* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License.
- *
- * $Id: 8250_pci.c,v 1.28 2002/11/02 11:14:18 rmk Exp $
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/pci.h>
-#include <linux/sched.h>
#include <linux/string.h>
#include <linux/kernel.h>
#include <linux/slab.h>
len = pci_resource_len(dev, bar);
if (!priv->remapped_bar[bar])
- priv->remapped_bar[bar] = ioremap(base, len);
+ priv->remapped_bar[bar] = ioremap_nocache(base, len);
if (!priv->remapped_bar[bar])
return -ENOMEM;
}
/*
+ * ADDI-DATA GmbH communication cards <info@addi-data.com>
+ */
+static int addidata_apci7800_setup(struct serial_private *priv,
+ struct pciserial_board *board,
+ struct uart_port *port, int idx)
+{
+ unsigned int bar = 0, offset = board->first_offset;
+ bar = FL_GET_BASE(board->flags);
+
+ if (idx < 2) {
+ offset += idx * board->uart_offset;
+ } else if ((idx >= 2) && (idx < 4)) {
+ bar += 1;
+ offset += ((idx - 2) * board->uart_offset);
+ } else if ((idx >= 4) && (idx < 6)) {
+ bar += 2;
+ offset += ((idx - 4) * board->uart_offset);
+ } else if (idx >= 6) {
+ bar += 3;
+ offset += ((idx - 6) * board->uart_offset);
+ }
+
+ return setup_port(priv, port, bar, offset, board->reg_shift);
+}
+
+/*
* AFAVLAB uses a different mixture of BARs and offsets
* Not that ugly ;) -- HW
*/
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
-
+
bar = FL_GET_BASE(board->flags);
if (idx < 4)
bar += idx;
* and Keystone have one Diva chip with 3 UARTs. Some later machines have
* one Diva chip, but it has been expanded to 5 UARTs.
*/
-static int __devinit pci_hp_diva_init(struct pci_dev *dev)
+static int pci_hp_diva_init(struct pci_dev *dev)
{
int rc = 0;
rc = 4;
break;
case PCI_DEVICE_ID_HP_DIVA_POWERBAR:
+ case PCI_DEVICE_ID_HP_DIVA_HURRICANE:
rc = 1;
break;
}
/*
* Added for EKF Intel i960 serial boards
*/
-static int __devinit pci_inteli960ni_init(struct pci_dev *dev)
+static int pci_inteli960ni_init(struct pci_dev *dev)
{
unsigned long oldval;
return -ENODEV;
/* is firmware started? */
- pci_read_config_dword(dev, 0x44, (void*) &oldval);
- if (oldval == 0x00001000L) { /* RESET value */
+ pci_read_config_dword(dev, 0x44, (void *)&oldval);
+ if (oldval == 0x00001000L) { /* RESET value */
printk(KERN_DEBUG "Local i960 firmware missing");
return -ENODEV;
}
* seems to be mainly needed on card using the PLX which also use I/O
* mapped memory.
*/
-static int __devinit pci_plx9050_init(struct pci_dev *dev)
+static int pci_plx9050_init(struct pci_dev *dev)
{
u8 irq_config;
void __iomem *p;
}
irq_config = 0x41;
- if (dev->vendor == PCI_VENDOR_ID_PANACOM)
+ if (dev->vendor == PCI_VENDOR_ID_PANACOM ||
+ dev->subsystem_vendor == PCI_SUBVENDOR_ID_EXSYS)
irq_config = 0x43;
+
if ((dev->vendor == PCI_VENDOR_ID_PLX) &&
- (dev->device == PCI_DEVICE_ID_PLX_ROMULUS)) {
+ (dev->device == PCI_DEVICE_ID_PLX_ROMULUS))
/*
* As the megawolf cards have the int pins active
* high, and have 2 UART chips, both ints must be
* deep FIFOs
*/
irq_config = 0x5b;
- }
-
/*
* enable/disable interrupts
*/
- p = ioremap(pci_resource_start(dev, 0), 0x80);
+ p = ioremap_nocache(pci_resource_start(dev, 0), 0x80);
if (p == NULL)
return -ENOMEM;
writel(irq_config, p + 0x4c);
/*
* disable interrupts
*/
- p = ioremap(pci_resource_start(dev, 0), 0x80);
+ p = ioremap_nocache(pci_resource_start(dev, 0), 0x80);
if (p != NULL) {
writel(0, p + 0x4c);
/* global control register offset for SBS PMC-OctalPro */
#define OCT_REG_CR_OFF 0x500
-static int __devinit sbs_init(struct pci_dev *dev)
+static int sbs_init(struct pci_dev *dev)
{
u8 __iomem *p;
- p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
+ p = ioremap_nocache(pci_resource_start(dev, 0),
+ pci_resource_len(dev, 0));
if (p == NULL)
return -ENOMEM;
/* Set bit-4 Control Register (UART RESET) in to reset the uarts */
- writeb(0x10,p + OCT_REG_CR_OFF);
+ writeb(0x10, p + OCT_REG_CR_OFF);
udelay(50);
- writeb(0x0,p + OCT_REG_CR_OFF);
+ writeb(0x0, p + OCT_REG_CR_OFF);
/* Set bit-2 (INTENABLE) of Control Register */
writeb(0x4, p + OCT_REG_CR_OFF);
{
u8 __iomem *p;
- p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
- if (p != NULL) {
+ p = ioremap_nocache(pci_resource_start(dev, 0),
+ pci_resource_len(dev, 0));
+ /* FIXME: What if resource_len < OCT_REG_CR_OFF */
+ if (p != NULL)
writeb(0, p + OCT_REG_CR_OFF);
- }
iounmap(p);
}
* with other OSes (like M$ DOS).
*
* SIIG support added by Andrey Panin <pazke@donpac.ru>, 10/1999
- *
+ *
* There is two family of SIIG serial cards with different PCI
* interface chip and different configuration methods:
* - 10x cards have control registers in IO and/or memory space;
break;
}
- p = ioremap(pci_resource_start(dev, 0), 0x80);
+ p = ioremap_nocache(pci_resource_start(dev, 0), 0x80);
if (p == NULL)
return -ENOMEM;
return -ENODEV;
}
+static int pci_siig_setup(struct serial_private *priv,
+ struct pciserial_board *board,
+ struct uart_port *port, int idx)
+{
+ unsigned int bar = FL_GET_BASE(board->flags) + idx, offset = 0;
+
+ if (idx > 3) {
+ bar = 4;
+ offset = (idx - 4) * 8;
+ }
+
+ return setup_port(priv, port, bar, offset, 0);
+}
+
/*
* Timedia has an explosion of boards, and to avoid the PCI table from
* growing *huge*, we use this function to collapse some 70 entries
* in the PCI table into one, for sanity's and compactness's sake.
*/
-static unsigned short timedia_single_port[] = {
+static const unsigned short timedia_single_port[] = {
0x4025, 0x4027, 0x4028, 0x5025, 0x5027, 0
};
-static unsigned short timedia_dual_port[] = {
+static const unsigned short timedia_dual_port[] = {
0x0002, 0x4036, 0x4037, 0x4038, 0x4078, 0x4079, 0x4085,
- 0x4088, 0x4089, 0x5037, 0x5078, 0x5079, 0x5085, 0x6079,
- 0x7079, 0x8079, 0x8137, 0x8138, 0x8237, 0x8238, 0x9079,
+ 0x4088, 0x4089, 0x5037, 0x5078, 0x5079, 0x5085, 0x6079,
+ 0x7079, 0x8079, 0x8137, 0x8138, 0x8237, 0x8238, 0x9079,
0x9137, 0x9138, 0x9237, 0x9238, 0xA079, 0xB079, 0xC079,
0xD079, 0
};
-static unsigned short timedia_quad_port[] = {
- 0x4055, 0x4056, 0x4095, 0x4096, 0x5056, 0x8156, 0x8157,
- 0x8256, 0x8257, 0x9056, 0x9156, 0x9157, 0x9158, 0x9159,
+static const unsigned short timedia_quad_port[] = {
+ 0x4055, 0x4056, 0x4095, 0x4096, 0x5056, 0x8156, 0x8157,
+ 0x8256, 0x8257, 0x9056, 0x9156, 0x9157, 0x9158, 0x9159,
0x9256, 0x9257, 0xA056, 0xA157, 0xA158, 0xA159, 0xB056,
0xB157, 0
};
-static unsigned short timedia_eight_port[] = {
- 0x4065, 0x4066, 0x5065, 0x5066, 0x8166, 0x9066, 0x9166,
+static const unsigned short timedia_eight_port[] = {
+ 0x4065, 0x4066, 0x5065, 0x5066, 0x8166, 0x9066, 0x9166,
0x9167, 0x9168, 0xA066, 0xA167, 0xA168, 0
};
-static struct timedia_struct {
+static const struct timedia_struct {
int num;
- unsigned short *ids;
+ const unsigned short *ids;
} timedia_data[] = {
{ 1, timedia_single_port },
{ 2, timedia_dual_port },
{ 4, timedia_quad_port },
- { 8, timedia_eight_port },
- { 0, NULL }
+ { 8, timedia_eight_port }
};
-static int __devinit pci_timedia_init(struct pci_dev *dev)
+static int pci_timedia_init(struct pci_dev *dev)
{
- unsigned short *ids;
+ const unsigned short *ids;
int i, j;
- for (i = 0; timedia_data[i].num; i++) {
+ for (i = 0; i < ARRAY_SIZE(timedia_data); i++) {
ids = timedia_data[i].ids;
for (j = 0; ids[j]; j++)
if (dev->subsystem_device == ids[j])
break;
case 3:
offset = board->uart_offset;
- bar = 1;
+ /* FALLTHROUGH */
case 4: /* BAR 2 */
case 5: /* BAR 3 */
case 6: /* BAR 4 */
return setup_port(priv, port, bar, offset, board->reg_shift);
}
-static int __devinit pci_xircom_init(struct pci_dev *dev)
+static int pci_xircom_init(struct pci_dev *dev)
{
msleep(100);
return 0;
}
-static int __devinit pci_netmos_init(struct pci_dev *dev)
+static int pci_netmos_init(struct pci_dev *dev)
{
/* subdevice 0x00PS means <P> parallel, <S> serial */
unsigned int num_serial = dev->subsystem_device & 0xf;
return num_serial;
}
+/*
+ * ITE support by Niels de Vos <niels.devos@wincor-nixdorf.com>
+ *
+ * These chips are available with optionally one parallel port and up to
+ * two serial ports. Unfortunately they all have the same product id.
+ *
+ * Basic configuration is done over a region of 32 I/O ports. The base
+ * ioport is called INTA or INTC, depending on docs/other drivers.
+ *
+ * The region of the 32 I/O ports is configured in POSIO0R...
+ */
+
+/* registers */
+#define ITE_887x_MISCR 0x9c
+#define ITE_887x_INTCBAR 0x78
+#define ITE_887x_UARTBAR 0x7c
+#define ITE_887x_PS0BAR 0x10
+#define ITE_887x_POSIO0 0x60
+
+/* I/O space size */
+#define ITE_887x_IOSIZE 32
+/* I/O space size (bits 26-24; 8 bytes = 011b) */
+#define ITE_887x_POSIO_IOSIZE_8 (3 << 24)
+/* I/O space size (bits 26-24; 32 bytes = 101b) */
+#define ITE_887x_POSIO_IOSIZE_32 (5 << 24)
+/* Decoding speed (1 = slow, 2 = medium, 3 = fast) */
+#define ITE_887x_POSIO_SPEED (3 << 29)
+/* enable IO_Space bit */
+#define ITE_887x_POSIO_ENABLE (1 << 31)
+
+static int pci_ite887x_init(struct pci_dev *dev)
+{
+ /* inta_addr are the configuration addresses of the ITE */
+ static const short inta_addr[] = { 0x2a0, 0x2c0, 0x220, 0x240, 0x1e0,
+ 0x200, 0x280, 0 };
+ int ret, i, type;
+ struct resource *iobase = NULL;
+ u32 miscr, uartbar, ioport;
+
+ /* search for the base-ioport */
+ i = 0;
+ while (inta_addr[i] && iobase == NULL) {
+ iobase = request_region(inta_addr[i], ITE_887x_IOSIZE,
+ "ite887x");
+ if (iobase != NULL) {
+ /* write POSIO0R - speed | size | ioport */
+ pci_write_config_dword(dev, ITE_887x_POSIO0,
+ ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED |
+ ITE_887x_POSIO_IOSIZE_32 | inta_addr[i]);
+ /* write INTCBAR - ioport */
+ pci_write_config_dword(dev, ITE_887x_INTCBAR,
+ inta_addr[i]);
+ ret = inb(inta_addr[i]);
+ if (ret != 0xff) {
+ /* ioport connected */
+ break;
+ }
+ release_region(iobase->start, ITE_887x_IOSIZE);
+ iobase = NULL;
+ }
+ i++;
+ }
+
+ if (!inta_addr[i]) {
+ printk(KERN_ERR "ite887x: could not find iobase\n");
+ return -ENODEV;
+ }
+
+ /* start of undocumented type checking (see parport_pc.c) */
+ type = inb(iobase->start + 0x18) & 0x0f;
+
+ switch (type) {
+ case 0x2: /* ITE8871 (1P) */
+ case 0xa: /* ITE8875 (1P) */
+ ret = 0;
+ break;
+ case 0xe: /* ITE8872 (2S1P) */
+ ret = 2;
+ break;
+ case 0x6: /* ITE8873 (1S) */
+ ret = 1;
+ break;
+ case 0x8: /* ITE8874 (2S) */
+ ret = 2;
+ break;
+ default:
+ moan_device("Unknown ITE887x", dev);
+ ret = -ENODEV;
+ }
+
+ /* configure all serial ports */
+ for (i = 0; i < ret; i++) {
+ /* read the I/O port from the device */
+ pci_read_config_dword(dev, ITE_887x_PS0BAR + (0x4 * (i + 1)),
+ &ioport);
+ ioport &= 0x0000FF00; /* the actual base address */
+ pci_write_config_dword(dev, ITE_887x_POSIO0 + (0x4 * (i + 1)),
+ ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED |
+ ITE_887x_POSIO_IOSIZE_8 | ioport);
+
+ /* write the ioport to the UARTBAR */
+ pci_read_config_dword(dev, ITE_887x_UARTBAR, &uartbar);
+ uartbar &= ~(0xffff << (16 * i)); /* clear half the reg */
+ uartbar |= (ioport << (16 * i)); /* set the ioport */
+ pci_write_config_dword(dev, ITE_887x_UARTBAR, uartbar);
+
+ /* get current config */
+ pci_read_config_dword(dev, ITE_887x_MISCR, &miscr);
+ /* disable interrupts (UARTx_Routing[3:0]) */
+ miscr &= ~(0xf << (12 - 4 * i));
+ /* activate the UART (UARTx_En) */
+ miscr |= 1 << (23 - i);
+ /* write new config with activated UART */
+ pci_write_config_dword(dev, ITE_887x_MISCR, miscr);
+ }
+
+ if (ret <= 0) {
+ /* the device has no UARTs if we get here */
+ release_region(iobase->start, ITE_887x_IOSIZE);
+ }
+
+ return ret;
+}
+
+static void __devexit pci_ite887x_exit(struct pci_dev *dev)
+{
+ u32 ioport;
+ /* the ioport is bit 0-15 in POSIO0R */
+ pci_read_config_dword(dev, ITE_887x_POSIO0, &ioport);
+ ioport &= 0xffff;
+ release_region(ioport, ITE_887x_IOSIZE);
+}
+
static int
pci_default_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
else
offset += idx * board->uart_offset;
- maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) /
- (8 << board->reg_shift);
+ maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) >>
+ (board->reg_shift + 3);
if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr)
return 1;
-
+
return setup_port(priv, port, bar, offset, board->reg_shift);
}
#define PCI_SUBDEVICE_ID_POCTAL232 0x0308
#define PCI_SUBDEVICE_ID_POCTAL422 0x0408
+/* Unknown vendors/cards - this should not be in linux/pci_ids.h */
+#define PCI_SUBDEVICE_ID_UNKNOWN_0x1584 0x1584
+
/*
* Master list of serial port init/setup/exit quirks.
* This does not describe the general nature of the port.
* This list is ordered alphabetically by vendor then device.
* Specific entries must come before more generic entries.
*/
-static struct pci_serial_quirk pci_serial_quirks[] = {
+static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
+ /*
+ * ADDI-DATA GmbH communication cards <info@addi-data.com>
+ */
+ {
+ .vendor = PCI_VENDOR_ID_ADDIDATA_OLD,
+ .device = PCI_DEVICE_ID_ADDIDATA_APCI7800,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = addidata_apci7800_setup,
+ },
/*
- * AFAVLAB cards.
+ * AFAVLAB cards - these may be called via parport_serial
* It is not clear whether this applies to all products.
*/
{
.setup = pci_default_setup,
},
/*
+ * ITE
+ */
+ {
+ .vendor = PCI_VENDOR_ID_ITE,
+ .device = PCI_DEVICE_ID_ITE_8872,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_ite887x_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_ite887x_exit),
+ },
+ /*
* Panacom
*/
{
.init = pci_plx9050_init,
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
- },
+ },
{
.vendor = PCI_VENDOR_ID_PANACOM,
.device = PCI_DEVICE_ID_PANACOM_DUALMODEM,
*/
{
.vendor = PCI_VENDOR_ID_PLX,
+ .device = PCI_DEVICE_ID_PLX_9030,
+ .subvendor = PCI_SUBVENDOR_ID_PERLE,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_default_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_PLX,
+ .device = PCI_DEVICE_ID_PLX_9050,
+ .subvendor = PCI_SUBVENDOR_ID_EXSYS,
+ .subdevice = PCI_SUBDEVICE_ID_EXSYS_4055,
+ .init = pci_plx9050_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_plx9050_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_PLX,
.device = PCI_DEVICE_ID_PLX_9050,
.subvendor = PCI_SUBVENDOR_ID_KEYSPAN,
.subdevice = PCI_SUBDEVICE_ID_KEYSPAN_SX2,
},
{
.vendor = PCI_VENDOR_ID_PLX,
+ .device = PCI_DEVICE_ID_PLX_9050,
+ .subvendor = PCI_VENDOR_ID_PLX,
+ .subdevice = PCI_SUBDEVICE_ID_UNKNOWN_0x1584,
+ .init = pci_plx9050_init,
+ .setup = pci_default_setup,
+ .exit = __devexit_p(pci_plx9050_exit),
+ },
+ {
+ .vendor = PCI_VENDOR_ID_PLX,
.device = PCI_DEVICE_ID_PLX_ROMULUS,
.subvendor = PCI_VENDOR_ID_PLX,
.subdevice = PCI_DEVICE_ID_PLX_ROMULUS,
.exit = __devexit_p(sbs_exit),
},
/*
- * SIIG cards.
+ * SIIG cards - these may be called via parport_serial
*/
{
.vendor = PCI_VENDOR_ID_SIIG,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_siig_init,
- .setup = pci_default_setup,
+ .setup = pci_siig_setup,
},
/*
* Titan cards
.setup = pci_default_setup,
},
/*
- * Netmos cards
+ * Netmos cards - these may be called via parport_serial
*/
{
.vendor = PCI_VENDOR_ID_NETMOS,
quirk_id_matches(quirk->device, dev->device) &&
quirk_id_matches(quirk->subvendor, dev->subsystem_vendor) &&
quirk_id_matches(quirk->subdevice, dev->subsystem_device))
- break;
+ break;
return quirk;
}
-static _INLINE_ int
-get_pci_irq(struct pci_dev *dev, struct pciserial_board *board)
+static inline int get_pci_irq(struct pci_dev *dev,
+ struct pciserial_board *board)
{
if (board->flags & FL_NOIRQ)
return 0;
* driver_data member.
*
* The makeup of these names are:
- * pbn_bn{_bt}_n_baud
+ * pbn_bn{_bt}_n_baud{_offsetinhex}
*
- * bn = PCI BAR number
- * bt = Index using PCI BARs
- * n = number of serial ports
- * baud = baud rate
+ * bn = PCI BAR number
+ * bt = Index using PCI BARs
+ * n = number of serial ports
+ * baud = baud rate
+ * offsetinhex = offset for each sequential port (in hex)
*
- * This table is sorted by (in order): baud, bt, bn, n.
+ * This table is sorted by (in order): bn, bt, baud, offsetindex, n.
*
* Please note: in theory if n = 1, _bt infix should make no difference.
* ie, pbn_b0_1_115200 is the same as pbn_b0_bt_1_115200
pbn_b0_2_115200,
pbn_b0_4_115200,
pbn_b0_5_115200,
+ pbn_b0_8_115200,
pbn_b0_1_921600,
pbn_b0_2_921600,
pbn_b0_4_1152000,
+ pbn_b0_2_1843200,
+ pbn_b0_4_1843200,
+
+ pbn_b0_2_1843200_200,
+ pbn_b0_4_1843200_200,
+ pbn_b0_8_1843200_200,
+
pbn_b0_bt_1_115200,
pbn_b0_bt_2_115200,
pbn_b0_bt_8_115200,
pbn_b1_4_921600,
pbn_b1_8_921600,
+ pbn_b1_2_1250000,
+
+ pbn_b1_bt_1_115200,
pbn_b1_bt_2_921600,
pbn_b1_1_1382400,
pbn_b1_8_1382400,
pbn_b2_1_115200,
+ pbn_b2_2_115200,
+ pbn_b2_4_115200,
pbn_b2_8_115200,
pbn_b2_1_460800,
pbn_b2_bt_2_921600,
pbn_b2_bt_4_921600,
+ pbn_b3_2_115200,
pbn_b3_4_115200,
pbn_b3_8_115200,
pbn_panacom,
pbn_panacom2,
pbn_panacom4,
+ pbn_exsys_4055,
pbn_plx_romulus,
pbn_oxsemi,
pbn_intel_i960,
pbn_sgi_ioc3,
- pbn_nec_nile4,
pbn_computone_4,
pbn_computone_6,
pbn_computone_8,
pbn_exar_XR17C152,
pbn_exar_XR17C154,
pbn_exar_XR17C158,
+ pbn_pasemi_1682M,
};
/*
.base_baud = 115200,
.uart_offset = 8,
},
-
+ [pbn_b0_8_115200] = {
+ .flags = FL_BASE0,
+ .num_ports = 8,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
[pbn_b0_1_921600] = {
.flags = FL_BASE0,
.num_ports = 1,
.uart_offset = 8,
},
+ [pbn_b0_2_1843200] = {
+ .flags = FL_BASE0,
+ .num_ports = 2,
+ .base_baud = 1843200,
+ .uart_offset = 8,
+ },
+ [pbn_b0_4_1843200] = {
+ .flags = FL_BASE0,
+ .num_ports = 4,
+ .base_baud = 1843200,
+ .uart_offset = 8,
+ },
+
+ [pbn_b0_2_1843200_200] = {
+ .flags = FL_BASE0,
+ .num_ports = 2,
+ .base_baud = 1843200,
+ .uart_offset = 0x200,
+ },
+ [pbn_b0_4_1843200_200] = {
+ .flags = FL_BASE0,
+ .num_ports = 4,
+ .base_baud = 1843200,
+ .uart_offset = 0x200,
+ },
+ [pbn_b0_8_1843200_200] = {
+ .flags = FL_BASE0,
+ .num_ports = 8,
+ .base_baud = 1843200,
+ .uart_offset = 0x200,
+ },
+
[pbn_b0_bt_1_115200] = {
.flags = FL_BASE0|FL_BASE_BARS,
.num_ports = 1,
.base_baud = 921600,
.uart_offset = 8,
},
+ [pbn_b1_2_1250000] = {
+ .flags = FL_BASE1,
+ .num_ports = 2,
+ .base_baud = 1250000,
+ .uart_offset = 8,
+ },
+
+ [pbn_b1_bt_1_115200] = {
+ .flags = FL_BASE1|FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
[pbn_b1_bt_2_921600] = {
.flags = FL_BASE1|FL_BASE_BARS,
.base_baud = 115200,
.uart_offset = 8,
},
+ [pbn_b2_2_115200] = {
+ .flags = FL_BASE2,
+ .num_ports = 2,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [pbn_b2_4_115200] = {
+ .flags = FL_BASE2,
+ .num_ports = 4,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
[pbn_b2_8_115200] = {
.flags = FL_BASE2,
.num_ports = 8,
.uart_offset = 8,
},
+ [pbn_b3_2_115200] = {
+ .flags = FL_BASE3,
+ .num_ports = 2,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
[pbn_b3_4_115200] = {
.flags = FL_BASE3,
.num_ports = 4,
.reg_shift = 7,
},
+ [pbn_exsys_4055] = {
+ .flags = FL_BASE2,
+ .num_ports = 4,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+
/* I think this entry is broken - the first_offset looks wrong --rmk */
[pbn_plx_romulus] = {
.flags = FL_BASE2,
},
/*
- * NEC Vrc-5074 (Nile 4) builtin UART.
- */
- [pbn_nec_nile4] = {
- .flags = FL_BASE0,
- .num_ports = 1,
- .base_baud = 520833,
- .uart_offset = 8 << 3,
- .reg_shift = 3,
- .first_offset = 0x300,
- },
-
- /*
* Computone - uses IOMEM.
*/
[pbn_computone_4] = {
.base_baud = 921600,
.uart_offset = 0x200,
},
+ /*
+ * PA Semi PWRficient PA6T-1682M on-chip UART
+ */
+ [pbn_pasemi_1682M] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 8333333,
+ },
+};
+
+static const struct pci_device_id softmodem_blacklist[] = {
+ { PCI_VDEVICE(AL, 0x5457), }, /* ALi Corporation M5457 AC'97 Modem */
};
/*
static int __devinit
serial_pci_guess_board(struct pci_dev *dev, struct pciserial_board *board)
{
+ const struct pci_device_id *blacklist;
int num_iomem, num_port, first_port = -1, i;
-
+
/*
* If it is not a communications device or the programming
* interface is greater than 6, give up.
*
* (Should we try to make guesses for multiport serial devices
- * later?)
+ * later?)
*/
if ((((dev->class >> 8) != PCI_CLASS_COMMUNICATION_SERIAL) &&
((dev->class >> 8) != PCI_CLASS_COMMUNICATION_MODEM)) ||
(dev->class & 0xff) > 6)
return -ENODEV;
+ /*
+ * Do not access blacklisted devices that are known not to
+ * feature serial ports.
+ */
+ for (blacklist = softmodem_blacklist;
+ blacklist < softmodem_blacklist + ARRAY_SIZE(softmodem_blacklist);
+ blacklist++) {
+ if (dev->vendor == blacklist->vendor &&
+ dev->device == blacklist->device)
+ return -ENODEV;
+ }
+
num_iomem = num_port = 0;
for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
if (pci_resource_flags(dev, i) & IORESOURCE_IO) {
nr_ports = rc;
}
- priv = kmalloc(sizeof(struct serial_private) +
+ priv = kzalloc(sizeof(struct serial_private) +
sizeof(unsigned int) * nr_ports,
GFP_KERNEL);
if (!priv) {
goto err_deinit;
}
- memset(priv, 0, sizeof(struct serial_private) +
- sizeof(unsigned int) * nr_ports);
-
priv->dev = dev;
priv->quirk = quirk;
break;
#ifdef SERIAL_DEBUG_PCI
- printk("Setup PCI port: port %x, irq %d, type %d\n",
+ printk(KERN_DEBUG "Setup PCI port: port %x, irq %d, type %d\n",
serial_port.iobase, serial_port.irq, serial_port.iotype);
#endif
-
+
priv->line[i] = serial8250_register_port(&serial_port);
if (priv->line[i] < 0) {
printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), priv->line[i]);
break;
}
}
-
priv->nr = i;
-
return priv;
- err_deinit:
+err_deinit:
if (quirk->exit)
quirk->exit(dev);
- err_out:
+err_out:
return priv;
}
EXPORT_SYMBOL_GPL(pciserial_init_ports);
pci_disable_device(dev);
}
+#ifdef CONFIG_PM
static int pciserial_suspend_one(struct pci_dev *dev, pm_message_t state)
{
struct serial_private *priv = pci_get_drvdata(dev);
static int pciserial_resume_one(struct pci_dev *dev)
{
+ int err;
struct serial_private *priv = pci_get_drvdata(dev);
pci_set_power_state(dev, PCI_D0);
/*
* The device may have been disabled. Re-enable it.
*/
- pci_enable_device(dev);
-
+ err = pci_enable_device(dev);
+ /* FIXME: We cannot simply error out here */
+ if (err)
+ printk(KERN_ERR "pciserial: Unable to re-enable ports, trying to continue.\n");
pciserial_resume_ports(priv);
}
return 0;
}
+#endif
static struct pci_device_id serial_pci_tbl[] = {
{ PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH041101V1, 0, 0,
pbn_b1_4_921600 },
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_20MHZ, 0, 0,
+ pbn_b1_2_1250000 },
+ { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_TITAN_2, 0, 0,
+ pbn_b0_2_1843200 },
+ { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_TITAN_4, 0, 0,
+ pbn_b0_4_1843200 },
+ { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
+ PCI_VENDOR_ID_AFAVLAB,
+ PCI_SUBDEVICE_ID_AFAVLAB_P061, 0, 0,
+ pbn_b0_4_1152000 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_232, 0, 0,
+ pbn_b0_2_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_232, 0, 0,
+ pbn_b0_4_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_232, 0, 0,
+ pbn_b0_8_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_1_1, 0, 0,
+ pbn_b0_2_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_2, 0, 0,
+ pbn_b0_4_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4, 0, 0,
+ pbn_b0_8_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2, 0, 0,
+ pbn_b0_2_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4, 0, 0,
+ pbn_b0_4_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8, 0, 0,
+ pbn_b0_8_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_485, 0, 0,
+ pbn_b0_2_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_485, 0, 0,
+ pbn_b0_4_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_485, 0, 0,
+ pbn_b0_8_1843200_200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_U530,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_1_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM2,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM422,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM232,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_2_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_COMM4,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_bt_4_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_COMM8,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_8_115200 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_UCOMM8,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
/*
* VScom SPCOM800, from sl@s.pl
*/
- { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_SPCOM800,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_SPCOM800,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_8_921600 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_1077,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_4_921600 },
+ /* Unknown card - subdevice 0x1584 */
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
+ PCI_VENDOR_ID_PLX,
+ PCI_SUBDEVICE_ID_UNKNOWN_0x1584, 0, 0,
+ pbn_b0_4_115200 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_KEYSPAN,
PCI_SUBDEVICE_ID_KEYSPAN_SX2, 0, 0,
{ PCI_VENDOR_ID_PANACOM, PCI_DEVICE_ID_PANACOM_DUALMODEM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_panacom2 },
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
+ PCI_VENDOR_ID_ESDGMBH,
+ PCI_DEVICE_ID_ESDGMBH_CPCIASIO4, 0, 0,
+ pbn_b2_4_115200 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
- PCI_SUBDEVICE_ID_CHASE_PCIFAST4, 0, 0,
+ PCI_SUBDEVICE_ID_CHASE_PCIFAST4, 0, 0,
pbn_b2_4_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
- PCI_SUBDEVICE_ID_CHASE_PCIFAST8, 0, 0,
+ PCI_SUBDEVICE_ID_CHASE_PCIFAST8, 0, 0,
pbn_b2_8_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
- PCI_SUBDEVICE_ID_CHASE_PCIFAST16, 0, 0,
+ PCI_SUBDEVICE_ID_CHASE_PCIFAST16, 0, 0,
pbn_b2_16_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIFAST,
- PCI_SUBDEVICE_ID_CHASE_PCIFAST16FMC, 0, 0,
+ PCI_SUBDEVICE_ID_CHASE_PCIFAST16FMC, 0, 0,
pbn_b2_16_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIRAS,
- PCI_SUBDEVICE_ID_CHASE_PCIRAS4, 0, 0,
+ PCI_SUBDEVICE_ID_CHASE_PCIRAS4, 0, 0,
pbn_b2_4_460800 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_CHASE_PCIRAS,
- PCI_SUBDEVICE_ID_CHASE_PCIRAS8, 0, 0,
+ PCI_SUBDEVICE_ID_CHASE_PCIRAS8, 0, 0,
pbn_b2_8_460800 },
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
+ PCI_SUBVENDOR_ID_EXSYS,
+ PCI_SUBDEVICE_ID_EXSYS_4055, 0, 0,
+ pbn_exsys_4055 },
/*
* Megawolf Romulus PCI Serial Card, from Mike Hudson
* (Exoray@isys.ca)
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
{ PCI_VENDOR_ID_SPECIALIX, PCI_DEVICE_ID_OXSEMI_16PCI954,
- PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4, 0, 0,
+ PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4,
+ 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
- PCI_SUBVENDOR_ID_SIIG, PCI_SUBDEVICE_ID_SIIG_QUARTET_SERIAL, 0, 0,
+ PCI_SUBVENDOR_ID_SIIG, PCI_SUBDEVICE_ID_SIIG_QUARTET_SERIAL,
+ 0, 0,
pbn_b0_4_1152000 },
/*
* Digitan DS560-558, from jimd@esoft.com
*/
{ PCI_VENDOR_ID_ATT, PCI_DEVICE_ID_ATT_VENUS_MODEM,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_1_115200 },
/*
* The 400L and 800L have a custom setup quirk.
*/
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_100,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_200,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_2_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_400,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_800B,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_100L,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_4S_20x_850,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_4_921600 },
+ { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_8S_20x_550,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_8_921600 },
+ { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_8S_20x_650,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_8_921600 },
+ { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_8S_20x_850,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_bt_8_921600 },
/*
* Computone devices submitted by Doug McNash dmcnash@computone.com
pbn_b0_bt_1_460800 },
/*
+ * Korenix Jetcard F0/F1 cards (JC1204, JC1208, JC1404, JC1408).
+ * Cards are identified by their subsystem vendor IDs, which
+ * (in hex) match the model number.
+ *
+ * Note that JC140x are RS422/485 cards which require ox950
+ * ACR = 0x10, and as such are not currently fully supported.
+ */
+ { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0,
+ 0x1204, 0x0004, 0, 0,
+ pbn_b0_4_921600 },
+ { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0,
+ 0x1208, 0x0004, 0, 0,
+ pbn_b0_4_921600 },
+/* { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0,
+ 0x1402, 0x0002, 0, 0,
+ pbn_b0_2_921600 }, */
+/* { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0,
+ 0x1404, 0x0004, 0, 0,
+ pbn_b0_4_921600 }, */
+ { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF1,
+ 0x1208, 0x0004, 0, 0,
+ pbn_b0_4_921600 },
+
+ /*
* Dell Remote Access Card 4 - Tim_T_Murphy@Dell.com
*/
{ PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_RAC4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b2_1_115200 },
- /*
- * NEC Vrc-5074 (Nile 4) builtin UART.
- */
- { PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_NILE4,
+ { PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_nec_nile4 },
-
+ pbn_b3_2_115200 },
{ PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b3_4_115200 },
{ PCI_VENDOR_ID_TOPIC, PCI_DEVICE_ID_TOPIC_TP560,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_1_115200 },
+ /*
+ * ITE
+ */
+ { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0,
+ pbn_b1_bt_1_115200 },
+
+ /*
+ * IntaShield IS-200
+ */
+ { PCI_VENDOR_ID_INTASHIELD, PCI_DEVICE_ID_INTASHIELD_IS200,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, /* 135a.0811 */
+ pbn_b2_2_115200 },
+ /*
+ * IntaShield IS-400
+ */
+ { PCI_VENDOR_ID_INTASHIELD, PCI_DEVICE_ID_INTASHIELD_IS400,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, /* 135a.0dc0 */
+ pbn_b2_4_115200 },
+ /*
+ * Perle PCI-RAS cards
+ */
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
+ PCI_SUBVENDOR_ID_PERLE, PCI_SUBDEVICE_ID_PCI_RAS4,
+ 0, 0, pbn_b2_4_921600 },
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
+ PCI_SUBVENDOR_ID_PERLE, PCI_SUBDEVICE_ID_PCI_RAS8,
+ 0, 0, pbn_b2_8_921600 },
+
+ /*
+ * Mainpine series cards: Fairly standard layout but fools
+ * parts of the autodetect in some cases and uses otherwise
+ * unmatched communications subclasses in the PCI Express case
+ */
+
+ { /* RockForceDUO */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x0200,
+ 0, 0, pbn_b0_2_115200 },
+ { /* RockForceQUATRO */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x0300,
+ 0, 0, pbn_b0_4_115200 },
+ { /* RockForceDUO+ */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x0400,
+ 0, 0, pbn_b0_2_115200 },
+ { /* RockForceQUATRO+ */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x0500,
+ 0, 0, pbn_b0_4_115200 },
+ { /* RockForce+ */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x0600,
+ 0, 0, pbn_b0_2_115200 },
+ { /* RockForce+ */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x0700,
+ 0, 0, pbn_b0_4_115200 },
+ { /* RockForceOCTO+ */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x0800,
+ 0, 0, pbn_b0_8_115200 },
+ { /* RockForceDUO+ */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x0C00,
+ 0, 0, pbn_b0_2_115200 },
+ { /* RockForceQUARTRO+ */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x0D00,
+ 0, 0, pbn_b0_4_115200 },
+ { /* RockForceOCTO+ */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x1D00,
+ 0, 0, pbn_b0_8_115200 },
+ { /* RockForceD1 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x2000,
+ 0, 0, pbn_b0_1_115200 },
+ { /* RockForceF1 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x2100,
+ 0, 0, pbn_b0_1_115200 },
+ { /* RockForceD2 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x2200,
+ 0, 0, pbn_b0_2_115200 },
+ { /* RockForceF2 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x2300,
+ 0, 0, pbn_b0_2_115200 },
+ { /* RockForceD4 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x2400,
+ 0, 0, pbn_b0_4_115200 },
+ { /* RockForceF4 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x2500,
+ 0, 0, pbn_b0_4_115200 },
+ { /* RockForceD8 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x2600,
+ 0, 0, pbn_b0_8_115200 },
+ { /* RockForceF8 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x2700,
+ 0, 0, pbn_b0_8_115200 },
+ { /* IQ Express D1 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x3000,
+ 0, 0, pbn_b0_1_115200 },
+ { /* IQ Express F1 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x3100,
+ 0, 0, pbn_b0_1_115200 },
+ { /* IQ Express D2 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x3200,
+ 0, 0, pbn_b0_2_115200 },
+ { /* IQ Express F2 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x3300,
+ 0, 0, pbn_b0_2_115200 },
+ { /* IQ Express D4 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x3400,
+ 0, 0, pbn_b0_4_115200 },
+ { /* IQ Express F4 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x3500,
+ 0, 0, pbn_b0_4_115200 },
+ { /* IQ Express D8 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x3C00,
+ 0, 0, pbn_b0_8_115200 },
+ { /* IQ Express F8 */
+ PCI_VENDOR_ID_MAINPINE, PCI_DEVICE_ID_MAINPINE_PBRIDGE,
+ PCI_VENDOR_ID_MAINPINE, 0x3D00,
+ 0, 0, pbn_b0_8_115200 },
+
+
+ /*
+ * PA Semi PA6T-1682M on-chip UART
+ */
+ { PCI_VENDOR_ID_PASEMI, 0xa004,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_pasemi_1682M },
+
+ /*
+ * ADDI-DATA GmbH communication cards <info@addi-data.com>
+ */
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7500,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_4_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7420,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_2_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7300,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_1_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA_OLD,
+ PCI_DEVICE_ID_ADDIDATA_APCI7800,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b1_8_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7500_2,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_4_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7420_2,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_2_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7300_2,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_1_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7500_3,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_4_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7420_3,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_2_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7300_3,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_1_115200 },
+
+ { PCI_VENDOR_ID_ADDIDATA,
+ PCI_DEVICE_ID_ADDIDATA_APCI7800_3,
+ PCI_ANY_ID,
+ PCI_ANY_ID,
+ 0,
+ 0,
+ pbn_b0_8_115200 },
/*
* These entries match devices with class COMMUNICATION_SERIAL,
.name = "serial",
.probe = pciserial_init_one,
.remove = __devexit_p(pciserial_remove_one),
+#ifdef CONFIG_PM
.suspend = pciserial_suspend_one,
.resume = pciserial_resume_one,
+#endif
.id_table = serial_pci_tbl,
};
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff