*
*/
+#define KMSG_COMPONENT "dasd"
+
#include <linux/timer.h>
#include <linux/slab.h>
#include <asm/idals.h>
struct dasd_device *device = erp->startdev;
unsigned long flags;
- DEV_MESSAGE(KERN_INFO, device,
+ DBF_DEV_EVENT(DBF_INFO, device,
"blocking request queue for %is", expires/HZ);
spin_lock_irqsave(get_ccwdev_lock(device->cdev), flags);
} else {
/* issue a message and wait for 'device ready' interrupt */
- DEV_MESSAGE(KERN_ERR, device, "%s",
+ dev_err(&device->cdev->dev,
"is offline or not installed - "
- "INTERVENTION REQUIRED!!");
+ "INTERVENTION REQUIRED!!\n");
dasd_3990_erp_block_queue(erp, 60*HZ);
}
if ((erp->lpm & opm) != 0x00) {
- DEV_MESSAGE(KERN_DEBUG, device,
+ DBF_DEV_EVENT(DBF_WARNING, device,
"try alternate lpm=%x (lpum=%x / opm=%x)",
erp->lpm, erp->irb.esw.esw0.sublog.lpum, opm);
erp->status = DASD_CQR_FILLED;
erp->retries = 10;
} else {
- DEV_MESSAGE(KERN_ERR, device,
- "No alternate channel path left (lpum=%x / "
- "opm=%x) -> permanent error",
- erp->irb.esw.esw0.sublog.lpum, opm);
+ dev_err(&device->cdev->dev,
+ "The DASD cannot be reached on any path (lpum=%x"
+ "/opm=%x)\n", erp->irb.esw.esw0.sublog.lpum, opm);
/* post request with permanent error */
erp->status = DASD_CQR_FAILED;
sizeof(struct DCTL_data),
device);
if (IS_ERR(dctl_cqr)) {
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "Unable to allocate DCTL-CQR");
+ dev_err(&device->cdev->dev,
+ "Unable to allocate DCTL-CQR\n");
erp->status = DASD_CQR_FAILED;
return erp;
}
/* interrupt (this enables easier enqueing of the cqr) */
if (erp->function != dasd_3990_erp_action_4) {
- DEV_MESSAGE(KERN_INFO, device, "%s",
+ DBF_DEV_EVENT(DBF_INFO, device, "%s",
"dasd_3990_erp_action_4: first time retry");
erp->retries = 256;
} else {
if (sense && (sense[25] == 0x1D)) { /* state change pending */
- DEV_MESSAGE(KERN_INFO, device,
+ DBF_DEV_EVENT(DBF_INFO, device,
"waiting for state change pending "
"interrupt, %d retries left",
erp->retries);
dasd_3990_erp_block_queue(erp, 30*HZ);
} else if (sense && (sense[25] == 0x1E)) { /* busy */
- DEV_MESSAGE(KERN_INFO, device,
+ DBF_DEV_EVENT(DBF_INFO, device,
"busy - redriving request later, "
"%d retries left",
erp->retries);
dasd_3990_erp_block_queue(erp, HZ);
} else {
-
/* no state change pending - retry */
- DEV_MESSAGE (KERN_INFO, device,
+ DBF_DEV_EVENT(DBF_INFO, device,
"redriving request immediately, "
"%d retries left",
erp->retries);
struct dasd_device *device = erp->startdev;
char msg_format = (sense[7] & 0xF0);
char msg_no = (sense[7] & 0x0F);
+ char errorstring[ERRORLENGTH];
switch (msg_format) {
case 0x00: /* Format 0 - Program or System Checks */
case 0x00: /* No Message */
break;
case 0x01:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 0 - Invalid Command");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 0 - Invalid Command\n");
break;
case 0x02:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - Invalid Command "
- "Sequence");
+ "Sequence\n");
break;
case 0x03:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - CCW Count less than "
- "required");
+ "required\n");
break;
case 0x04:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 0 - Invalid Parameter");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 0 - Invalid Parameter\n");
break;
case 0x05:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 0 - Diagnostic of Sepecial"
- " Command Violates File Mask");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 0 - Diagnostic of Special"
+ " Command Violates File Mask\n");
break;
case 0x07:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - Channel Returned with "
- "Incorrect retry CCW");
+ "Incorrect retry CCW\n");
break;
case 0x08:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 0 - Reset Notification");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 0 - Reset Notification\n");
break;
case 0x09:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 0 - Storage Path Restart");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 0 - Storage Path Restart\n");
break;
case 0x0A:
- DEV_MESSAGE(KERN_WARNING, device,
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - Channel requested "
- "... %02x", sense[8]);
+ "... %02x\n", sense[8]);
break;
case 0x0B:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - Invalid Defective/"
- "Alternate Track Pointer");
+ "Alternate Track Pointer\n");
break;
case 0x0C:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - DPS Installation "
- "Check");
+ "Check\n");
break;
case 0x0E:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - Command Invalid on "
- "Secondary Address");
+ "Secondary Address\n");
break;
case 0x0F:
- DEV_MESSAGE(KERN_WARNING, device,
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - Status Not As "
- "Required: reason %02x", sense[8]);
+ "Required: reason %02x\n",
+ sense[8]);
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 0 - Reseved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 0 - Reserved\n");
}
} else {
switch (msg_no) {
case 0x00: /* No Message */
break;
case 0x01:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 0 - Device Error Source");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 0 - Device Error "
+ "Source\n");
break;
case 0x02:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 0 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 0 - Reserved\n");
break;
case 0x03:
- DEV_MESSAGE(KERN_WARNING, device,
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - Device Fenced - "
- "device = %02x", sense[4]);
+ "device = %02x\n", sense[4]);
break;
case 0x04:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 0 - Data Pinned for "
- "Device");
+ "Device\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 0 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 0 - Reserved\n");
}
}
break;
case 0x00: /* No Message */
break;
case 0x01:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 1 - Device Status 1 not as "
- "expected");
+ "expected\n");
break;
case 0x03:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 1 - Index missing");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 1 - Index missing\n");
break;
case 0x04:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 1 - Interruption cannot be reset");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 1 - Interruption cannot be "
+ "reset\n");
break;
case 0x05:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 1 - Device did not respond to "
- "selection");
+ "selection\n");
break;
case 0x06:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 1 - Device check-2 error or Set "
- "Sector is not complete");
+ "Sector is not complete\n");
break;
case 0x07:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 1 - Head address does not "
- "compare");
+ "compare\n");
break;
case 0x08:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 1 - Device status 1 not valid");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 1 - Device status 1 not valid\n");
break;
case 0x09:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 1 - Device not ready");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 1 - Device not ready\n");
break;
case 0x0A:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 1 - Track physical address did "
- "not compare");
+ "not compare\n");
break;
case 0x0B:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 1 - Missing device address bit");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 1 - Missing device address bit\n");
break;
case 0x0C:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 1 - Drive motor switch is off");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 1 - Drive motor switch is off\n");
break;
case 0x0D:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 1 - Seek incomplete");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 1 - Seek incomplete\n");
break;
case 0x0E:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 1 - Cylinder address did not "
- "compare");
+ "compare\n");
break;
case 0x0F:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 1 - Offset active cannot be "
- "reset");
+ "reset\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 1 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 1 - Reserved\n");
}
break;
case 0x20: /* Format 2 - 3990 Equipment Checks */
switch (msg_no) {
case 0x08:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 2 - 3990 check-2 error");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 2 - 3990 check-2 error\n");
break;
case 0x0E:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 2 - Support facility errors");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 2 - Support facility errors\n");
break;
case 0x0F:
- DEV_MESSAGE(KERN_WARNING, device,
- "FORMAT 2 - Microcode detected error %02x",
- sense[8]);
+ dev_warn(&device->cdev->dev,
+ "FORMAT 2 - Microcode detected error "
+ "%02x\n",
+ sense[8]);
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 2 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 2 - Reserved\n");
}
break;
case 0x30: /* Format 3 - 3990 Control Checks */
switch (msg_no) {
case 0x0F:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 3 - Allegiance terminated");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 3 - Allegiance terminated\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 3 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 3 - Reserved\n");
}
break;
case 0x40: /* Format 4 - Data Checks */
switch (msg_no) {
case 0x00:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 4 - Home address area error");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 4 - Home address area error\n");
break;
case 0x01:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 4 - Count area error");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 4 - Count area error\n");
break;
case 0x02:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 4 - Key area error");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 4 - Key area error\n");
break;
case 0x03:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 4 - Data area error");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 4 - Data area error\n");
break;
case 0x04:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - No sync byte in home address "
- "area");
+ "area\n");
break;
case 0x05:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - No sync byte in count address "
- "area");
+ "area\n");
break;
case 0x06:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 4 - No sync byte in key area");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 4 - No sync byte in key area\n");
break;
case 0x07:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 4 - No sync byte in data area");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 4 - No sync byte in data area\n");
break;
case 0x08:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - Home address area error; "
- "offset active");
+ "offset active\n");
break;
case 0x09:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - Count area error; offset "
- "active");
+ "active\n");
break;
case 0x0A:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - Key area error; offset "
- "active");
+ "active\n");
break;
case 0x0B:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - Data area error; "
- "offset active");
+ "offset active\n");
break;
case 0x0C:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - No sync byte in home "
- "address area; offset active");
+ "address area; offset active\n");
break;
case 0x0D:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - No syn byte in count "
- "address area; offset active");
+ "address area; offset active\n");
break;
case 0x0E:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - No sync byte in key area; "
- "offset active");
+ "offset active\n");
break;
case 0x0F:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 4 - No syn byte in data area; "
- "offset active");
+ "offset active\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 4 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 4 - Reserved\n");
}
break;
case 0x50: /* Format 5 - Data Check with displacement information */
switch (msg_no) {
case 0x00:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 5 - Data Check in the "
- "home address area");
+ "home address area\n");
break;
case 0x01:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 5 - Data Check in the count area");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 5 - Data Check in the count "
+ "area\n");
break;
case 0x02:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 5 - Data Check in the key area");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 5 - Data Check in the key area\n");
break;
case 0x03:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 5 - Data Check in the data area");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 5 - Data Check in the data "
+ "area\n");
break;
case 0x08:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 5 - Data Check in the "
- "home address area; offset active");
+ "home address area; offset active\n");
break;
case 0x09:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 5 - Data Check in the count area; "
- "offset active");
+ "offset active\n");
break;
case 0x0A:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 5 - Data Check in the key area; "
- "offset active");
+ "offset active\n");
break;
case 0x0B:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 5 - Data Check in the data area; "
- "offset active");
+ "offset active\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 5 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 5 - Reserved\n");
}
break;
case 0x60: /* Format 6 - Usage Statistics/Overrun Errors */
switch (msg_no) {
case 0x00:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 6 - Overrun on channel A");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 6 - Overrun on channel A\n");
break;
case 0x01:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 6 - Overrun on channel B");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 6 - Overrun on channel B\n");
break;
case 0x02:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 6 - Overrun on channel C");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 6 - Overrun on channel C\n");
break;
case 0x03:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 6 - Overrun on channel D");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 6 - Overrun on channel D\n");
break;
case 0x04:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 6 - Overrun on channel E");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 6 - Overrun on channel E\n");
break;
case 0x05:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 6 - Overrun on channel F");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 6 - Overrun on channel F\n");
break;
case 0x06:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 6 - Overrun on channel G");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 6 - Overrun on channel G\n");
break;
case 0x07:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 6 - Overrun on channel H");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 6 - Overrun on channel H\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 6 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 6 - Reserved\n");
}
break;
case 0x70: /* Format 7 - Device Connection Control Checks */
switch (msg_no) {
case 0x00:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - RCC initiated by a connection "
- "check alert");
+ "check alert\n");
break;
case 0x01:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - RCC 1 sequence not "
- "successful");
+ "successful\n");
break;
case 0x02:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - RCC 1 and RCC 2 sequences not "
- "successful");
+ "successful\n");
break;
case 0x03:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - Invalid tag-in during "
- "selection sequence");
+ "selection sequence\n");
break;
case 0x04:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 7 - extra RCC required");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 7 - extra RCC required\n");
break;
case 0x05:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - Invalid DCC selection "
- "response or timeout");
+ "response or timeout\n");
break;
case 0x06:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - Missing end operation; device "
- "transfer complete");
+ "transfer complete\n");
break;
case 0x07:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - Missing end operation; device "
- "transfer incomplete");
+ "transfer incomplete\n");
break;
case 0x08:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - Invalid tag-in for an "
- "immediate command sequence");
+ "immediate command sequence\n");
break;
case 0x09:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - Invalid tag-in for an "
- "extended command sequence");
+ "extended command sequence\n");
break;
case 0x0A:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - 3990 microcode time out when "
- "stopping selection");
+ "stopping selection\n");
break;
case 0x0B:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - No response to selection "
- "after a poll interruption");
+ "after a poll interruption\n");
break;
case 0x0C:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - Permanent path error (DASD "
- "controller not available)");
+ "controller not available)\n");
break;
case 0x0D:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 7 - DASD controller not available"
- " on disconnected command chain");
+ " on disconnected command chain\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 7 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 7 - Reserved\n");
}
break;
switch (msg_no) {
case 0x00: /* No Message */
case 0x01:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 8 - Error correction code "
- "hardware fault");
+ "hardware fault\n");
break;
case 0x03:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 8 - Unexpected end operation "
- "response code");
+ "response code\n");
break;
case 0x04:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 8 - End operation with transfer "
- "count not zero");
+ "count not zero\n");
break;
case 0x05:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 8 - End operation with transfer "
- "count zero");
+ "count zero\n");
break;
case 0x06:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 8 - DPS checks after a system "
- "reset or selective reset");
+ "reset or selective reset\n");
break;
case 0x07:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 8 - DPS cannot be filled");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 8 - DPS cannot be filled\n");
break;
case 0x08:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 8 - Short busy time-out during "
- "device selection");
+ "device selection\n");
break;
case 0x09:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 8 - DASD controller failed to "
- "set or reset the long busy latch");
+ "set or reset the long busy latch\n");
break;
case 0x0A:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 8 - No interruption from device "
- "during a command chain");
+ "during a command chain\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 8 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 8 - Reserved\n");
}
break;
case 0x00:
break; /* No Message */
case 0x06:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 9 - Device check-2 error");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 9 - Device check-2 error\n");
break;
case 0x07:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 9 - Head address did not compare");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 9 - Head address did not "
+ "compare\n");
break;
case 0x0A:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 9 - Track physical address did "
- "not compare while oriented");
+ "not compare while oriented\n");
break;
case 0x0E:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT 9 - Cylinder address did not "
- "compare");
+ "compare\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT 9 - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT 9 - Reserved\n");
}
break;
case 0xF0: /* Format F - Cache Storage Checks */
switch (msg_no) {
case 0x00:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT F - Operation Terminated");
+ dev_warn(&device->cdev->dev,
+ "FORMAT F - Operation Terminated\n");
break;
case 0x01:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT F - Subsystem Processing Error");
+ dev_warn(&device->cdev->dev,
+ "FORMAT F - Subsystem Processing Error\n");
break;
case 0x02:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT F - Cache or nonvolatile storage "
- "equipment failure");
+ "equipment failure\n");
break;
case 0x04:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT F - Caching terminated");
+ dev_warn(&device->cdev->dev,
+ "FORMAT F - Caching terminated\n");
break;
case 0x06:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT F - Cache fast write access not "
- "authorized");
+ "authorized\n");
break;
case 0x07:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT F - Track format incorrect");
+ dev_warn(&device->cdev->dev,
+ "FORMAT F - Track format incorrect\n");
break;
case 0x09:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT F - Caching reinitiated");
+ dev_warn(&device->cdev->dev,
+ "FORMAT F - Caching reinitiated\n");
break;
case 0x0A:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT F - Nonvolatile storage "
- "terminated");
+ "terminated\n");
break;
case 0x0B:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT F - Volume is suspended duplex");
+ dev_warn(&device->cdev->dev,
+ "FORMAT F - Volume is suspended duplex\n");
/* call extended error reporting (EER) */
dasd_eer_write(device, erp->refers,
DASD_EER_PPRCSUSPEND);
break;
case 0x0C:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT F - Subsystem status connot be "
- "determined");
+ dev_warn(&device->cdev->dev,
+ "FORMAT F - Subsystem status cannot be "
+ "determined\n");
break;
case 0x0D:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
+ dev_warn(&device->cdev->dev,
"FORMAT F - Caching status reset to "
- "default");
+ "default\n");
break;
case 0x0E:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT F - DASD Fast Write inhibited");
+ dev_warn(&device->cdev->dev,
+ "FORMAT F - DASD Fast Write inhibited\n");
break;
default:
- DEV_MESSAGE(KERN_WARNING, device, "%s",
- "FORMAT D - Reserved");
+ dev_warn(&device->cdev->dev,
+ "FORMAT D - Reserved\n");
}
break;
- default: /* unknown message format - should not happen */
- DEV_MESSAGE (KERN_WARNING, device,
- "unknown message format %02x",
- msg_format);
+ default: /* unknown message format - should not happen
+ internal error 03 - unknown message format */
+ snprintf(errorstring, ERRORLENGTH, "03 %x02", msg_format);
+ dev_err(&device->cdev->dev,
+ "An error occurred in the DASD device driver, "
+ "reason=%s\n", errorstring);
break;
} /* end switch message format */
/* env data present (ACTION 10 - retry should work) */
if (sense[2] & SNS2_ENV_DATA_PRESENT) {
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Command Reject - environmental data present");
dasd_3990_handle_env_data(erp, sense);
erp->retries = 5;
} else {
- /* fatal error - set status to FAILED */
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "Command Reject - Fatal error");
+ /* fatal error - set status to FAILED
+ internal error 09 - Command Reject */
+ dev_err(&device->cdev->dev, "An error occurred in the DASD "
+ "device driver, reason=%s\n", "09");
erp = dasd_3990_erp_cleanup(erp, DASD_CQR_FAILED);
}
} else {
/* issue a message and wait for 'device ready' interrupt */
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"bus out parity error or BOPC requested by "
"channel");
erp->function = dasd_3990_erp_equip_check;
if (sense[1] & SNS1_WRITE_INHIBITED) {
+ dev_info(&device->cdev->dev,
+ "Write inhibited path encountered\n");
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
- "Write inhibited path encountered");
-
- /* vary path offline */
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "Path should be varied off-line. "
- "This is not implemented yet \n - please report "
- "to linux390@de.ibm.com");
+ /* vary path offline
+ internal error 04 - Path should be varied off-line.*/
+ dev_err(&device->cdev->dev, "An error occurred in the DASD "
+ "device driver, reason=%s\n", "04");
erp = dasd_3990_erp_action_1(erp);
} else if (sense[2] & SNS2_ENV_DATA_PRESENT) {
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Equipment Check - " "environmental data present");
dasd_3990_handle_env_data(erp, sense);
} else if (sense[1] & SNS1_PERM_ERR) {
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Equipment Check - retry exhausted or "
"undesirable");
} else {
/* all other equipment checks - Action 5 */
/* rest is done when retries == 0 */
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Equipment check or processing error");
erp = dasd_3990_erp_action_5(erp);
if (sense[2] & SNS2_CORRECTABLE) { /* correctable data check */
/* issue message that the data has been corrected */
- DEV_MESSAGE(KERN_EMERG, device, "%s",
+ dev_emerg(&device->cdev->dev,
"Data recovered during retry with PCI "
- "fetch mode active");
+ "fetch mode active\n");
/* not possible to handle this situation in Linux */
panic("No way to inform application about the possibly "
} else if (sense[2] & SNS2_ENV_DATA_PRESENT) {
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Uncorrectable data check recovered secondary "
"addr of duplex pair");
} else if (sense[1] & SNS1_PERM_ERR) {
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Uncorrectable data check with internal "
"retry exhausted");
} else {
/* all other data checks */
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Uncorrectable data check with retry count "
"exhausted...");
erp->function = dasd_3990_erp_overrun;
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Overrun - service overrun or overrun"
" error requested by channel");
if (sense[2] & SNS2_ENV_DATA_PRESENT) {
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Track format error when destaging or "
"staging data");
erp = dasd_3990_erp_action_4(erp, sense);
} else {
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "Invalid Track Format - Fatal error");
+ /* internal error 06 - The track format is not valid*/
+ dev_err(&device->cdev->dev,
+ "An error occurred in the DASD device driver, "
+ "reason=%s\n", "06");
erp = dasd_3990_erp_cleanup(erp, DASD_CQR_FAILED);
}
struct dasd_device *device = default_erp->startdev;
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "End-of-Cylinder - must never happen");
+ dev_err(&device->cdev->dev,
+ "The cylinder data for accessing the DASD is inconsistent\n");
/* implement action 7 - BUG */
return dasd_3990_erp_cleanup(default_erp, DASD_CQR_FAILED);
erp->function = dasd_3990_erp_env_data;
- DEV_MESSAGE(KERN_DEBUG, device, "%s", "Environmental data present");
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s", "Environmental data present");
dasd_3990_handle_env_data(erp, sense);
struct dasd_device *device = default_erp->startdev;
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "No Record Found - Fatal error ");
+ dev_err(&device->cdev->dev,
+ "The specified record was not found\n");
return dasd_3990_erp_cleanup(default_erp, DASD_CQR_FAILED);
struct dasd_device *device = erp->startdev;
- DEV_MESSAGE(KERN_ERR, device, "%s", "File Protected");
+ dev_err(&device->cdev->dev, "Accessing the DASD failed because of "
+ "a hardware error\n");
return dasd_3990_erp_cleanup(erp, DASD_CQR_FAILED);
if (cqr->block &&
(cqr->block->base != cqr->startdev)) {
if (cqr->startdev->features & DASD_FEATURE_ERPLOG) {
- DEV_MESSAGE(KERN_ERR, cqr->startdev,
+ DBF_DEV_EVENT(DBF_ERR, cqr->startdev,
"ERP on alias device for request %p,"
" recover on base device %s", cqr,
dev_name(&cqr->block->base->cdev->dev));
erp->retries = 256;
erp->function = dasd_3990_erp_action_10_32;
- DEV_MESSAGE(KERN_DEBUG, device, "%s", "Perform logging requested");
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s", "Perform logging requested");
return erp;
char *LO_data; /* LO_eckd_data_t */
struct ccw1 *ccw, *oldccw;
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Write not finished because of unexpected condition");
default_erp->function = dasd_3990_erp_action_1B_32;
/* for imprecise ending just do default erp */
if (sense[1] & 0x01) {
-
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Imprecise ending is set - just retry");
return default_erp;
cpa = default_erp->refers->irb.scsw.cmd.cpa;
if (cpa == 0) {
-
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Unable to determine address of the CCW "
"to be restarted");
sizeof(struct LO_eckd_data), device);
if (IS_ERR(erp)) {
- DEV_MESSAGE(KERN_ERR, device, "%s", "Unable to allocate ERP");
+ /* internal error 01 - Unable to allocate ERP */
+ dev_err(&device->cdev->dev, "An error occurred in the DASD "
+ "device driver, reason=%s\n", "01");
return dasd_3990_erp_cleanup(default_erp, DASD_CQR_FAILED);
}
LO_data = erp->data + sizeof(struct DE_eckd_data);
if ((sense[3] == 0x01) && (LO_data[1] & 0x01)) {
-
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "BUG - this should not happen");
-
+ /* should not */
return dasd_3990_erp_cleanup(default_erp, DASD_CQR_FAILED);
}
char *LO_data; /* struct LO_eckd_data */
struct ccw1 *ccw;
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Write not finished because of unexpected condition"
" - follow on");
/* for imprecise ending just do default erp */
if (sense[1] & 0x01) {
-
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Imprecise ending is set - just retry");
previous_erp->status = DASD_CQR_FILLED;
cpa = previous_erp->irb.scsw.cmd.cpa;
if (cpa == 0) {
-
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
- "Unable to determine address of the CCW "
- "to be restarted");
+ /* internal error 02 -
+ Unable to determine address of the CCW to be restarted */
+ dev_err(&device->cdev->dev, "An error occurred in the DASD "
+ "device driver, reason=%s\n", "02");
previous_erp->status = DASD_CQR_FAILED;
LO_data = erp->data + sizeof(struct DE_eckd_data);
if ((sense[3] == 0x01) && (LO_data[1] & 0x01)) {
-
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "BUG - this should not happen");
-
+ /* should not happen */
previous_erp->status = DASD_CQR_FAILED;
return previous_erp;
if ((sense[25] & DASD_SENSE_BIT_1) && (sense[26] & DASD_SENSE_BIT_2)) {
- /* set to suspended duplex state then restart */
+ /* set to suspended duplex state then restart
+ internal error 05 - Set device to suspended duplex state
+ should be done */
struct dasd_device *device = erp->startdev;
-
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "Set device to suspended duplex state should be "
- "done!\n"
- "This is not implemented yet (for compound ERP)"
- " - please report to linux390@de.ibm.com");
+ dev_err(&device->cdev->dev,
+ "An error occurred in the DASD device driver, "
+ "reason=%s\n", "05");
}
{
/* print message according to log or message to operator mode */
if ((sense[24] & DASD_SIM_MSG_TO_OP) || (sense[1] & 0x10)) {
-
/* print SIM SRC from RefCode */
- DEV_MESSAGE(KERN_ERR, device, "SIM - SRC: "
- "%02x%02x%02x%02x", sense[22],
+ dev_err(&device->cdev->dev, "SIM - SRC: "
+ "%02x%02x%02x%02x\n", sense[22],
sense[23], sense[11], sense[12]);
} else if (sense[24] & DASD_SIM_LOG) {
/* print SIM SRC Refcode */
- DEV_MESSAGE(KERN_WARNING, device, "SIM - SRC: "
- "%02x%02x%02x%02x", sense[22],
+ dev_warn(&device->cdev->dev, "log SIM - SRC: "
+ "%02x%02x%02x%02x\n", sense[22],
sense[23], sense[11], sense[12]);
}
}
switch (sense[25]) {
case 0x00: /* success - use default ERP for retries */
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_DEBUG, device, "%s",
"ERP called for successful request"
" - just retry");
break;
case 0x01: /* fatal error */
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "Retry not recommended - Fatal error");
+ dev_err(&device->cdev->dev,
+ "ERP failed for the DASD\n");
erp = dasd_3990_erp_cleanup(erp, DASD_CQR_FAILED);
break;
erp = dasd_3990_erp_int_req(erp);
break;
- case 0x0F: /* length mismatch during update write command */
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "update write command error - should not "
- "happen;\n"
- "Please send this message together with "
- "the above sense data to linux390@de."
- "ibm.com");
+ case 0x0F: /* length mismatch during update write command
+ internal error 08 - update write command error*/
+ dev_err(&device->cdev->dev, "An error occurred in the "
+ "DASD device driver, reason=%s\n", "08");
erp = dasd_3990_erp_cleanup(erp, DASD_CQR_FAILED);
break;
erp = dasd_3990_erp_action_10_32(erp, sense);
break;
- case 0x15: /* next track outside defined extend */
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "next track outside defined extend - "
- "should not happen;\n"
- "Please send this message together with "
- "the above sense data to linux390@de."
- "ibm.com");
+ case 0x15: /* next track outside defined extend
+ internal error 07 - The next track is not
+ within the defined storage extent */
+ dev_err(&device->cdev->dev,
+ "An error occurred in the DASD device driver, "
+ "reason=%s\n", "07");
erp = dasd_3990_erp_cleanup(erp, DASD_CQR_FAILED);
break;
break;
case 0x1C: /* invalid data */
- DEV_MESSAGE(KERN_EMERG, device, "%s",
+ dev_emerg(&device->cdev->dev,
"Data recovered during retry with PCI "
- "fetch mode active");
+ "fetch mode active\n");
/* not possible to handle this situation in Linux */
panic
break;
case 0x1D: /* state-change pending */
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"A State change pending condition exists "
"for the subsystem or device");
break;
case 0x1E: /* busy */
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"Busy condition exists "
"for the subsystem or device");
erp = dasd_3990_erp_action_4(erp, sense);
if (scsw_cstat(&erp->refers->irb.scsw) & (SCHN_STAT_INTF_CTRL_CHK
| SCHN_STAT_CHN_CTRL_CHK)) {
- DEV_MESSAGE(KERN_DEBUG, device, "%s",
+ DBF_DEV_EVENT(DBF_WARNING, device, "%s",
"channel or interface control check");
erp = dasd_3990_erp_action_4(erp, NULL);
}
cplength, datasize, device);
if (IS_ERR(erp)) {
if (cqr->retries <= 0) {
- DEV_MESSAGE(KERN_ERR, device, "%s",
+ DBF_DEV_EVENT(DBF_ERR, device, "%s",
"Unable to allocate ERP request");
cqr->status = DASD_CQR_FAILED;
cqr->stopclk = get_clock ();
} else {
- DEV_MESSAGE (KERN_ERR, device,
+ DBF_DEV_EVENT(DBF_ERR, device,
"Unable to allocate ERP request "
"(%i retries left)",
cqr->retries);
break;
}
default:
- DEV_MESSAGE(KERN_DEBUG, device,
+ DBF_DEV_EVENT(DBF_WARNING, device,
"invalid subcommand modifier 0x%x "
"for Diagnostic Control Command",
sense[25]);
erp = dasd_3990_erp_compound(erp, sense);
} else {
- /* No retry left and no additional special handling */
- /*necessary */
- DEV_MESSAGE(KERN_ERR, device,
- "no retries left for erp %p - "
- "set status to FAILED", erp);
+ /*
+ * No retry left and no additional special handling
+ * necessary
+ */
+ dev_err(&device->cdev->dev,
+ "ERP %p has run out of retries and failed\n", erp);
erp->status = DASD_CQR_FAILED;
}
} else {
/* simple retry */
- DEV_MESSAGE(KERN_DEBUG, device,
+ DBF_DEV_EVENT(DBF_DEBUG, device,
"%i retries left for erp %p",
erp->retries, erp);
if (device->features & DASD_FEATURE_ERPLOG) {
/* print current erp_chain */
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "ERP chain at BEGINNING of ERP-ACTION");
+ dev_err(&device->cdev->dev,
+ "ERP chain at BEGINNING of ERP-ACTION\n");
for (temp_erp = cqr;
temp_erp != NULL; temp_erp = temp_erp->refers) {
- DEV_MESSAGE(KERN_ERR, device,
- " erp %p (%02x) refers to %p",
+ dev_err(&device->cdev->dev,
+ "ERP %p (%02x) refers to %p\n",
temp_erp, temp_erp->status,
temp_erp->refers);
}
(scsw_dstat(&cqr->irb.scsw) ==
(DEV_STAT_CHN_END | DEV_STAT_DEV_END))) {
- DEV_MESSAGE(KERN_DEBUG, device,
+ DBF_DEV_EVENT(DBF_DEBUG, device,
"ERP called for successful request %p"
" - NO ERP necessary", cqr);
if (device->features & DASD_FEATURE_ERPLOG) {
/* print current erp_chain */
- DEV_MESSAGE(KERN_ERR, device, "%s",
- "ERP chain at END of ERP-ACTION");
+ dev_err(&device->cdev->dev,
+ "ERP chain at END of ERP-ACTION\n");
for (temp_erp = erp;
temp_erp != NULL; temp_erp = temp_erp->refers) {
- DEV_MESSAGE(KERN_ERR, device,
- " erp %p (%02x) refers to %p",
+ dev_err(&device->cdev->dev,
+ "ERP %p (%02x) refers to %p\n",
temp_erp, temp_erp->status,
temp_erp->refers);
}
list_add_tail(&erp->blocklist, &cqr->blocklist);
}
+
+
return erp;
} /* end dasd_3990_erp_action */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff