unsigned char mcr;
unsigned char mcr_mask; /* mask of user bits */
unsigned char mcr_force; /* mask of forced bits */
- unsigned char lsr_break_flag;
+
+ /*
+ * Some bits in registers are cleared on a read, so they must
+ * be saved whenever the register is read but the bits will not
+ * be immediately processed.
+ */
+#define LSR_SAVE_FLAGS UART_LSR_BRK_ERROR_BITS
+ unsigned char lsr_saved_flags;
+#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
+ unsigned char msr_saved_flags;
/*
* We provide a per-port pm hook.
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_UUE,
},
+ [PORT_RM9000] = {
+ .name = "RM9000",
+ .fifo_size = 16,
+ .tx_loadsz = 16,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO,
+ },
};
-#ifdef CONFIG_SERIAL_8250_AU1X00
+#if defined (CONFIG_SERIAL_8250_AU1X00)
/* Au1x00 UART hardware has a weird register layout */
static const u8 au_io_in_map[] = {
return au_io_out_map[offset];
}
+#elif defined(CONFIG_SERIAL_8250_RM9K)
+
+static const u8
+ regmap_in[8] = {
+ [UART_RX] = 0x00,
+ [UART_IER] = 0x0c,
+ [UART_IIR] = 0x14,
+ [UART_LCR] = 0x1c,
+ [UART_MCR] = 0x20,
+ [UART_LSR] = 0x24,
+ [UART_MSR] = 0x28,
+ [UART_SCR] = 0x2c
+ },
+ regmap_out[8] = {
+ [UART_TX] = 0x04,
+ [UART_IER] = 0x0c,
+ [UART_FCR] = 0x18,
+ [UART_LCR] = 0x1c,
+ [UART_MCR] = 0x20,
+ [UART_LSR] = 0x24,
+ [UART_MSR] = 0x28,
+ [UART_SCR] = 0x2c
+ };
+
+static inline int map_8250_in_reg(struct uart_8250_port *up, int offset)
+{
+ if (up->port.iotype != UPIO_RM9000)
+ return offset;
+ return regmap_in[offset];
+}
+
+static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
+{
+ if (up->port.iotype != UPIO_RM9000)
+ return offset;
+ return regmap_out[offset];
+}
+
#else
/* sane hardware needs no mapping */
return inb(up->port.iobase + 1);
case UPIO_MEM:
+ case UPIO_DWAPB:
return readb(up->port.membase + offset);
+ case UPIO_RM9000:
case UPIO_MEM32:
return readl(up->port.membase + offset);
static void
serial_out(struct uart_8250_port *up, int offset, int value)
{
+ /* Save the offset before it's remapped */
+ int save_offset = offset;
offset = map_8250_out_reg(up, offset) << up->port.regshift;
switch (up->port.iotype) {
writeb(value, up->port.membase + offset);
break;
+ case UPIO_RM9000:
case UPIO_MEM32:
writel(value, up->port.membase + offset);
break;
writeb(value, up->port.membase + offset);
break;
+ case UPIO_DWAPB:
+ /* Save the LCR value so it can be re-written when a
+ * Busy Detect interrupt occurs. */
+ if (save_offset == UART_LCR)
+ up->lcr = value;
+ writeb(value, up->port.membase + offset);
+ /* Read the IER to ensure any interrupt is cleared before
+ * returning from ISR. */
+ if (save_offset == UART_TX || save_offset == UART_IER)
+ value = serial_in(up, UART_IER);
+ break;
+
default:
outb(value, up->port.iobase + offset);
}
}
+static void
+serial_out_sync(struct uart_8250_port *up, int offset, int value)
+{
+ switch (up->port.iotype) {
+ case UPIO_MEM:
+ case UPIO_MEM32:
+#ifdef CONFIG_SERIAL_8250_AU1X00
+ case UPIO_AU:
+#endif
+ case UPIO_DWAPB:
+ serial_out(up, offset, value);
+ serial_in(up, UART_LCR); /* safe, no side-effects */
+ break;
+ default:
+ serial_out(up, offset, value);
+ }
+}
+
/*
* We used to support using pause I/O for certain machines. We
* haven't supported this for a while, but just in case it's badly
serial_outp(up, UART_DLM, value >> 8 & 0xff);
}
-#ifdef CONFIG_SERIAL_8250_AU1X00
+#if defined(CONFIG_SERIAL_8250_AU1X00)
/* Au1x00 haven't got a standard divisor latch */
static int serial_dl_read(struct uart_8250_port *up)
{
else
_serial_dl_write(up, value);
}
+#elif defined(CONFIG_SERIAL_8250_RM9K)
+static int serial_dl_read(struct uart_8250_port *up)
+{
+ return (up->port.iotype == UPIO_RM9000) ?
+ (((__raw_readl(up->port.membase + 0x10) << 8) |
+ (__raw_readl(up->port.membase + 0x08) & 0xff)) & 0xffff) :
+ _serial_dl_read(up);
+}
+
+static void serial_dl_write(struct uart_8250_port *up, int value)
+{
+ if (up->port.iotype == UPIO_RM9000) {
+ __raw_writel(value, up->port.membase + 0x08);
+ __raw_writel(value >> 8, up->port.membase + 0x10);
+ } else {
+ _serial_dl_write(up, value);
+ }
+}
#else
#define serial_dl_read(up) _serial_dl_read(up)
#define serial_dl_write(up, value) _serial_dl_write(up, value)
* its clones. (We treat the broken original StarTech 16650 V1 as a
* 16550, and why not? Startech doesn't seem to even acknowledge its
* existence.)
- *
+ *
* What evil have men's minds wrought...
*/
static void autoconfig_has_efr(struct uart_8250_port *up)
up->bugs |= UART_BUG_QUOT;
return;
}
-
+
/*
* We check for a XR16C850 by setting DLL and DLM to 0, and then
* reading back DLL and DLM. The chip type depends on the DLM
quot = serial_dl_read(up);
quot <<= 3;
- status1 = serial_in(up, 0x04); /* EXCR1 */
+ status1 = serial_in(up, 0x04); /* EXCR2 */
status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
status1 |= 0x10; /* 1.625 divisor for baud_base --> 921600 */
serial_outp(up, 0x04, status1);
-
+
serial_dl_write(up, quot);
serial_outp(up, UART_LCR, 0);
* be frobbing the chips IRQ enable register to see if it exists.
*/
spin_lock_irqsave(&up->port.lock, flags);
-// save_flags(flags); cli();
up->capabilities = 0;
up->bugs = 0;
/*
* Do a simple existence test first; if we fail this,
* there's no point trying anything else.
- *
+ *
* 0x80 is used as a nonsense port to prevent against
* false positives due to ISA bus float. The
* assumption is that 0x80 is a non-existent port;
#ifdef __i386__
outb(0xff, 0x080);
#endif
- scratch2 = serial_inp(up, UART_IER);
+ /*
+ * Mask out IER[7:4] bits for test as some UARTs (e.g. TL
+ * 16C754B) allow only to modify them if an EFR bit is set.
+ */
+ scratch2 = serial_inp(up, UART_IER) & 0x0f;
serial_outp(up, UART_IER, 0x0F);
#ifdef __i386__
outb(0, 0x080);
#endif
- scratch3 = serial_inp(up, UART_IER);
+ scratch3 = serial_inp(up, UART_IER) & 0x0f;
serial_outp(up, UART_IER, scratch);
if (scratch2 != 0 || scratch3 != 0x0F) {
/*
save_mcr = serial_in(up, UART_MCR);
save_lcr = serial_in(up, UART_LCR);
- /*
+ /*
* Check to see if a UART is really there. Certain broken
* internal modems based on the Rockwell chipset fail this
* test, because they apparently don't implement the loopback
#endif
serial_outp(up, UART_MCR, save_mcr);
serial8250_clear_fifos(up);
- (void)serial_in(up, UART_RX);
+ serial_in(up, UART_RX);
if (up->capabilities & UART_CAP_UUE)
serial_outp(up, UART_IER, UART_IER_UUE);
else
serial_outp(up, UART_IER, 0);
- out:
+ out:
spin_unlock_irqrestore(&up->port.lock, flags);
-// restore_flags(flags);
DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name);
}
save_mcr = serial_inp(up, UART_MCR);
save_ier = serial_inp(up, UART_IER);
serial_outp(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
-
+
irqs = probe_irq_on();
serial_outp(up, UART_MCR, 0);
- udelay (10);
- if (up->port.flags & UPF_FOURPORT) {
+ udelay(10);
+ if (up->port.flags & UPF_FOURPORT) {
serial_outp(up, UART_MCR,
UART_MCR_DTR | UART_MCR_RTS);
} else {
(void)serial_inp(up, UART_IIR);
(void)serial_inp(up, UART_MSR);
serial_outp(up, UART_TX, 0xFF);
- udelay (20);
+ udelay(20);
irq = probe_irq_off(irqs);
serial_outp(up, UART_MCR, save_mcr);
if (up->bugs & UART_BUG_TXEN) {
unsigned char lsr, iir;
lsr = serial_in(up, UART_LSR);
- iir = serial_in(up, UART_IIR);
- if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
+ up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+ iir = serial_in(up, UART_IIR) & 0x0f;
+ if ((up->port.type == PORT_RM9000) ?
+ (lsr & UART_LSR_THRE &&
+ (iir == UART_IIR_NO_INT || iir == UART_IIR_THRI)) :
+ (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT))
transmit_chars(up);
}
}
}
static void
-receive_chars(struct uart_8250_port *up, int *status, struct pt_regs *regs)
+receive_chars(struct uart_8250_port *up, unsigned int *status)
{
struct tty_struct *tty = up->port.info->tty;
unsigned char ch, lsr = *status;
flag = TTY_NORMAL;
up->port.icount.rx++;
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- /*
- * Recover the break flag from console xmit
- */
- if (up->port.line == up->port.cons->index) {
- lsr |= up->lsr_break_flag;
- up->lsr_break_flag = 0;
- }
-#endif
+ lsr |= up->lsr_saved_flags;
+ up->lsr_saved_flags = 0;
- if (unlikely(lsr & (UART_LSR_BI | UART_LSR_PE |
- UART_LSR_FE | UART_LSR_OE))) {
+ if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) {
/*
* For statistics only
*/
else if (lsr & UART_LSR_FE)
flag = TTY_FRAME;
}
- if (uart_handle_sysrq_char(&up->port, ch, regs))
+ if (uart_handle_sysrq_char(&up->port, ch))
goto ignore_char;
uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
- ignore_char:
+ignore_char:
lsr = serial_inp(up, UART_LSR);
} while ((lsr & UART_LSR_DR) && (max_count-- > 0));
spin_unlock(&up->port.lock);
{
unsigned int status = serial_in(up, UART_MSR);
- if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI) {
+ status |= up->msr_saved_flags;
+ up->msr_saved_flags = 0;
+ if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
+ up->port.info != NULL) {
if (status & UART_MSR_TERI)
up->port.icount.rng++;
if (status & UART_MSR_DDSR)
* This handles the interrupt from one port.
*/
static inline void
-serial8250_handle_port(struct uart_8250_port *up, struct pt_regs *regs)
+serial8250_handle_port(struct uart_8250_port *up)
{
unsigned int status;
+ unsigned long flags;
- spin_lock(&up->port.lock);
+ spin_lock_irqsave(&up->port.lock, flags);
status = serial_inp(up, UART_LSR);
DEBUG_INTR("status = %x...", status);
if (status & UART_LSR_DR)
- receive_chars(up, &status, regs);
+ receive_chars(up, &status);
check_modem_status(up);
if (status & UART_LSR_THRE)
transmit_chars(up);
- spin_unlock(&up->port.lock);
+ spin_unlock_irqrestore(&up->port.lock, flags);
}
/*
* This means we need to loop through all ports. checking that they
* don't have an interrupt pending.
*/
-static irqreturn_t serial8250_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+static irqreturn_t serial8250_interrupt(int irq, void *dev_id)
{
struct irq_info *i = dev_id;
struct list_head *l, *end = NULL;
iir = serial_in(up, UART_IIR);
if (!(iir & UART_IIR_NO_INT)) {
- serial8250_handle_port(up, regs);
+ serial8250_handle_port(up);
+
+ handled = 1;
+
+ end = NULL;
+ } else if (up->port.iotype == UPIO_DWAPB &&
+ (iir & UART_IIR_BUSY) == UART_IIR_BUSY) {
+ /* The DesignWare APB UART has an Busy Detect (0x07)
+ * interrupt meaning an LCR write attempt occured while the
+ * UART was busy. The interrupt must be cleared by reading
+ * the UART status register (USR) and the LCR re-written. */
+ unsigned int status;
+ status = *(volatile u32 *)up->port.private_data;
+ serial_out(up, UART_LCR, up->lcr);
handled = 1;
serial_do_unlink(i, up);
}
+/* Base timer interval for polling */
+static inline int poll_timeout(int timeout)
+{
+ return timeout > 6 ? (timeout / 2 - 2) : 1;
+}
+
/*
* This function is used to handle ports that do not have an
* interrupt. This doesn't work very well for 16450's, but gives
static void serial8250_timeout(unsigned long data)
{
struct uart_8250_port *up = (struct uart_8250_port *)data;
- unsigned int timeout;
unsigned int iir;
iir = serial_in(up, UART_IIR);
if (!(iir & UART_IIR_NO_INT))
- serial8250_handle_port(up, NULL);
+ serial8250_handle_port(up);
+ mod_timer(&up->timer, jiffies + poll_timeout(up->port.timeout));
+}
+
+static void serial8250_backup_timeout(unsigned long data)
+{
+ struct uart_8250_port *up = (struct uart_8250_port *)data;
+ unsigned int iir, ier = 0, lsr;
+ unsigned long flags;
+
+ /*
+ * Must disable interrupts or else we risk racing with the interrupt
+ * based handler.
+ */
+ if (is_real_interrupt(up->port.irq)) {
+ ier = serial_in(up, UART_IER);
+ serial_out(up, UART_IER, 0);
+ }
+
+ iir = serial_in(up, UART_IIR);
+
+ /*
+ * This should be a safe test for anyone who doesn't trust the
+ * IIR bits on their UART, but it's specifically designed for
+ * the "Diva" UART used on the management processor on many HP
+ * ia64 and parisc boxes.
+ */
+ spin_lock_irqsave(&up->port.lock, flags);
+ lsr = serial_in(up, UART_LSR);
+ up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+ spin_unlock_irqrestore(&up->port.lock, flags);
+ if ((iir & UART_IIR_NO_INT) && (up->ier & UART_IER_THRI) &&
+ (!uart_circ_empty(&up->port.info->xmit) || up->port.x_char) &&
+ (lsr & UART_LSR_THRE)) {
+ iir &= ~(UART_IIR_ID | UART_IIR_NO_INT);
+ iir |= UART_IIR_THRI;
+ }
+
+ if (!(iir & UART_IIR_NO_INT))
+ serial8250_handle_port(up);
+
+ if (is_real_interrupt(up->port.irq))
+ serial_out(up, UART_IER, ier);
- timeout = up->port.timeout;
- timeout = timeout > 6 ? (timeout / 2 - 2) : 1;
- mod_timer(&up->timer, jiffies + timeout);
+ /* Standard timer interval plus 0.2s to keep the port running */
+ mod_timer(&up->timer,
+ jiffies + poll_timeout(up->port.timeout) + HZ / 5);
}
static unsigned int serial8250_tx_empty(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned long flags;
- unsigned int ret;
+ unsigned int lsr;
spin_lock_irqsave(&up->port.lock, flags);
- ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
+ lsr = serial_in(up, UART_LSR);
+ up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
spin_unlock_irqrestore(&up->port.lock, flags);
- return ret;
+ return lsr & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
}
static unsigned int serial8250_get_mctrl(struct uart_port *port)
spin_unlock_irqrestore(&up->port.lock, flags);
}
+#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
+
+/*
+ * Wait for transmitter & holding register to empty
+ */
+static inline void wait_for_xmitr(struct uart_8250_port *up, int bits)
+{
+ unsigned int status, tmout = 10000;
+
+ /* Wait up to 10ms for the character(s) to be sent. */
+ do {
+ status = serial_in(up, UART_LSR);
+
+ up->lsr_saved_flags |= status & LSR_SAVE_FLAGS;
+
+ if (--tmout == 0)
+ break;
+ udelay(1);
+ } while ((status & bits) != bits);
+
+ /* Wait up to 1s for flow control if necessary */
+ if (up->port.flags & UPF_CONS_FLOW) {
+ unsigned int tmout;
+ for (tmout = 1000000; tmout; tmout--) {
+ unsigned int msr = serial_in(up, UART_MSR);
+ up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
+ if (msr & UART_MSR_CTS)
+ break;
+ udelay(1);
+ touch_nmi_watchdog();
+ }
+ }
+}
+
static int serial8250_startup(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
serial_outp(up, UART_LCR, 0);
}
+ if (is_real_interrupt(up->port.irq)) {
+ /*
+ * Test for UARTs that do not reassert THRE when the
+ * transmitter is idle and the interrupt has already
+ * been cleared. Real 16550s should always reassert
+ * this interrupt whenever the transmitter is idle and
+ * the interrupt is enabled. Delays are necessary to
+ * allow register changes to become visible.
