#ifndef _LINUX_TI113X_H
#define _LINUX_TI113X_H
-#include <linux/config.h>
/* Register definitions for TI 113X PCI-to-CardBus bridges */
#define ENE_TEST_C9_TLTENABLE 0x02
#define ENE_TEST_C9_PFENABLE_F0 0x04
#define ENE_TEST_C9_PFENABLE_F1 0x08
-#define ENE_TEST_C9_PFENABLE (ENE_TEST_C9_PFENABLE_F0 | ENE_TEST_C9_PFENABLE_F0)
+#define ENE_TEST_C9_PFENABLE (ENE_TEST_C9_PFENABLE_F0 | ENE_TEST_C9_PFENABLE_F1)
#define ENE_TEST_C9_WPDISALBLE_F0 0x40
#define ENE_TEST_C9_WPDISALBLE_F1 0x80
#define ENE_TEST_C9_WPDISALBLE (ENE_TEST_C9_WPDISALBLE_F0 | ENE_TEST_C9_WPDISALBLE_F1)
u8 new, reg = exca_readb(socket, I365_INTCTL);
new = reg & ~I365_INTR_ENA;
- if (socket->cb_irq)
+ if (socket->dev->irq)
new |= I365_INTR_ENA;
if (new != reg)
exca_writeb(socket, I365_INTCTL, new);
return 0;
}
+static void ti113x_use_isa_irq(struct yenta_socket *socket)
+{
+ int isa_irq = -1;
+ u8 intctl;
+ u32 isa_irq_mask = 0;
+
+ if (!isa_probe)
+ return;
+
+ /* get a free isa int */
+ isa_irq_mask = yenta_probe_irq(socket, isa_interrupts);
+ if (!isa_irq_mask)
+ return; /* no useable isa irq found */
+
+ /* choose highest available */
+ for (; isa_irq_mask; isa_irq++)
+ isa_irq_mask >>= 1;
+ socket->cb_irq = isa_irq;
+
+ exca_writeb(socket, I365_CSCINT, (isa_irq << 4));
+
+ intctl = exca_readb(socket, I365_INTCTL);
+ intctl &= ~(I365_INTR_ENA | I365_IRQ_MASK); /* CSC Enable */
+ exca_writeb(socket, I365_INTCTL, intctl);
+
+ dev_info(&socket->dev->dev,
+ "Yenta TI113x: using isa irq %d for CardBus\n", isa_irq);
+}
+
+
static int ti113x_override(struct yenta_socket *socket)
{
u8 cardctl;
cardctl = config_readb(socket, TI113X_CARD_CONTROL);
cardctl &= ~(TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_IREQ | TI113X_CCR_PCI_CSC);
- if (socket->cb_irq)
+ if (socket->dev->irq)
cardctl |= TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_CSC | TI113X_CCR_PCI_IREQ;
+ else
+ ti113x_use_isa_irq(socket);
+
config_writeb(socket, TI113X_CARD_CONTROL, cardctl);
return ti_override(socket);
mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
- printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
- pci_name(socket->dev), mfunc, devctl);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: mfunc 0x%08x, devctl 0x%02x\n", mfunc, devctl);
/* make sure PCI interrupts are enabled before probing */
ti_init(socket);
* We're here which means PCI interrupts are _not_ delivered. try to
* find the right setting (all serial or parallel)
*/
- printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: probing PCI interrupt failed, trying to fix\n");
/* for serial PCI make sure MFUNC3 is set to IRQSER */
if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: all-serial interrupts ok\n");
mfunc_old = mfunc;
goto out;
}
}
/* serial PCI interrupts not working fall back to parallel */
- printk(KERN_INFO "Yenta TI: socket %s falling back to parallel PCI interrupts\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: falling back to parallel PCI interrupts\n");
devctl &= ~TI113X_DCR_IMODE_MASK;
devctl |= TI113X_DCR_IMODE_SERIAL; /* serial ISA could be right */
config_writeb(socket, TI113X_DEVICE_CONTROL, devctl);
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
mfunc_old = mfunc;
- printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: parallel PCI interrupts ok\n");
} else {
/* not working, back to old value */
mfunc = mfunc_old;
out:
if (pci_irq_status < 1) {
socket->cb_irq = 0;
- printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Yenta TI: no PCI interrupts. Fish. "
+ "Please report.\n");
}
}
mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
- printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
- pci_name(socket->dev), mfunc, devctl);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: mfunc 0x%08x, devctl 0x%02x\n",
+ mfunc, devctl);
/* if IRQs are configured as tied, align irq of func1 with func0 */
sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
* We're here which means PCI interrupts are _not_ delivered. try to
* find the right setting
*/
- printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
- pci_name(socket->dev));
-
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: probing PCI interrupt failed, trying to fix\n");
/* if all serial: set INTRTIE, probe again */
if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
if (ti12xx_tie_interrupts(socket, &old_irq)) {
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts, tied ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: all-serial interrupts, tied ok\n");
goto out;
}
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: parallel PCI interrupts ok\n");
goto out;
}
if (pci_irq_status == -1)
goto out;
}
-
+
/* still nothing: set INTRTIE */
if (ti12xx_tie_interrupts(socket, &old_irq)) {
pci_irq_status = yenta_probe_cb_irq(socket);
if (pci_irq_status == 1) {
- printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts, tied ok\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: parallel PCI interrupts, tied ok\n");
goto out;
}
out:
if (pci_irq_status < 1) {
socket->cb_irq = 0;
- printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
- pci_name(socket->dev));
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "TI: no PCI interrupts. Fish. Please report.\n");
}
}
*/
break;
+ case PCI_DEVICE_ID_TI_XX12:
case PCI_DEVICE_ID_TI_X515:
case PCI_DEVICE_ID_TI_X420:
case PCI_DEVICE_ID_TI_X620:
goto out;
/* check state */
- yenta_get_status(&socket->socket, &state);
+ yenta_get_status(&slot2->socket, &state);
if (state & SS_DETECT) {
ret = 0;
goto out;
/* make sure that memory burst is active */
val_orig = val = config_readl(socket, TI113X_SYSTEM_CONTROL);
if (disable_clkrun && PCI_FUNC(socket->dev->devfn) == 0) {
- printk(KERN_INFO "Yenta: Disabling CLKRUN feature\n");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Disabling CLKRUN feature\n");
val |= TI113X_SCR_KEEPCLK;
}
if (!(val & TI122X_SCR_MRBURSTUP)) {
- printk(KERN_INFO "Yenta: Enabling burst memory read transactions\n");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Enabling burst memory read transactions\n");
val |= TI122X_SCR_MRBURSTUP;
}
if (val_orig != val)
* CSC interrupts to PCI rather than INTVAL.
*/
val = config_readb(socket, TI1250_DIAGNOSTIC);
- printk(KERN_INFO "Yenta: Using %s to route CSC interrupts to PCI\n",
- (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
- printk(KERN_INFO "Yenta: Routing CardBus interrupts to %s\n",
- (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Using %s to route CSC interrupts to PCI\n",
+ (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "Routing CardBus interrupts to %s\n",
+ (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
/* do irqrouting, depending on function */
if (PCI_FUNC(socket->dev->devfn) == 0)
diag |= TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ;
if (diag != old) {
- printk(KERN_INFO "Yenta: adjusting diagnostic: %02x -> %02x\n",
- old, diag);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "adjusting diagnostic: %02x -> %02x\n",
+ old, diag);
config_writeb(socket, TI1250_DIAGNOSTIC, diag);
}
* Some fixup code to make everybody happy (TM).
*/
-#ifdef CONFIG_CARDBUS
-/**
+#ifdef CONFIG_YENTA_ENE_TUNE
+/*
* set/clear various test bits:
* Defaults to clear the bit.
* - mask (u8) defines what bits to change
/* default to clear TLTEnable bit, old behaviour */
test_c9 &= ~ENE_TEST_C9_TLTENABLE;
- printk(KERN_INFO "yenta EnE: chaning testregister 0xC9, %02x -> %02x\n", old_c9, test_c9);
+ dev_printk(KERN_INFO, &socket->dev->dev,
+ "EnE: chaning testregister 0xC9, %02x -> %02x\n",
+ old_c9, test_c9);
config_writeb(socket, ENE_TEST_C9, test_c9);
}
}
#else
# define ene_override ti1250_override
-#endif
+#endif /* !CONFIG_YENTA_ENE_TUNE */
#endif /* _LINUX_TI113X_H */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff