#include "rt61pci.h"
/*
+ * Allow hardware encryption to be disabled.
+ */
+static int modparam_nohwcrypt = 0;
+module_param_named(nohwcrypt, modparam_nohwcrypt, bool, S_IRUGO);
+MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption.");
+
+/*
* Register access.
* BBP and RF register require indirect register access,
* and use the CSR registers PHY_CSR3 and PHY_CSR4 to achieve this.
rt2x00_rf_write(rt2x00dev, word, value);
}
-#ifdef CONFIG_RT61PCI_LEDS
+#ifdef CONFIG_RT2X00_LIB_LEDS
/*
* This function is only called from rt61pci_led_brightness()
* make gcc happy by placing this function inside the
rt2x00_set_field32(®, HOST_CMD_CSR_INTERRUPT_MCU, 1);
rt2x00pci_register_write(rt2x00dev, HOST_CMD_CSR, reg);
}
-#endif /* CONFIG_RT61PCI_LEDS */
+#endif /* CONFIG_RT2X00_LIB_LEDS */
static void rt61pci_eepromregister_read(struct eeprom_93cx6 *eeprom)
{
};
#endif /* CONFIG_RT2X00_LIB_DEBUGFS */
-#ifdef CONFIG_RT61PCI_RFKILL
+#ifdef CONFIG_RT2X00_LIB_RFKILL
static int rt61pci_rfkill_poll(struct rt2x00_dev *rt2x00dev)
{
u32 reg;
}
#else
#define rt61pci_rfkill_poll NULL
-#endif /* CONFIG_RT61PCI_RFKILL */
+#endif /* CONFIG_RT2X00_LIB_RFKILL */
-#ifdef CONFIG_RT61PCI_LEDS
+#ifdef CONFIG_RT2X00_LIB_LEDS
static void rt61pci_brightness_set(struct led_classdev *led_cdev,
enum led_brightness brightness)
{
return 0;
}
-#endif /* CONFIG_RT61PCI_LEDS */
+
+static void rt61pci_init_led(struct rt2x00_dev *rt2x00dev,
+ struct rt2x00_led *led,
+ enum led_type type)
+{
+ led->rt2x00dev = rt2x00dev;
+ led->type = type;
+ led->led_dev.brightness_set = rt61pci_brightness_set;
+ led->led_dev.blink_set = rt61pci_blink_set;
+ led->flags = LED_INITIALIZED;
+}
+#endif /* CONFIG_RT2X00_LIB_LEDS */
/*
* Configuration handlers.
*/
+static int rt61pci_config_shared_key(struct rt2x00_dev *rt2x00dev,
+ struct rt2x00lib_crypto *crypto,
+ struct ieee80211_key_conf *key)
+{
+ struct hw_key_entry key_entry;
+ struct rt2x00_field32 field;
+ u32 mask;
+ u32 reg;
+
+ if (crypto->cmd == SET_KEY) {
+ /*
+ * rt2x00lib can't determine the correct free
+ * key_idx for shared keys. We have 1 register
+ * with key valid bits. The goal is simple, read
+ * the register, if that is full we have no slots
+ * left.
+ * Note that each BSS is allowed to have up to 4
+ * shared keys, so put a mask over the allowed
+ * entries.
+ */
+ mask = (0xf << crypto->bssidx);
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR0, ®);
+ reg &= mask;
+
+ if (reg && reg == mask)
+ return -ENOSPC;
+
+ key->hw_key_idx += reg ? ffz(reg) : 0;
+
+ /*
+ * Upload key to hardware
+ */
+ memcpy(key_entry.key, crypto->key,
+ sizeof(key_entry.key));
+ memcpy(key_entry.tx_mic, crypto->tx_mic,
+ sizeof(key_entry.tx_mic));
+ memcpy(key_entry.rx_mic, crypto->rx_mic,
+ sizeof(key_entry.rx_mic));
+
+ reg = SHARED_KEY_ENTRY(key->hw_key_idx);
+ rt2x00pci_register_multiwrite(rt2x00dev, reg,
+ &key_entry, sizeof(key_entry));
+
+ /*
+ * The cipher types are stored over 2 registers.
+ * bssidx 0 and 1 keys are stored in SEC_CSR1 and
+ * bssidx 1 and 2 keys are stored in SEC_CSR5.
+ * Using the correct defines correctly will cause overhead,
+ * so just calculate the correct offset.
+ */
+ if (key->hw_key_idx < 8) {
+ field.bit_offset = (3 * key->hw_key_idx);
+ field.bit_mask = 0x7 << field.bit_offset;
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR1, ®);
+ rt2x00_set_field32(®, field, crypto->cipher);
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR1, reg);
+ } else {
+ field.bit_offset = (3 * (key->hw_key_idx - 8));
+ field.bit_mask = 0x7 << field.bit_offset;
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR5, ®);
+ rt2x00_set_field32(®, field, crypto->cipher);
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR5, reg);
+ }
+
+ /*
+ * The driver does not support the IV/EIV generation
+ * in hardware. However it doesn't support the IV/EIV
+ * inside the ieee80211 frame either, but requires it
+ * to be provided seperately for the descriptor.
+ * rt2x00lib will cut the IV/EIV data out of all frames
+ * given to us by mac80211, but we must tell mac80211
+ * to generate the IV/EIV data.
+ */
+ key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
+ }
+
+ /*
+ * SEC_CSR0 contains only single-bit fields to indicate
+ * a particular key is valid. Because using the FIELD32()
+ * defines directly will cause a lot of overhead we use
+ * a calculation to determine the correct bit directly.
+ */
+ mask = 1 << key->hw_key_idx;
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR0, ®);
+ if (crypto->cmd == SET_KEY)
+ reg |= mask;
+ else if (crypto->cmd == DISABLE_KEY)
+ reg &= ~mask;
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR0, reg);
+
+ return 0;
+}
+
+static int rt61pci_config_pairwise_key(struct rt2x00_dev *rt2x00dev,
+ struct rt2x00lib_crypto *crypto,
+ struct ieee80211_key_conf *key)
+{
+ struct hw_pairwise_ta_entry addr_entry;
+ struct hw_key_entry key_entry;
+ u32 mask;
+ u32 reg;
+
+ if (crypto->cmd == SET_KEY) {
+ /*
+ * rt2x00lib can't determine the correct free
+ * key_idx for pairwise keys. We have 2 registers
+ * with key valid bits. The goal is simple, read
+ * the first register, if that is full move to
+ * the next register.
+ * When both registers are full, we drop the key,
+ * otherwise we use the first invalid entry.
+ */
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR2, ®);
+ if (reg && reg == ~0) {
+ key->hw_key_idx = 32;
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR3, ®);
+ if (reg && reg == ~0)
+ return -ENOSPC;
+ }
+
+ key->hw_key_idx += reg ? ffz(reg) : 0;
+
+ /*
+ * Upload key to hardware
+ */
+ memcpy(key_entry.key, crypto->key,
+ sizeof(key_entry.key));
+ memcpy(key_entry.tx_mic, crypto->tx_mic,
+ sizeof(key_entry.tx_mic));
+ memcpy(key_entry.rx_mic, crypto->rx_mic,
+ sizeof(key_entry.rx_mic));
+
+ memset(&addr_entry, 0, sizeof(addr_entry));
+ memcpy(&addr_entry, crypto->address, ETH_ALEN);
+ addr_entry.cipher = crypto->cipher;
+
+ reg = PAIRWISE_KEY_ENTRY(key->hw_key_idx);
+ rt2x00pci_register_multiwrite(rt2x00dev, reg,
+ &key_entry, sizeof(key_entry));
+
+ reg = PAIRWISE_TA_ENTRY(key->hw_key_idx);
+ rt2x00pci_register_multiwrite(rt2x00dev, reg,
+ &addr_entry, sizeof(addr_entry));
+
+ /*
+ * Enable pairwise lookup table for given BSS idx,
+ * without this received frames will not be decrypted
+ * by the hardware.
+ */
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR4, ®);
+ reg |= (1 << crypto->bssidx);
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR4, reg);
+
+ /*
+ * The driver does not support the IV/EIV generation
+ * in hardware. However it doesn't support the IV/EIV
+ * inside the ieee80211 frame either, but requires it
+ * to be provided seperately for the descriptor.
+ * rt2x00lib will cut the IV/EIV data out of all frames
+ * given to us by mac80211, but we must tell mac80211
+ * to generate the IV/EIV data.
+ */
+ key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
+ }
+
+ /*
+ * SEC_CSR2 and SEC_CSR3 contain only single-bit fields to indicate
+ * a particular key is valid. Because using the FIELD32()
+ * defines directly will cause a lot of overhead we use
+ * a calculation to determine the correct bit directly.
+ */
+ if (key->hw_key_idx < 32) {
+ mask = 1 << key->hw_key_idx;
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR2, ®);
+ if (crypto->cmd == SET_KEY)
+ reg |= mask;
+ else if (crypto->cmd == DISABLE_KEY)
+ reg &= ~mask;
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR2, reg);
+ } else {
+ mask = 1 << (key->hw_key_idx - 32);
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR3, ®);
+ if (crypto->cmd == SET_KEY)
+ reg |= mask;
+ else if (crypto->cmd == DISABLE_KEY)
+ reg &= ~mask;
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR3, reg);
+ }
+
+ return 0;
+}
+
static void rt61pci_config_filter(struct rt2x00_dev *rt2x00dev,
const unsigned int filter_flags)
{
rt2x00pci_register_write(rt2x00dev, TXRX_CSR4, reg);
}
+
+static void rt61pci_config_lna_gain(struct rt2x00_dev *rt2x00dev,
+ struct rt2x00lib_conf *libconf)
+{
+ u16 eeprom;
+ short lna_gain = 0;
+
+ if (libconf->band == IEEE80211_BAND_2GHZ) {
+ if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags))
+ lna_gain += 14;
+
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_BG, &eeprom);
+ lna_gain -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_BG_1);
+ } else {
+ if (test_bit(CONFIG_EXTERNAL_LNA_A, &rt2x00dev->flags))
+ lna_gain += 14;
+
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_A, &eeprom);
+ lna_gain -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_A_1);
+ }
+
+ rt2x00dev->lna_gain = lna_gain;
+}
+
static void rt61pci_config_phymode(struct rt2x00_dev *rt2x00dev,
const int basic_rate_mask)
{
struct rt2x00lib_conf *libconf,
const unsigned int flags)
{
+ /* Always recalculate LNA gain before changing configuration */
+ rt61pci_config_lna_gain(rt2x00dev, libconf);
+
if (flags & CONFIG_UPDATE_PHYMODE)
rt61pci_config_phymode(rt2x00dev, libconf->basic_rates);
if (flags & CONFIG_UPDATE_CHANNEL)
return fw_name;
}
-static u16 rt61pci_get_firmware_crc(void *data, const size_t len)
+static u16 rt61pci_get_firmware_crc(const void *data, const size_t len)
{
u16 crc;
return crc;
}
-static int rt61pci_load_firmware(struct rt2x00_dev *rt2x00dev, void *data,
+static int rt61pci_load_firmware(struct rt2x00_dev *rt2x00dev, const void *data,
const size_t len)
{
int i;
}
/*
+ * Hardware needs another millisecond before it is ready.
+ */
+ msleep(1);
+
+ /*
* Reset MAC and BBP registers.