+ */
+ spin_lock_irqsave(&up->port.lock, flags);
+
+ wait_for_xmitr(up, UART_LSR_THRE);
+ serial_out_sync(up, UART_IER, UART_IER_THRI);
+ udelay(1); /* allow THRE to set */
+ serial_in(up, UART_IIR);
+ serial_out(up, UART_IER, 0);
+ serial_out_sync(up, UART_IER, UART_IER_THRI);
+ udelay(1); /* allow a working UART time to re-assert THRE */
+ iir = serial_in(up, UART_IIR);
+ serial_out(up, UART_IER, 0);
+
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ /*
+ * If the interrupt is not reasserted, setup a timer to
+ * kick the UART on a regular basis.
+ */
+ if (iir & UART_IIR_NO_INT) {
+ pr_debug("ttyS%d - using backup timer\n", port->line);
+ up->timer.function = serial8250_backup_timeout;
+ up->timer.data = (unsigned long)up;
+ mod_timer(&up->timer, jiffies +
+ poll_timeout(up->port.timeout) + HZ / 5);
+ }
+ }
+
/*
* If the "interrupt" for this port doesn't correspond with any
* hardware interrupt, we use a timer-based system. The original
* driver used to do this with IRQ0.
*/
if (!is_real_interrupt(up->port.irq)) {
- unsigned int timeout = up->port.timeout;
-
- timeout = timeout > 6 ? (timeout / 2 - 2) : 1;
-
up->timer.data = (unsigned long)up;
- mod_timer(&up->timer, jiffies + timeout);
+ mod_timer(&up->timer, jiffies + poll_timeout(up->port.timeout));
} else {
retval = serial_link_irq_chain(up);
if (retval)
spin_unlock_irqrestore(&up->port.lock, flags);
/*
+ * Clear the interrupt registers again for luck, and clear the
+ * saved flags to avoid getting false values from polling
+ * routines or the previous session.
+ */
+ serial_inp(up, UART_LSR);
+ serial_inp(up, UART_RX);
+ serial_inp(up, UART_IIR);
+ serial_inp(up, UART_MSR);
+ up->lsr_saved_flags = 0;
+ up->msr_saved_flags = 0;
+
+ /*
* Finally, enable interrupts. Note: Modem status interrupts
* are set via set_termios(), which will be occurring imminently
* anyway, so we don't enable them here.
(void) inb_p(icp);
}
- /*
- * And clear the interrupt registers again for luck.
- */
- (void) serial_inp(up, UART_LSR);
- (void) serial_inp(up, UART_RX);
- (void) serial_inp(up, UART_IIR);
- (void) serial_inp(up, UART_MSR);
-
return 0;
}
*/
(void) serial_in(up, UART_RX);
- if (!is_real_interrupt(up->port.irq))
- del_timer_sync(&up->timer);
- else
+ del_timer_sync(&up->timer);
+ up->timer.function = serial8250_timeout;
+ if (is_real_interrupt(up->port.irq))
serial_unlink_irq_chain(up);
}
}
static void
-serial8250_set_termios(struct uart_port *port, struct termios *termios,
- struct termios *old)
+serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned char cval, fcr = 0;
/*
* Ask the core to calculate the divisor for us.
*/
- baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = serial8250_get_divisor(port, baud);
/*
* Oxford Semi 952 rev B workaround
*/
if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0)
- quot ++;
+ quot++;
if (up->capabilities & UART_CAP_FIFO && up->port.fifosize > 1) {
if (baud < 2400)
serial_outp(up, UART_EFR, efr);
}
+#ifdef CONFIG_ARCH_OMAP15XX
+ /* Workaround to enable 115200 baud on OMAP1510 internal ports */
+ if (cpu_is_omap1510() && is_omap_port((unsigned int)up->port.membase)) {
+ if (baud == 115200) {
+ quot = 1;
+ serial_out(up, UART_OMAP_OSC_12M_SEL, 1);
+ } else
+ serial_out(up, UART_OMAP_OSC_12M_SEL, 0);
+ }
+#endif
+
if (up->capabilities & UART_NATSEMI) {
/* Switch to bank 2 not bank 1, to avoid resetting EXCR2 */
serial_outp(up, UART_LCR, 0xe0);
}
serial8250_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
+ tty_termios_encode_baud_rate(termios, baud, baud);
}
static void
case UPIO_AU:
size = 0x100000;
/* fall thru */
+ case UPIO_TSI:
+ case UPIO_MEM32:
case UPIO_MEM:
+ case UPIO_DWAPB:
if (!up->port.mapbase)
break;
case UPIO_AU:
size = 0x100000;
/* fall thru */
+ case UPIO_TSI:
+ case UPIO_MEM32:
case UPIO_MEM:
+ case UPIO_DWAPB:
if (!up->port.mapbase)
break;
{
unsigned long start = UART_RSA_BASE << up->port.regshift;
unsigned int size = 8 << up->port.regshift;
- int ret = 0;
+ int ret = -EINVAL;
switch (up->port.iotype) {
- case UPIO_MEM:
- ret = -EINVAL;
- break;
-
case UPIO_HUB6:
case UPIO_PORT:
start += up->port.iobase;
- if (!request_region(start, size, "serial-rsa"))
+ if (request_region(start, size, "serial-rsa"))
+ ret = 0;
+ else
ret = -EBUSY;
break;
}
unsigned int size = 8 << up->port.regshift;
switch (up->port.iotype) {
- case UPIO_MEM:
- break;
-
case UPIO_HUB6:
case UPIO_PORT:
release_region(up->port.iobase + offset, size);
#ifdef CONFIG_SERIAL_8250_CONSOLE
-#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
-
-/*
- * Wait for transmitter & holding register to empty
- */
-static inline void wait_for_xmitr(struct uart_8250_port *up, int bits)
-{
- unsigned int status, tmout = 10000;
-
- /* Wait up to 10ms for the character(s) to be sent. */
- do {
- status = serial_in(up, UART_LSR);
-
- if (status & UART_LSR_BI)
- up->lsr_break_flag = UART_LSR_BI;
-
- if (--tmout == 0)
- break;
- udelay(1);
- } while ((status & bits) != bits);
-
- /* Wait up to 1s for flow control if necessary */
- if (up->port.flags & UPF_CONS_FLOW) {
- tmout = 1000000;
- while (--tmout &&
- ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
- udelay(1);
- }
-}
-
static void serial8250_console_putchar(struct uart_port *port, int ch)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
wait_for_xmitr(up, BOTH_EMPTY);
serial_out(up, UART_IER, ier);
+ /*
+ * The receive handling will happen properly because the
+ * receive ready bit will still be set; it is not cleared
+ * on read. However, modem control will not, we must
+ * call it if we have saved something in the saved flags
+ * while processing with interrupts off.
+ */
+ if (up->msr_saved_flags)
+ check_modem_status(up);
+
if (locked)
spin_unlock(&up->port.lock);
local_irq_restore(flags);
}
-static int serial8250_console_setup(struct console *co, char *options)
+static int __init serial8250_console_setup(struct console *co, char *options)
{
struct uart_port *port;
int baud = 9600;
return uart_set_options(port, co, baud, parity, bits, flow);
}
+static int serial8250_console_early_setup(void)
+{
+ return serial8250_find_port_for_earlycon();
+}
+
static struct uart_driver serial8250_reg;
static struct console serial8250_console = {
.name = "ttyS",
.write = serial8250_console_write,
.device = uart_console_device,
.setup = serial8250_console_setup,
+ .early_setup = serial8250_console_early_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &serial8250_reg,
}
console_initcall(serial8250_console_init);
-static int __init find_port(struct uart_port *p)
+int serial8250_find_port(struct uart_port *p)
{
int line;
struct uart_port *port;
return -ENODEV;
}
-int __init serial8250_start_console(struct uart_port *port, char *options)
-{
- int line;
-
- line = find_port(port);
- if (line < 0)
- return -ENODEV;
-
- add_preferred_console("ttyS", line, options);
- printk("Adding console on ttyS%d at %s 0x%lx (options '%s')\n",
- line, port->iotype == UPIO_MEM ? "MMIO" : "I/O port",
- port->iotype == UPIO_MEM ? (unsigned long) port->mapbase :
- (unsigned long) port->iobase, options);
- if (!(serial8250_console.flags & CON_ENABLED)) {
- serial8250_console.flags &= ~CON_PRINTBUFFER;
- register_console(&serial8250_console);
- }
- return line;
-}
-
#define SERIAL8250_CONSOLE &serial8250_console
#else
#define SERIAL8250_CONSOLE NULL
/**
* serial8250_suspend_port - suspend one serial port
* @line: serial line number
- * @level: the level of port suspension, as per uart_suspend_port
*
* Suspend one serial port.
*/
/**
* serial8250_resume_port - resume one serial port
* @line: serial line number
- * @level: the level of port resumption, as per uart_resume_port
*
* Resume one serial port.
*/
void serial8250_resume_port(int line)
{
- uart_resume_port(&serial8250_reg, &serial8250_ports[line].port);
+ struct uart_8250_port *up = &serial8250_ports[line];
+
+ if (up->capabilities & UART_NATSEMI) {
+ unsigned char tmp;
+
+ /* Ensure it's still in high speed mode */
+ serial_outp(up, UART_LCR, 0xE0);
+
+ tmp = serial_in(up, 0x04); /* EXCR2 */
+ tmp &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
+ tmp |= 0x10; /* 1.625 divisor for baud_base --> 921600 */
+ serial_outp(up, 0x04, tmp);
+
+ serial_outp(up, UART_LCR, 0);
+ }
+ uart_resume_port(&serial8250_reg, &up->port);
}
/*
memset(&port, 0, sizeof(struct uart_port));
for (i = 0; p && p->flags != 0; p++, i++) {
- port.iobase = p->iobase;
- port.membase = p->membase;
- port.irq = p->irq;
- port.uartclk = p->uartclk;
- port.regshift = p->regshift;
- port.iotype = p->iotype;
- port.flags = p->flags;
- port.mapbase = p->mapbase;
- port.hub6 = p->hub6;
- port.dev = &dev->dev;
+ port.iobase = p->iobase;
+ port.membase = p->membase;
+ port.irq = p->irq;
+ port.uartclk = p->uartclk;
+ port.regshift = p->regshift;
+ port.iotype = p->iotype;
+ port.flags = p->flags;
+ port.mapbase = p->mapbase;
+ port.hub6 = p->hub6;
+ port.private_data = p->private_data;
+ port.dev = &dev->dev;
if (share_irqs)
port.flags |= UPF_SHARE_IRQ;
ret = serial8250_register_port(&port);
if (ret < 0) {
dev_err(&dev->dev, "unable to register port at index %d "
- "(IO%lx MEM%lx IRQ%d): %d\n", i,
- p->iobase, p->mapbase, p->irq, ret);
+ "(IO%lx MEM%llx IRQ%d): %d\n", i,
+ p->iobase, (unsigned long long)p->mapbase,
+ p->irq, ret);
}
}
return 0;
struct uart_8250_port *up = &serial8250_ports[i];
if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
- uart_resume_port(&serial8250_reg, &up->port);
+ serial8250_resume_port(i);
}
return 0;
if (uart) {
uart_remove_one_port(&serial8250_reg, &uart->port);
- uart->port.iobase = port->iobase;
- uart->port.membase = port->membase;
- uart->port.irq = port->irq;
- uart->port.uartclk = port->uartclk;
- uart->port.fifosize = port->fifosize;
- uart->port.regshift = port->regshift;
- uart->port.iotype = port->iotype;
- uart->port.flags = port->flags | UPF_BOOT_AUTOCONF;
- uart->port.mapbase = port->mapbase;
+ uart->port.iobase = port->iobase;
+ uart->port.membase = port->membase;
+ uart->port.irq = port->irq;
+ uart->port.uartclk = port->uartclk;
+ uart->port.fifosize = port->fifosize;
+ uart->port.regshift = port->regshift;
+ uart->port.iotype = port->iotype;
+ uart->port.flags = port->flags | UPF_BOOT_AUTOCONF;
+ uart->port.mapbase = port->mapbase;
+ uart->port.private_data = port->private_data;
if (port->dev)
uart->port.dev = port->dev;