- Integrate ql12160_set_target_parameters() with 1280 version
- Make qla1280_setup() non static
- Do not call qla1280_check_for_dead_scsi_bus() on every I/O request
- sent to the card - this command pauses the firmare!!!
+ sent to the card - this command pauses the firmware!!!
Rev 3.23.15 Beta March 19, 2002, Jes Sorensen
- Clean up qla1280.h - remove obsolete QL_DEBUG_LEVEL_x definitions
- Remove a pile of pointless and confusing (srb_t **) and
#include <linux/interrupt.h>
#include <linux/init.h>
#include <linux/dma-mapping.h>
+#include <linux/firmware.h>
#include <asm/io.h>
#include <asm/irq.h>
#define MEMORY_MAPPED_IO 1
#endif
-#define UNIQUE_FW_NAME
#include "qla1280.h"
-#include "ql12160_fw.h" /* ISP RISC codes */
-#include "ql1280_fw.h"
-#include "ql1040_fw.h"
#ifndef BITS_PER_LONG
#error "BITS_PER_LONG not defined!"
struct qla_boards {
unsigned char name[9]; /* Board ID String */
int numPorts; /* Number of SCSI ports */
- unsigned short *fwcode; /* pointer to FW array */
- unsigned short *fwlen; /* number of words in array */
- unsigned short *fwstart; /* start address for F/W */
- unsigned char *fwver; /* Ptr to F/W version array */
+ char *fwname; /* firmware name */
};
/* NOTE: the last argument in each entry is used to index ql1280_board_tbl */
static struct qla_boards ql1280_board_tbl[] = {
/* Name , Number of ports, FW details */
- {"QLA12160", 2, &fw12160i_code01[0], &fw12160i_length01,
- &fw12160i_addr01, &fw12160i_version_str[0]},
- {"QLA1040", 1, &risc_code01[0], &risc_code_length01,
- &risc_code_addr01, &firmware_version[0]},
- {"QLA1080", 1, &fw1280ei_code01[0], &fw1280ei_length01,
- &fw1280ei_addr01, &fw1280ei_version_str[0]},
- {"QLA1240", 2, &fw1280ei_code01[0], &fw1280ei_length01,
- &fw1280ei_addr01, &fw1280ei_version_str[0]},
- {"QLA1280", 2, &fw1280ei_code01[0], &fw1280ei_length01,
- &fw1280ei_addr01, &fw1280ei_version_str[0]},
- {"QLA10160", 1, &fw12160i_code01[0], &fw12160i_length01,
- &fw12160i_addr01, &fw12160i_version_str[0]},
- {" ", 0}
+ {"QLA12160", 2, "qlogic/12160.bin"},
+ {"QLA1040", 1, "qlogic/1040.bin"},
+ {"QLA1080", 1, "qlogic/1280.bin"},
+ {"QLA1240", 2, "qlogic/1280.bin"},
+ {"QLA1280", 2, "qlogic/1280.bin"},
+ {"QLA10160", 1, "qlogic/12160.bin"},
+ {" ", 0, " "},
};
static int qla1280_verbose = 1;
/* The firmware interface is, um, interesting, in that the
* actual firmware image on the chip is little endian, thus,
* the process of taking that image to the CPU would end up
- * little endian. However, the firmare interface requires it
+ * little endian. However, the firmware interface requires it
* to be read a word (two bytes) at a time.
*
* The net result of this would be that the word (and
sprintf (bp,
"QLogic %s PCI to SCSI Host Adapter\n"
" Firmware version: %2d.%02d.%02d, Driver version %s",
- &bdp->name[0], bdp->fwver[0], bdp->fwver[1], bdp->fwver[2],
+ &bdp->name[0], ha->fwver1, ha->fwver2, ha->fwver3,
QLA1280_VERSION);
return bp;
}
static int
qla1280_load_firmware_pio(struct scsi_qla_host *ha)
{
- uint16_t risc_address, *risc_code_address, risc_code_size;
+ const struct firmware *fw;
+ const __le16 *fw_data;
+ uint16_t risc_address, risc_code_size;
uint16_t mb[MAILBOX_REGISTER_COUNT], i;
int err;
+ err = request_firmware(&fw, ql1280_board_tbl[ha->devnum].fwname,
+ &ha->pdev->dev);
+ if (err) {
+ printk(KERN_ERR "Failed to load image \"%s\" err %d\n",
+ ql1280_board_tbl[ha->devnum].fwname, err);
+ return err;
+ }
+ if ((fw->size % 2) || (fw->size < 6)) {
+ printk(KERN_ERR "Bogus length %zu in image \"%s\"\n",
