REPLY_TX_LINK_QUALITY_CMD = 0x4e, /* 4965 only */
/* WiMAX coexistence */
- COEX_PRIORITY_TABLE_CMD = 0x5a, /*5000 only */
+ COEX_PRIORITY_TABLE_CMD = 0x5a, /* for 5000 series and up */
COEX_MEDIUM_NOTIFICATION = 0x5b,
COEX_EVENT_CMD = 0x5c,
/* Calibration */
+ TEMPERATURE_NOTIFICATION = 0x62,
CALIBRATION_CFG_CMD = 0x65,
CALIBRATION_RES_NOTIFICATION = 0x66,
CALIBRATION_COMPLETE_NOTIFICATION = 0x67,
WHO_IS_AWAKE_NOTIFICATION = 0x94, /* not used */
/* Miscellaneous commands */
+ REPLY_TX_POWER_DBM_CMD = 0x95,
QUIET_NOTIFICATION = 0x96, /* not used */
REPLY_TX_PWR_TABLE_CMD = 0x97,
- REPLY_TX_POWER_DBM_CMD = 0x98,
+ REPLY_TX_POWER_DBM_CMD_V1 = 0x98, /* old version of API */
+ TX_ANT_CONFIGURATION_CMD = 0x98,
MEASURE_ABORT_NOTIFICATION = 0x99, /* not used */
/* Bluetooth device coexistence config command */
* 1) Dual stream (MIMO)
* 2) Triple stream (MIMO)
*
- * 5: Value of 0x20 in bits 7:0 indicates 6 Mbps FAT duplicate data
+ * 5: Value of 0x20 in bits 7:0 indicates 6 Mbps HT40 duplicate data
*
* Legacy OFDM rate format for bits 7:0 (bit 8 must be "0", bit 9 "0"):
* 3-0: 0xD) 6 Mbps
#define RATE_MCS_GF_POS 10
#define RATE_MCS_GF_MSK 0x400
-/* Bit 11: (1) Use 40Mhz FAT chnl width, (0) use 20 MHz legacy chnl width */
-#define RATE_MCS_FAT_POS 11
-#define RATE_MCS_FAT_MSK 0x800
+/* Bit 11: (1) Use 40Mhz HT40 chnl width, (0) use 20 MHz legacy chnl width */
+#define RATE_MCS_HT40_POS 11
+#define RATE_MCS_HT40_MSK 0x800
-/* Bit 12: (1) Duplicate data on both 20MHz chnls. FAT (bit 11) must be set. */
+/* Bit 12: (1) Duplicate data on both 20MHz chnls. HT40 (bit 11) must be set. */
#define RATE_MCS_DUP_POS 12
#define RATE_MCS_DUP_MSK 0x1000
#define POWER_TABLE_NUM_HT_OFDM_ENTRIES 32
#define POWER_TABLE_CCK_ENTRY 32
+#define IWL_PWR_NUM_HT_OFDM_ENTRIES 24
+#define IWL_PWR_CCK_ENTRIES 2
+
/**
* union iwl4965_tx_power_dual_stream
*
u8 reserved;
} __attribute__ ((packed));
+/**
+ * Command TX_ANT_CONFIGURATION_CMD = 0x98
+ * This command is used to configure valid Tx antenna.
+ * By default uCode concludes the valid antenna according to the radio flavor.
+ * This command enables the driver to override/modify this conclusion.
