config SCSI
tristate "SCSI device support"
depends on BLOCK
+ select SCSI_DMA if HAS_DMA
---help---
If you want to use a SCSI hard disk, SCSI tape drive, SCSI CD-ROM or
any other SCSI device under Linux, say Y and make sure that you know
However, do not compile this as a module if your root file system
(the one containing the directory /) is located on a SCSI device.
+config SCSI_DMA
+ bool
+ default n
+
config SCSI_TGT
tristate "SCSI target support"
depends on SCSI && EXPERIMENTAL
depends on SCSI
---help---
If you want to use SCSI hard disks, Fibre Channel disks,
+ Serial ATA (SATA) or Parallel ATA (PATA) hard disks,
USB storage or the SCSI or parallel port version of
the IOMEGA ZIP drive, say Y and read the SCSI-HOWTO,
the Disk-HOWTO and the Multi-Disk-HOWTO, available from
don't need this for those tiny 6-slot cdrom changers. Media
changers are listed as "Type: Medium Changer" in /proc/scsi/scsi.
If you have such hardware and want to use it with linux, say Y
- here. Check <file:Documentation/scsi-changer.txt> for details.
+ here. Check <file:Documentation/scsi/scsi-changer.txt> for details.
If you want to compile this as a module ( = code which can be
inserted in and removed from the running kernel whenever you want),
- say M here and read <file:Documentation/modules.txt> and
- <file:Documentation/scsi.txt>. The module will be called ch.o.
+ say M here and read <file:Documentation/kbuild/modules.txt> and
+ <file:Documentation/scsi/scsi.txt>. The module will be called ch.o.
If unsure, say N.
The SCSI subsystem can probe for devices while the rest of the
system continues booting, and even probe devices on different
busses in parallel, leading to a significant speed-up.
+
If you have built SCSI as modules, enabling this option can
be a problem as the devices may not have been found by the
time your system expects them to have been. You can load the
If you build your SCSI drivers into the kernel, then everything
will work fine if you say Y here.
- You can override this choice by specifying scsi_mod.scan="sync"
- or "async" on the kernel's command line.
+ You can override this choice by specifying "scsi_mod.scan=sync"
+ or async on the kernel's command line.
+
+config SCSI_WAIT_SCAN
+ tristate
+ default m
+ depends on SCSI
+ depends on MODULES
menu "SCSI Transports"
depends on SCSI
each attached FiberChannel device to sysfs, say Y.
Otherwise, say N.
+config SCSI_FC_TGT_ATTRS
+ bool "SCSI target support for FiberChannel Transport Attributes"
+ depends on SCSI_FC_ATTRS
+ depends on SCSI_TGT = y || SCSI_TGT = SCSI_FC_ATTRS
+ help
+ If you want to use SCSI target mode drivers enable this option.
+
config SCSI_ISCSI_ATTRS
tristate "iSCSI Transport Attributes"
depends on SCSI && NET
config SCSI_SAS_ATTRS
tristate "SAS Transport Attributes"
- depends on SCSI
+ depends on SCSI && BLK_DEV_BSG
help
If you wish to export transport-specific information about
each attached SAS device to sysfs, say Y.
source "drivers/scsi/libsas/Kconfig"
+config SCSI_SRP_ATTRS
+ tristate "SRP Transport Attributes"
+ depends on SCSI
+ help
+ If you wish to export transport-specific information about
+ each attached SRP device to sysfs, say Y.
+
+config SCSI_SRP_TGT_ATTRS
+ bool "SCSI target support for SRP Transport Attributes"
+ depends on SCSI_SRP_ATTRS
+ depends on SCSI_TGT = y || SCSI_TGT = SCSI_SRP_ATTRS
+ help
+ If you want to use SCSI target mode drivers enable this option.
+
endmenu
-menu "SCSI low-level drivers"
+menuconfig SCSI_LOWLEVEL
+ bool "SCSI low-level drivers"
depends on SCSI!=n
+ default y
+
+if SCSI_LOWLEVEL
config ISCSI_TCP
tristate "iSCSI Initiator over TCP/IP"
config SCSI_7000FASST
tristate "7000FASST SCSI support"
depends on ISA && SCSI && ISA_DMA_API
+ select CHECK_SIGNATURE
help
This driver supports the Western Digital 7000 SCSI host adapter
family. Some information is in the source:
tristate "Adaptec AHA152X/2825 support"
depends on ISA && SCSI && !64BIT
select SCSI_SPI_ATTRS
+ select CHECK_SIGNATURE
---help---
This is a driver for the AHA-1510, AHA-1520, AHA-1522, and AHA-2825
SCSI host adapters. It also works for the AVA-1505, but the IRQ etc.
# All the I2O code and drivers do not seem to be 64bit safe.
config SCSI_DPT_I2O
tristate "Adaptec I2O RAID support "
- depends on !64BIT && SCSI && PCI
+ depends on !64BIT && SCSI && PCI && VIRT_TO_BUS
help
This driver supports all of Adaptec's I2O based RAID controllers as
well as the DPT SmartRaid V cards. This is an Adaptec maintained
config SCSI_ADVANSYS
tristate "AdvanSys SCSI support"
- depends on SCSI
+ depends on SCSI && VIRT_TO_BUS
depends on ISA || EISA || PCI
- depends on BROKEN || X86_32
help
This is a driver for all SCSI host adapters manufactured by
AdvanSys. It is documented in the kernel source in
module will be called in2000.
config SCSI_ARCMSR
- tristate "ARECA ARC11X0[PCI-X]/ARC12X0[PCI-EXPRESS] SATA-RAID support"
+ tristate "ARECA (ARC11xx/12xx/13xx/16xx) SATA/SAS RAID Host Adapter"
depends on PCI && SCSI
help
- This driver supports all of ARECA's SATA RAID controller cards.
+ This driver supports all of ARECA's SATA/SAS RAID controller cards.
This is an ARECA-maintained driver by Erich Chen.
- If you have any problems, please mail to: < erich@areca.com.tw >
+ If you have any problems, please mail to: <erich@areca.com.tw>.
Areca supports Linux RAID config tools.
-
- < http://www.areca.com.tw >
+ Please link <http://www.areca.com.tw>
To compile this driver as a module, choose M here: the
module will be called arcmsr (modprobe arcmsr).
+config SCSI_ARCMSR_AER
+ bool "Enable PCI Error Recovery Capability in Areca Driver(ARCMSR)"
+ depends on SCSI_ARCMSR && PCIEAER
+ default n
+ help
+ The advanced error reporting(AER) capability is "NOT" provided by
+ ARC1200/1201/1202 SATA RAID controllers cards.
+ If your card is one of ARC1200/1201/1202, please use the default setting, n.
+ If your card is other models, you could pick it
+ on condition that the kernel version is greater than 2.6.19.
+ This function is maintained driver by Nick Cheng. If you have any
+ problems or suggestion, you are welcome to contact with <nick.cheng@areca.com.tw>.
+ To enable this function, choose Y here.
+
source "drivers/scsi/megaraid/Kconfig.megaraid"
config SCSI_HPTIOP
config SCSI_BUSLOGIC
tristate "BusLogic SCSI support"
- depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API
+ depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API && VIRT_TO_BUS
---help---
This is support for BusLogic MultiMaster and FlashPoint SCSI Host
Adapters. Consult the SCSI-HOWTO, available from
tristate "DTC3180/3280 SCSI support"
depends on ISA && SCSI
select SCSI_SPI_ATTRS
+ select CHECK_SIGNATURE
help
This is support for DTC 3180/3280 SCSI Host Adapters. Please read
the SCSI-HOWTO, available from
config SCSI_FUTURE_DOMAIN
tristate "Future Domain 16xx SCSI/AHA-2920A support"
depends on (ISA || PCI) && SCSI
+ select CHECK_SIGNATURE
---help---
This is support for Future Domain's 16-bit SCSI host adapters
(TMC-1660/1680, TMC-1650/1670, TMC-3260, TMC-1610M/MER/MEX) and
config SCSI_GDTH
tristate "Intel/ICP (former GDT SCSI Disk Array) RAID Controller support"
- depends on (ISA || EISA || PCI) && SCSI && ISA_DMA_API
+ depends on (ISA || EISA || PCI) && SCSI && ISA_DMA_API && PCI_LEGACY
---help---
Formerly called GDT SCSI Disk Array Controller Support.
config SCSI_IBMMCA
tristate "IBMMCA SCSI support"
- depends on MCA_LEGACY && SCSI
+ depends on MCA && SCSI
---help---
This is support for the IBM SCSI adapter found in many of the PS/2
series computers. These machines have an MCA bus, so you need to
config SCSI_IBMVSCSI
tristate "IBM Virtual SCSI support"
depends on PPC_PSERIES || PPC_ISERIES
+ select SCSI_SRP_ATTRS
help
This is the IBM POWER Virtual SCSI Client
config SCSI_IBMVSCSIS
tristate "IBM Virtual SCSI Server support"
- depends on PPC_PSERIES && SCSI_TGT && SCSI_SRP
+ depends on PPC_PSERIES && SCSI_SRP && SCSI_SRP_TGT_ATTRS
help
This is the SRP target driver for IBM pSeries virtual environments.
many PA-RISC workstations & servers. If you do not know whether you
have a Lasi chip, it is safe to say "Y" here.
+config SCSI_SNI_53C710
+ tristate "SNI RM SCSI support for 53c710"
+ depends on SNI_RM && SCSI
+ select SCSI_SPI_ATTRS
+ select 53C700_LE_ON_BE
+ help
+ This is a driver for the onboard SCSI controller found in older
+ SNI RM workstations & servers.
+
config 53C700_LE_ON_BE
bool
depends on SCSI_LASI700
To compile this driver as a module, choose M here: the
module will be called stex.
+config 53C700_BE_BUS
+ bool
+ depends on SCSI_A4000T || SCSI_ZORRO7XX || MVME16x_SCSI || BVME6000_SCSI
+ default y
+
config SCSI_SYM53C8XX_2
tristate "SYM53C8XX Version 2 SCSI support"
depends on PCI && SCSI
There is no safe option other than using good cabling, right
terminations and SCSI conformant devices.
-config SCSI_NCR53C8XX_PROFILE
- bool "enable profiling"
- depends on SCSI_ZALON || SCSI_NCR_Q720
- help
- This option allows you to enable profiling information gathering.
- These statistics are not very accurate due to the low frequency
- of the kernel clock (100 Hz on i386) and have performance impact
- on systems that use very fast devices.
-
- The normal answer therefore is N.
-
config SCSI_NCR53C8XX_NO_DISCONNECT
bool "not allow targets to disconnect"
depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0
To compile this driver as a module, choose M here: the
module will be called pas16.
-config SCSI_PSI240I
- tristate "PSI240i support"
- depends on ISA && SCSI
- help
- This is support for the PSI240i EIDE interface card which acts as a
- SCSI host adapter. Please read the SCSI-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here: the
- module will be called psi240i.
-
config SCSI_QLOGIC_FAS
tristate "Qlogic FAS SCSI support"
depends on ISA && SCSI
This lpfc driver supports the Emulex LightPulse
Family of Fibre Channel PCI host adapters.
-config SCSI_SEAGATE
- tristate "Seagate ST-02 and Future Domain TMC-8xx SCSI support"
- depends on X86 && ISA && SCSI && BROKEN
- ---help---
- These are 8-bit SCSI controllers; the ST-01 is also supported by
- this driver. It is explained in section 3.9 of the SCSI-HOWTO,
- available from <http://www.tldp.org/docs.html#howto>. If it
- doesn't work out of the box, you may have to change some macros at
- compiletime, which are described in <file:drivers/scsi/seagate.c>.
-
- To compile this driver as a module, choose M here: the
- module will be called seagate.
-
-# definitely looks not 64bit safe:
config SCSI_SIM710
tristate "Simple 53c710 SCSI support (Compaq, NCR machines)"
depends on (EISA || MCA) && SCSI
It currently supports Compaq EISA cards and NCR MCA cards
-config 53C700_IO_MAPPED
- bool
- depends on SCSI_SIM710
- default y
-
config SCSI_SYM53C416
tristate "Symbios 53c416 SCSI support"
depends on ISA && SCSI
tristate "Trantor T128/T128F/T228 SCSI support"
depends on ISA && SCSI
select SCSI_SPI_ATTRS
+ select CHECK_SIGNATURE
---help---
This is support for a SCSI host adapter. It is explained in section
3.11 of the SCSI-HOWTO, available from
config JAZZ_ESP
bool "MIPS JAZZ FAS216 SCSI support"
depends on MACH_JAZZ && SCSI
+ select SCSI_SPI_ATTRS
help
This is the driver for the onboard SCSI host adapter of MIPS Magnum
4000, Acer PICA, Olivetti M700-10 and a few other identical OEM
built-in SCSI controller, say Y. Otherwise, say N.
To compile this driver as a module, choose M here: the
- module will be called wd33c93.
+ module will be called a3000.
config A2091_SCSI
tristate "A2091/A590 WD33C93A support"
say N.
To compile this driver as a module, choose M here: the
- module will be called wd33c93.
+ module will be called a2091.
config GVP11_SCSI
tristate "GVP Series II WD33C93A support"
If you have the Phase5 Fastlane Z3 SCSI controller, or plan to use
one in the near future, say Y to this question. Otherwise, say N.
-config SCSI_AMIGA7XX
- bool "Amiga NCR53c710 SCSI support (EXPERIMENTAL)"
- depends on AMIGA && SCSI && EXPERIMENTAL && BROKEN
+config SCSI_A4000T
+ tristate "A4000T NCR53c710 SCSI support (EXPERIMENTAL)"
+ depends on AMIGA && SCSI && EXPERIMENTAL
+ select SCSI_SPI_ATTRS
help
- Support for various NCR53c710-based SCSI controllers on the Amiga.
+ If you have an Amiga 4000T and have SCSI devices connected to the
+ built-in SCSI controller, say Y. Otherwise, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called a4000t.
+
+config SCSI_ZORRO7XX
+ tristate "Zorro NCR53c710 SCSI support (EXPERIMENTAL)"
+ depends on ZORRO && SCSI && EXPERIMENTAL
+ select SCSI_SPI_ATTRS
+ help
+ Support for various NCR53c710-based SCSI controllers on Zorro
+ expansion boards for the Amiga.
This includes:
- - the builtin SCSI controller on the Amiga 4000T,
- the Amiga 4091 Zorro III SCSI-2 controller,
- the MacroSystem Development's WarpEngine Amiga SCSI-2 controller
(info at
- the SCSI controller on the Phase5 Blizzard PowerUP 603e+
accelerator card for the Amiga 1200,
- the SCSI controller on the GVP Turbo 040/060 accelerator.
- Note that all of the above SCSI controllers, except for the builtin
- SCSI controller on the Amiga 4000T, reside on the Zorro expansion
- bus, so you also have to enable Zorro bus support if you want to use
- them.
config OKTAGON_SCSI
tristate "BSC Oktagon SCSI support (EXPERIMENTAL)"
config ATARI_SCSI
tristate "Atari native SCSI support"
- depends on ATARI && SCSI && BROKEN
+ depends on ATARI && SCSI
select SCSI_SPI_ATTRS
---help---
If you have an Atari with built-in NCR5380 SCSI controller (TT,
single-board computer.
config MVME16x_SCSI
- bool "NCR53C710 SCSI driver for MVME16x"
- depends on MVME16x && SCSI && BROKEN
+ tristate "NCR53C710 SCSI driver for MVME16x"
+ depends on MVME16x && SCSI
select SCSI_SPI_ATTRS
help
The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710
will want to say Y to this question.
config BVME6000_SCSI
- bool "NCR53C710 SCSI driver for BVME6000"
- depends on BVME6000 && SCSI && BROKEN
+ tristate "NCR53C710 SCSI driver for BVME6000"
+ depends on BVME6000 && SCSI
select SCSI_SPI_ATTRS
help
The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710
SCSI controller chip. Almost everyone using one of these boards
will want to say Y to this question.
-config SCSI_NCR53C7xx_FAST
- bool "allow FAST-SCSI [10MHz]"
- depends on SCSI_AMIGA7XX || MVME16x_SCSI || BVME6000_SCSI
- help
- This will enable 10MHz FAST-SCSI transfers with your host
- adapter. Some systems have problems with that speed, so it's safest
- to say N here.
-
config SUN3_SCSI
tristate "Sun3 NCR5380 SCSI"
- depends on SUN3 && SCSI && BROKEN
+ depends on SUN3 && SCSI
select SCSI_SPI_ATTRS
help
This option will enable support for the OBIO (onboard io) NCR5380
config SCSI_SUNESP
tristate "Sparc ESP Scsi Driver"
depends on SBUS && SCSI
+ select SCSI_SPI_ATTRS
help
This is the driver for the Sun ESP SCSI host adapter. The ESP
chipset is present in most SPARC SBUS-based computers.
To compile this driver as a module, choose M here: the
module will be called esp.
-# bool 'Cyberstorm Mk III SCSI support (EXPERIMENTAL)' CONFIG_CYBERSTORMIII_SCSI
-
config ZFCP
tristate "FCP host bus adapter driver for IBM eServer zSeries"
depends on S390 && QDIO && SCSI
This driver is also available as a module. This module will be
called zfcp. If you want to compile it as a module, say M here
- and read <file:Documentation/modules.txt>.
+ and read <file:Documentation/kbuild/modules.txt>.
config SCSI_SRP
tristate "SCSI RDMA Protocol helper library"
To compile this driver as a module, choose M here: the
module will be called libsrp.
-endmenu
+endif # SCSI_LOWLEVEL
source "drivers/scsi/pcmcia/Kconfig"