+ fw->size, ql1280_board_tbl[ha->devnum].fwname);
+ err = -EINVAL;
+ goto out;
+ }
+ ha->fwver1 = fw->data[0];
+ ha->fwver2 = fw->data[1];
+ ha->fwver3 = fw->data[2];
+ fw_data = (const __le16 *)&fw->data[0];
+ ha->fwstart = __le16_to_cpu(fw_data[2]);
+
/* Load RISC code. */
- risc_address = *ql1280_board_tbl[ha->devnum].fwstart;
- risc_code_address = ql1280_board_tbl[ha->devnum].fwcode;
- risc_code_size = *ql1280_board_tbl[ha->devnum].fwlen;
+ risc_address = ha->fwstart;
+ fw_data = (const __le16 *)&fw->data[6];
+ risc_code_size = (fw->size - 6) / 2;
for (i = 0; i < risc_code_size; i++) {
mb[0] = MBC_WRITE_RAM_WORD;
mb[1] = risc_address + i;
- mb[2] = risc_code_address[i];
+ mb[2] = __le16_to_cpu(fw_data[i]);
err = qla1280_mailbox_command(ha, BIT_0 | BIT_1 | BIT_2, mb);
if (err) {
printk(KERN_ERR "scsi(%li): Failed to load firmware\n",
ha->host_no);
- return err;
+ goto out;
}
}
-
- return 0;
+out:
+ release_firmware(fw);
+ return err;
}
#define DUMP_IT_BACK 0 /* for debug of RISC loading */
static int
qla1280_load_firmware_dma(struct scsi_qla_host *ha)
{
- uint16_t risc_address, *risc_code_address, risc_code_size;
+ const struct firmware *fw;
+ const __le16 *fw_data;
+ uint16_t risc_address, risc_code_size;
uint16_t mb[MAILBOX_REGISTER_COUNT], cnt;
int err = 0, num, i;
#if DUMP_IT_BACK
return -ENOMEM;
#endif
+ err = request_firmware(&fw, ql1280_board_tbl[ha->devnum].fwname,
+ &ha->pdev->dev);
+ if (err) {
+ printk(KERN_ERR "Failed to load image \"%s\" err %d\n",
+ ql1280_board_tbl[ha->devnum].fwname, err);
+ return err;
+ }
+ if ((fw->size % 2) || (fw->size < 6)) {
+ printk(KERN_ERR "Bogus length %zu in image \"%s\"\n",
+ fw->size, ql1280_board_tbl[ha->devnum].fwname);
+ err = -EINVAL;
+ goto out;
+ }
+ ha->fwver1 = fw->data[0];
+ ha->fwver2 = fw->data[1];
+ ha->fwver3 = fw->data[2];
+ fw_data = (const __le16 *)&fw->data[0];
+ ha->fwstart = __le16_to_cpu(fw_data[2]);
+
/* Load RISC code. */
- risc_address = *ql1280_board_tbl[ha->devnum].fwstart;
- risc_code_address = ql1280_board_tbl[ha->devnum].fwcode;
- risc_code_size = *ql1280_board_tbl[ha->devnum].fwlen;
+ risc_address = ha->fwstart;
+ fw_data = (const __le16 *)&fw->data[6];
+ risc_code_size = (fw->size - 6) / 2;
dprintk(1, "%s: DMA RISC code (%i) words\n",
- __FUNCTION__, risc_code_size);
+ __func__, risc_code_size);
num = 0;
while (risc_code_size > 0) {
dprintk(2, "qla1280_setup_chip: loading risc @ =(0x%p),"
"%d,%d(0x%x)\n",
- risc_code_address, cnt, num, risc_address);
+ fw_data, cnt, num, risc_address);
for(i = 0; i < cnt; i++)
- ((__le16 *)ha->request_ring)[i] =
- cpu_to_le16(risc_code_address[i]);
+ ((__le16 *)ha->request_ring)[i] = fw_data[i];
mb[0] = MBC_LOAD_RAM;
mb[1] = risc_address;
mb[7] = pci_dma_hi32(ha->request_dma) & 0xffff;
mb[6] = pci_dma_hi32(ha->request_dma) >> 16;
dprintk(2, "%s: op=%d 0x%p = 0x%4x,0x%4x,0x%4x,0x%4x\n",
- __FUNCTION__, mb[0],
+ __func__, mb[0],
(void *)(long)ha->request_dma,
mb[6], mb[7], mb[2], mb[3]);
err = qla1280_mailbox_command(ha, BIT_4 | BIT_3 | BIT_2 |
if (tbuf[i] != sp[i] && warn++ < 10) {
printk(KERN_ERR "%s: FW compare error @ "
"byte(0x%x) loop#=%x\n",
- __FUNCTION__, i, num);
+ __func__, i, num);
printk(KERN_ERR "%s: FWbyte=%x "
"FWfromChip=%x\n",
- __FUNCTION__, sp[i], tbuf[i]);
+ __func__, sp[i], tbuf[i]);
/*break; */
}
}
#endif
risc_address += cnt;
risc_code_size = risc_code_size - cnt;
- risc_code_address = risc_code_address + cnt;
+ fw_data = fw_data + cnt;
num++;
}
#if DUMP_IT_BACK
pci_free_consistent(ha->pdev, 8000, tbuf, p_tbuf);
#endif
+ release_firmware(fw);
return err;
}
int err;
dprintk(1, "%s: Verifying checksum of loaded RISC code.\n",
- __FUNCTION__);
+ __func__);
/* Verify checksum of loaded RISC code. */
mb[0] = MBC_VERIFY_CHECKSUM;
/* mb[1] = ql12_risc_code_addr01; */
- mb[1] = *ql1280_board_tbl[ha->devnum].fwstart;
+ mb[1] = ha->fwstart;
err = qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);
if (err) {
printk(KERN_ERR "scsi(%li): RISC checksum failed.\n", ha->host_no);
}
/* Start firmware execution. */
- dprintk(1, "%s: start firmware running.\n", __FUNCTION__);
+ dprintk(1, "%s: start firmware running.\n", __func__);
mb[0] = MBC_EXECUTE_FIRMWARE;
- mb[1] = *ql1280_board_tbl[ha->devnum].fwstart;
+ mb[1] = ha->fwstart;
err = qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);
if (err) {
printk(KERN_ERR "scsi(%li): Failed to start firmware\n",
nv->bus[bus].config_2.req_ack_active_negation = 1;
nv->bus[bus].config_2.data_line_active_negation = 1;
nv->bus[bus].selection_timeout = 250;
- nv->bus[bus].max_queue_depth = 256;
+ nv->bus[bus].max_queue_depth = 32;
if (IS_ISP1040(ha)) {
nv->bus[bus].bus_reset_delay = 3;
status = qla1280_mailbox_command(ha, 0x0f, mb);
/* Save Tag queuing enable flag. */
- flag = (BIT_0 << target) & mb[0];
+ flag = (BIT_0 << target);
if (nv->bus[bus].target[target].parameter.tag_queuing)
ha->bus_settings[bus].qtag_enables |= flag;
/* Check for room in outstanding command list. */
for (cnt = 0; cnt < MAX_OUTSTANDING_COMMANDS &&
- ha->outstanding_cmds[cnt] != 0; cnt++);
+ ha->outstanding_cmds[cnt] != NULL; cnt++);
if (cnt >= MAX_OUTSTANDING_COMMANDS) {
status = 1;
memset(((char *)pkt + 8), 0, (REQUEST_ENTRY_SIZE - 8));
/* Set ISP command timeout. */
- pkt->timeout = cpu_to_le16(cmd->timeout_per_command/HZ);
+ pkt->timeout = cpu_to_le16(cmd->request->timeout/HZ);
/* Set device target ID and LUN */
pkt->lun = SCSI_LUN_32(cmd);
memset(((char *)pkt + 8), 0, (REQUEST_ENTRY_SIZE - 8));
/* Set ISP command timeout. */
- pkt->timeout = cpu_to_le16(cmd->timeout_per_command/HZ);
+ pkt->timeout = cpu_to_le16(cmd->request->timeout/HZ);
/* Set device target ID and LUN */
pkt->lun = SCSI_LUN_32(cmd);
ha->devnum = devnum; /* specifies microcode load address */
#ifdef QLA_64BIT_PTR
- if (pci_set_dma_mask(ha->pdev, DMA_64BIT_MASK)) {
- if (pci_set_dma_mask(ha->pdev, DMA_32BIT_MASK)) {
+ if (pci_set_dma_mask(ha->pdev, DMA_BIT_MASK(64))) {
+ if (pci_set_dma_mask(ha->pdev, DMA_BIT_MASK(32))) {
printk(KERN_WARNING "scsi(%li): Unable to set a "
"suitable DMA mask - aborting\n", ha->host_no);
error = -ENODEV;
dprintk(2, "scsi(%li): 64 Bit PCI Addressing Enabled\n",
ha->host_no);
#else
- if (pci_set_dma_mask(ha->pdev, DMA_32BIT_MASK)) {
+ if (pci_set_dma_mask(ha->pdev, DMA_BIT_MASK(32))) {
printk(KERN_WARNING "scsi(%li): Unable to set a "
"suitable DMA mask - aborting\n", ha->host_no);
error = -ENODEV;
error = -ENODEV;
#if MEMORY_MAPPED_IO
- ha->mmpbase = ioremap(pci_resource_start(ha->pdev, 1),
- pci_resource_len(ha->pdev, 1));
+ ha->mmpbase = pci_ioremap_bar(ha->pdev, 1);
if (!ha->mmpbase) {
printk(KERN_INFO "qla1280: Unable to map I/O memory\n");
goto error_free_response_ring;
MODULE_AUTHOR("Qlogic & Jes Sorensen");
MODULE_DESCRIPTION("Qlogic ISP SCSI (qla1x80/qla1x160) driver");
MODULE_LICENSE("GPL");
+MODULE_FIRMWARE("qlogic/1040.bin");
+MODULE_FIRMWARE("qlogic/1280.bin");
+MODULE_FIRMWARE("qlogic/12160.bin");
MODULE_VERSION(QLA1280_VERSION);
/*
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff