[SCSI] iscsi: data digest calculation fix

[safe/jmp/linux-2.6] / drivers / scsi / Kconfig

diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index c76a3b8..20dd85a 100644 (file)
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -235,6 +235,13 @@ config SCSI_ISCSI_ATTRS
          each attached iSCSI device to sysfs, say Y.
          Otherwise, say N.
 
+config SCSI_SAS_ATTRS
+       tristate "SAS Transport Attributes"
+       depends on SCSI
+       help
+         If you wish to export transport-specific information about
+         each attached SAS device to sysfs, say Y.
+
 endmenu
 
 menu "SCSI low-level drivers"
@@ -490,7 +497,7 @@ config SCSI_ATA_PIIX
          If unsure, say N.
 
 config SCSI_SATA_MV
-       tristate "Marvell SATA support"
+       tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
        help
          This option enables support for the Marvell Serial ATA family.
@@ -506,11 +513,11 @@ config SCSI_SATA_NV
 
          If unsure, say N.
 
-config SCSI_SATA_PROMISE
-       tristate "Promise SATA TX2/TX4 support"
+config SCSI_PDC_ADMA
+       tristate "Pacific Digital ADMA support"
        depends on SCSI_SATA && PCI
        help
-         This option enables support for Promise Serial ATA TX2/TX4.
+         This option enables support for Pacific Digital ADMA controllers
 
          If unsure, say N.
 
@@ -522,6 +529,14 @@ config SCSI_SATA_QSTOR
 
          If unsure, say N.
 
+config SCSI_SATA_PROMISE
+       tristate "Promise SATA TX2/TX4 support"
+       depends on SCSI_SATA && PCI
+       help
+         This option enables support for Promise Serial ATA TX2/TX4.
+
+         If unsure, say N.
+
 config SCSI_SATA_SX4
        tristate "Promise SATA SX4 support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
@@ -538,6 +553,14 @@ config SCSI_SATA_SIL
 
          If unsure, say N.
 
+config SCSI_SATA_SIL24
+       tristate "Silicon Image 3124/3132 SATA support"
+       depends on SCSI_SATA && PCI && EXPERIMENTAL
+       help
+         This option enables support for Silicon Image 3124/3132 Serial ATA.
+
+         If unsure, say N.
+
 config SCSI_SATA_SIS
        tristate "SiS 964/180 SATA support"
        depends on SCSI_SATA && PCI && EXPERIMENTAL
@@ -570,6 +593,11 @@ config SCSI_SATA_VITESSE
 
          If unsure, say N.
 
+config SCSI_SATA_INTEL_COMBINED
+       bool
+       depends on IDE=y && !BLK_DEV_IDE_SATA && (SCSI_SATA_AHCI || SCSI_ATA_PIIX)
+       default y
+
 config SCSI_BUSLOGIC
        tristate "BusLogic SCSI support"
        depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API
@@ -592,19 +620,6 @@ config SCSI_OMIT_FLASHPOINT
          substantial, so users of MultiMaster Host Adapters may wish to omit
          it.
 
-#
-# This is marked broken because it uses over 4kB of stack in
-# just two routines:
-#     2076  CpqTsProcessIMQEntry
-#     2052  PeekIMQEntry
-#
-config SCSI_CPQFCTS
-       tristate "Compaq Fibre Channel 64-bit/66Mhz HBA support"
-       depends on PCI && SCSI && BROKEN
-       help
-         Say Y here to compile in support for the Compaq StorageWorks Fibre
-         Channel 64-bit/66Mhz Host Bus Adapter.
-
 config SCSI_DMX3191D
        tristate "DMX3191D SCSI support"
        depends on PCI && SCSI
@@ -1280,27 +1295,6 @@ config SCSI_QLOGIC_FAS
          To compile this driver as a module, choose M here: the
          module will be called qlogicfas.
 
-config SCSI_QLOGIC_ISP
-       tristate "Qlogic ISP SCSI support (old driver)"
-       depends on PCI && SCSI && BROKEN
-       ---help---
-         This driver works for all QLogic PCI SCSI host adapters (IQ-PCI,
-         IQ-PCI-10, IQ_PCI-D) except for the PCI-basic card.  (This latter
-         card is supported by the "AM53/79C974 PCI SCSI" driver.)
-
-         If you say Y here, make sure to choose "BIOS" at the question "PCI
-         access mode".
-
-         Please read the file <file:Documentation/scsi/qlogicisp.txt>.  You
-         should also read the SCSI-HOWTO, available from
-         <http://www.tldp.org/docs.html#howto>.
-
-         To compile this driver as a module, choose M here: the
-         module will be called qlogicisp.
-
-         These days the hardware is also supported by the more modern qla1280
-         driver.  In doubt use that one instead of qlogicisp.
-
 config SCSI_QLOGIC_FC
        tristate "Qlogic ISP FC SCSI support"
        depends on PCI && SCSI
@@ -1327,14 +1321,6 @@ config SCSI_QLOGIC_1280
          To compile this driver as a module, choose M here: the
          module will be called qla1280.
 
-config SCSI_QLOGIC_1280_1040
-       bool "Qlogic QLA 1020/1040 SCSI support"
-       depends on SCSI_QLOGIC_1280 && SCSI_QLOGIC_ISP!=y
-       help
-         Say Y here if you have a QLogic ISP1020/1040 SCSI host adapter and
-         do not want to use the old driver.  This option enables support in
-         the qla1280 driver for those host adapters.
-
 config SCSI_QLOGICPTI
        tristate "PTI Qlogic, ISP Driver"
        depends on SBUS && SCSI