* Write to card's Host Adapter Command Register. Include a delay for
* those times when it is needed.
*/
-static inline void
+static void
hacr_write_slow(u_long base,
u_char hacr)
{
/*
* Write 1 byte to the MMC.
*/
-static inline void
+static void
mmc_out(u_long base,
u_short o,
u_char d)
* Routine to write bytes to the Modem Management Controller.
* We start by the end because it is the way it should be !
*/
-static inline void
+static void
mmc_write(u_long base,
u_char o,
u_char * b,
* Read 1 byte from the MMC.
* Optimised version for 1 byte, avoid using memory...
*/
-static inline u_char
+static u_char
mmc_in(u_long base,
u_short o)
{
* (code has just been moved in the above function)
* We start by the end because it is the way it should be !
*/
-static inline void
+static void
mmc_read(u_long base,
u_char o,
u_char * b,
/*------------------------------------------------------------------*/
/*
* Wait for the frequency EEprom to complete a command...
- * I hope this one will be optimally inlined...
*/
-static inline void
+static void
fee_wait(u_long base, /* i/o port of the card */
int delay, /* Base delay to wait for */
int number) /* Number of time to wait */
}
/* Called when a WavePoint beacon is received */
-static inline void wl_roam_gather(struct net_device * dev,
- u_char * hdr, /* Beacon header */
- u_char * stats) /* SNR, Signal quality
+static void wl_roam_gather(struct net_device * dev,
+ u_char * hdr, /* Beacon header */
+ u_char * stats) /* SNR, Signal quality
of packet */
{
wavepoint_beacon *beacon= (wavepoint_beacon *)hdr; /* Rcvd. Beacon */
static inline int WAVELAN_BEACON(unsigned char *data)
{
wavepoint_beacon *beacon= (wavepoint_beacon *)data;
- static wavepoint_beacon beacon_template={0xaa,0xaa,0x03,0x08,0x00,0x0e,0x20,0x03,0x00};
+ static const wavepoint_beacon beacon_template={0xaa,0xaa,0x03,0x08,0x00,0x0e,0x20,0x03,0x00};
if(memcmp(beacon,&beacon_template,9)==0)
return 1;
}
while(((status & SR3_EXEC_STATE_MASK) != SR3_EXEC_IDLE) && (spin-- > 0));
- /* If the interrupt hasn't be posted */
- if(spin <= 0)
- {
+ /* If the interrupt hasn't been posted */
+ if (spin < 0) {
#ifdef DEBUG_INTERRUPT_ERROR
printk(KERN_INFO "wv_82593_cmd: %s timeout (previous command), status 0x%02x\n",
str, status);
* wavelan_interrupt is not an option...), so you may experience
* some delay sometime...
*/
-static inline void
+static void
wv_82593_reconfig(struct net_device * dev)
{
net_local * lp = netdev_priv(dev);
static void
wv_psa_show(psa_t * p)
{
- DECLARE_MAC_BUF(mac);
printk(KERN_DEBUG "##### wavelan psa contents: #####\n");
printk(KERN_DEBUG "psa_io_base_addr_1: 0x%02X %02X %02X %02X\n",
p->psa_io_base_addr_1,
printk(KERN_DEBUG "psa_holi_params: 0x%02x, ", p->psa_holi_params);
printk("psa_int_req_no: %d\n", p->psa_int_req_no);
#ifdef DEBUG_SHOW_UNUSED
- printk(KERN_DEBUG "psa_unused0[]: %s\n",
- print_mac(mac, p->psa_unused0));
+ printk(KERN_DEBUG "psa_unused0[]: %pM\n", p->psa_unused0);
#endif /* DEBUG_SHOW_UNUSED */
- printk(KERN_DEBUG "psa_univ_mac_addr[]: %s\n",
- print_mac(mac, p->psa_univ_mac_addr));
- printk(KERN_DEBUG "psa_local_mac_addr[]: %s\n",
- print_mac(mac, p->psa_local_mac_addr));
+ printk(KERN_DEBUG "psa_univ_mac_addr[]: %pM\n", p->psa_univ_mac_addr);
+ printk(KERN_DEBUG "psa_local_mac_addr[]: %pM\n", p->psa_local_mac_addr);
printk(KERN_DEBUG "psa_univ_local_sel: %d, ", p->psa_univ_local_sel);
printk("psa_comp_number: %d, ", p->psa_comp_number);
printk("psa_thr_pre_set: 0x%02x\n", p->psa_thr_pre_set);
p->psa_call_code[6],
p->psa_call_code[7]);
#ifdef DEBUG_SHOW_UNUSED
- printk(KERN_DEBUG "psa_reserved[]: %02X:%02X:%02X:%02X\n",
+ printk(KERN_DEBUG "psa_reserved[]: %02X:%02X\n",
p->psa_reserved[0],
- p->psa_reserved[1],
- p->psa_reserved[2],
- p->psa_reserved[3]);
+ p->psa_reserved[1]);
#endif /* DEBUG_SHOW_UNUSED */
printk(KERN_DEBUG "psa_conf_status: %d, ", p->psa_conf_status);
printk("psa_crc: 0x%02x%02x, ", p->psa_crc[0], p->psa_crc[1]);
/*
* Dump packet header (and content if necessary) on the screen
*/
-static inline void
+static void
wv_packet_info(u_char * p, /* Packet to dump */
int length, /* Length of the packet */
char * msg1, /* Name of the device */
{
int i;
int maxi;
- DECLARE_MAC_BUF(mac);
- printk(KERN_DEBUG "%s: %s(): dest %s, length %d\n",
- msg1, msg2, print_mac(mac, p), length);
- printk(KERN_DEBUG "%s: %s(): src %s, type 0x%02X%02X\n",
- msg1, msg2, print_mac(mac, &p[6]), p[12], p[13]);
+ printk(KERN_DEBUG "%s: %s(): dest %pM, length %d\n",
+ msg1, msg2, p, length);
+ printk(KERN_DEBUG "%s: %s(): src %pM, type 0x%02X%02X\n",
+ msg1, msg2, &p[6], p[12], p[13]);
#ifdef DEBUG_PACKET_DUMP
* This is the information which is displayed by the driver at startup
* There is a lot of flag to configure it at your will...
*/
-static inline void
+static void
wv_init_info(struct net_device * dev)
{
unsigned int base = dev->base_addr;
psa_t psa;
- DECLARE_MAC_BUF(mac);
/* Read the parameter storage area */
psa_read(dev, 0, (unsigned char *) &psa, sizeof(psa));
#ifdef DEBUG_BASIC_SHOW
/* Now, let's go for the basic stuff */
- printk(KERN_NOTICE "%s: WaveLAN: port %#x, irq %d, "
- "hw_addr %s",
- dev->name, base, dev->irq,
- print_mac(mac, dev->dev_addr));
+ printk(KERN_NOTICE "%s: WaveLAN: port %#x, irq %d, hw_addr %pM",
+ dev->name, base, dev->irq, dev->dev_addr);
/* Print current network id */
if(psa.psa_nwid_select)
lp->mc_count = 0;
wv_82593_reconfig(dev);
-
- /* Tell the kernel that we are doing a really bad job... */
- dev->flags |= IFF_PROMISC;
}
}
else
lp->mc_count = 0;
wv_82593_reconfig(dev);
-
- /* Tell the kernel that we are doing a really bad job... */
- dev->flags |= IFF_ALLMULTI;
}
}
else
* Frequency setting (for hardware able of it)
* It's a bit complicated and you don't really want to look into it...
*/
-static inline int
+static int
wv_set_frequency(u_long base, /* i/o port of the card */
iw_freq * frequency)
{
/*
* Give the list of available frequencies
*/
-static inline int
+static int
wv_frequency_list(u_long base, /* i/o port of the card */
iw_freq * list, /* List of frequency to fill */
int max) /* Maximum number of frequencies */
char *extra)
{
#ifdef DEBUG_IOCTL_INFO
- printk(KERN_DEBUG "Set AP to : %02X:%02X:%02X:%02X:%02X:%02X\n",
- wrqu->ap_addr.sa_data[0],
- wrqu->ap_addr.sa_data[1],
- wrqu->ap_addr.sa_data[2],
- wrqu->ap_addr.sa_data[3],
- wrqu->ap_addr.sa_data[4],
- wrqu->ap_addr.sa_data[5]);
+ printk(KERN_DEBUG "Set AP to : %pM\n", wrqu->ap_addr.sa_data);
#endif /* DEBUG_IOCTL_INFO */
return -EOPNOTSUPP;
* frame pointer and verify that the frame seem correct
* (called by wv_packet_rcv())
*/
-static inline int
+static int
wv_start_of_frame(struct net_device * dev,
int rfp, /* end of frame */
int wrap) /* start of buffer */
* Note: if any errors occur, the packet is "dropped on the floor"
* (called by wv_packet_rcv())
*/
-static inline void
+static void
wv_packet_read(struct net_device * dev,
int fd_p,
int sksize)
netif_rx(skb);
/* Keep stats up to date */
- dev->last_rx = jiffies;
lp->stats.rx_packets++;
lp->stats.rx_bytes += sksize;
* (called by wavelan_interrupt())
* Note : the spinlock is already grabbed for us and irq are disabled.
*/
-static inline void
+static void
wv_packet_rcv(struct net_device * dev)
{
unsigned int base = dev->base_addr;
* the transmit.
* (called in wavelan_packet_xmit())
*/
-static inline void
+static void
wv_packet_write(struct net_device * dev,
void * buf,
short length)
* Routine to initialize the Modem Management Controller.
* (called by wv_hw_config())
*/
-static inline int
+static int
wv_mmc_init(struct net_device * dev)
{
unsigned int base = dev->base_addr;
int addrs_len = WAVELAN_ADDR_SIZE * lp->mc_count;
#ifdef DEBUG_CONFIG_INFO
- DECLARE_MAC_BUF(mac);
printk(KERN_DEBUG "%s: wv_hw_config(): set %d multicast addresses:\n",
dev->name, lp->mc_count);
for(dmi=dev->mc_list; dmi; dmi=dmi->next)
- printk(KERN_DEBUG " %s\n",
- print_mac(mac, dmi->dmi_addr));
+ printk(KERN_DEBUG " %pM\n", dmi->dmi_addr);
#endif
/* Initialize adapter's ethernet multicast addresses */
* wavelan.
* (called by wv_config())
*/
-static inline int
+static int
wv_pcmcia_reset(struct net_device * dev)
{
int i;
#endif
i = pcmcia_access_configuration_register(link, ®);
- if(i != CS_SUCCESS)
+ if (i != 0)
{
cs_error(link, AccessConfigurationRegister, i);
return FALSE;
reg.Action = CS_WRITE;
reg.Value = reg.Value | COR_SW_RESET;
i = pcmcia_access_configuration_register(link, ®);
- if(i != CS_SUCCESS)
+ if (i != 0)
{
cs_error(link, AccessConfigurationRegister, i);
return FALSE;
reg.Action = CS_WRITE;
reg.Value = COR_LEVEL_IRQ | COR_CONFIG;
i = pcmcia_access_configuration_register(link, ®);
- if(i != CS_SUCCESS)
+ if (i != 0)
{
cs_error(link, AccessConfigurationRegister, i);
return FALSE;
* 2. Start the LAN controller's receive unit
* (called by wavelan_event(), wavelan_watchdog() and wavelan_open())
*/
-static inline void
+static void
wv_hw_reset(struct net_device * dev)
{
net_local * lp = netdev_priv(dev);
* device available to the system.
* (called by wavelan_event())
*/
-static inline int
+static int
wv_pcmcia_config(struct pcmcia_device * link)
{
struct net_device * dev = (struct net_device *) link->priv;
do
{
i = pcmcia_request_io(link, &link->io);
- if(i != CS_SUCCESS)
+ if (i != 0)
{
cs_error(link, RequestIO, i);
break;
* actually assign a handler to the interrupt.
*/
i = pcmcia_request_irq(link, &link->irq);
- if(i != CS_SUCCESS)
+ if (i != 0)
{
cs_error(link, RequestIRQ, i);
break;
*/
link->conf.ConfigIndex = 1;
i = pcmcia_request_configuration(link, &link->conf);
- if(i != CS_SUCCESS)
+ if (i != 0)
{
cs_error(link, RequestConfiguration, i);
break;
req.Base = req.Size = 0;
req.AccessSpeed = mem_speed;
i = pcmcia_request_window(&link, &req, &link->win);
- if(i != CS_SUCCESS)
+ if (i != 0)
{
cs_error(link, RequestWindow, i);
break;
mem.CardOffset = 0; mem.Page = 0;
i = pcmcia_map_mem_page(link->win, &mem);
- if(i != CS_SUCCESS)
+ if (i != 0)
{
cs_error(link, MapMemPage, i);
break;
p_dev->io.IOAddrLines = 3;
/* Interrupt setup */
- p_dev->irq.Attributes = IRQ_TYPE_EXCLUSIVE | IRQ_HANDLE_PRESENT;
+ p_dev->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING | IRQ_HANDLE_PRESENT;
p_dev->irq.IRQInfo1 = IRQ_LEVEL_ID;
p_dev->irq.Handler = wavelan_interrupt;