#ifndef _LINUX_TI113X_H
#define _LINUX_TI113X_H
-#include <linux/config.h>
/* Register definitions for TI 113X PCI-to-CardBus bridges */
#define TI122X_SCR_SER_STEP 0xc0000000
#define TI122X_SCR_INTRTIE 0x20000000
+#define TIXX21_SCR_TIEALL 0x10000000
#define TI122X_SCR_CBRSVD 0x00400000
#define TI122X_SCR_MRBURSTDN 0x00008000
#define TI122X_SCR_MRBURSTUP 0x00004000
/* EnE test register */
#define ENE_TEST_C9 0xc9 /* 8bit */
#define ENE_TEST_C9_TLTENABLE 0x02
-
-#ifdef CONFIG_CARDBUS
+#define ENE_TEST_C9_PFENABLE_F0 0x04
+#define ENE_TEST_C9_PFENABLE_F1 0x08
+#define ENE_TEST_C9_PFENABLE (ENE_TEST_C9_PFENABLE_F0 | ENE_TEST_C9_PFENABLE_F1)
+#define ENE_TEST_C9_WPDISALBLE_F0 0x40
+#define ENE_TEST_C9_WPDISALBLE_F1 0x80
+#define ENE_TEST_C9_WPDISALBLE (ENE_TEST_C9_WPDISALBLE_F0 | ENE_TEST_C9_WPDISALBLE_F1)
/*
* Texas Instruments CardBus controller overrides.
u8 new, reg = exca_readb(socket, I365_INTCTL);
new = reg & ~I365_INTR_ENA;
- if (socket->cb_irq)
+ if (socket->dev->irq)
new |= I365_INTR_ENA;
if (new != reg)
exca_writeb(socket, I365_INTCTL, new);
return 0;
}
+static void ti113x_use_isa_irq(struct yenta_socket *socket)
+{
+ int isa_irq = -1;
+ u8 intctl;
+ u32 isa_irq_mask = 0;
+
+ if (!isa_probe)
+ return;
+
+ /* get a free isa int */
+ isa_irq_mask = yenta_probe_irq(socket, isa_interrupts);
+ if (!isa_irq_mask)
+ return; /* no useable isa irq found */
+
+ /* choose highest available */
+ for (; isa_irq_mask; isa_irq++)
+ isa_irq_mask >>= 1;
+ socket->cb_irq = isa_irq;
+
+ exca_writeb(socket, I365_CSCINT, (isa_irq << 4));
+
+ intctl = exca_readb(socket, I365_INTCTL);
+ intctl &= ~(I365_INTR_ENA | I365_IRQ_MASK); /* CSC Enable */
+ exca_writeb(socket, I365_INTCTL, intctl);
+
+ dev_info(&socket->dev->dev,
+ "Yenta TI113x: using isa irq %d for CardBus\n", isa_irq);
+}
+
+
static int ti113x_override(struct yenta_socket *socket)
{
u8 cardctl;
cardctl = config_readb(socket, TI113X_CARD_CONTROL);
cardctl &= ~(TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_IREQ | TI113X_CCR_PCI_CSC);
- if (socket->cb_irq)
+ if (socket->dev->irq)
cardctl |= TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_CSC | TI113X_CCR_PCI_IREQ;
+ else
+ ti113x_use_isa_irq(socket);
+
config_writeb(socket, TI113X_CARD_CONTROL, cardctl);
return ti_override(socket);
mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
- printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
- pci_name(socket->dev), mfunc, devctl);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: mfunc 0x%08x, devctl 0x%02x\n", mfunc, devctl);
/* make sure PCI interrupts are enabled before probing */
ti_init(socket);
* We're here which means PCI interrupts are _not_ delivered. try to
* find the right setting (all serial or parallel)
*/
- printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: probing PCI interrupt failed, trying to fix\n");
/* for serial PCI make sure MFUNC3 is set to IRQSER */
if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: all-serial interrupts ok\n");
mfunc_old = mfunc;
goto out;
}
}
/* serial PCI interrupts not working fall back to parallel */
- printk(KERN_INFO "Yenta TI: socket %s falling back to parallel PCI interrupts\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: falling back to parallel PCI interrupts\n");
devctl &= ~TI113X_DCR_IMODE_MASK;
devctl |= TI113X_DCR_IMODE_SERIAL; /* serial ISA could be right */
config_writeb(socket, TI113X_DEVICE_CONTROL, devctl);
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
mfunc_old = mfunc;
- printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: parallel PCI interrupts ok\n");
} else {
/* not working, back to old value */
mfunc = mfunc_old;
out:
if (pci_irq_status < 1) {
socket->cb_irq = 0;
- printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Yenta TI: no PCI interrupts. Fish. "
+ "Please report.\n");
}
}
mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
- printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
- pci_name(socket->dev), mfunc, devctl);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: mfunc 0x%08x, devctl 0x%02x\n",
+ mfunc, devctl);
/* if IRQs are configured as tied, align irq of func1 with func0 */
sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
* We're here which means PCI interrupts are _not_ delivered. try to
* find the right setting
*/
- printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
- pci_name(socket->dev));
-
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: probing PCI interrupt failed, trying to fix\n");
/* if all serial: set INTRTIE, probe again */
if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
if (ti12xx_tie_interrupts(socket, &old_irq)) {
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts, tied ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: all-serial interrupts, tied ok\n");
goto out;
}
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: parallel PCI interrupts ok\n");
goto out;
}
if (pci_irq_status == -1)
goto out;
}
-
+
/* still nothing: set INTRTIE */
if (ti12xx_tie_interrupts(socket, &old_irq)) {
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts, tied ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: parallel PCI interrupts, tied ok\n");
goto out;
}
out:
if (pci_irq_status < 1) {
socket->cb_irq = 0;
- printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: no PCI interrupts. Fish. Please report.\n");
}
}
int devfn;
unsigned int state;
int ret = 1;
+ u32 sysctl;
/* catch the two-slot controllers */
switch (socket->dev->device) {
*/
break;
+ case PCI_DEVICE_ID_TI_XX12:
+ case PCI_DEVICE_ID_TI_X515:
+ case PCI_DEVICE_ID_TI_X420:
+ case PCI_DEVICE_ID_TI_X620:
+ case PCI_DEVICE_ID_TI_XX21_XX11:
+ case PCI_DEVICE_ID_TI_7410:
+ case PCI_DEVICE_ID_TI_7610:
+ /*
+ * those are either single or dual slot CB with additional functions
+ * like 1394, smartcard reader, etc. check the TIEALL flag for them
+ * the TIEALL flag binds the IRQ of all functions toghether.
+ * we catch the single slot variants later.
+ */
+ sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
+ if (sysctl & TIXX21_SCR_TIEALL)
+ return 0;
+
+ break;
+
/* single-slot controllers have the 2nd slot empty always :) */
default:
return 1;
if (!func)
return 1;
+ /*
+ * check that the device id of both slots match. this is needed for the
+ * XX21 and the XX11 controller that share the same device id for single
+ * and dual slot controllers. return '2nd slot empty'. we already checked
+ * if the interrupt is tied to another function.
+ */
+ if (socket->dev->device != func->device)
+ goto out;
+
slot2 = pci_get_drvdata(func);
if (!slot2)
goto out;
/* check state */
- yenta_get_status(&socket->socket, &state);
+ yenta_get_status(&slot2->socket, &state);
if (state & SS_DETECT) {
ret = 0;
goto out;
/* make sure that memory burst is active */
val_orig = val = config_readl(socket, TI113X_SYSTEM_CONTROL);
if (disable_clkrun && PCI_FUNC(socket->dev->devfn) == 0) {
- printk(KERN_INFO "Yenta: Disabling CLKRUN feature\n");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Disabling CLKRUN feature\n");
val |= TI113X_SCR_KEEPCLK;
}
if (!(val & TI122X_SCR_MRBURSTUP)) {
- printk(KERN_INFO "Yenta: Enabling burst memory read transactions\n");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Enabling burst memory read transactions\n");
val |= TI122X_SCR_MRBURSTUP;
}
if (val_orig != val)
config_writel(socket, TI113X_SYSTEM_CONTROL, val);
/*
- * for EnE bridges only: clear testbit TLTEnable. this makes the
- * RME Hammerfall DSP sound card working.
- */
- if (socket->dev->vendor == PCI_VENDOR_ID_ENE) {
- u8 test_c9 = config_readb(socket, ENE_TEST_C9);
- test_c9 &= ~ENE_TEST_C9_TLTENABLE;
- config_writeb(socket, ENE_TEST_C9, test_c9);
- }
-
- /*
* Yenta expects controllers to use CSCINT to route
* CSC interrupts to PCI rather than INTVAL.
*/
val = config_readb(socket, TI1250_DIAGNOSTIC);
- printk(KERN_INFO "Yenta: Using %s to route CSC interrupts to PCI\n",
- (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
- printk(KERN_INFO "Yenta: Routing CardBus interrupts to %s\n",
- (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Using %s to route CSC interrupts to PCI\n",
+ (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Routing CardBus interrupts to %s\n",
+ (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
/* do irqrouting, depending on function */
if (PCI_FUNC(socket->dev->devfn) == 0)
diag |= TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ;
if (diag != old) {
- printk(KERN_INFO "Yenta: adjusting diagnostic: %02x -> %02x\n",
- old, diag);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "adjusting diagnostic: %02x -> %02x\n",
+ old, diag);
config_writeb(socket, TI1250_DIAGNOSTIC, diag);
}
return ti12xx_override(socket);
}
-#endif /* CONFIG_CARDBUS */
+
+/**
+ * EnE specific part. EnE bridges are register compatible with TI bridges but
+ * have their own test registers and more important their own little problems.
+ * Some fixup code to make everybody happy (TM).
+ */
+
+#ifdef CONFIG_YENTA_ENE_TUNE
+/*
+ * set/clear various test bits:
+ * Defaults to clear the bit.
+ * - mask (u8) defines what bits to change
+ * - bits (u8) is the values to change them to
+ * -> it's
+ * current = (current & ~mask) | bits
+ */
+/* pci ids of devices that wants to have the bit set */
+#define DEVID(_vend,_dev,_subvend,_subdev,mask,bits) { \
+ .vendor = _vend, \
+ .device = _dev, \
+ .subvendor = _subvend, \
+ .subdevice = _subdev, \
+ .driver_data = ((mask) << 8 | (bits)), \
+ }
+static struct pci_device_id ene_tune_tbl[] = {
+ /* Echo Audio products based on motorola DSP56301 and DSP56361 */
+ DEVID(PCI_VENDOR_ID_MOTOROLA, 0x1801, 0xECC0, PCI_ANY_ID,
+ ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
+ DEVID(PCI_VENDOR_ID_MOTOROLA, 0x3410, 0xECC0, PCI_ANY_ID,
+ ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
+
+ {}
+};
+
+static void ene_tune_bridge(struct pcmcia_socket *sock, struct pci_bus *bus)
+{
+ struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
+ struct pci_dev *dev;
+ struct pci_device_id *id = NULL;
+ u8 test_c9, old_c9, mask, bits;
+
+ list_for_each_entry(dev, &bus->devices, bus_list) {
+ id = (struct pci_device_id *) pci_match_id(ene_tune_tbl, dev);
+ if (id)
+ break;
+ }
+
+ test_c9 = old_c9 = config_readb(socket, ENE_TEST_C9);
+ if (id) {
+ mask = (id->driver_data >> 8) & 0xFF;
+ bits = id->driver_data & 0xFF;
+
+ test_c9 = (test_c9 & ~mask) | bits;
+ }
+ else
+ /* default to clear TLTEnable bit, old behaviour */
+ test_c9 &= ~ENE_TEST_C9_TLTENABLE;
+
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "EnE: chaning testregister 0xC9, %02x -> %02x\n",
+ old_c9, test_c9);
+ config_writeb(socket, ENE_TEST_C9, test_c9);
+}
+
+static int ene_override(struct yenta_socket *socket)
+{
+ /* install tune_bridge() function */
+ socket->socket.tune_bridge = ene_tune_bridge;
+
+ return ti1250_override(socket);
+}
+#else
+# define ene_override ti1250_override
+#endif /* !CONFIG_YENTA_ENE_TUNE */
#endif /* _LINUX_TI113X_H */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff