#include <linux/sched.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
-#include "scsi.h"
#include <scsi/scsi_host.h>
+#include <scsi/scsi_cmnd.h>
#include <linux/libata.h>
#include <asm/io.h>
#define DRV_NAME "ahci"
-#define DRV_VERSION "1.01"
+#define DRV_VERSION "1.2"
enum {
AHCI_IRQ_ON_SG = (1 << 31),
AHCI_CMD_ATAPI = (1 << 5),
AHCI_CMD_WRITE = (1 << 6),
+ AHCI_CMD_PREFETCH = (1 << 7),
+ AHCI_CMD_RESET = (1 << 8),
+ AHCI_CMD_CLR_BUSY = (1 << 10),
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
/* HOST_CAP bits */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
+ HOST_CAP_CLO = (1 << 24), /* Command List Override support */
/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
PORT_IRQ_D2H_REG_FIS,
/* PORT_CMD bits */
+ PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */
PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */
+ PORT_CMD_CLO = (1 << 3), /* Command list override */
PORT_CMD_POWER_ON = (1 << 2), /* Power up device */
PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void ahci_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
-static int ahci_qc_issue(struct ata_queued_cmd *qc);
+static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc);
static irqreturn_t ahci_interrupt (int irq, void *dev_instance, struct pt_regs *regs);
-static void ahci_phy_reset(struct ata_port *ap);
+static int ahci_probe_reset(struct ata_port *ap, unsigned int *classes);
static void ahci_irq_clear(struct ata_port *ap);
static void ahci_eng_timeout(struct ata_port *ap);
static int ahci_port_start(struct ata_port *ap);
static inline int ahci_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc);
static void ahci_remove_one (struct pci_dev *pdev);
-static Scsi_Host_Template ahci_sht = {
+static struct scsi_host_template ahci_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
- .eh_strategy_handler = ata_scsi_error,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = AHCI_MAX_SG,
- .max_sectors = ATA_MAX_SECTORS,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = AHCI_USE_CLUSTERING,
.dma_boundary = AHCI_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
- .ordered_flush = 1,
};
static const struct ata_port_operations ahci_ops = {
.tf_read = ahci_tf_read,
- .phy_reset = ahci_phy_reset,
+ .probe_reset = ahci_probe_reset,
.qc_prep = ahci_qc_prep,
.qc_issue = ahci_qc_issue,
.port_stop = ahci_port_stop,
};
-static struct ata_port_info ahci_port_info[] = {
+static const struct ata_port_info ahci_port_info[] = {
/* board_ahci */
{
.sht = &ahci_sht,
.host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
- ATA_FLAG_PIO_DMA,
+ ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = 0x7f, /* udma0-6 ; FIXME */
.port_ops = &ahci_ops,
},
};
-static struct pci_device_id ahci_pci_tbl[] = {
+static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VENDOR_ID_INTEL, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ICH6 */
{ PCI_VENDOR_ID_INTEL, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ESB2 */
{ PCI_VENDOR_ID_INTEL, 0x27c6, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ICH7-M DH */
+ { PCI_VENDOR_ID_INTEL, 0x2821, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* ICH8 */
+ { PCI_VENDOR_ID_INTEL, 0x2822, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* ICH8 */
+ { PCI_VENDOR_ID_INTEL, 0x2824, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* ICH8 */
+ { PCI_VENDOR_ID_INTEL, 0x2829, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* ICH8M */
+ { PCI_VENDOR_ID_INTEL, 0x282a, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* ICH8M */
+ { 0x197b, 0x2360, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* JMicron JMB360 */
+ { 0x197b, 0x2363, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* JMicron JMB363 */
+ { PCI_VENDOR_ID_ATI, 0x4380, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* ATI SB600 non-raid */
+ { PCI_VENDOR_ID_ATI, 0x4381, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* ATI SB600 raid */
{ } /* terminate list */
};
void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
void *mem;
dma_addr_t mem_dma;
+ int rc;
pp = kmalloc(sizeof(*pp), GFP_KERNEL);
if (!pp)
return -ENOMEM;
memset(pp, 0, sizeof(*pp));
+ rc = ata_pad_alloc(ap, dev);
+ if (rc) {
+ kfree(pp);
+ return rc;
+ }
+
mem = dma_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma, GFP_KERNEL);
if (!mem) {
+ ata_pad_free(ap, dev);
kfree(pp);
return -ENOMEM;
}
ap->private_data = NULL;
dma_free_coherent(dev, AHCI_PORT_PRIV_DMA_SZ,
pp->cmd_slot, pp->cmd_slot_dma);
+ ata_pad_free(ap, dev);
kfree(pp);
}
writel(val, (void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
}
-static void ahci_phy_reset(struct ata_port *ap)
+static int ahci_stop_engine(struct ata_port *ap)
{
- void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr;
- struct ata_taskfile tf;
- struct ata_device *dev = &ap->device[0];
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+ int work;
u32 tmp;
- __sata_phy_reset(ap);
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp &= ~PORT_CMD_START;
+ writel(tmp, port_mmio + PORT_CMD);
- if (ap->flags & ATA_FLAG_PORT_DISABLED)
- return;
+ /* wait for engine to stop. TODO: this could be
+ * as long as 500 msec
+ */
+ work = 1000;
+ while (work-- > 0) {
+ tmp = readl(port_mmio + PORT_CMD);
+ if ((tmp & PORT_CMD_LIST_ON) == 0)
+ return 0;
+ udelay(10);
+ }
+
+ return -EIO;
+}
+
+static void ahci_start_engine(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+ u32 tmp;
+
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp |= PORT_CMD_START;
+ writel(tmp, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+}
+
+static unsigned int ahci_dev_classify(struct ata_port *ap)
+{
+ void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr;
+ struct ata_taskfile tf;
+ u32 tmp;
tmp = readl(port_mmio + PORT_SIG);
tf.lbah = (tmp >> 24) & 0xff;
tf.lbal = (tmp >> 8) & 0xff;
tf.nsect = (tmp) & 0xff;
- dev->class = ata_dev_classify(&tf);
- if (!ata_dev_present(dev))
- ata_port_disable(ap);
+ return ata_dev_classify(&tf);
+}
+
+static void ahci_fill_cmd_slot(struct ahci_port_priv *pp, u32 opts)
+{
+ pp->cmd_slot[0].opts = cpu_to_le32(opts);
+ pp->cmd_slot[0].status = 0;
+ pp->cmd_slot[0].tbl_addr = cpu_to_le32(pp->cmd_tbl_dma & 0xffffffff);
+ pp->cmd_slot[0].tbl_addr_hi = cpu_to_le32((pp->cmd_tbl_dma >> 16) >> 16);
+}
+
+static int ahci_poll_register(void __iomem *reg, u32 mask, u32 val,
+ unsigned long interval_msec,
+ unsigned long timeout_msec)
+{
+ unsigned long timeout;
+ u32 tmp;
+
+ timeout = jiffies + (timeout_msec * HZ) / 1000;
+ do {
+ tmp = readl(reg);
+ if ((tmp & mask) == val)
+ return 0;
+ msleep(interval_msec);
+ } while (time_before(jiffies, timeout));
+
+ return -1;
+}
+
+static int ahci_softreset(struct ata_port *ap, int verbose, unsigned int *class)
+{
+ struct ahci_host_priv *hpriv = ap->host_set->private_data;
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+ const u32 cmd_fis_len = 5; /* five dwords */
+ const char *reason = NULL;
+ struct ata_taskfile tf;
+ u8 *fis;
+ int rc;
+
+ DPRINTK("ENTER\n");
+
+ /* prepare for SRST (AHCI-1.1 10.4.1) */
+ rc = ahci_stop_engine(ap);
+ if (rc) {
+ reason = "failed to stop engine";
+ goto fail_restart;
+ }
+
+ /* check BUSY/DRQ, perform Command List Override if necessary */
+ ahci_tf_read(ap, &tf);
+ if (tf.command & (ATA_BUSY | ATA_DRQ)) {
+ u32 tmp;
+
+ if (!(hpriv->cap & HOST_CAP_CLO)) {
+ rc = -EIO;
+ reason = "port busy but no CLO";
+ goto fail_restart;
+ }
+
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp |= PORT_CMD_CLO;
+ writel(tmp, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+
+ if (ahci_poll_register(port_mmio + PORT_CMD, PORT_CMD_CLO, 0x0,
+ 1, 500)) {
+ rc = -EIO;
+ reason = "CLO failed";
+ goto fail_restart;
+ }
+ }
+
+ /* restart engine */
+ ahci_start_engine(ap);
+
+ ata_tf_init(ap, &tf, 0);
+ fis = pp->cmd_tbl;
+
+ /* issue the first D2H Register FIS */
+ ahci_fill_cmd_slot(pp, cmd_fis_len | AHCI_CMD_RESET | AHCI_CMD_CLR_BUSY);
+
+ tf.ctl |= ATA_SRST;
+ ata_tf_to_fis(&tf, fis, 0);
+ fis[1] &= ~(1 << 7); /* turn off Command FIS bit */
+
+ writel(1, port_mmio + PORT_CMD_ISSUE);
+ readl(port_mmio + PORT_CMD_ISSUE); /* flush */
+
+ if (ahci_poll_register(port_mmio + PORT_CMD_ISSUE, 0x1, 0x0, 1, 500)) {
+ rc = -EIO;
+ reason = "1st FIS failed";
+ goto fail;
+ }
+
+ /* spec says at least 5us, but be generous and sleep for 1ms */
+ msleep(1);
+
+ /* issue the second D2H Register FIS */
+ ahci_fill_cmd_slot(pp, cmd_fis_len);
+
+ tf.ctl &= ~ATA_SRST;
+ ata_tf_to_fis(&tf, fis, 0);
+ fis[1] &= ~(1 << 7); /* turn off Command FIS bit */
+
+ writel(1, port_mmio + PORT_CMD_ISSUE);
+ readl(port_mmio + PORT_CMD_ISSUE); /* flush */
+
+ /* spec mandates ">= 2ms" before checking status.
+ * We wait 150ms, because that was the magic delay used for
+ * ATAPI devices in Hale Landis's ATADRVR, for the period of time
+ * between when the ATA command register is written, and then
+ * status is checked. Because waiting for "a while" before
+ * checking status is fine, post SRST, we perform this magic
+ * delay here as well.
+ */
+ msleep(150);
+
+ *class = ATA_DEV_NONE;
+ if (sata_dev_present(ap)) {
+ if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
+ rc = -EIO;
+ reason = "device not ready";
+ goto fail;
+ }
+ *class = ahci_dev_classify(ap);
+ }
+
+ DPRINTK("EXIT, class=%u\n", *class);
+ return 0;
+
+ fail_restart:
+ ahci_start_engine(ap);
+ fail:
+ if (verbose)
+ printk(KERN_ERR "ata%u: softreset failed (%s)\n",
+ ap->id, reason);
+ else
+ DPRINTK("EXIT, rc=%d reason=\"%s\"\n", rc, reason);
+ return rc;
+}
+
+static int ahci_hardreset(struct ata_port *ap, int verbose, unsigned int *class)
+{
+ int rc;
+
+ DPRINTK("ENTER\n");
+
+ ahci_stop_engine(ap);
+ rc = sata_std_hardreset(ap, verbose, class);
+ ahci_start_engine(ap);
+
+ if (rc == 0)
+ *class = ahci_dev_classify(ap);
+ if (*class == ATA_DEV_UNKNOWN)
+ *class = ATA_DEV_NONE;
+
+ DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
+ return rc;
+}
+
+static void ahci_postreset(struct ata_port *ap, unsigned int *class)
+{
+ void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr;
+ u32 new_tmp, tmp;
+
+ ata_std_postreset(ap, class);
+
+ /* Make sure port's ATAPI bit is set appropriately */
+ new_tmp = tmp = readl(port_mmio + PORT_CMD);
+ if (*class == ATA_DEV_ATAPI)
+ new_tmp |= PORT_CMD_ATAPI;
+ else
+ new_tmp &= ~PORT_CMD_ATAPI;
+ if (new_tmp != tmp) {
+ writel(new_tmp, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+ }
+}
+
+static int ahci_probe_reset(struct ata_port *ap, unsigned int *classes)
+{
+ return ata_drive_probe_reset(ap, ata_std_probeinit,
+ ahci_softreset, ahci_hardreset,
+ ahci_postreset, classes);
}
static u8 ahci_check_status(struct ata_port *ap)
ata_tf_from_fis(d2h_fis, tf);
}
-static void ahci_fill_sg(struct ata_queued_cmd *qc)
+static unsigned int ahci_fill_sg(struct ata_queued_cmd *qc)
{
struct ahci_port_priv *pp = qc->ap->private_data;
- unsigned int i;
+ struct scatterlist *sg;
+ struct ahci_sg *ahci_sg;
+ unsigned int n_sg = 0;
VPRINTK("ENTER\n");
/*
* Next, the S/G list.
*/
- for (i = 0; i < qc->n_elem; i++) {
- u32 sg_len;
- dma_addr_t addr;
+ ahci_sg = pp->cmd_tbl_sg;
+ ata_for_each_sg(sg, qc) {
+ dma_addr_t addr = sg_dma_address(sg);
+ u32 sg_len = sg_dma_len(sg);
- addr = sg_dma_address(&qc->sg[i]);
- sg_len = sg_dma_len(&qc->sg[i]);
+ ahci_sg->addr = cpu_to_le32(addr & 0xffffffff);
+ ahci_sg->addr_hi = cpu_to_le32((addr >> 16) >> 16);
+ ahci_sg->flags_size = cpu_to_le32(sg_len - 1);
- pp->cmd_tbl_sg[i].addr = cpu_to_le32(addr & 0xffffffff);
- pp->cmd_tbl_sg[i].addr_hi = cpu_to_le32((addr >> 16) >> 16);
- pp->cmd_tbl_sg[i].flags_size = cpu_to_le32(sg_len - 1);
+ ahci_sg++;
+ n_sg++;
}
+
+ return n_sg;
}
static void ahci_qc_prep(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ahci_port_priv *pp = ap->private_data;
+ int is_atapi = is_atapi_taskfile(&qc->tf);
u32 opts;
const u32 cmd_fis_len = 5; /* five dwords */
-
- /*
- * Fill in command slot information (currently only one slot,
- * slot 0, is currently since we don't do queueing)
- */
-
- opts = (qc->n_elem << 16) | cmd_fis_len;
- if (qc->tf.flags & ATA_TFLAG_WRITE)
- opts |= AHCI_CMD_WRITE;
- if (is_atapi_taskfile(&qc->tf))
- opts |= AHCI_CMD_ATAPI;
-
- pp->cmd_slot[0].opts = cpu_to_le32(opts);
- pp->cmd_slot[0].status = 0;
- pp->cmd_slot[0].tbl_addr = cpu_to_le32(pp->cmd_tbl_dma & 0xffffffff);
- pp->cmd_slot[0].tbl_addr_hi = cpu_to_le32((pp->cmd_tbl_dma >> 16) >> 16);
+ unsigned int n_elem;
/*
* Fill in command table information. First, the header,
* a SATA Register - Host to Device command FIS.
*/
ata_tf_to_fis(&qc->tf, pp->cmd_tbl, 0);
- if (opts & AHCI_CMD_ATAPI) {
+ if (is_atapi) {
memset(pp->cmd_tbl + AHCI_CMD_TBL_CDB, 0, 32);
- memcpy(pp->cmd_tbl + AHCI_CMD_TBL_CDB, qc->cdb, ap->cdb_len);
+ memcpy(pp->cmd_tbl + AHCI_CMD_TBL_CDB, qc->cdb,
+ qc->dev->cdb_len);
}
- if (!(qc->flags & ATA_QCFLAG_DMAMAP))
- return;
+ n_elem = 0;
+ if (qc->flags & ATA_QCFLAG_DMAMAP)
+ n_elem = ahci_fill_sg(qc);
- ahci_fill_sg(qc);
+ /*
+ * Fill in command slot information.
+ */
+ opts = cmd_fis_len | n_elem << 16;
+ if (qc->tf.flags & ATA_TFLAG_WRITE)
+ opts |= AHCI_CMD_WRITE;
+ if (is_atapi)
+ opts |= AHCI_CMD_ATAPI | AHCI_CMD_PREFETCH;
+
+ ahci_fill_cmd_slot(pp, opts);
}
-static void ahci_intr_error(struct ata_port *ap, u32 irq_stat)
+static void ahci_restart_port(struct ata_port *ap, u32 irq_stat)
{
void __iomem *mmio = ap->host_set->mmio_base;
void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
u32 tmp;
- int work;
- /* stop DMA */
- tmp = readl(port_mmio + PORT_CMD);
- tmp &= ~PORT_CMD_START;
- writel(tmp, port_mmio + PORT_CMD);
+ if ((ap->device[0].class != ATA_DEV_ATAPI) ||
+ ((irq_stat & PORT_IRQ_TF_ERR) == 0))
+ printk(KERN_WARNING "ata%u: port reset, "
+ "p_is %x is %x pis %x cmd %x tf %x ss %x se %x\n",
+ ap->id,
+ irq_stat,
+ readl(mmio + HOST_IRQ_STAT),
+ readl(port_mmio + PORT_IRQ_STAT),
+ readl(port_mmio + PORT_CMD),
+ readl(port_mmio + PORT_TFDATA),
+ readl(port_mmio + PORT_SCR_STAT),
+ readl(port_mmio + PORT_SCR_ERR));
- /* wait for engine to stop. TODO: this could be
- * as long as 500 msec
- */
- work = 1000;
- while (work-- > 0) {
- tmp = readl(port_mmio + PORT_CMD);
- if ((tmp & PORT_CMD_LIST_ON) == 0)
- break;
- udelay(10);
- }
+ /* stop DMA */
+ ahci_stop_engine(ap);
/* clear SATA phy error, if any */
tmp = readl(port_mmio + PORT_SCR_ERR);
}
/* re-start DMA */
- tmp = readl(port_mmio + PORT_CMD);
- tmp |= PORT_CMD_START;
- writel(tmp, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
-
- printk(KERN_WARNING "ata%u: error occurred, port reset\n", ap->id);
+ ahci_start_engine(ap);
}
static void ahci_eng_timeout(struct ata_port *ap)
struct ata_queued_cmd *qc;
unsigned long flags;
- DPRINTK("ENTER\n");
+ printk(KERN_WARNING "ata%u: handling error/timeout\n", ap->id);
spin_lock_irqsave(&host_set->lock, flags);
- ahci_intr_error(ap, readl(port_mmio + PORT_IRQ_STAT));
-
+ ahci_restart_port(ap, readl(port_mmio + PORT_IRQ_STAT));
qc = ata_qc_from_tag(ap, ap->active_tag);
- if (!qc) {
- printk(KERN_ERR "ata%u: BUG: timeout without command\n",
- ap->id);
- } else {
- /* hack alert! We cannot use the supplied completion
- * function from inside the ->eh_strategy_handler() thread.
- * libata is the only user of ->eh_strategy_handler() in
- * any kernel, so the default scsi_done() assumes it is
- * not being called from the SCSI EH.
- */
- qc->scsidone = scsi_finish_command;
- ata_qc_complete(qc, AC_ERR_OTHER);
- }
+ qc->err_mask |= AC_ERR_TIMEOUT;
spin_unlock_irqrestore(&host_set->lock, flags);
+
+ ata_eh_qc_complete(qc);
}
static inline int ahci_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
ci = readl(port_mmio + PORT_CMD_ISSUE);
if (likely((ci & 0x1) == 0)) {
if (qc) {
- ata_qc_complete(qc, 0);
+ WARN_ON(qc->err_mask);
+ ata_qc_complete(qc);
qc = NULL;
}
}
if (status & PORT_IRQ_FATAL) {
- ahci_intr_error(ap, status);
- if (qc)
- ata_qc_complete(qc, AC_ERR_OTHER);
+ unsigned int err_mask;
+ if (status & PORT_IRQ_TF_ERR)
+ err_mask = AC_ERR_DEV;
+ else if (status & PORT_IRQ_IF_ERR)
+ err_mask = AC_ERR_ATA_BUS;
+ else
+ err_mask = AC_ERR_HOST_BUS;
+
+ /* command processing has stopped due to error; restart */
+ ahci_restart_port(ap, status);
+
+ if (qc) {
+ qc->err_mask |= err_mask;
+ ata_qc_complete(qc);
+ }
}
return 1;
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->active_tag);
if (!ahci_host_intr(ap, qc))
- if (ata_ratelimit()) {
- struct pci_dev *pdev =
- to_pci_dev(ap->host_set->dev);
- dev_printk(KERN_WARNING, &pdev->dev,
+ if (ata_ratelimit())
+ dev_printk(KERN_WARNING, host_set->dev,
"unhandled interrupt on port %u\n",
i);
- }
VPRINTK("port %u\n", i);
} else {
VPRINTK("port %u (no irq)\n", i);
- if (ata_ratelimit()) {
- struct pci_dev *pdev =
- to_pci_dev(ap->host_set->dev);
- dev_printk(KERN_WARNING, &pdev->dev,
+ if (ata_ratelimit())
+ dev_printk(KERN_WARNING, host_set->dev,
"interrupt on disabled port %u\n", i);
- }
}
irq_ack |= (1 << i);
return IRQ_RETVAL(handled);
}
-static int ahci_qc_issue(struct ata_queued_cmd *qc)
+static unsigned int ahci_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr;
struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
void __iomem *mmio = probe_ent->mmio_base;
u32 tmp, cap_save;
- u16 tmp16;
unsigned int i, j, using_dac;
int rc;
void __iomem *port_mmio;
writel(0xf, mmio + HOST_PORTS_IMPL);
(void) readl(mmio + HOST_PORTS_IMPL); /* flush */
- pci_read_config_word(pdev, 0x92, &tmp16);
- tmp16 |= 0xf;
- pci_write_config_word(pdev, 0x92, tmp16);
+ if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
+ u16 tmp16;
+
+ pci_read_config_word(pdev, 0x92, &tmp16);
+ tmp16 |= 0xf;
+ pci_write_config_word(pdev, 0x92, tmp16);
+ }
hpriv->cap = readl(mmio + HOST_CAP);
hpriv->port_map = readl(mmio + HOST_PORTS_IMPL);
if (have_msi)
hpriv->flags |= AHCI_FLAG_MSI;
+ /* JMicron-specific fixup: make sure we're in AHCI mode */
+ if (pdev->vendor == 0x197b)
+ pci_write_config_byte(pdev, 0x41, 0xa1);
+
/* initialize adapter */
rc = ahci_host_init(probe_ent);
if (rc)
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff