based on a Motorola IMX CPU you
can enable its onboard serial port by enabling this option.
config SERIAL_UARTLITE
tristate "Xilinx uartlite serial port support"
- depends on PPC32
+ depends on PPC32 || MICROBLAZE
select SERIAL_CORE
help
Say Y here if you want to use the Xilinx uartlite serial controller.
To compile this driver as a module, choose M here: the
- module will be called uartlite.ko.
+ module will be called uartlite.
config SERIAL_UARTLITE_CONSOLE
bool "Support for console on Xilinx uartlite serial port"
depends on SERIAL_IP22_ZILOG=y
select SERIAL_CORE_CONSOLE
-config V850E_UART
- bool "NEC V850E on-chip UART support"
- depends on V850E_MA1 || V850E_ME2 || V850E_TEG || V850E2_ANNA || V850E_AS85EP1
- select SERIAL_CORE
- default y
-
-config V850E_UARTB
- bool
- depends on V850E_UART && V850E_ME2
- default y
-
-config V850E_UART_CONSOLE
- bool "Use NEC V850E on-chip UART for console"
- depends on V850E_UART
- select SERIAL_CORE_CONSOLE
-
config SERIAL_SH_SCI
tristate "SuperH SCI(F) serial port support"
depends on SUPERH || H8300
config SERIAL_PNX8XXX
bool "Enable PNX8XXX SoCs' UART Support"
- depends on MIPS && SOC_PNX8550
+ depends on MIPS && (SOC_PNX8550 || SOC_PNX833X)
select SERIAL_CORE
help
If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
config SERIAL_CORE_CONSOLE
bool
+config CONSOLE_POLL
+ bool
+
config SERIAL_68328
bool "68328 serial support"
depends on M68328 || M68EZ328 || M68VZ328
bool "Support RTS/CTS on 68328 serial port"
depends on SERIAL_68328
-config SERIAL_COLDFIRE
- bool "ColdFire serial support"
- depends on COLDFIRE
- help
- This driver supports the built-in serial ports of the Motorola ColdFire
- family of CPUs.
-
config SERIAL_MCF
- bool "Coldfire serial support (new style driver)"
+ bool "Coldfire serial support"
depends on COLDFIRE
select SERIAL_CORE
help
- This new serial driver supports the Freescale Coldfire serial ports
- using the new serial driver subsystem.
+ This serial driver supports the Freescale Coldfire serial ports.
config SERIAL_MCF_BAUDRATE
int "Default baudrate for Coldfire serial ports"
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
-config SERIAL_CPM_SCC1
- bool "Support for SCC1 serial port"
- depends on SERIAL_CPM=y
- help
- Select this option to use SCC1 as a serial port
-
-config SERIAL_CPM_SCC2
- bool "Support for SCC2 serial port"
- depends on SERIAL_CPM=y
- help
- Select this option to use SCC2 as a serial port
-
-config SERIAL_CPM_SCC3
- bool "Support for SCC3 serial port"
- depends on SERIAL_CPM=y
- help
- Select this option to use SCC3 as a serial port
-
-config SERIAL_CPM_SCC4
- bool "Support for SCC4 serial port"
- depends on SERIAL_CPM=y
- help
- Select this option to use SCC4 as a serial port
-
-config SERIAL_CPM_SMC1
- bool "Support for SMC1 serial port"
- depends on SERIAL_CPM=y
- help
- Select this option to use SMC1 as a serial port
-
-config SERIAL_CPM_SMC2
- bool "Support for SMC2 serial port"
- depends on SERIAL_CPM=y
- help
- Select this option to use SMC2 as a serial port
-
config SERIAL_SGI_L1_CONSOLE
bool "SGI Altix L1 serial console support"
depends on IA64_GENERIC || IA64_SGI_SN2
If you have an SGI Altix with an IOC3 serial card,
say Y or M. Otherwise, say N.
+config SERIAL_MSM
+ bool "MSM on-chip serial port support"
+ depends on ARM && ARCH_MSM
+ select SERIAL_CORE
+
+config SERIAL_MSM_CONSOLE
+ bool "MSM serial console support"
+ depends on SERIAL_MSM=y
+ select SERIAL_CORE_CONSOLE
+
config SERIAL_NETX
- bool "NetX serial port support"
+ tristate "NetX serial port support"
depends on ARM && ARCH_NETX
select SERIAL_CORE
help
config SERIAL_NETX_CONSOLE
bool "Console on NetX serial port"
- depends on SERIAL_NETX
+ depends on SERIAL_NETX=y
select SERIAL_CORE_CONSOLE
help
If you have enabled the serial port on the Hilscher NetX SoC
config SERIAL_OF_PLATFORM
tristate "Serial port on Open Firmware platform bus"
- depends on PPC_OF
- depends on SERIAL_8250
+ depends on PPC_OF || MICROBLAZE
+ depends on SERIAL_8250 || SERIAL_OF_PLATFORM_NWPSERIAL
help
If you have a PowerPC based system that has serial ports
on a platform specific bus, you should enable this option.
Currently, only 8250 compatible ports are supported, but
others can easily be added.
+config SERIAL_OF_PLATFORM_NWPSERIAL
+ tristate "NWP serial port driver"
+ depends on PPC_OF && PPC_DCR
+ select SERIAL_OF_PLATFORM
+ select SERIAL_CORE_CONSOLE
+ select SERIAL_CORE
+ help
+ This driver supports the cell network processor nwp serial
+ device.
+
+config SERIAL_OF_PLATFORM_NWPSERIAL_CONSOLE
+ bool "Console on NWP serial port"
+ depends on SERIAL_OF_PLATFORM_NWPSERIAL=y
+ select SERIAL_CORE_CONSOLE
+ help
+ Support for Console on the NWP serial ports.
+
config SERIAL_QE
tristate "Freescale QUICC Engine serial port support"
depends on QUICC_ENGINE
help
Support for Console on SC2681/SC2692 serial ports.
+config SERIAL_BFIN_SPORT
+ tristate "Blackfin SPORT emulate UART (EXPERIMENTAL)"
+ depends on BLACKFIN && EXPERIMENTAL
+ select SERIAL_CORE
+ help
+ Enable SPORT emulate UART on Blackfin series.
+
+ To compile this driver as a module, choose M here: the
+ module will be called bfin_sport_uart.
+
+choice
+ prompt "Baud rate for Blackfin SPORT UART"
+ depends on SERIAL_BFIN_SPORT
+ default SERIAL_SPORT_BAUD_RATE_57600
+ help
+ Choose a baud rate for the SPORT UART, other uart settings are
+ 8 bit, 1 stop bit, no parity, no flow control.
+
+config SERIAL_SPORT_BAUD_RATE_115200
+ bool "115200"
+
+config SERIAL_SPORT_BAUD_RATE_57600
+ bool "57600"
+
+config SERIAL_SPORT_BAUD_RATE_38400
+ bool "38400"
+
+config SERIAL_SPORT_BAUD_RATE_19200
+ bool "19200"
+
+config SERIAL_SPORT_BAUD_RATE_9600
+ bool "9600"
+endchoice
+
+config SPORT_BAUD_RATE
+ int
+ depends on SERIAL_BFIN_SPORT
+ default 115200 if (SERIAL_SPORT_BAUD_RATE_115200)
+ default 57600 if (SERIAL_SPORT_BAUD_RATE_57600)
+ default 38400 if (SERIAL_SPORT_BAUD_RATE_38400)
+ default 19200 if (SERIAL_SPORT_BAUD_RATE_19200)
+ default 9600 if (SERIAL_SPORT_BAUD_RATE_9600)
+
+config SERIAL_TIMBERDALE
+ tristate "Support for timberdale UART"
+ depends on MFD_TIMBERDALE
+ select SERIAL_CORE
+ ---help---
+ Add support for UART controller on timberdale.
+
endmenu
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff