config RAID_ATTRS
tristate "RAID Transport Class"
default n
+ depends on BLOCK
---help---
Provides RAID
config SCSI
tristate "SCSI device support"
+ depends on BLOCK
---help---
If you want to use a SCSI hard disk, SCSI tape drive, SCSI CD-ROM or
any other SCSI device under Linux, say Y and make sure that you know
However, do not compile this as a module if your root file system
(the one containing the directory /) is located on a SCSI device.
+config SCSI_TGT
+ tristate "SCSI target support"
+ depends on SCSI && EXPERIMENTAL
+ ---help---
+ If you want to use SCSI target mode drivers enable this option.
+ If you choose M, the module will be called scsi_tgt.
+
+config SCSI_NETLINK
+ bool
+ default n
+ select NET
+
config SCSI_PROC_FS
bool "legacy /proc/scsi/ support"
depends on SCSI && PROC_FS
default y
---help---
This option enables support for the various files in
- /proc/scsi. In Linux 2.6 this has been superceeded by
+ /proc/scsi. In Linux 2.6 this has been superseded by
files in sysfs but many legacy applications rely on this.
- If unusure say Y.
+ If unsure say Y.
comment "SCSI support type (disk, tape, CD-ROM)"
depends on SCSI
tristate "SCSI OnStream SC-x0 tape support"
depends on SCSI
---help---
- The OnStream SC-x0 SCSI tape drives can not be driven by the
+ The OnStream SC-x0 SCSI tape drives cannot be driven by the
standard st driver, but instead need this special osst driver and
use the /dev/osstX char device nodes (major 206). Via usb-storage
and ide-scsi, you may be able to drive the USB-x0 and DI-x0 drives
there should be no noticeable performance impact as long as you have
logging turned off.
-menu "SCSI Transport Attributes"
+config SCSI_SCAN_ASYNC
+ bool "Asynchronous SCSI scanning"
+ depends on SCSI
+ help
+ The SCSI subsystem can probe for devices while the rest of the
+ system continues booting, and even probe devices on different
+ busses in parallel, leading to a significant speed-up.
+ If you have built SCSI as modules, enabling this option can
+ be a problem as the devices may not have been found by the
+ time your system expects them to have been. You can load the
+ scsi_wait_scan module to ensure that all scans have completed.
+ If you build your SCSI drivers into the kernel, then everything
+ will work fine if you say Y here.
+
+ You can override this choice by specifying scsi_mod.scan="sync"
+ or "async" on the kernel's command line.
+
+menu "SCSI Transports"
depends on SCSI
config SCSI_SPI_ATTRS
config SCSI_FC_ATTRS
tristate "FiberChannel Transport Attributes"
depends on SCSI
+ select SCSI_NETLINK
help
If you wish to export transport-specific information about
each attached FiberChannel device to sysfs, say Y.
each attached iSCSI device to sysfs, say Y.
Otherwise, say N.
+config SCSI_SAS_ATTRS
+ tristate "SAS Transport Attributes"
+ depends on SCSI
+ help
+ If you wish to export transport-specific information about
+ each attached SAS device to sysfs, say Y.
+
+source "drivers/scsi/libsas/Kconfig"
+
endmenu
menu "SCSI low-level drivers"
config SCSI_AHA152X
tristate "Adaptec AHA152X/2825 support"
depends on ISA && SCSI && !64BIT
+ select SCSI_SPI_ATTRS
---help---
This is a driver for the AHA-1510, AHA-1520, AHA-1522, and AHA-2825
SCSI host adapters. It also works for the AVA-1505, but the IRQ etc.
config SCSI_AACRAID
tristate "Adaptec AACRAID support"
depends on SCSI && PCI
+ help
+ This driver supports a variety of Dell, HP, Adaptec, IBM and
+ ICP storage products. For a list of supported products, refer
+ to <file:Documentation/scsi/aacraid.txt>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called aacraid.
+
source "drivers/scsi/aic7xxx/Kconfig.aic7xxx"
module will be called aic7xxx_old.
source "drivers/scsi/aic7xxx/Kconfig.aic79xx"
+source "drivers/scsi/aic94xx/Kconfig"
# All the I2O code and drivers do not seem to be 64bit safe.
config SCSI_DPT_I2O
config SCSI_ADVANSYS
tristate "AdvanSys SCSI support"
- depends on (ISA || EISA || PCI) && SCSI && BROKEN
+ depends on SCSI
+ depends on ISA || EISA || PCI
+ depends on BROKEN || X86_32
help
This is a driver for all SCSI host adapters manufactured by
AdvanSys. It is documented in the kernel source in
To compile this driver as a module, choose M here: the
module will be called in2000.
-source "drivers/scsi/megaraid/Kconfig.megaraid"
-
-config SCSI_SATA
- tristate "Serial ATA (SATA) support"
- depends on SCSI
- help
- This driver family supports Serial ATA host controllers
- and devices.
-
- If unsure, say N.
-
-config SCSI_SATA_AHCI
- tristate "AHCI SATA support"
- depends on SCSI_SATA && PCI
- help
- This option enables support for AHCI Serial ATA.
-
- If unsure, say N.
-
-config SCSI_SATA_SVW
- tristate "ServerWorks Frodo / Apple K2 SATA support"
- depends on SCSI_SATA && PCI
- help
- This option enables support for Broadcom/Serverworks/Apple K2
- SATA support.
-
- If unsure, say N.
-
-config SCSI_ATA_PIIX
- tristate "Intel PIIX/ICH SATA support"
- depends on SCSI_SATA && PCI
- help
- This option enables support for ICH5 Serial ATA.
- If PATA support was enabled previously, this enables
- support for select Intel PIIX/ICH PATA host controllers.
-
- If unsure, say N.
-
-config SCSI_SATA_MV
- tristate "Marvell SATA support"
- depends on SCSI_SATA && PCI && EXPERIMENTAL
- help
- This option enables support for the Marvell Serial ATA family.
- Currently supports 88SX[56]0[48][01] chips.
-
- If unsure, say N.
-
-config SCSI_SATA_NV
- tristate "NVIDIA SATA support"
- depends on SCSI_SATA && PCI && EXPERIMENTAL
- help
- This option enables support for NVIDIA Serial ATA.
-
- If unsure, say N.
-
-config SCSI_SATA_PROMISE
- tristate "Promise SATA TX2/TX4 support"
- depends on SCSI_SATA && PCI
- help
- This option enables support for Promise Serial ATA TX2/TX4.
-
- If unsure, say N.
-
-config SCSI_SATA_QSTOR
- tristate "Pacific Digital SATA QStor support"
- depends on SCSI_SATA && PCI
- help
- This option enables support for Pacific Digital Serial ATA QStor.
-
- If unsure, say N.
-
-config SCSI_SATA_SX4
- tristate "Promise SATA SX4 support"
- depends on SCSI_SATA && PCI && EXPERIMENTAL
- help
- This option enables support for Promise Serial ATA SX4.
-
- If unsure, say N.
-
-config SCSI_SATA_SIL
- tristate "Silicon Image SATA support"
- depends on SCSI_SATA && PCI && EXPERIMENTAL
- help
- This option enables support for Silicon Image Serial ATA.
-
- If unsure, say N.
-
-config SCSI_SATA_SIS
- tristate "SiS 964/180 SATA support"
- depends on SCSI_SATA && PCI && EXPERIMENTAL
- help
- This option enables support for SiS Serial ATA 964/180.
-
- If unsure, say N.
-
-config SCSI_SATA_ULI
- tristate "ULi Electronics SATA support"
- depends on SCSI_SATA && PCI && EXPERIMENTAL
+config SCSI_ARCMSR
+ tristate "ARECA ARC11X0[PCI-X]/ARC12X0[PCI-EXPRESS] SATA-RAID support"
+ depends on PCI && SCSI
help
- This option enables support for ULi Electronics SATA.
+ This driver supports all of ARECA's SATA RAID controller cards.
+ This is an ARECA-maintained driver by Erich Chen.
+ If you have any problems, please mail to: < erich@areca.com.tw >
+ Areca supports Linux RAID config tools.
- If unsure, say N.
+ < http://www.areca.com.tw >
-config SCSI_SATA_VIA
- tristate "VIA SATA support"
- depends on SCSI_SATA && PCI
- help
- This option enables support for VIA Serial ATA.
+ To compile this driver as a module, choose M here: the
+ module will be called arcmsr (modprobe arcmsr).
- If unsure, say N.
+source "drivers/scsi/megaraid/Kconfig.megaraid"
-config SCSI_SATA_VITESSE
- tristate "VITESSE VSC-7174 SATA support"
- depends on SCSI_SATA && PCI
+config SCSI_HPTIOP
+ tristate "HighPoint RocketRAID 3xxx Controller support"
+ depends on SCSI && PCI
help
- This option enables support for Vitesse VSC7174 Serial ATA.
+ This option enables support for HighPoint RocketRAID 3xxx
+ controllers.
- If unsure, say N.
+ To compile this driver as a module, choose M here; the module
+ will be called hptiop. If unsure, say N.
config SCSI_BUSLOGIC
tristate "BusLogic SCSI support"
substantial, so users of MultiMaster Host Adapters may wish to omit
it.
-#
-# This is marked broken because it uses over 4kB of stack in
-# just two routines:
-# 2076 CpqTsProcessIMQEntry
-# 2052 PeekIMQEntry
-#
-config SCSI_CPQFCTS
- tristate "Compaq Fibre Channel 64-bit/66Mhz HBA support"
- depends on PCI && SCSI && BROKEN
- help
- Say Y here to compile in support for the Compaq StorageWorks Fibre
- Channel 64-bit/66Mhz Host Bus Adapter.
-
config SCSI_DMX3191D
tristate "DMX3191D SCSI support"
depends on PCI && SCSI
+ select SCSI_SPI_ATTRS
help
This is support for Domex DMX3191D SCSI Host Adapters.
config SCSI_DTC3280
tristate "DTC3180/3280 SCSI support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
help
This is support for DTC 3180/3280 SCSI Host Adapters. Please read
the SCSI-HOWTO, available from
config SCSI_GENERIC_NCR5380
tristate "Generic NCR5380/53c400 SCSI PIO support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
---help---
This is a driver for the old NCR 53c80 series of SCSI controllers
on boards using PIO. Most boards such as the Trantor T130 fit this
config SCSI_GENERIC_NCR5380_MMIO
tristate "Generic NCR5380/53c400 SCSI MMIO support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
---help---
This is a driver for the old NCR 53c80 series of SCSI controllers
on boards using memory mapped I/O.
To compile this driver as a module, choose M here: the
module will be called ibmvscsic.
+config SCSI_IBMVSCSIS
+ tristate "IBM Virtual SCSI Server support"
+ depends on PPC_PSERIES && SCSI_TGT && SCSI_SRP
+ help
+ This is the SRP target driver for IBM pSeries virtual environments.
+
+ The userspace component needed to initialize the driver and
+ documentation can be found:
+
+ http://stgt.berlios.de/
+
+ To compile this driver as a module, choose M here: the
+ module will be called ibmvstgt.
+
config SCSI_INITIO
tristate "Initio 9100U(W) support"
depends on PCI && SCSI
config SCSI_PPA
tristate "IOMEGA parallel port (ppa - older drives)"
- depends on SCSI && PARPORT
+ depends on SCSI && PARPORT_PC
---help---
This driver supports older versions of IOMEGA's parallel port ZIP
drive (a 100 MB removable media device).
config SCSI_IMM
tristate "IOMEGA parallel port (imm - newer drives)"
- depends on SCSI && PARPORT
+ depends on SCSI && PARPORT_PC
---help---
This driver supports newer versions of IOMEGA's parallel port ZIP
drive (a 100 MB removable media device).
config SCSI_IZIP_EPP16
bool "ppa/imm option - Use slow (but safe) EPP-16"
- depends on PARPORT && (SCSI_PPA || SCSI_IMM)
+ depends on SCSI_PPA || SCSI_IMM
---help---
EPP (Enhanced Parallel Port) is a standard for parallel ports which
allows them to act as expansion buses that can handle up to 64
config SCSI_IZIP_SLOW_CTR
bool "ppa/imm option - Assume slow parport control register"
- depends on PARPORT && (SCSI_PPA || SCSI_IMM)
+ depends on SCSI_PPA || SCSI_IMM
help
Some parallel ports are known to have excessive delays between
changing the parallel port control register and good data being
depends on SCSI_LASI700
default y
+config SCSI_STEX
+ tristate "Promise SuperTrak EX Series support"
+ depends on PCI && SCSI
+ ---help---
+ This driver supports Promise SuperTrak EX series storage controllers.
+
+ Promise provides Linux RAID configuration utility for these
+ controllers. Please visit <http://www.promise.com> to download.
+
+ To compile this driver as a module, choose M here: the
+ module will be called stex.
+
config SCSI_SYM53C8XX_2
tristate "SYM53C8XX Version 2 SCSI support"
depends on PCI && SCSI
memory using PCI DAC cycles.
config SCSI_SYM53C8XX_DEFAULT_TAGS
- int "default tagged command queue depth"
+ int "Default tagged command queue depth"
depends on SCSI_SYM53C8XX_2
default "16"
help
exceed CONFIG_SCSI_SYM53C8XX_MAX_TAGS.
config SCSI_SYM53C8XX_MAX_TAGS
- int "maximum number of queued commands"
+ int "Maximum number of queued commands"
depends on SCSI_SYM53C8XX_2
default "64"
help
possible. The driver supports up to 256 queued commands per device.
This value is used as a compiled-in hard limit.
-config SCSI_SYM53C8XX_IOMAPPED
- bool "use port IO"
+config SCSI_SYM53C8XX_MMIO
+ bool "Use memory mapped IO"
depends on SCSI_SYM53C8XX_2
+ default y
help
- If you say Y here, the driver will use port IO to access
- the card. This is significantly slower then using memory
- mapped IO. Most people should answer N.
+ Memory mapped IO is faster than Port IO. Most people should
+ answer Y here, but some machines may have problems. If you have
+ to answer N here, please report the problem to the maintainer.
config SCSI_IPR
tristate "IBM Power Linux RAID adapter support"
- depends on PCI && SCSI
+ depends on PCI && SCSI && ATA
select FW_LOADER
---help---
This driver supports the IBM Power Linux family RAID adapters.
config SCSI_IPR_TRACE
bool "enable driver internal trace"
depends on SCSI_IPR
+ default y
help
If you say Y here, the driver will trace all commands issued
to the adapter. Performance impact is minimal. Trace can be
config SCSI_IPR_DUMP
bool "enable adapter dump support"
depends on SCSI_IPR
+ default y
help
If you say Y here, the driver will support adapter crash dump.
If you enable this support, the iprdump daemon can be used
you do not have this SCSI card, so say N.
config SCSI_NCR53C8XX_DEFAULT_TAGS
- int " default tagged command queue depth"
+ int "default tagged command queue depth"
depends on SCSI_ZALON || SCSI_NCR_Q720
default "8"
---help---
There is no safe option other than using good SCSI devices.
config SCSI_NCR53C8XX_MAX_TAGS
- int " maximum number of queued commands"
+ int "maximum number of queued commands"
depends on SCSI_ZALON || SCSI_NCR_Q720
default "32"
---help---
There is no safe option and the default answer is recommended.
config SCSI_NCR53C8XX_SYNC
- int " synchronous transfers frequency in MHz"
+ int "synchronous transfers frequency in MHz"
depends on SCSI_ZALON || SCSI_NCR_Q720
default "20"
---help---
terminations and SCSI conformant devices.
config SCSI_NCR53C8XX_PROFILE
- bool " enable profiling"
+ bool "enable profiling"
depends on SCSI_ZALON || SCSI_NCR_Q720
help
This option allows you to enable profiling information gathering.
The normal answer therefore is N.
config SCSI_NCR53C8XX_NO_DISCONNECT
- bool " not allow targets to disconnect"
+ bool "not allow targets to disconnect"
depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0
help
This option is only provided for safety if you suspect some SCSI
config SCSI_PAS16
tristate "PAS16 SCSI support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
---help---
This is support for a SCSI host adapter. It is explained in section
3.10 of the SCSI-HOWTO, available from
To compile this driver as a module, choose M here: the
module will be called qlogicfas.
-config SCSI_QLOGIC_ISP
- tristate "Qlogic ISP SCSI support (old driver)"
- depends on PCI && SCSI && BROKEN
- ---help---
- This driver works for all QLogic PCI SCSI host adapters (IQ-PCI,
- IQ-PCI-10, IQ_PCI-D) except for the PCI-basic card. (This latter
- card is supported by the "AM53/79C974 PCI SCSI" driver.)
-
- If you say Y here, make sure to choose "BIOS" at the question "PCI
- access mode".
-
- Please read the file <file:Documentation/scsi/qlogicisp.txt>. You
- should also read the SCSI-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here: the
- module will be called qlogicisp.
-
- These days the hardware is also supported by the more modern qla1280
- driver. In doubt use that one instead of qlogicisp.
-
-config SCSI_QLOGIC_FC
- tristate "Qlogic ISP FC SCSI support"
- depends on PCI && SCSI
- help
- This is a driver for the QLogic ISP2100 SCSI-FCP host adapter.
-
- To compile this driver as a module, choose M here: the
- module will be called qlogicfc.
-
config SCSI_QLOGIC_FC_FIRMWARE
bool "Include loadable firmware in driver"
depends on SCSI_QLOGIC_FC
To compile this driver as a module, choose M here: the
module will be called qla1280.
-config SCSI_QLOGIC_1280_1040
- bool "Qlogic QLA 1020/1040 SCSI support"
- depends on SCSI_QLOGIC_1280 && SCSI_QLOGIC_ISP!=y
- help
- Say Y here if you have a QLogic ISP1020/1040 SCSI host adapter and
- do not want to use the old driver. This option enables support in
- the qla1280 driver for those host adapters.
-
config SCSI_QLOGICPTI
tristate "PTI Qlogic, ISP Driver"
depends on SBUS && SCSI
module will be called qlogicpti.
source "drivers/scsi/qla2xxx/Kconfig"
+source "drivers/scsi/qla4xxx/Kconfig"
config SCSI_LPFC
tristate "Emulex LightPulse Fibre Channel Support"
config SCSI_SEAGATE
tristate "Seagate ST-02 and Future Domain TMC-8xx SCSI support"
- depends on X86 && ISA && SCSI && BROKEN
+ depends on X86 && ISA && SCSI
---help---
These are 8-bit SCSI controllers; the ST-01 is also supported by
this driver. It is explained in section 3.9 of the SCSI-HOWTO,
available from <http://www.tldp.org/docs.html#howto>. If it
- doesn't work out of the box, you may have to change some settings in
- <file:drivers/scsi/seagate.h>.
+ doesn't work out of the box, you may have to change some macros at
+ compiletime, which are described in <file:drivers/scsi/seagate.c>.
To compile this driver as a module, choose M here: the
module will be called seagate.
config SCSI_T128
tristate "Trantor T128/T128F/T228 SCSI support"
depends on ISA && SCSI
+ select SCSI_SPI_ATTRS
---help---
This is support for a SCSI host adapter. It is explained in section
3.11 of the SCSI-HOWTO, available from
config ATARI_SCSI
tristate "Atari native SCSI support"
depends on ATARI && SCSI && BROKEN
+ select SCSI_SPI_ATTRS
---help---
If you have an Atari with built-in NCR5380 SCSI controller (TT,
Falcon, ...) say Y to get it supported. Of course also, if you have
config MAC_SCSI
bool "Macintosh NCR5380 SCSI"
depends on MAC && SCSI=y
+ select SCSI_SPI_ATTRS
help
This is the NCR 5380 SCSI controller included on most of the 68030
based Macintoshes. If you have one of these say Y and read the
config MVME147_SCSI
bool "WD33C93 SCSI driver for MVME147"
depends on MVME147 && SCSI=y
+ select SCSI_SPI_ATTRS
help
Support for the on-board SCSI controller on the Motorola MVME147
single-board computer.
config MVME16x_SCSI
bool "NCR53C710 SCSI driver for MVME16x"
depends on MVME16x && SCSI && BROKEN
+ select SCSI_SPI_ATTRS
help
The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710
SCSI controller chip. Almost everyone using one of these boards
config BVME6000_SCSI
bool "NCR53C710 SCSI driver for BVME6000"
depends on BVME6000 && SCSI && BROKEN
+ select SCSI_SPI_ATTRS
help
The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710
SCSI controller chip. Almost everyone using one of these boards
config SUN3_SCSI
tristate "Sun3 NCR5380 SCSI"
- depends on SUN3 && SCSI && BROKEN
+ depends on SUN3 && SCSI
+ select SCSI_SPI_ATTRS
help
This option will enable support for the OBIO (onboard io) NCR5380
SCSI controller found in the Sun 3/50 and 3/60, as well as for
config ZFCP
tristate "FCP host bus adapter driver for IBM eServer zSeries"
- depends on ARCH_S390 && QDIO && SCSI
+ depends on S390 && QDIO && SCSI
select SCSI_FC_ATTRS
help
If you want to access SCSI devices attached to your IBM eServer
called zfcp. If you want to compile it as a module, say M here
and read <file:Documentation/modules.txt>.
+config SCSI_SRP
+ tristate "SCSI RDMA Protocol helper library"
+ depends on SCSI && PCI
+ select SCSI_TGT
+ help
+ If you wish to use SRP target drivers, say Y.
+
+ To compile this driver as a module, choose M here: the
+ module will be called libsrp.
+
endmenu
source "drivers/scsi/pcmcia/Kconfig"