*/
reg = 0;
static void rt61pci_init_rxentry(struct rt2x00_dev *rt2x00dev,
struct queue_entry *entry)
{
- struct queue_entry_priv_pci_rx *priv_rx = entry->priv_data;
+ struct queue_entry_priv_pci *entry_priv = entry->priv_data;
+ struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
u32 word;
- rt2x00_desc_read(priv_rx->desc, 5, &word);
+ rt2x00_desc_read(entry_priv->desc, 5, &word);
rt2x00_set_field32(&word, RXD_W5_BUFFER_PHYSICAL_ADDRESS,
- priv_rx->data_dma);
- rt2x00_desc_write(priv_rx->desc, 5, word);
+ skbdesc->skb_dma);
+ rt2x00_desc_write(entry_priv->desc, 5, word);
- rt2x00_desc_read(priv_rx->desc, 0, &word);
+ rt2x00_desc_read(entry_priv->desc, 0, &word);
rt2x00_set_field32(&word, RXD_W0_OWNER_NIC, 1);
- rt2x00_desc_write(priv_rx->desc, 0, word);
+ rt2x00_desc_write(entry_priv->desc, 0, word);
}
static void rt61pci_init_txentry(struct rt2x00_dev *rt2x00dev,
struct queue_entry *entry)
{
- struct queue_entry_priv_pci_tx *priv_tx = entry->priv_data;
+ struct queue_entry_priv_pci *entry_priv = entry->priv_data;
u32 word;
- rt2x00_desc_read(priv_tx->desc, 0, &word);
+ rt2x00_desc_read(entry_priv->desc, 0, &word);
rt2x00_set_field32(&word, TXD_W0_VALID, 0);
rt2x00_set_field32(&word, TXD_W0_OWNER_NIC, 0);
- rt2x00_desc_write(priv_tx->desc, 0, word);
+ rt2x00_desc_write(entry_priv->desc, 0, word);
}
static int rt61pci_init_queues(struct rt2x00_dev *rt2x00dev)
{
- struct queue_entry_priv_pci_rx *priv_rx;
- struct queue_entry_priv_pci_tx *priv_tx;
+ struct queue_entry_priv_pci *entry_priv;
u32 reg;
/*
rt2x00dev->tx[0].desc_size / 4);
rt2x00pci_register_write(rt2x00dev, TX_RING_CSR1, reg);
- priv_tx = rt2x00dev->tx[0].entries[0].priv_data;
+ entry_priv = rt2x00dev->tx[0].entries[0].priv_data;
rt2x00pci_register_read(rt2x00dev, AC0_BASE_CSR, ®);
rt2x00_set_field32(®, AC0_BASE_CSR_RING_REGISTER,
- priv_tx->desc_dma);
+ entry_priv->desc_dma);
rt2x00pci_register_write(rt2x00dev, AC0_BASE_CSR, reg);
- priv_tx = rt2x00dev->tx[1].entries[0].priv_data;
+ entry_priv = rt2x00dev->tx[1].entries[0].priv_data;
rt2x00pci_register_read(rt2x00dev, AC1_BASE_CSR, ®);
rt2x00_set_field32(®, AC1_BASE_CSR_RING_REGISTER,
- priv_tx->desc_dma);
+ entry_priv->desc_dma);
rt2x00pci_register_write(rt2x00dev, AC1_BASE_CSR, reg);
- priv_tx = rt2x00dev->tx[2].entries[0].priv_data;
+ entry_priv = rt2x00dev->tx[2].entries[0].priv_data;
rt2x00pci_register_read(rt2x00dev, AC2_BASE_CSR, ®);
rt2x00_set_field32(®, AC2_BASE_CSR_RING_REGISTER,
- priv_tx->desc_dma);
+ entry_priv->desc_dma);
rt2x00pci_register_write(rt2x00dev, AC2_BASE_CSR, reg);
- priv_tx = rt2x00dev->tx[3].entries[0].priv_data;
+ entry_priv = rt2x00dev->tx[3].entries[0].priv_data;
rt2x00pci_register_read(rt2x00dev, AC3_BASE_CSR, ®);
rt2x00_set_field32(®, AC3_BASE_CSR_RING_REGISTER,
- priv_tx->desc_dma);
+ entry_priv->desc_dma);
rt2x00pci_register_write(rt2x00dev, AC3_BASE_CSR, reg);
rt2x00pci_register_read(rt2x00dev, RX_RING_CSR, ®);
rt2x00_set_field32(®, RX_RING_CSR_RXD_WRITEBACK_SIZE, 4);
rt2x00pci_register_write(rt2x00dev, RX_RING_CSR, reg);
- priv_rx = rt2x00dev->rx->entries[0].priv_data;
+ entry_priv = rt2x00dev->rx->entries[0].priv_data;
rt2x00pci_register_read(rt2x00dev, RX_BASE_CSR, ®);
rt2x00_set_field32(®, RX_BASE_CSR_RING_REGISTER,
- priv_rx->desc_dma);
+ entry_priv->desc_dma);
rt2x00pci_register_write(rt2x00dev, RX_BASE_CSR, reg);
rt2x00pci_register_read(rt2x00dev, TX_DMA_DST_CSR, ®);
rt2x00_set_field32(®, TXRX_CSR8_ACK_CTS_54MBS, 42);
rt2x00pci_register_write(rt2x00dev, TXRX_CSR8, reg);
+ rt2x00pci_register_read(rt2x00dev, TXRX_CSR9, ®);
+ rt2x00_set_field32(®, TXRX_CSR9_BEACON_INTERVAL, 0);
+ rt2x00_set_field32(®, TXRX_CSR9_TSF_TICKING, 0);
+ rt2x00_set_field32(®, TXRX_CSR9_TSF_SYNC, 0);
+ rt2x00_set_field32(®, TXRX_CSR9_TBTT_ENABLE, 0);
+ rt2x00_set_field32(®, TXRX_CSR9_BEACON_GEN, 0);
+ rt2x00_set_field32(®, TXRX_CSR9_TIMESTAMP_COMPENSATE, 0);
+ rt2x00pci_register_write(rt2x00dev, TXRX_CSR9, reg);
+
rt2x00pci_register_write(rt2x00dev, TXRX_CSR15, 0x0000000f);
rt2x00pci_register_write(rt2x00dev, MAC_CSR6, 0x00000fff);
rt2x00pci_register_write(rt2x00dev, M2H_CMD_DONE_CSR, 0xffffffff);
- rt2x00pci_register_read(rt2x00dev, AC_TXOP_CSR0, ®);
- rt2x00_set_field32(®, AC_TXOP_CSR0_AC0_TX_OP, 0);
- rt2x00_set_field32(®, AC_TXOP_CSR0_AC1_TX_OP, 0);
- rt2x00pci_register_write(rt2x00dev, AC_TXOP_CSR0, reg);
-
- rt2x00pci_register_read(rt2x00dev, AC_TXOP_CSR1, ®);
- rt2x00_set_field32(®, AC_TXOP_CSR1_AC2_TX_OP, 192);
- rt2x00_set_field32(®, AC_TXOP_CSR1_AC3_TX_OP, 48);
- rt2x00pci_register_write(rt2x00dev, AC_TXOP_CSR1, reg);
-
/*
* Clear all beacons
* For the Beacon base registers we only need to clear
return 0;
}
-static int rt61pci_init_bbp(struct rt2x00_dev *rt2x00dev)
+static int rt61pci_wait_bbp_ready(struct rt2x00_dev *rt2x00dev)
{
unsigned int i;
- u16 eeprom;
- u8 reg_id;
u8 value;
for (i = 0; i < REGISTER_BUSY_COUNT; i++) {
rt61pci_bbp_read(rt2x00dev, 0, &value);
if ((value != 0xff) && (value != 0x00))
- goto continue_csr_init;
- NOTICE(rt2x00dev, "Waiting for BBP register.\n");
+ return 0;
udelay(REGISTER_BUSY_DELAY);
}
ERROR(rt2x00dev, "BBP register access failed, aborting.\n");
return -EACCES;
+}
+
+static int rt61pci_init_bbp(struct rt2x00_dev *rt2x00dev)
+{
+ unsigned int i;
+ u16 eeprom;
+ u8 reg_id;
+ u8 value;
+
+ if (unlikely(rt61pci_wait_bbp_ready(rt2x00dev)))
+ return -EACCES;
-continue_csr_init:
rt61pci_bbp_write(rt2x00dev, 3, 0x00);
rt61pci_bbp_write(rt2x00dev, 15, 0x30);
rt61pci_bbp_write(rt2x00dev, 21, 0xc8);
rt2x00pci_register_read(rt2x00dev, TXRX_CSR0, ®);
rt2x00_set_field32(®, TXRX_CSR0_DISABLE_RX,
- state == STATE_RADIO_RX_OFF);
+ (state == STATE_RADIO_RX_OFF) ||
+ (state == STATE_RADIO_RX_OFF_LINK));
rt2x00pci_register_write(rt2x00dev, TXRX_CSR0, reg);
}
/*
* Initialize all registers.
*/
- if (rt61pci_init_queues(rt2x00dev) ||
- rt61pci_init_registers(rt2x00dev) ||
- rt61pci_init_bbp(rt2x00dev)) {
- ERROR(rt2x00dev, "Register initialization failed.\n");
+ if (unlikely(rt61pci_init_queues(rt2x00dev) ||
+ rt61pci_init_registers(rt2x00dev) ||
+ rt61pci_init_bbp(rt2x00dev)))
return -EIO;
- }
-
- /*
- * Enable interrupts.
- */
- rt61pci_toggle_irq(rt2x00dev, STATE_RADIO_IRQ_ON);
/*
* Enable RX.
rt2x00_set_field32(®, TX_CNTL_CSR_ABORT_TX_AC2, 1);
rt2x00_set_field32(®, TX_CNTL_CSR_ABORT_TX_AC3, 1);
rt2x00pci_register_write(rt2x00dev, TX_CNTL_CSR, reg);
-
- /*
- * Disable interrupts.
- */
- rt61pci_toggle_irq(rt2x00dev, STATE_RADIO_IRQ_OFF);
}
static int rt61pci_set_state(struct rt2x00_dev *rt2x00dev, enum dev_state state)
u32 reg;
unsigned int i;
char put_to_sleep;
- char current_state;
put_to_sleep = (state != STATE_AWAKE);
*/
for (i = 0; i < REGISTER_BUSY_COUNT; i++) {
rt2x00pci_register_read(rt2x00dev, MAC_CSR12, ®);
- current_state =
- rt2x00_get_field32(reg, MAC_CSR12_BBP_CURRENT_STATE);
- if (current_state == !put_to_sleep)
+ state = rt2x00_get_field32(reg, MAC_CSR12_BBP_CURRENT_STATE);
+ if (state == !put_to_sleep)
return 0;
msleep(10);
}
- NOTICE(rt2x00dev, "Device failed to enter state %d, "
- "current device state %d.\n", !put_to_sleep, current_state);
-
return -EBUSY;
}
break;
case STATE_RADIO_RX_ON:
case STATE_RADIO_RX_ON_LINK:
- rt61pci_toggle_rx(rt2x00dev, STATE_RADIO_RX_ON);
- break;
case STATE_RADIO_RX_OFF:
case STATE_RADIO_RX_OFF_LINK:
- rt61pci_toggle_rx(rt2x00dev, STATE_RADIO_RX_OFF);
+ rt61pci_toggle_rx(rt2x00dev, state);
+ break;
+ case STATE_RADIO_IRQ_ON:
+ case STATE_RADIO_IRQ_OFF:
+ rt61pci_toggle_irq(rt2x00dev, state);
break;
case STATE_DEEP_SLEEP:
case STATE_SLEEP:
break;
}
+ if (unlikely(retval))
+ ERROR(rt2x00dev, "Device failed to enter state %d (%d).\n",
+ state, retval);
+
return retval;
}
* TX descriptor initialization
*/
static void rt61pci_write_tx_desc(struct rt2x00_dev *rt2x00dev,
- struct sk_buff *skb,
- struct txentry_desc *txdesc)
+ struct sk_buff *skb,
+ struct txentry_desc *txdesc)
{
struct skb_frame_desc *skbdesc = get_skb_frame_desc(skb);
- struct queue_entry_priv_pci_tx *entry_priv = skbdesc->entry->priv_data;
__le32 *txd = skbdesc->desc;
u32 word;
rt2x00_set_field32(&word, TXD_W1_AIFSN, txdesc->aifs);
rt2x00_set_field32(&word, TXD_W1_CWMIN, txdesc->cw_min);
rt2x00_set_field32(&word, TXD_W1_CWMAX, txdesc->cw_max);
- rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, IEEE80211_HEADER);
- rt2x00_set_field32(&word, TXD_W1_HW_SEQUENCE, 1);
+ rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, txdesc->iv_offset);
+ rt2x00_set_field32(&word, TXD_W1_HW_SEQUENCE,
+ test_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags));
rt2x00_set_field32(&word, TXD_W1_BUFFER_COUNT, 1);
rt2x00_desc_write(txd, 1, word);
rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_HIGH, txdesc->length_high);
rt2x00_desc_write(txd, 2, word);
+ if (test_bit(ENTRY_TXD_ENCRYPT, &txdesc->flags)) {
+ _rt2x00_desc_write(txd, 3, skbdesc->iv);
+ _rt2x00_desc_write(txd, 4, skbdesc->eiv);
+ }
+
rt2x00_desc_read(txd, 5, &word);
rt2x00_set_field32(&word, TXD_W5_PID_TYPE, skbdesc->entry->queue->qid);
rt2x00_set_field32(&word, TXD_W5_PID_SUBTYPE,
rt2x00_desc_read(txd, 6, &word);
rt2x00_set_field32(&word, TXD_W6_BUFFER_PHYSICAL_ADDRESS,
- entry_priv->data_dma);
+ skbdesc->skb_dma);
rt2x00_desc_write(txd, 6, word);
if (skbdesc->desc_len > TXINFO_SIZE) {
rt2x00_desc_read(txd, 11, &word);
- rt2x00_set_field32(&word, TXD_W11_BUFFER_LENGTH0, skbdesc->data_len);
+ rt2x00_set_field32(&word, TXD_W11_BUFFER_LENGTH0, skb->len);
rt2x00_desc_write(txd, 11, word);
}
rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->ifs);
rt2x00_set_field32(&word, TXD_W0_RETRY_MODE,
test_bit(ENTRY_TXD_RETRY_MODE, &txdesc->flags));
- rt2x00_set_field32(&word, TXD_W0_TKIP_MIC, 0);
- rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, skbdesc->data_len);
+ rt2x00_set_field32(&word, TXD_W0_TKIP_MIC,
+ test_bit(ENTRY_TXD_ENCRYPT_MMIC, &txdesc->flags));
+ rt2x00_set_field32(&word, TXD_W0_KEY_TABLE,
+ test_bit(ENTRY_TXD_ENCRYPT_PAIRWISE, &txdesc->flags));
+ rt2x00_set_field32(&word, TXD_W0_KEY_INDEX, txdesc->key_idx);
+ rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, skb->len);
rt2x00_set_field32(&word, TXD_W0_BURST,
test_bit(ENTRY_TXD_BURST, &txdesc->flags));
- rt2x00_set_field32(&word, TXD_W0_CIPHER_ALG, CIPHER_NONE);
+ rt2x00_set_field32(&word, TXD_W0_CIPHER_ALG, txdesc->cipher);
rt2x00_desc_write(txd, 0, word);
}
/*
* TX data initialization
*/
+static void rt61pci_write_beacon(struct queue_entry *entry)
+{
+ struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
+ struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
+ unsigned int beacon_base;
+ u32 reg;
+
+ /*
+ * Disable beaconing while we are reloading the beacon data,
+ * otherwise we might be sending out invalid data.
+ */
+ rt2x00pci_register_read(rt2x00dev, TXRX_CSR9, ®);
+ rt2x00_set_field32(®, TXRX_CSR9_TSF_TICKING, 0);
+ rt2x00_set_field32(®, TXRX_CSR9_TBTT_ENABLE, 0);
+ rt2x00_set_field32(®, TXRX_CSR9_BEACON_GEN, 0);
+ rt2x00pci_register_write(rt2x00dev, TXRX_CSR9, reg);
+
+ /*
+ * Write entire beacon with descriptor to register.
+ */
+ beacon_base = HW_BEACON_OFFSET(entry->entry_idx);
+ rt2x00pci_register_multiwrite(rt2x00dev,
+ beacon_base,
+ skbdesc->desc, skbdesc->desc_len);
+ rt2x00pci_register_multiwrite(rt2x00dev,
+ beacon_base + skbdesc->desc_len,
+ entry->skb->data, entry->skb->len);
+
+ /*
+ * Clean up beacon skb.
+ */
+ dev_kfree_skb_any(entry->skb);
+ entry->skb = NULL;
+}
+
static void rt61pci_kick_tx_queue(struct rt2x00_dev *rt2x00dev,
const enum data_queue_qid queue)
{
*/
static int rt61pci_agc_to_rssi(struct rt2x00_dev *rt2x00dev, int rxd_w1)
{
- u16 eeprom;
- u8 offset;
+ u8 offset = rt2x00dev->lna_gain;
u8 lna;
lna = rt2x00_get_field32(rxd_w1, RXD_W1_RSSI_LNA);
switch (lna) {
case 3:
- offset = 90;
+ offset += 90;
break;
case 2:
- offset = 74;
+ offset += 74;
break;
case 1:
- offset = 64;
+ offset += 64;
break;
default:
return 0;
}
if (rt2x00dev->rx_status.band == IEEE80211_BAND_5GHZ) {
- if (test_bit(CONFIG_EXTERNAL_LNA_A, &rt2x00dev->flags))
- offset += 14;
-
if (lna == 3 || lna == 2)
offset += 10;
-
- rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_A, &eeprom);
- offset -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_A_1);
- } else {
- if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags))
- offset += 14;
-
- rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_BG, &eeprom);
- offset -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_BG_1);
}
return rt2x00_get_field32(rxd_w1, RXD_W1_RSSI_AGC) * 2 - offset;
static void rt61pci_fill_rxdone(struct queue_entry *entry,
struct rxdone_entry_desc *rxdesc)
{
- struct queue_entry_priv_pci_rx *priv_rx = entry->priv_data;
+ struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
+ struct queue_entry_priv_pci *entry_priv = entry->priv_data;
u32 word0;
u32 word1;
- rt2x00_desc_read(priv_rx->desc, 0, &word0);
- rt2x00_desc_read(priv_rx->desc, 1, &word1);
+ rt2x00_desc_read(entry_priv->desc, 0, &word0);
+ rt2x00_desc_read(entry_priv->desc, 1, &word1);
- rxdesc->flags = 0;
if (rt2x00_get_field32(word0, RXD_W0_CRC_ERROR))
rxdesc->flags |= RX_FLAG_FAILED_FCS_CRC;
+ if (test_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags)) {
+ rxdesc->cipher =
+ rt2x00_get_field32(word0, RXD_W0_CIPHER_ALG);
+ rxdesc->cipher_status =
+ rt2x00_get_field32(word0, RXD_W0_CIPHER_ERROR);
+ }
+
+ if (rxdesc->cipher != CIPHER_NONE) {
+ _rt2x00_desc_read(entry_priv->desc, 2, &rxdesc->iv);
+ _rt2x00_desc_read(entry_priv->desc, 3, &rxdesc->eiv);
+ _rt2x00_desc_read(entry_priv->desc, 4, &rxdesc->icv);
+
+ /*
+ * Hardware has stripped IV/EIV data from 802.11 frame during
+ * decryption. It has provided the data seperately but rt2x00lib
+ * should decide if it should be reinserted.
+ */
+ rxdesc->flags |= RX_FLAG_IV_STRIPPED;
+
+ /*
+ * FIXME: Legacy driver indicates that the frame does
+ * contain the Michael Mic. Unfortunately, in rt2x00
+ * the MIC seems to be missing completely...
+ */
+ rxdesc->flags |= RX_FLAG_MMIC_STRIPPED;
+
+ if (rxdesc->cipher_status == RX_CRYPTO_SUCCESS)
+ rxdesc->flags |= RX_FLAG_DECRYPTED;
+ else if (rxdesc->cipher_status == RX_CRYPTO_FAIL_MIC)
+ rxdesc->flags |= RX_FLAG_MMIC_ERROR;
+ }
+
/*
* Obtain the status about this packet.
* When frame was received with an OFDM bitrate,
* a CCK bitrate the signal is the rate in 100kbit/s.
*/
rxdesc->signal = rt2x00_get_field32(word1, RXD_W1_SIGNAL);
- rxdesc->rssi = rt61pci_agc_to_rssi(entry->queue->rt2x00dev, word1);
+ rxdesc->rssi = rt61pci_agc_to_rssi(rt2x00dev, word1);
rxdesc->size = rt2x00_get_field32(word0, RXD_W0_DATABYTE_COUNT);
- rxdesc->dev_flags = 0;
if (rt2x00_get_field32(word0, RXD_W0_OFDM))
rxdesc->dev_flags |= RXDONE_SIGNAL_PLCP;
+ else
+ rxdesc->dev_flags |= RXDONE_SIGNAL_BITRATE;
if (rt2x00_get_field32(word0, RXD_W0_MY_BSS))
rxdesc->dev_flags |= RXDONE_MY_BSS;
}
struct data_queue *queue;
struct queue_entry *entry;
struct queue_entry *entry_done;
- struct queue_entry_priv_pci_tx *priv_tx;
+ struct queue_entry_priv_pci *entry_priv;
struct txdone_entry_desc txdesc;
u32 word;
u32 reg;
continue;
entry = &queue->entries[index];
- priv_tx = entry->priv_data;
- rt2x00_desc_read(priv_tx->desc, 0, &word);
+ entry_priv = entry->priv_data;
+ rt2x00_desc_read(entry_priv->desc, 0, &word);
if (rt2x00_get_field32(word, TXD_W0_OWNER_NIC) ||
!rt2x00_get_field32(word, TXD_W0_VALID))
__set_bit(TXDONE_UNKNOWN, &txdesc.flags);
txdesc.retry = 0;
- rt2x00pci_txdone(rt2x00dev, entry_done, &txdesc);
+ rt2x00lib_txdone(entry_done, &txdesc);
entry_done = rt2x00queue_get_entry(queue, Q_INDEX_DONE);
}
}
txdesc.retry = rt2x00_get_field32(reg, STA_CSR4_RETRY_COUNT);
- rt2x00pci_txdone(rt2x00dev, entry, &txdesc);
+ rt2x00lib_txdone(entry, &txdesc);
}
}
if (!reg && !reg_mcu)
return IRQ_NONE;
- if (!test_bit(DEVICE_ENABLED_RADIO, &rt2x00dev->flags))
+ if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
return IRQ_HANDLED;
/*
* To determine the RT chip we have to read the
* PCI header of the device.
*/
- pci_read_config_word(rt2x00dev_pci(rt2x00dev),
+ pci_read_config_word(to_pci_dev(rt2x00dev->dev),
PCI_CONFIG_HEADER_DEVICE, &device);
value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RF_TYPE);
rt2x00pci_register_read(rt2x00dev, MAC_CSR0, ®);
/*
* Detect if this device has an hardware controlled radio.
*/
-#ifdef CONFIG_RT61PCI_RFKILL
+#ifdef CONFIG_RT2X00_LIB_RFKILL
if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_HARDWARE_RADIO))
__set_bit(CONFIG_SUPPORT_HW_BUTTON, &rt2x00dev->flags);
-#endif /* CONFIG_RT61PCI_RFKILL */
+#endif /* CONFIG_RT2X00_LIB_RFKILL */
/*
* Read frequency offset and RF programming sequence.
* If the eeprom value is invalid,
* switch to default led mode.
*/
-#ifdef CONFIG_RT61PCI_LEDS
+#ifdef CONFIG_RT2X00_LIB_LEDS
rt2x00_eeprom_read(rt2x00dev, EEPROM_LED, &eeprom);
value = rt2x00_get_field16(eeprom, EEPROM_LED_LED_MODE);
- rt2x00dev->led_radio.rt2x00dev = rt2x00dev;
- rt2x00dev->led_radio.type = LED_TYPE_RADIO;
- rt2x00dev->led_radio.led_dev.brightness_set =
- rt61pci_brightness_set;
- rt2x00dev->led_radio.led_dev.blink_set =
- rt61pci_blink_set;
- rt2x00dev->led_radio.flags = LED_INITIALIZED;
-
- rt2x00dev->led_assoc.rt2x00dev = rt2x00dev;
- rt2x00dev->led_assoc.type = LED_TYPE_ASSOC;
- rt2x00dev->led_assoc.led_dev.brightness_set =
- rt61pci_brightness_set;
- rt2x00dev->led_assoc.led_dev.blink_set =
- rt61pci_blink_set;
- rt2x00dev->led_assoc.flags = LED_INITIALIZED;
-
- if (value == LED_MODE_SIGNAL_STRENGTH) {
- rt2x00dev->led_qual.rt2x00dev = rt2x00dev;
- rt2x00dev->led_qual.type = LED_TYPE_QUALITY;
- rt2x00dev->led_qual.led_dev.brightness_set =
- rt61pci_brightness_set;
- rt2x00dev->led_qual.led_dev.blink_set =
- rt61pci_blink_set;
- rt2x00dev->led_qual.flags = LED_INITIALIZED;
- }
+ rt61pci_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO);
+ rt61pci_init_led(rt2x00dev, &rt2x00dev->led_assoc, LED_TYPE_ASSOC);
+ if (value == LED_MODE_SIGNAL_STRENGTH)
+ rt61pci_init_led(rt2x00dev, &rt2x00dev->led_qual,
+ LED_TYPE_QUALITY);
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_LED_MODE, value);
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_GPIO_0,
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_READY_A,
rt2x00_get_field16(eeprom,
EEPROM_LED_POLARITY_RDY_A));
-#endif /* CONFIG_RT61PCI_LEDS */
+#endif /* CONFIG_RT2X00_LIB_LEDS */
return 0;
}
{ 46, 0x00002ccc, 0x000049a6, 0x0009be55, 0x000c0a23 },
};
-static void rt61pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
+static int rt61pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
{
struct hw_mode_spec *spec = &rt2x00dev->spec;
- u8 *txpower;
+ struct channel_info *info;
+ char *tx_power;
unsigned int i;
/*
* Initialize all hw fields.
*/
rt2x00dev->hw->flags =
- IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
IEEE80211_HW_SIGNAL_DBM;
rt2x00dev->hw->extra_tx_headroom = 0;
- SET_IEEE80211_DEV(rt2x00dev->hw, &rt2x00dev_pci(rt2x00dev)->dev);
+ SET_IEEE80211_DEV(rt2x00dev->hw, rt2x00dev->dev);
SET_IEEE80211_PERM_ADDR(rt2x00dev->hw,
rt2x00_eeprom_addr(rt2x00dev,
EEPROM_MAC_ADDR_0));
/*
- * Convert tx_power array in eeprom.
- */
- txpower = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_G_START);
- for (i = 0; i < 14; i++)
- txpower[i] = TXPOWER_FROM_DEV(txpower[i]);
-
- /*
* Initialize hw_mode information.
*/
spec->supported_bands = SUPPORT_BAND_2GHZ;
spec->supported_rates = SUPPORT_RATE_CCK | SUPPORT_RATE_OFDM;
- spec->tx_power_a = NULL;
- spec->tx_power_bg = txpower;
- spec->tx_power_default = DEFAULT_TXPOWER;
if (!test_bit(CONFIG_RF_SEQUENCE, &rt2x00dev->flags)) {
spec->num_channels = 14;
rt2x00_rf(&rt2x00dev->chip, RF5325)) {
spec->supported_bands |= SUPPORT_BAND_5GHZ;
spec->num_channels = ARRAY_SIZE(rf_vals_seq);
+ }
+
+ /*
+ * Create channel information array
+ */
+ info = kzalloc(spec->num_channels * sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ spec->channels_info = info;
- txpower = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_A_START);
- for (i = 0; i < 14; i++)
- txpower[i] = TXPOWER_FROM_DEV(txpower[i]);
+ tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_G_START);
+ for (i = 0; i < 14; i++)
+ info[i].tx_power1 = TXPOWER_FROM_DEV(tx_power[i]);
- spec->tx_power_a = txpower;
+ if (spec->num_channels > 14) {
+ tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_A_START);
+ for (i = 14; i < spec->num_channels; i++)
+ info[i].tx_power1 = TXPOWER_FROM_DEV(tx_power[i]);
}
+
+ return 0;
}
static int rt61pci_probe_hw(struct rt2x00_dev *rt2x00dev)
/*
* Initialize hw specifications.
*/
- rt61pci_probe_hw_mode(rt2x00dev);
+ retval = rt61pci_probe_hw_mode(rt2x00dev);
+ if (retval)
+ return retval;
/*
- * This device requires firmware.
+ * This device requires firmware and DMA mapped skbs.
*/
__set_bit(DRIVER_REQUIRE_FIRMWARE, &rt2x00dev->flags);
+ __set_bit(DRIVER_REQUIRE_DMA, &rt2x00dev->flags);
+ if (!modparam_nohwcrypt)
+ __set_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags);
/*
* Set the rssi offset.
return 0;
}
-static u64 rt61pci_get_tsf(struct ieee80211_hw *hw)
+static int rt61pci_conf_tx(struct ieee80211_hw *hw, u16 queue_idx,
+ const struct ieee80211_tx_queue_params *params)
{
struct rt2x00_dev *rt2x00dev = hw->priv;
- u64 tsf;
+ struct data_queue *queue;
+ struct rt2x00_field32 field;
+ int retval;
u32 reg;
- rt2x00pci_register_read(rt2x00dev, TXRX_CSR13, ®);
- tsf = (u64) rt2x00_get_field32(reg, TXRX_CSR13_HIGH_TSFTIMER) << 32;
- rt2x00pci_register_read(rt2x00dev, TXRX_CSR12, ®);
- tsf |= rt2x00_get_field32(reg, TXRX_CSR12_LOW_TSFTIMER);
+ /*
+ * First pass the configuration through rt2x00lib, that will
+ * update the queue settings and validate the input. After that
+ * we are free to update the registers based on the value
+ * in the queue parameter.
+ */
+ retval = rt2x00mac_conf_tx(hw, queue_idx, params);
+ if (retval)
+ return retval;
- return tsf;
-}
+ queue = rt2x00queue_get_queue(rt2x00dev, queue_idx);
-static int rt61pci_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb,
- struct ieee80211_tx_control *control)
-{
- struct rt2x00_dev *rt2x00dev = hw->priv;
- struct rt2x00_intf *intf = vif_to_intf(control->vif);
- struct queue_entry_priv_pci_tx *priv_tx;
- struct skb_frame_desc *skbdesc;
- unsigned int beacon_base;
- u32 reg;
+ /* Update WMM TXOP register */
+ if (queue_idx < 2) {
+ field.bit_offset = queue_idx * 16;
+ field.bit_mask = 0xffff << field.bit_offset;
- if (unlikely(!intf->beacon))
- return -ENOBUFS;
+ rt2x00pci_register_read(rt2x00dev, AC_TXOP_CSR0, ®);
+ rt2x00_set_field32(®, field, queue->txop);
+ rt2x00pci_register_write(rt2x00dev, AC_TXOP_CSR0, reg);
+ } else if (queue_idx < 4) {
+ field.bit_offset = (queue_idx - 2) * 16;
+ field.bit_mask = 0xffff << field.bit_offset;
- priv_tx = intf->beacon->priv_data;
- memset(priv_tx->desc, 0, intf->beacon->queue->desc_size);
+ rt2x00pci_register_read(rt2x00dev, AC_TXOP_CSR1, ®);
+ rt2x00_set_field32(®, field, queue->txop);
+ rt2x00pci_register_write(rt2x00dev, AC_TXOP_CSR1, reg);
+ }
- /*
- * Fill in skb descriptor
- */
- skbdesc = get_skb_frame_desc(skb);
- memset(skbdesc, 0, sizeof(*skbdesc));
- skbdesc->flags |= FRAME_DESC_DRIVER_GENERATED;
- skbdesc->data = skb->data;
- skbdesc->data_len = skb->len;
- skbdesc->desc = priv_tx->desc;
- skbdesc->desc_len = intf->beacon->queue->desc_size;
- skbdesc->entry = intf->beacon;
+ /* Update WMM registers */
+ field.bit_offset = queue_idx * 4;
+ field.bit_mask = 0xf << field.bit_offset;
- /*
- * Disable beaconing while we are reloading the beacon data,
- * otherwise we might be sending out invalid data.
- */
- rt2x00pci_register_read(rt2x00dev, TXRX_CSR9, ®);
- rt2x00_set_field32(®, TXRX_CSR9_TSF_TICKING, 0);
- rt2x00_set_field32(®, TXRX_CSR9_TBTT_ENABLE, 0);
- rt2x00_set_field32(®, TXRX_CSR9_BEACON_GEN, 0);
- rt2x00pci_register_write(rt2x00dev, TXRX_CSR9, reg);
+ rt2x00pci_register_read(rt2x00dev, AIFSN_CSR, ®);
+ rt2x00_set_field32(®, field, queue->aifs);
+ rt2x00pci_register_write(rt2x00dev, AIFSN_CSR, reg);
- /*
- * Write entire beacon with descriptor to register,
- * and kick the beacon generator.
- */
- rt2x00lib_write_tx_desc(rt2x00dev, skb, control);
- beacon_base = HW_BEACON_OFFSET(intf->beacon->entry_idx);
- rt2x00pci_register_multiwrite(rt2x00dev, beacon_base,
- skbdesc->desc, skbdesc->desc_len);
- rt2x00pci_register_multiwrite(rt2x00dev,
- beacon_base + skbdesc->desc_len,
- skbdesc->data, skbdesc->data_len);
- rt61pci_kick_tx_queue(rt2x00dev, QID_BEACON);
+ rt2x00pci_register_read(rt2x00dev, CWMIN_CSR, ®);
+ rt2x00_set_field32(®, field, queue->cw_min);
+ rt2x00pci_register_write(rt2x00dev, CWMIN_CSR, reg);
+
+ rt2x00pci_register_read(rt2x00dev, CWMAX_CSR, ®);
+ rt2x00_set_field32(®, field, queue->cw_max);
+ rt2x00pci_register_write(rt2x00dev, CWMAX_CSR, reg);
return 0;
}
+static u64 rt61pci_get_tsf(struct ieee80211_hw *hw)
+{
+ struct rt2x00_dev *rt2x00dev = hw->priv;
+ u64 tsf;
+ u32 reg;
+
+ rt2x00pci_register_read(rt2x00dev, TXRX_CSR13, ®);
+ tsf = (u64) rt2x00_get_field32(reg, TXRX_CSR13_HIGH_TSFTIMER) << 32;
+ rt2x00pci_register_read(rt2x00dev, TXRX_CSR12, ®);
+ tsf |= rt2x00_get_field32(reg, TXRX_CSR12_LOW_TSFTIMER);
+
+ return tsf;
+}
+
static const struct ieee80211_ops rt61pci_mac80211_ops = {
.tx = rt2x00mac_tx,
.start = rt2x00mac_start,
.config = rt2x00mac_config,
.config_interface = rt2x00mac_config_interface,
.configure_filter = rt2x00mac_configure_filter,
+ .set_key = rt2x00mac_set_key,
.get_stats = rt2x00mac_get_stats,
.set_retry_limit = rt61pci_set_retry_limit,
.bss_info_changed = rt2x00mac_bss_info_changed,
- .conf_tx = rt2x00mac_conf_tx,
+ .conf_tx = rt61pci_conf_tx,
.get_tx_stats = rt2x00mac_get_tx_stats,
.get_tsf = rt61pci_get_tsf,
- .beacon_update = rt61pci_beacon_update,
};
static const struct rt2x00lib_ops rt61pci_rt2x00_ops = {
.link_tuner = rt61pci_link_tuner,
.write_tx_desc = rt61pci_write_tx_desc,
.write_tx_data = rt2x00pci_write_tx_data,
+ .write_beacon = rt61pci_write_beacon,
.kick_tx_queue = rt61pci_kick_tx_queue,
.fill_rxdone = rt61pci_fill_rxdone,
+ .config_shared_key = rt61pci_config_shared_key,
+ .config_pairwise_key = rt61pci_config_pairwise_key,
.config_filter = rt61pci_config_filter,
.config_intf = rt61pci_config_intf,
.config_erp = rt61pci_config_erp,
.entry_num = RX_ENTRIES,
.data_size = DATA_FRAME_SIZE,
.desc_size = RXD_DESC_SIZE,
- .priv_size = sizeof(struct queue_entry_priv_pci_rx),
+ .priv_size = sizeof(struct queue_entry_priv_pci),
};
static const struct data_queue_desc rt61pci_queue_tx = {
.entry_num = TX_ENTRIES,
.data_size = DATA_FRAME_SIZE,
.desc_size = TXD_DESC_SIZE,
- .priv_size = sizeof(struct queue_entry_priv_pci_tx),
+ .priv_size = sizeof(struct queue_entry_priv_pci),
};
static const struct data_queue_desc rt61pci_queue_bcn = {
.entry_num = 4 * BEACON_ENTRIES,
.data_size = 0, /* No DMA required for beacons */
.desc_size = TXINFO_SIZE,
- .priv_size = sizeof(struct queue_entry_priv_pci_tx),
+ .priv_size = sizeof(struct queue_entry_priv_pci),
};
static const struct rt2x00_ops rt61pci_ops = {