+ */
+struct iwl_tx_ant_config_cmd {
+ __le32 valid;
+} __attribute__ ((packed));
+
/******************************************************************************
* (0a)
* Alive and Error Commands & Responses:
/* calibration values from "initialize" uCode */
__le32 voltage; /* signed, higher value is lower voltage */
- __le32 therm_r1[2]; /* signed, 1st for normal, 2nd for FAT channel*/
+ __le32 therm_r1[2]; /* signed, 1st for normal, 2nd for HT40 */
__le32 therm_r2[2]; /* signed */
__le32 therm_r3[2]; /* signed */
__le32 therm_r4[2]; /* signed */
#define RXON_RX_CHAIN_DRIVER_FORCE_MSK cpu_to_le16(0x1 << 0)
+#define RXON_RX_CHAIN_DRIVER_FORCE_POS (0)
#define RXON_RX_CHAIN_VALID_MSK cpu_to_le16(0x7 << 1)
#define RXON_RX_CHAIN_VALID_POS (1)
#define RXON_RX_CHAIN_FORCE_SEL_MSK cpu_to_le16(0x7 << 4)
#define RXON_FLG_HT_OPERATING_MODE_POS (23)
#define RXON_FLG_HT_PROT_MSK cpu_to_le32(0x1 << 23)
-#define RXON_FLG_FAT_PROT_MSK cpu_to_le32(0x2 << 23)
+#define RXON_FLG_HT40_PROT_MSK cpu_to_le32(0x2 << 23)
#define RXON_FLG_CHANNEL_MODE_POS (25)
#define RXON_FLG_CHANNEL_MODE_MSK cpu_to_le32(0x3 << 25)
-#define RXON_FLG_CHANNEL_MODE_PURE_40_MSK cpu_to_le32(0x1 << 25)
-#define RXON_FLG_CHANNEL_MODE_MIXED_MSK cpu_to_le32(0x2 << 25)
+
+/* channel mode */
+enum {
+ CHANNEL_MODE_LEGACY = 0,
+ CHANNEL_MODE_PURE_40 = 1,
+ CHANNEL_MODE_MIXED = 2,
+ CHANNEL_MODE_RESERVED = 3,
+};
+#define RXON_FLG_CHANNEL_MODE_LEGACY cpu_to_le32(CHANNEL_MODE_LEGACY << RXON_FLG_CHANNEL_MODE_POS)
+#define RXON_FLG_CHANNEL_MODE_PURE_40 cpu_to_le32(CHANNEL_MODE_PURE_40 << RXON_FLG_CHANNEL_MODE_POS)
+#define RXON_FLG_CHANNEL_MODE_MIXED cpu_to_le32(CHANNEL_MODE_MIXED << RXON_FLG_CHANNEL_MODE_POS)
+
/* CTS to self (if spec allows) flag */
#define RXON_FLG_SELF_CTS_EN cpu_to_le32(0x1<<30)
} __attribute__ ((packed));
#define IWL_CONN_MAX_LISTEN_INTERVAL 10
+#define IWL_MAX_UCODE_BEACON_INTERVAL 4 /* 4096 */
+#define IWL39_MAX_UCODE_BEACON_INTERVAL 1 /* 1024 */
/*
* REPLY_RXON_TIMING = 0x14 (command, has simple generic response)
struct iwl3945_power_per_rate power[IWL_MAX_RATES];
} __attribute__ ((packed));
-struct iwl_channel_switch_cmd {
+struct iwl4965_channel_switch_cmd {
u8 band;
u8 expect_beacon;
__le16 channel;
struct iwl4965_tx_power_db tx_power;
} __attribute__ ((packed));
+/**
+ * struct iwl5000_channel_switch_cmd
+ * @band: 0- 5.2GHz, 1- 2.4GHz
+ * @expect_beacon: 0- resume transmits after channel switch
+ * 1- wait for beacon to resume transmits
+ * @channel: new channel number
+ * @rxon_flags: Rx on flags
+ * @rxon_filter_flags: filtering parameters
+ * @switch_time: switch time in extended beacon format
+ * @reserved: reserved bytes
+ */
+struct iwl5000_channel_switch_cmd {
+ u8 band;
+ u8 expect_beacon;
+ __le16 channel;
+ __le32 rxon_flags;
+ __le32 rxon_filter_flags;
+ __le32 switch_time;
+ __le32 reserved[2][IWL_PWR_NUM_HT_OFDM_ENTRIES + IWL_PWR_CCK_ENTRIES];
+} __attribute__ ((packed));
+
+/**
+ * struct iwl6000_channel_switch_cmd
+ * @band: 0- 5.2GHz, 1- 2.4GHz
+ * @expect_beacon: 0- resume transmits after channel switch
+ * 1- wait for beacon to resume transmits
+ * @channel: new channel number
+ * @rxon_flags: Rx on flags
+ * @rxon_filter_flags: filtering parameters
+ * @switch_time: switch time in extended beacon format
+ * @reserved: reserved bytes
+ */
+struct iwl6000_channel_switch_cmd {
+ u8 band;
+ u8 expect_beacon;
+ __le16 channel;
+ __le32 rxon_flags;
+ __le32 rxon_filter_flags;
+ __le32 switch_time;
+ __le32 reserved[3][IWL_PWR_NUM_HT_OFDM_ENTRIES + IWL_PWR_CCK_ENTRIES];
+} __attribute__ ((packed));
+
/*
* CHANNEL_SWITCH_NOTIFICATION = 0x73 (notification only, not a command)
*/
#define STA_FLG_TX_RATE_MSK cpu_to_le32(1 << 2);
#define STA_FLG_PWR_SAVE_MSK cpu_to_le32(1 << 8);
-#define STA_FLG_PWR_SAVE_MSK cpu_to_le32(1 << 8);
#define STA_FLG_RTS_MIMO_PROT_MSK cpu_to_le32(1 << 17)
#define STA_FLG_AGG_MPDU_8US_MSK cpu_to_le32(1 << 18)
#define STA_FLG_MAX_AGG_SIZE_POS (19)
#define STA_FLG_MAX_AGG_SIZE_MSK cpu_to_le32(3 << 19)
-#define STA_FLG_FAT_EN_MSK cpu_to_le32(1 << 21)
+#define STA_FLG_HT40_EN_MSK cpu_to_le32(1 << 21)
#define STA_FLG_MIMO_DIS_MSK cpu_to_le32(1 << 22)
#define STA_FLG_AGG_MPDU_DENSITY_POS (23)
#define STA_FLG_AGG_MPDU_DENSITY_MSK cpu_to_le32(7 << 23)
#define STA_MODIFY_TX_RATE_MSK 0x04
#define STA_MODIFY_ADDBA_TID_MSK 0x08
#define STA_MODIFY_DELBA_TID_MSK 0x10
+#define STA_MODIFY_SLEEP_TX_COUNT_MSK 0x20
/* Receiver address (actually, Rx station's index into station table),
* combined with Traffic ID (QOS priority), in format used by Tx Scheduler */
* Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
__le16 add_immediate_ba_ssn;
- __le32 reserved2;
+ /*
+ * Number of packets OK to transmit to station even though
+ * it is asleep -- used to synchronise PS-poll and u-APSD
+ * responses while ucode keeps track of STA sleep state.
+ */
+ __le16 sleep_tx_count;
+
+ __le16 reserved2;
} __attribute__ ((packed));
/* 5000 */
* Set modify_mask bit STA_MODIFY_TID_DISABLE_TX to use this field. */
__le16 tid_disable_tx;
- __le16 reserved1;
+ __le16 rate_n_flags; /* 3945 only */
/* TID for which to add block-ack support.
* Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
* Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
__le16 add_immediate_ba_ssn;
- __le32 reserved2;
+ /*
+ * Number of packets OK to transmit to station even though
+ * it is asleep -- used to synchronise PS-poll and u-APSD
+ * responses while ucode keeps track of STA sleep state.
+ */
+ __le16 sleep_tx_count;
+
+ __le16 reserved2;
} __attribute__ ((packed));
#define RX_RES_PHY_FLAGS_MOD_CCK_MSK cpu_to_le16(1 << 1)
#define RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK cpu_to_le16(1 << 2)
#define RX_RES_PHY_FLAGS_NARROW_BAND_MSK cpu_to_le16(1 << 3)
-#define RX_RES_PHY_FLAGS_ANTENNA_MSK cpu_to_le16(0xf0)
+#define RX_RES_PHY_FLAGS_ANTENNA_MSK 0xf0
+#define RX_RES_PHY_FLAGS_ANTENNA_POS 4
#define RX_RES_STATUS_SEC_TYPE_MSK (0x7 << 8)
#define RX_RES_STATUS_SEC_TYPE_NONE (0x0 << 8)
TX_ABORT_REQUIRED_MSK = 0x80000000, /* bits 31:31 */
};
+static inline u32 iwl_tx_status_to_mac80211(u32 status)
+{
+ status &= TX_STATUS_MSK;
+
+ switch (status) {
+ case TX_STATUS_SUCCESS:
+ case TX_STATUS_DIRECT_DONE:
+ return IEEE80211_TX_STAT_ACK;
+ case TX_STATUS_FAIL_DEST_PS:
+ return IEEE80211_TX_STAT_TX_FILTERED;
+ default:
+ return 0;
+ }
+}
+
static inline bool iwl_is_tx_success(u32 status)
{
status &= TX_STATUS_MSK;
u8 start_rate_index[LINK_QUAL_AC_NUM];
} __attribute__ ((packed));
+#define LINK_QUAL_AGG_TIME_LIMIT_DEF (4000) /* 4 milliseconds */
+#define LINK_QUAL_AGG_TIME_LIMIT_MAX (65535)
+#define LINK_QUAL_AGG_TIME_LIMIT_MIN (0)
+
+#define LINK_QUAL_AGG_DISABLE_START_DEF (3)
+#define LINK_QUAL_AGG_DISABLE_START_MAX (255)
+#define LINK_QUAL_AGG_DISABLE_START_MIN (0)
+
+#define LINK_QUAL_AGG_FRAME_LIMIT_DEF (31)
+#define LINK_QUAL_AGG_FRAME_LIMIT_MAX (63)
+#define LINK_QUAL_AGG_FRAME_LIMIT_MIN (0)
+
/**
* struct iwl_link_qual_agg_params
*
* a) Use this same initial rate for first 3 entries.
* b) Find next lower available rate using same mode (SISO or MIMO),
* use for next 3 entries. If no lower rate available, switch to
- * legacy mode (no FAT channel, no MIMO, no short guard interval).
+ * legacy mode (no HT40 channel, no MIMO, no short guard interval).
* c) If using MIMO, set command's mimo_delimiter to number of entries
* using MIMO (3 or 6).
- * d) After trying 2 HT rates, switch to legacy mode (no FAT channel,
+ * d) After trying 2 HT rates, switch to legacy mode (no HT40 channel,
* no MIMO, no short guard interval), at the next lower bit rate
* (e.g. if second HT bit rate was 54, try 48 legacy), and follow
* legacy procedure for remaining table entries.
__le32 reserved2;
} __attribute__ ((packed));
+#define BT_COEX_DISABLE (0x0)
+#define BT_COEX_MODE_2W (0x1)
+#define BT_COEX_MODE_3W (0x2)
+#define BT_COEX_MODE_4W (0x3)
+
+#define BT_LEAD_TIME_MIN (0x0)
+#define BT_LEAD_TIME_DEF (0x1E)
+#define BT_LEAD_TIME_MAX (0xFF)
+
+#define BT_MAX_KILL_MIN (0x1)
+#define BT_MAX_KILL_DEF (0x5)
+#define BT_MAX_KILL_MAX (0xFF)
+
/*
* REPLY_BT_CONFIG = 0x9b (command, has simple generic response)
*
* PM allow:
* bit 0 - '0' Driver not allow power management
* '1' Driver allow PM (use rest of parameters)
+ *
* uCode send sleep notifications:
* bit 1 - '0' Don't send sleep notification
* '1' send sleep notification (SEND_PM_NOTIFICATION)
+ *
* Sleep over DTIM
* bit 2 - '0' PM have to walk up every DTIM
* '1' PM could sleep over DTIM till listen Interval.
+ *
* PCI power managed
* bit 3 - '0' (PCI_CFG_LINK_CTRL & 0x1)
* '1' !(PCI_CFG_LINK_CTRL & 0x1)
+ *
+ * Fast PD
+ * bit 4 - '1' Put radio to sleep when receiving frame for others
+ *
* Force sleep Modes
* bit 31/30- '00' use both mac/xtal sleeps
* '01' force Mac sleep
__le32 critical_temperature_R;
} __attribute__ ((packed));
+/* 1000, and 6x00 */
+struct iwl_ct_kill_throttling_config {
+ __le32 critical_temperature_exit;
+ __le32 reserved;
+ __le32 critical_temperature_enter;
+} __attribute__ ((packed));
+
/******************************************************************************
* (8)
* Scan Commands, Responses, Notifications:
__le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
} __attribute__ ((packed));
+/* set number of direct probes u8 type */
+#define IWL39_SCAN_PROBE_MASK(n) ((BIT(n) | (BIT(n) - BIT(1))))
+
struct iwl_scan_channel {
/*
* type is defined as:
__le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
} __attribute__ ((packed));
+/* set number of direct probes __le32 type */
+#define IWL_SCAN_PROBE_MASK(n) cpu_to_le32((BIT(n) | (BIT(n) - BIT(1))))
+
/**
* struct iwl_ssid_ie - directed scan network information element
*
- * Up to 4 of these may appear in REPLY_SCAN_CMD, selected by "type" field
- * in struct iwl_scan_channel; each channel may select different ssids from
- * among the 4 entries. SSID IEs get transmitted in reverse order of entry.
+ * Up to 20 of these may appear in REPLY_SCAN_CMD (Note: Only 4 are in
+ * 3945 SCAN api), selected by "type" bit field in struct iwl_scan_channel;
+ * each channel may select different ssids from among the 20 (4) entries.
+ * SSID IEs get transmitted in reverse order of entry.
*/
struct iwl_ssid_ie {
u8 id;
u8 ssid[32];
} __attribute__ ((packed));
-#define PROBE_OPTION_MAX_API1 0x4
-#define PROBE_OPTION_MAX 0x14
+#define PROBE_OPTION_MAX_3945 4
+#define PROBE_OPTION_MAX 20
#define TX_CMD_LIFE_TIME_INFINITE cpu_to_le32(0xFFFFFFFF)
#define IWL_GOOD_CRC_TH cpu_to_le16(1)
#define IWL_MAX_SCAN_SIZE 1024
+#define IWL_MAX_PROBE_REQUEST 200
/*
* REPLY_SCAN_CMD = 0x80 (command)
struct iwl3945_tx_cmd tx_cmd;
/* For directed active scans (set to all-0s otherwise) */
- struct iwl_ssid_ie direct_scan[PROBE_OPTION_MAX_API1];
+ struct iwl_ssid_ie direct_scan[PROBE_OPTION_MAX_3945];
/*
* Probe request frame, followed by channel list.
__le32 reserved2;
} __attribute__ ((packed));
-#define INTERFERENCE_DATA_AVAILABLE __constant_cpu_to_le32(1)
+#define INTERFERENCE_DATA_AVAILABLE cpu_to_le32(1)
struct statistics_rx_non_phy {
__le32 bogus_cts; /* CTS received when not expecting CTS */
struct statistics_rx_ht_phy ofdm_ht;
} __attribute__ ((packed));
+/**
+ * struct statistics_tx_power - current tx power
+ *
+ * @ant_a: current tx power on chain a in 1/2 dB step
+ * @ant_b: current tx power on chain b in 1/2 dB step
+ * @ant_c: current tx power on chain c in 1/2 dB step
+ */
+struct statistics_tx_power {
+ u8 ant_a;
+ u8 ant_b;
+ u8 ant_c;
+ u8 reserved;
+} __attribute__ ((packed));
+
struct statistics_tx_non_phy_agg {
__le32 ba_timeout;
__le32 ba_reschedule_frames;
__le32 underrun;
__le32 bt_prio_kill;
__le32 rx_ba_rsp_cnt;
- __le32 reserved2;
- __le32 reserved3;
} __attribute__ ((packed));
struct statistics_tx {
__le32 cts_timeout_collision;
__le32 ack_or_ba_timeout_collision;
struct statistics_tx_non_phy_agg agg;
+ struct statistics_tx_power tx_power;
+ __le32 reserved1;
} __attribute__ ((packed));
__le32 reserved3;
} __attribute__ ((packed));
+#define UCODE_STATISTICS_CLEAR_MSK (0x1 << 0)
+#define UCODE_STATISTICS_FREQUENCY_MSK (0x1 << 1)
+#define UCODE_STATISTICS_NARROW_BAND_MSK (0x1 << 2)
+
/*
* REPLY_STATISTICS_CMD = 0x9c,
* 3945 and 4965 identical.
* one channel that has just been scanned.
*/
#define STATISTICS_REPLY_FLG_BAND_24G_MSK cpu_to_le32(0x2)
-#define STATISTICS_REPLY_FLG_FAT_MODE_MSK cpu_to_le32(0x8)
+#define STATISTICS_REPLY_FLG_HT40_MODE_MSK cpu_to_le32(0x8)
struct iwl3945_notif_statistics {
__le32 flag;
* Lower values mean higher energy; this means making sure that the value
* in HD_MIN_ENERGY_CCK_DET_INDEX is at or *above* "Max cck energy".
*
- * Driver should set the following entries to fixed values:
- *
- * HD_MIN_ENERGY_OFDM_DET_INDEX 100
- * HD_BARKER_CORR_TH_ADD_MIN_INDEX 190
- * HD_BARKER_CORR_TH_ADD_MIN_MRC_INDEX 390
- * HD_OFDM_ENERGY_TH_IN_INDEX 62
*/
/*
} __attribute__ ((packed));
/*
- * Coexistence WIFI/WIMAX Command
- * COEX_PRIORITY_TABLE_CMD = 0x5a
- *
+ * station priority table entries
+ * also used as potential "events" value for both
+ * COEX_MEDIUM_NOTIFICATION and COEX_EVENT_CMD
*/
+
+/*
+ * COEX events entry flag masks
+ * RP - Requested Priority
+ * WP - Win Medium Priority: priority assigned when the contention has been won
+ */
+#define COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG (0x1)
+#define COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG (0x2)
+#define COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG (0x4)
+
+#define COEX_CU_UNASSOC_IDLE_RP 4
+#define COEX_CU_UNASSOC_MANUAL_SCAN_RP 4
+#define COEX_CU_UNASSOC_AUTO_SCAN_RP 4
+#define COEX_CU_CALIBRATION_RP 4
+#define COEX_CU_PERIODIC_CALIBRATION_RP 4
+#define COEX_CU_CONNECTION_ESTAB_RP 4
+#define COEX_CU_ASSOCIATED_IDLE_RP 4
+#define COEX_CU_ASSOC_MANUAL_SCAN_RP 4
+#define COEX_CU_ASSOC_AUTO_SCAN_RP 4
+#define COEX_CU_ASSOC_ACTIVE_LEVEL_RP 4
+#define COEX_CU_RF_ON_RP 6
+#define COEX_CU_RF_OFF_RP 4
+#define COEX_CU_STAND_ALONE_DEBUG_RP 6
+#define COEX_CU_IPAN_ASSOC_LEVEL_RP 4
+#define COEX_CU_RSRVD1_RP 4
+#define COEX_CU_RSRVD2_RP 4
+
+#define COEX_CU_UNASSOC_IDLE_WP 3
+#define COEX_CU_UNASSOC_MANUAL_SCAN_WP 3
+#define COEX_CU_UNASSOC_AUTO_SCAN_WP 3
+#define COEX_CU_CALIBRATION_WP 3
+#define COEX_CU_PERIODIC_CALIBRATION_WP 3
+#define COEX_CU_CONNECTION_ESTAB_WP 3
+#define COEX_CU_ASSOCIATED_IDLE_WP 3
+#define COEX_CU_ASSOC_MANUAL_SCAN_WP 3
+#define COEX_CU_ASSOC_AUTO_SCAN_WP 3
+#define COEX_CU_ASSOC_ACTIVE_LEVEL_WP 3
+#define COEX_CU_RF_ON_WP 3
+#define COEX_CU_RF_OFF_WP 3
+#define COEX_CU_STAND_ALONE_DEBUG_WP 6
+#define COEX_CU_IPAN_ASSOC_LEVEL_WP 3
+#define COEX_CU_RSRVD1_WP 3
+#define COEX_CU_RSRVD2_WP 3
+
+#define COEX_UNASSOC_IDLE_FLAGS 0
+#define COEX_UNASSOC_MANUAL_SCAN_FLAGS \
+ (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
+ COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
+#define COEX_UNASSOC_AUTO_SCAN_FLAGS \
+ (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
+ COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
+#define COEX_CALIBRATION_FLAGS \
+ (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
+ COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
+#define COEX_PERIODIC_CALIBRATION_FLAGS 0
+/*
+ * COEX_CONNECTION_ESTAB:
+ * we need DELAY_MEDIUM_FREE_NTFY to let WiMAX disconnect from network.
+ */
+#define COEX_CONNECTION_ESTAB_FLAGS \
+ (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
+ COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG | \
+ COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG)
+#define COEX_ASSOCIATED_IDLE_FLAGS 0
+#define COEX_ASSOC_MANUAL_SCAN_FLAGS \
+ (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
+ COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
+#define COEX_ASSOC_AUTO_SCAN_FLAGS \
+ (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
+ COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
+#define COEX_ASSOC_ACTIVE_LEVEL_FLAGS 0
+#define COEX_RF_ON_FLAGS 0
+#define COEX_RF_OFF_FLAGS 0
+#define COEX_STAND_ALONE_DEBUG_FLAGS \
+ (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
+ COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
+#define COEX_IPAN_ASSOC_LEVEL_FLAGS \
+ (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
+ COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG | \
+ COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG)
+#define COEX_RSRVD1_FLAGS 0
+#define COEX_RSRVD2_FLAGS 0
+/*
+ * COEX_CU_RF_ON is the event wrapping all radio ownership.
+ * We need DELAY_MEDIUM_FREE_NTFY to let WiMAX disconnect from network.
+ */
+#define COEX_CU_RF_ON_FLAGS \
+ (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
+ COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG | \
+ COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG)
+
+
enum {
+ /* un-association part */
COEX_UNASSOC_IDLE = 0,
COEX_UNASSOC_MANUAL_SCAN = 1,
COEX_UNASSOC_AUTO_SCAN = 2,
+ /* calibration */
COEX_CALIBRATION = 3,
COEX_PERIODIC_CALIBRATION = 4,
+ /* connection */
COEX_CONNECTION_ESTAB = 5,
+ /* association part */
COEX_ASSOCIATED_IDLE = 6,
COEX_ASSOC_MANUAL_SCAN = 7,
COEX_ASSOC_AUTO_SCAN = 8,
COEX_ASSOC_ACTIVE_LEVEL = 9,
+ /* RF ON/OFF */
COEX_RF_ON = 10,
COEX_RF_OFF = 11,
COEX_STAND_ALONE_DEBUG = 12,
+ /* IPAN */
COEX_IPAN_ASSOC_LEVEL = 13,
+ /* reserved */
COEX_RSRVD1 = 14,
COEX_RSRVD2 = 15,
COEX_NUM_OF_EVENTS = 16
};
+/*
+ * Coexistence WIFI/WIMAX Command
+ * COEX_PRIORITY_TABLE_CMD = 0x5a
+ *
+ */
struct iwl_wimax_coex_event_entry {
u8 request_prio;
u8 win_medium_prio;
struct iwl_wimax_coex_event_entry sta_prio[COEX_NUM_OF_EVENTS];
} __attribute__ ((packed));
+/*
+ * Coexistence MEDIUM NOTIFICATION
+ * COEX_MEDIUM_NOTIFICATION = 0x5b
+ *
+ * notification from uCode to host to indicate medium changes
+ *
+ */
+/*
+ * status field
+ * bit 0 - 2: medium status
+ * bit 3: medium change indication
+ * bit 4 - 31: reserved
+ */
+/* status option values, (0 - 2 bits) */
+#define COEX_MEDIUM_BUSY (0x0) /* radio belongs to WiMAX */
+#define COEX_MEDIUM_ACTIVE (0x1) /* radio belongs to WiFi */
+#define COEX_MEDIUM_PRE_RELEASE (0x2) /* received radio release */
+#define COEX_MEDIUM_MSK (0x7)
+
+/* send notification status (1 bit) */
+#define COEX_MEDIUM_CHANGED (0x8)
+#define COEX_MEDIUM_CHANGED_MSK (0x8)
+#define COEX_MEDIUM_SHIFT (3)
+
+struct iwl_coex_medium_notification {
+ __le32 status;
+ __le32 events;
+} __attribute__ ((packed));
+
+/*
+ * Coexistence EVENT Command
+ * COEX_EVENT_CMD = 0x5c
+ *
+ * send from host to uCode for coex event request.
+ */
+/* flags options */
+#define COEX_EVENT_REQUEST_MSK (0x1)
+
+struct iwl_coex_event_cmd {
+ u8 flags;
+ u8 event;
+ __le16 reserved;
+} __attribute__ ((packed));
+
+struct iwl_coex_event_resp {
+ __le32 status;
+} __attribute__ ((packed));
+
+
/******************************************************************************
* (13)
* Union of all expected notifications/responses:
*****************************************************************************/
struct iwl_rx_packet {
- __le32 len;
+ /*
+ * The first 4 bytes of the RX frame header contain both the RX frame
+ * size and some flags.
+ * Bit fields:
+ * 31: flag flush RB request
+ * 30: flag ignore TC (terminal counter) request
+ * 29: flag fast IRQ request
+ * 28-14: Reserved
+ * 13-00: RX frame size
+ */
+ __le32 len_n_flags;
struct iwl_cmd_header hdr;
union {
struct iwl3945_rx_frame rx_frame;
struct iwl_notif_statistics stats;
struct iwl_compressed_ba_resp compressed_ba;
struct iwl_missed_beacon_notif missed_beacon;
+ struct iwl_coex_medium_notification coex_medium_notif;
+ struct iwl_coex_event_resp coex_event;
__le32 status;
u8 raw[0];
} u;
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff