*
* GPL LICENSE SUMMARY
*
- * Copyright(c) 2008 Intel Corporation. All rights reserved.
+ * Copyright(c) 2008 - 2010 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
*
* BSD LICENSE
*
- * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
+ * Copyright(c) 2005 - 2010 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
#ifndef __iwl_eeprom_h__
#define __iwl_eeprom_h__
+#include <net/mac80211.h>
+
struct iwl_priv;
/*
* EEPROM access time values:
*
- * Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG,
- * then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit
- * CSR_EEPROM_REG_BIT_CMD (0x2).
+ * Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG.
* Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1).
* When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec.
* Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG.
*/
#define IWL_EEPROM_ACCESS_TIMEOUT 5000 /* uSec */
-#define IWL_EEPROM_ACCESS_DELAY 10 /* uSec */
-#define IWL_EEPROM_SEM_TIMEOUT 10 /* milliseconds */
+#define IWL_EEPROM_SEM_TIMEOUT 10 /* microseconds */
#define IWL_EEPROM_SEM_RETRY_LIMIT 1000 /* number of attempts (not time) */
* requirement for establishing a new network for legal operation on channels
* requiring RADAR detection or restricting ACTIVE scanning.
*
- * NOTE: "WIDE" flag does not indicate anything about "FAT" 40 MHz channels.
- * It only indicates that 20 MHz channel use is supported; FAT channel
+ * NOTE: "WIDE" flag does not indicate anything about "HT40" 40 MHz channels.
+ * It only indicates that 20 MHz channel use is supported; HT40 channel
* usage is indicated by a separate set of regulatory flags for each
- * FAT channel pair.
+ * HT40 channel pair.
*
* NOTE: Using a channel inappropriately will result in a uCode error!
*/
#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE (1 << 1)
/* *regulatory* channel data format in eeprom, one for each channel.
- * There are separate entries for FAT (40 MHz) vs. normal (20 MHz) channels. */
+ * There are separate entries for HT40 (40 MHz) vs. normal (20 MHz) channels. */
struct iwl_eeprom_channel {
u8 flags; /* EEPROM_CHANNEL_* flags copied from EEPROM */
s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */
} __attribute__ ((packed));
+/**
+ * iwl_eeprom_enhanced_txpwr structure
+ * This structure presents the enhanced regulatory tx power limit layout
+ * in eeprom image
+ * Enhanced regulatory tx power portion of eeprom image can be broken down
+ * into individual structures; each one is 8 bytes in size and contain the
+ * following information
+ * @common: (desc + channel) not used by driver, should _NOT_ be "zero"
+ * @chain_a_max_pwr: chain a max power in 1/2 dBm
+ * @chain_b_max_pwr: chain b max power in 1/2 dBm
+ * @chain_c_max_pwr: chain c max power in 1/2 dBm
+ * @reserved: not used, should be "zero"
+ * @mimo2_max_pwr: mimo2 max power in 1/2 dBm
+ * @mimo3_max_pwr: mimo3 max power in 1/2 dBm
+ *
+ */
+struct iwl_eeprom_enhanced_txpwr {
+ __le16 common;
+ s8 chain_a_max;
+ s8 chain_b_max;
+ s8 chain_c_max;
+ s8 reserved;
+ s8 mimo2_max;
+ s8 mimo3_max;
+} __attribute__ ((packed));
+
+/* 3945 Specific */
+#define EEPROM_3945_EEPROM_VERSION (0x2f)
+
/* 4965 has two radio transmitters (and 3 radio receivers) */
#define EEPROM_TX_POWER_TX_CHAINS (2)
| INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 22 bytes */
#define EEPROM_5000_REG_BAND_5_CHANNELS ((0x74)\
| INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 12 bytes */
-#define EEPROM_5000_REG_BAND_24_FAT_CHANNELS ((0x82)\
+#define EEPROM_5000_REG_BAND_24_HT40_CHANNELS ((0x82)\
| INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 14 bytes */
-#define EEPROM_5000_REG_BAND_52_FAT_CHANNELS ((0x92)\
+#define EEPROM_5000_REG_BAND_52_HT40_CHANNELS ((0x92)\
| INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 22 bytes */
+/* 6000 regulatory - indirect access */
+#define EEPROM_6000_REG_BAND_24_HT40_CHANNELS ((0x80)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 14 bytes */
+
+/* 6000 and up regulatory tx power - indirect access */
+/* max. elements per section */
+#define EEPROM_MAX_TXPOWER_SECTION_ELEMENTS (8)
+#define EEPROM_TXPOWER_COMMON_HT40_INDEX (2)
+
+/**
+ * Partition the enhanced tx power portion of eeprom image into
+ * 10 sections based on band, modulation, frequency and channel
+ *
+ * Section 1: all CCK channels
+ * Section 2: all 2.4 GHz OFDM (Legacy, HT and HT40 ) channels
+ * Section 3: all 5.2 GHz OFDM (Legacy, HT and HT40) channels
+ * Section 4: 2.4 GHz 20MHz channels: 1, 2, 10, 11. Both Legacy and HT
+ * Section 5: 2.4 GHz 40MHz channels: 1, 2, 6, 7, 9, (_above_)
+ * Section 6: 5.2 GHz 20MHz channels: 36, 64, 100, both Legacy and HT
+ * Section 7: 5.2 GHz 40MHz channels: 36, 60, 100 (_above_)
+ * Section 8: 2.4 GHz channel 13, Both Legacy and HT
+ * Section 9: 2.4 GHz channel 140, Both Legacy and HT
+ * Section 10: 2.4 GHz 40MHz channels: 132, 44 (_above_)
+ */
+/* 2.4 GHz band: CCK */
+#define EEPROM_LB_CCK_20_COMMON ((0xA8)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 8 bytes */
+/* 2.4 GHz band: 20MHz-Legacy, 20MHz-HT, 40MHz-HT */
+#define EEPROM_LB_OFDM_COMMON ((0xB0)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 24 bytes */
+/* 5.2 GHz band: 20MHz-Legacy, 20MHz-HT, 40MHz-HT */
+#define EEPROM_HB_OFDM_COMMON ((0xC8)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 24 bytes */
+/* 2.4GHz band channels:
+ * 1Legacy, 1HT, 2Legacy, 2HT, 10Legacy, 10HT, 11Legacy, 11HT */
+#define EEPROM_LB_OFDM_20_BAND ((0xE0)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 64 bytes */
+/* 2.4 GHz band HT40 channels: (1,+1) (2,+1) (6,+1) (7,+1) (9,+1) */
+#define EEPROM_LB_OFDM_HT40_BAND ((0x120)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 40 bytes */
+/* 5.2GHz band channels: 36Legacy, 36HT, 64Legacy, 64HT, 100Legacy, 100HT */
+#define EEPROM_HB_OFDM_20_BAND ((0x148)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 48 bytes */
+/* 5.2 GHz band HT40 channels: (36,+1) (60,+1) (100,+1) */
+#define EEPROM_HB_OFDM_HT40_BAND ((0x178)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 24 bytes */
+/* 2.4 GHz band, channnel 13: Legacy, HT */
+#define EEPROM_LB_OFDM_20_CHANNEL_13 ((0x190)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 16 bytes */
+/* 5.2 GHz band, channnel 140: Legacy, HT */
+#define EEPROM_HB_OFDM_20_CHANNEL_140 ((0x1A0)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 16 bytes */
+/* 5.2 GHz band, HT40 channnels (132,+1) (44,+1) */
+#define EEPROM_HB_OFDM_HT40_BAND_1 ((0x1B0)\
+ | INDIRECT_ADDRESS | INDIRECT_REGULATORY) /* 16 bytes */
+
+
/* 5050 Specific */
#define EEPROM_5050_TX_POWER_VERSION (4)
#define EEPROM_5050_EEPROM_VERSION (0x21E)
+/* 1000 Specific */
+#define EEPROM_1000_EEPROM_VERSION (0x15C)
+
+/* 6x00 Specific */
+#define EEPROM_6000_EEPROM_VERSION (0x434)
+
+/* 6x50 Specific */
+#define EEPROM_6050_EEPROM_VERSION (0x532)
+
+/* OTP */
+/* lower blocks contain EEPROM image and calibration data */
+#define OTP_LOW_IMAGE_SIZE (2 * 512 * sizeof(u16)) /* 2 KB */
+/* high blocks contain PAPD data */
+#define OTP_HIGH_IMAGE_SIZE_6x00 (6 * 512 * sizeof(u16)) /* 6 KB */
+#define OTP_HIGH_IMAGE_SIZE_1000 (0x200 * sizeof(u16)) /* 1024 bytes */
+#define OTP_MAX_LL_ITEMS_1000 (3) /* OTP blocks for 1000 */
+#define OTP_MAX_LL_ITEMS_6x00 (4) /* OTP blocks for 6x00 */
+#define OTP_MAX_LL_ITEMS_6x50 (7) /* OTP blocks for 6x50 */
+
/* 2.4 GHz */
extern const u8 iwl_eeprom_band_1[14];
struct iwl_eeprom_calib_info {
u8 saturation_power24; /* half-dBm (e.g. "34" = 17 dBm) */
u8 saturation_power52; /* half-dBm */
- s16 voltage; /* signed */
+ __le16 voltage; /* signed */
struct iwl_eeprom_calib_subband_info
band_info[EEPROM_TX_POWER_BANDS];
} __attribute__ ((packed));
#define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */
#define EEPROM_VERSION (2*0x44) /* 2 bytes */
#define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */
-#define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */
#define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */
#define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */
#define EEPROM_RADIO_CONFIG (2*0x48) /* 2 bytes */
#define EEPROM_3945_M_VERSION (2*0x4A) /* 1 bytes */
-#define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */
/* The following masks are to be applied on EEPROM_RADIO_CONFIG */
#define EEPROM_RF_CFG_TYPE_MSK(x) (x & 0x3) /* bits 0-1 */
#define EEPROM_3945_RF_CFG_TYPE_MAX 0x0
#define EEPROM_4965_RF_CFG_TYPE_MAX 0x1
-#define EEPROM_5000_RF_CFG_TYPE_MAX 0x3
+
+/* Radio Config for 5000 and up */
+#define EEPROM_RF_CONFIG_TYPE_R3x3 0x0
+#define EEPROM_RF_CONFIG_TYPE_R2x2 0x1
+#define EEPROM_RF_CONFIG_TYPE_R1x2 0x2
+#define EEPROM_RF_CONFIG_TYPE_MAX 0x3
/*
* Per-channel regulatory data.
* in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
* txpower (MSB).
*
- * Entries immediately below are for 20 MHz channel width. FAT (40 MHz)
+ * Entries immediately below are for 20 MHz channel width. HT40 (40 MHz)
* channels (only for 4965, not supported by 3945) appear later in the EEPROM.
*
* 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
#define EEPROM_REGULATORY_BAND_5_CHANNELS (2*0x99) /* 12 bytes */
/*
- * 2.4 GHz FAT channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11)
+ * 2.4 GHz HT40 channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11)
*
* The channel listed is the center of the lower 20 MHz half of the channel.
* The overall center frequency is actually 2 channels (10 MHz) above that,
- * and the upper half of each FAT channel is centered 4 channels (20 MHz) away
- * from the lower half; e.g. the upper half of FAT channel 1 is channel 5,
- * and the overall FAT channel width centers on channel 3.
+ * and the upper half of each HT40 channel is centered 4 channels (20 MHz) away
+ * from the lower half; e.g. the upper half of HT40 channel 1 is channel 5,
+ * and the overall HT40 channel width centers on channel 3.
*
* NOTE: The RXON command uses 20 MHz channel numbers to specify the
* control channel to which to tune. RXON also specifies whether the
- * control channel is the upper or lower half of a FAT channel.
+ * control channel is the upper or lower half of a HT40 channel.
*
- * NOTE: 4965 does not support FAT channels on 2.4 GHz.
+ * NOTE: 4965 does not support HT40 channels on 2.4 GHz.
*/
-#define EEPROM_4965_REGULATORY_BAND_24_FAT_CHANNELS (2*0xA0) /* 14 bytes */
+#define EEPROM_4965_REGULATORY_BAND_24_HT40_CHANNELS (2*0xA0) /* 14 bytes */
/*
- * 5.2 GHz FAT channels 36 (40), 44 (48), 52 (56), 60 (64),
+ * 5.2 GHz HT40 channels 36 (40), 44 (48), 52 (56), 60 (64),
* 100 (104), 108 (112), 116 (120), 124 (128), 132 (136), 149 (153), 157 (161)
*/
-#define EEPROM_4965_REGULATORY_BAND_52_FAT_CHANNELS (2*0xA8) /* 22 bytes */
+#define EEPROM_4965_REGULATORY_BAND_52_HT40_CHANNELS (2*0xA8) /* 22 bytes */
+
+#define EEPROM_REGULATORY_BAND_NO_HT40 (0)
struct iwl_eeprom_ops {
const u32 regulatory_bands[7];
void (*release_semaphore) (struct iwl_priv *priv);
u16 (*calib_version) (struct iwl_priv *priv);
const u8* (*query_addr) (const struct iwl_priv *priv, size_t offset);
+ void (*update_enhanced_txpower) (struct iwl_priv *priv);
};
int iwlcore_eeprom_acquire_semaphore(struct iwl_priv *priv);
void iwlcore_eeprom_release_semaphore(struct iwl_priv *priv);
const u8 *iwlcore_eeprom_query_addr(const struct iwl_priv *priv, size_t offset);
-
+void iwlcore_eeprom_enhanced_txpower(struct iwl_priv *priv);
int iwl_init_channel_map(struct iwl_priv *priv);
void iwl_free_channel_map(struct iwl_priv *priv);
const struct iwl_channel_info *iwl_get_channel_info(
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff