# Wireless LAN device configuration
#
-menu "Wireless LAN"
+menuconfig WLAN
+ bool "Wireless LAN"
depends on !S390
-
-config WLAN_PRE80211
- bool "Wireless LAN (pre-802.11)"
- depends on NETDEVICES
- ---help---
- Say Y if you have any pre-802.11 wireless LAN hardware.
-
- This option does not affect the kernel build, it only
- lets you choose drivers.
-
-config STRIP
- tristate "STRIP (Metricom starmode radio IP)"
- depends on INET && WLAN_PRE80211
- select WIRELESS_EXT
- ---help---
- Say Y if you have a Metricom radio and intend to use Starmode Radio
- IP. STRIP is a radio protocol developed for the MosquitoNet project
- (on the WWW at <http://mosquitonet.stanford.edu/>) to send Internet
- traffic using Metricom radios. Metricom radios are small, battery
- powered, 100kbit/sec packet radio transceivers, about the size and
- weight of a cellular telephone. (You may also have heard them called
- "Metricom modems" but we avoid the term "modem" because it misleads
- many people into thinking that you can plug a Metricom modem into a
- phone line and use it as a modem.)
-
- You can use STRIP on any Linux machine with a serial port, although
- it is obviously most useful for people with laptop computers. If you
- think you might get a Metricom radio in the future, there is no harm
- in saying Y to STRIP now, except that it makes the kernel a bit
- bigger.
-
- To compile this as a module, choose M here: the module will be
- called strip.
-
-config ARLAN
- tristate "Aironet Arlan 655 & IC2200 DS support"
- depends on ISA && !64BIT && WLAN_PRE80211
- select WIRELESS_EXT
+ select WIRELESS
+ default y
---help---
- Aironet makes Arlan, a class of wireless LAN adapters. These use the
- www.Telxon.com chip, which is also used on several similar cards.
- This driver is tested on the 655 and IC2200 series cards. Look at
- <http://www.ylenurme.ee/~elmer/655/> for the latest information.
-
- The driver is built as two modules, arlan and arlan-proc. The latter
- is the /proc interface and is not needed most of time.
-
- On some computers the card ends up in non-valid state after some
- time. Use a ping-reset script to clear it.
-
-config WAVELAN
- tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support"
- depends on ISA && WLAN_PRE80211
- select WIRELESS_EXT
- ---help---
- The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is
- a Radio LAN (wireless Ethernet-like Local Area Network) using the
- radio frequencies 900 MHz and 2.4 GHz.
-
- This driver support the ISA version of the WaveLAN card. A separate
- driver for the PCMCIA (PC-card) hardware is available in David
- Hinds' pcmcia-cs package (see the file <file:Documentation/Changes>
- for location).
-
- If you want to use an ISA WaveLAN card under Linux, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Some more specific
- information is contained in
- <file:Documentation/networking/wavelan.txt> and in the source code
- <file:drivers/net/wavelan.p.h>.
-
- You will also need the wireless tools package available from
- <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
- Please read the man pages contained therein.
-
- To compile this driver as a module, choose M here: the module will be
- called wavelan.
+ This section contains all the pre 802.11 and 802.11 wireless
+ device drivers. For a complete list of drivers and documentation
+ on them refer to the wireless wiki:
-config PCMCIA_WAVELAN
- tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support"
- depends on PCMCIA && WLAN_PRE80211
- select WIRELESS_EXT
- help
- Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA
- (PC-card) wireless Ethernet networking card to your computer. This
- driver is for the non-IEEE-802.11 Wavelan cards.
-
- To compile this driver as a module, choose M here: the module will be
- called wavelan_cs. If unsure, say N.
-
-config PCMCIA_NETWAVE
- tristate "Xircom Netwave AirSurfer Pcmcia wireless support"
- depends on PCMCIA && WLAN_PRE80211
- select WIRELESS_EXT
- help
- Say Y here if you intend to attach this type of PCMCIA (PC-card)
- wireless Ethernet networking card to your computer.
+ http://wireless.kernel.org/en/users/Drivers
- To compile this driver as a module, choose M here: the module will be
- called netwave_cs. If unsure, say N.
-
-
-config WLAN_80211
- bool "Wireless LAN (IEEE 802.11)"
- depends on NETDEVICES
- ---help---
- Say Y if you have any 802.11 wireless LAN hardware.
-
- This option does not affect the kernel build, it only
- lets you choose drivers.
+if WLAN
config PCMCIA_RAYCS
- tristate "Aviator/Raytheon 2.4MHz wireless support"
- depends on PCMCIA && WLAN_80211
+ tristate "Aviator/Raytheon 2.4GHz wireless support"
+ depends on PCMCIA
select WIRELESS_EXT
+ select WEXT_SPY
+ select WEXT_PRIV
---help---
Say Y here if you intend to attach an Aviator/Raytheon PCMCIA
(PC-card) wireless Ethernet networking card to your computer.
To compile this driver as a module, choose M here: the module will be
called ray_cs. If unsure, say N.
-config IPW2100
- tristate "Intel PRO/Wireless 2100 Network Connection"
- depends on PCI && WLAN_80211
- select WIRELESS_EXT
+config LIBERTAS_THINFIRM
+ tristate "Marvell 8xxx Libertas WLAN driver support with thin firmware"
+ depends on MAC80211
select FW_LOADER
- select IEEE80211
---help---
- A driver for the Intel PRO/Wireless 2100 Network
- Connection 802.11b wireless network adapter.
-
- See <file:Documentation/networking/README.ipw2100> for information on
- the capabilities currently enabled in this driver and for tips
- for debugging issues and problems.
-
- In order to use this driver, you will need a firmware image for it.
- You can obtain the firmware from
- <http://ipw2100.sf.net/>. Once you have the firmware image, you
- will need to place it in /lib/firmware.
-
- You will also very likely need the Wireless Tools in order to
- configure your card:
-
- <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
-
- If you want to compile the driver as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want),
- say M here and read <file:Documentation/kbuild/modules.txt>.
- The module will be called ipw2100.ko.
-
-config IPW2100_MONITOR
- bool "Enable promiscuous mode"
- depends on IPW2100
- ---help---
- Enables promiscuous/monitor mode support for the ipw2100 driver.
- With this feature compiled into the driver, you can switch to
- promiscuous mode via the Wireless Tool's Monitor mode. While in this
- mode, no packets can be sent.
-
-config IPW2100_DEBUG
- bool "Enable full debugging output in IPW2100 module."
- depends on IPW2100
- ---help---
- This option will enable debug tracing output for the IPW2100.
-
- This will result in the kernel module being ~60k larger. You can
- control which debug output is sent to the kernel log by setting the
- value in
-
- /sys/bus/pci/drivers/ipw2100/debug_level
-
- This entry will only exist if this option is enabled.
+ A library for Marvell Libertas 8xxx devices using thinfirm.
- If you are not trying to debug or develop the IPW2100 driver, you
- most likely want to say N here.
-
-config IPW2200
- tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection"
- depends on PCI && WLAN_80211
- select WIRELESS_EXT
- select FW_LOADER
- select IEEE80211
+config LIBERTAS_THINFIRM_USB
+ tristate "Marvell Libertas 8388 USB 802.11b/g cards with thin firmware"
+ depends on LIBERTAS_THINFIRM && USB
---help---
- A driver for the Intel PRO/Wireless 2200BG and 2915ABG Network
- Connection adapters.
-
- See <file:Documentation/networking/README.ipw2200> for
- information on the capabilities currently enabled in this
- driver and for tips for debugging issues and problems.
-
- In order to use this driver, you will need a firmware image for it.
- You can obtain the firmware from
- <http://ipw2200.sf.net/>. See the above referenced README.ipw2200
- for information on where to install the firmware images.
-
- You will also very likely need the Wireless Tools in order to
- configure your card:
-
- <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
-
- If you want to compile the driver as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want),
- say M here and read <file:Documentation/kbuild/modules.txt>.
- The module will be called ipw2200.ko.
-
-config IPW2200_MONITOR
- bool "Enable promiscuous mode"
- depends on IPW2200
- ---help---
- Enables promiscuous/monitor mode support for the ipw2200 driver.
- With this feature compiled into the driver, you can switch to
- promiscuous mode via the Wireless Tool's Monitor mode. While in this
- mode, no packets can be sent.
-
-config IPW2200_RADIOTAP
- bool "Enable radiotap format 802.11 raw packet support"
- depends on IPW2200_MONITOR
-
-config IPW2200_PROMISCUOUS
- bool "Enable creation of a RF radiotap promiscuous interface"
- depends on IPW2200_MONITOR
- select IPW2200_RADIOTAP
- ---help---
- Enables the creation of a second interface prefixed 'rtap'.
- This second interface will provide every received in radiotap
- format.
-
- This is useful for performing wireless network analysis while
- maintaining an active association.
-
- Example usage:
-
- % modprobe ipw2200 rtap_iface=1
- % ifconfig rtap0 up
- % tethereal -i rtap0
-
- If you do not specify 'rtap_iface=1' as a module parameter then
- the rtap interface will not be created and you will need to turn
- it on via sysfs:
-
- % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
-
-config IPW2200_QOS
- bool "Enable QoS support"
- depends on IPW2200 && EXPERIMENTAL
-
-config IPW2200_DEBUG
- bool "Enable full debugging output in IPW2200 module."
- depends on IPW2200
- ---help---
- This option will enable low level debug tracing output for IPW2200.
-
- Note, normal debug code is already compiled in. This low level
- debug option enables debug on hot paths (e.g Tx, Rx, ISR) and
- will result in the kernel module being ~70 larger. Most users
- will typically not need this high verbosity debug information.
-
- If you are not sure, say N here.
-
-config LIBERTAS
- tristate "Marvell 8xxx Libertas WLAN driver support"
- depends on WLAN_80211
- select IEEE80211
- select FW_LOADER
- ---help---
- A library for Marvell Libertas 8xxx devices.
-
-config LIBERTAS_USB
- tristate "Marvell Libertas 8388 USB 802.11b/g cards"
- depends on LIBERTAS && USB
- ---help---
- A driver for Marvell Libertas 8388 USB devices.
-
-config LIBERTAS_DEBUG
- bool "Enable full debugging output in the Libertas module."
- depends on LIBERTAS
- ---help---
- Debugging support.
+ A driver for Marvell Libertas 8388 USB devices using thinfirm.
config AIRO
tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards"
- depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN)
+ depends on ISA_DMA_API && (PCI || BROKEN)
select WIRELESS_EXT
select CRYPTO
+ select WEXT_SPY
+ select WEXT_PRIV
---help---
This is the standard Linux driver to support Cisco/Aironet ISA and
PCI 802.11 wireless cards.
The driver can be compiled as a module and will be named "airo".
-config HERMES
- tristate "Hermes chipset 802.11b support (Orinoco/Prism2/Symbol)"
- depends on (PPC_PMAC || PCI || PCMCIA) && WLAN_80211
- select WIRELESS_EXT
- ---help---
- A driver for 802.11b wireless cards based on the "Hermes" or
- Intersil HFA384x (Prism 2) MAC controller. This includes the vast
- majority of the PCMCIA 802.11b cards (which are nearly all rebadges)
- - except for the Cisco/Aironet cards. Cards supported include the
- Apple Airport (not a PCMCIA card), WavelanIEEE/Orinoco,
- Cabletron/EnteraSys Roamabout, ELSA AirLancer, MELCO Buffalo, Avaya,
- IBM High Rate Wireless, Farralon Syyline, Samsung MagicLAN, Netgear
- MA401, LinkSys WPC-11, D-Link DWL-650, 3Com AirConnect, Intel
- PRO/Wireless, and Symbol Spectrum24 High Rate amongst others.
-
- This option includes the guts of the driver, but in order to
- actually use a card you will also need to enable support for PCMCIA
- Hermes cards, PLX9052 based PCI adaptors or the Apple Airport below.
-
- You will also very likely also need the Wireless Tools in order to
- configure your card and that /etc/pcmcia/wireless.opts works :
- <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>
-
-config APPLE_AIRPORT
- tristate "Apple Airport support (built-in)"
- depends on PPC_PMAC && HERMES
- help
- Say Y here to support the Airport 802.11b wireless Ethernet hardware
- built into the Macintosh iBook and other recent PowerPC-based
- Macintosh machines. This is essentially a Lucent Orinoco card with
- a non-standard interface.
-
- This driver does not support the Airport Extreme (802.11b/g). Use
- the BCM43xx driver for Airport Extreme cards.
-
-config PLX_HERMES
- tristate "Hermes in PLX9052 based PCI adaptor support (Netgear MA301 etc.)"
- depends on PCI && HERMES
- help
- Enable support for PCMCIA cards supported by the "Hermes" (aka
- orinoco) driver when used in PLX9052 based PCI adaptors. These
- adaptors are not a full PCMCIA controller but act as a more limited
- PCI <-> PCMCIA bridge. Several vendors sell such adaptors so that
- 802.11b PCMCIA cards can be used in desktop machines. The Netgear
- MA301 is such an adaptor.
-
-config TMD_HERMES
- tristate "Hermes in TMD7160 based PCI adaptor support"
- depends on PCI && HERMES
- help
- Enable support for PCMCIA cards supported by the "Hermes" (aka
- orinoco) driver when used in TMD7160 based PCI adaptors. These
- adaptors are not a full PCMCIA controller but act as a more limited
- PCI <-> PCMCIA bridge. Several vendors sell such adaptors so that
- 802.11b PCMCIA cards can be used in desktop machines.
-
-config NORTEL_HERMES
- tristate "Nortel emobility PCI adaptor support"
- depends on PCI && HERMES
- help
- Enable support for PCMCIA cards supported by the "Hermes" (aka
- orinoco) driver when used in Nortel emobility PCI adaptors. These
- adaptors are not full PCMCIA controllers, but act as a more limited
- PCI <-> PCMCIA bridge.
-
-config PCI_HERMES
- tristate "Prism 2.5 PCI 802.11b adaptor support"
- depends on PCI && HERMES
- help
- Enable support for PCI and mini-PCI 802.11b wireless NICs based on
- the Prism 2.5 chipset. These are true PCI cards, not the 802.11b
- PCMCIA cards bundled with PCI<->PCMCIA adaptors which are also
- common. Some of the built-in wireless adaptors in laptops are of
- this variety.
-
config ATMEL
tristate "Atmel at76c50x chipset 802.11b support"
- depends on (PCI || PCMCIA) && WLAN_80211
+ depends on (PCI || PCMCIA)
select WIRELESS_EXT
+ select WEXT_PRIV
select FW_LOADER
select CRC32
---help---
A driver 802.11b wireless cards based on the Atmel fast-vnet
- chips. This driver supports standard Linux wireless extensions.
-
+ chips. This driver supports standard Linux wireless extensions.
+
Many cards based on this chipset do not have flash memory
- and need their firmware loaded at start-up. If yours is
+ and need their firmware loaded at start-up. If yours is
one of these, you will need to provide a firmware image
to be loaded into the card by the driver. The Atmel
firmware package can be downloaded from
Enable support for PCI and mini-PCI cards containing the
Atmel at76c506 chip.
-config PCMCIA_HERMES
- tristate "Hermes PCMCIA card support"
- depends on PCMCIA && HERMES
- ---help---
- A driver for "Hermes" chipset based PCMCIA wireless adaptors, such
- as the Lucent WavelanIEEE/Orinoco cards and their OEM (Cabletron/
- EnteraSys RoamAbout 802.11, ELSA Airlancer, Melco Buffalo and
- others). It should also be usable on various Prism II based cards
- such as the Linksys, D-Link and Farallon Skyline. It should also
- work on Symbol cards such as the 3Com AirConnect and Ericsson WLAN.
-
- To use your PC-cards, you will need supporting software from David
- Hinds' pcmcia-cs package (see the file <file:Documentation/Changes>
- for location). You also want to check out the PCMCIA-HOWTO,
- available from <http://www.tldp.org/docs.html#howto>.
-
- You will also very likely also need the Wireless Tools in order to
- configure your card and that /etc/pcmcia/wireless.opts works:
- <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
-
-config PCMCIA_SPECTRUM
- tristate "Symbol Spectrum24 Trilogy PCMCIA card support"
- depends on PCMCIA && HERMES
+config PCMCIA_ATMEL
+ tristate "Atmel at76c502/at76c504 PCMCIA cards"
+ depends on ATMEL && PCMCIA
+ select WIRELESS_EXT
select FW_LOADER
+ select CRC32
---help---
+ Enable support for PCMCIA cards containing the
+ Atmel at76c502 and at76c504 chips.
- This is a driver for 802.11b cards using RAM-loadable Symbol
- firmware, such as Symbol Wireless Networker LA4100, CompactFlash
- cards by Socket Communications and Intel PRO/Wireless 2011B.
-
- This driver requires firmware download on startup. Utilities
- for downloading Symbol firmware are available at
- <http://sourceforge.net/projects/orinoco/>
+config AT76C50X_USB
+ tristate "Atmel at76c503/at76c505/at76c505a USB cards"
+ depends on MAC80211 && USB
+ select FW_LOADER
+ ---help---
+ Enable support for USB Wireless devices using Atmel at76c503,
+ at76c505 or at76c505a chips.
config AIRO_CS
tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards"
- depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211
+ depends on PCMCIA && (BROKEN || !M32R)
select WIRELESS_EXT
+ select WEXT_SPY
select CRYPTO
select CRYPTO_AES
---help---
and Cisco proprietary API, so both the Linux Wireless Tools and the
Cisco Linux utilities can be used to configure the card.
- To use your PC-cards, you will need supporting software from David
- Hinds' pcmcia-cs package (see the file <file:Documentation/Changes>
- for location). You also want to check out the PCMCIA-HOWTO,
- available from <http://www.tldp.org/docs.html#howto>.
-
-config PCMCIA_ATMEL
- tristate "Atmel at76c502/at76c504 PCMCIA cards"
- depends on ATMEL && PCMCIA
- select WIRELESS_EXT
- select FW_LOADER
- select CRC32
- ---help---
- Enable support for PCMCIA cards containing the
- Atmel at76c502 and at76c504 chips.
-
config PCMCIA_WL3501
- tristate "Planet WL3501 PCMCIA cards"
- depends on EXPERIMENTAL && PCMCIA && WLAN_80211
- select WIRELESS_EXT
- ---help---
- A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
- It has basic support for Linux wireless extensions and initial
- micro support for ethtool.
+ tristate "Planet WL3501 PCMCIA cards"
+ depends on EXPERIMENTAL && PCMCIA
+ select WIRELESS_EXT
+ select WEXT_SPY
+ help
+ A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
+ It has basic support for Linux wireless extensions and initial
+ micro support for ethtool.
config PRISM54
- tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus'
- depends on PCI && EXPERIMENTAL && WLAN_80211
+ tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus (DEPRECATED)'
+ depends on PCI && EXPERIMENTAL
select WIRELESS_EXT
+ select WEXT_SPY
+ select WEXT_PRIV
select FW_LOADER
---help---
- Enable PCI and Cardbus support for the following chipset based cards:
-
- ISL3880 - Prism GT 802.11 b/g
- ISL3877 - Prism Indigo 802.11 a
- ISL3890 - Prism Duette 802.11 a/b/g
-
- For a complete list of supported cards visit <http://prism54.org>.
- Here is the latest confirmed list of supported cards:
-
- 3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 (version 1)
- Allnet ALL0271 PCI Card
- Compex WL54G Cardbus Card
- Corega CG-WLCB54GT Cardbus Card
- D-Link Air Plus Xtreme G A1 Cardbus Card aka DWL-g650
- I-O Data WN-G54/CB Cardbus Card
- Kobishi XG-300 aka Z-Com Cardbus Card
- Netgear WG511 Cardbus Card
- Ovislink WL-5400PCI PCI Card
- Peabird WLG-PCI PCI Card
- Sitecom WL-100i Cardbus Card
- Sitecom WL-110i PCI Card
- SMC2802W - EZ Connect g 2.4GHz 54 Mbps Wireless PCI Card
- SMC2835W - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
- SMC2835W-V2 - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
- Z-Com XG-900 PCI Card
- Zyxel G-100 Cardbus Card
-
- If you enable this you will need a firmware file as well.
- You will need to copy this to /usr/lib/hotplug/firmware/isl3890.
- You can get this non-GPL'd firmware file from the Prism54 project page:
- <http://prism54.org>
- You will also need the /etc/hotplug/firmware.agent script from
- a current hotplug package.
-
- Note: You need a motherboard with DMA support to use any of these cards
-
- If you want to compile the driver as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want),
- say M here and read <file:Documentation/kbuild/modules.txt>.
- The module will be called prism54.ko.
+ This enables support for FullMAC PCI/Cardbus prism54 devices. This
+ driver is now deprecated in favor for the SoftMAC driver, p54pci.
+ p54pci supports FullMAC PCI/Cardbus devices as well. For details on
+ the scheduled removal of this driver on the kernel see the feature
+ removal schedule:
+
+ Documentation/feature-removal-schedule.txt
+
+ For more information refer to the p54 wiki:
+
+ http://wireless.kernel.org/en/users/Drivers/p54
+
+ Note: You need a motherboard with DMA support to use any of these cards
+
+ When built as module you get the module prism54
config USB_ZD1201
tristate "USB ZD1201 based Wireless device support"
- depends on USB && WLAN_80211
+ depends on USB
select WIRELESS_EXT
+ select WEXT_PRIV
select FW_LOADER
---help---
Say Y if you want to use wireless LAN adapters based on the ZyDAS
To compile this driver as a module, choose M here: the
module will be called zd1201.
+config USB_NET_RNDIS_WLAN
+ tristate "Wireless RNDIS USB support"
+ depends on USB && EXPERIMENTAL
+ depends on CFG80211
+ select USB_USBNET
+ select USB_NET_CDCETHER
+ select USB_NET_RNDIS_HOST
+ ---help---
+ This is a driver for wireless RNDIS devices.
+ These are USB based adapters found in devices such as:
+
+ Buffalo WLI-U2-KG125S
+ U.S. Robotics USR5421
+ Belkin F5D7051
+ Linksys WUSB54GSv2
+ Linksys WUSB54GSC
+ Asus WL169gE
+ Eminent EM4045
+ BT Voyager 1055
+ Linksys WUSB54GSv1
+ U.S. Robotics USR5420
+ BUFFALO WLI-USB-G54
+
+ All of these devices are based on Broadcom 4320 chip which is the
+ only wireless RNDIS chip known to date.
+
+ If you choose to build a module, it'll be called rndis_wlan.
+
+config RTL8180
+ tristate "Realtek 8180/8185 PCI support"
+ depends on MAC80211 && PCI && EXPERIMENTAL
+ select EEPROM_93CX6
+ ---help---
+ This is a driver for RTL8180 and RTL8185 based cards.
+ These are PCI based chips found in cards such as:
+
+ (RTL8185 802.11g)
+ A-Link WL54PC
+
+ (RTL8180 802.11b)
+ Belkin F5D6020 v3
+ Belkin F5D6020 v3
+ Dlink DWL-610
+ Dlink DWL-510
+ Netgear MA521
+ Level-One WPC-0101
+ Acer Aspire 1357 LMi
+ VCTnet PC-11B1
+ Ovislink AirLive WL-1120PCM
+ Mentor WL-PCI
+ Linksys WPC11 v4
+ TrendNET TEW-288PI
+ D-Link DWL-520 Rev D
+ Repotec RP-WP7126
+ TP-Link TL-WN250/251
+ Zonet ZEW1000
+ Longshine LCS-8031-R
+ HomeLine HLW-PCC200
+ GigaFast WF721-AEX
+ Planet WL-3553
+ Encore ENLWI-PCI1-NT
+ TrendNET TEW-266PC
+ Gigabyte GN-WLMR101
+ Siemens-fujitsu Amilo D1840W
+ Edimax EW-7126
+ PheeNet WL-11PCIR
+ Tonze PC-2100T
+ Planet WL-8303
+ Dlink DWL-650 v M1
+ Edimax EW-7106
+ Q-Tec 770WC
+ Topcom Skyr@cer 4011b
+ Roper FreeLan 802.11b (edition 2004)
+ Wistron Neweb Corp CB-200B
+ Pentagram HorNET
+ QTec 775WC
+ TwinMOS Booming B Series
+ Micronet SP906BB
+ Sweex LC700010
+ Surecom EP-9428
+ Safecom SWLCR-1100
+
+ Thanks to Realtek for their support!
+
config RTL8187
- tristate "Realtek 8187 USB support"
- depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL
+ tristate "Realtek 8187 and 8187B USB support"
+ depends on MAC80211 && USB
select EEPROM_93CX6
---help---
- This is a driver for RTL8187 based cards.
- These are USB based chips found in cards such as:
+ This is a driver for RTL8187 and RTL8187B based cards.
+ These are USB based chips found in devices such as:
Netgear WG111v2
+ Level 1 WNC-0301USB
+ Micronet SP907GK V5
+ Encore ENUWI-G2
+ Trendnet TEW-424UB
+ ASUS P5B Deluxe/P5K Premium motherboards
+ Toshiba Satellite Pro series of laptops
+ Asus Wireless Link
+ Linksys WUSB54GC-EU v2
+ (v1 = rt73usb; v3 is rt2070-based,
+ use staging/rt3070 or try rt2800usb)
Thanks to Realtek for their support!
+# If possible, automatically enable LEDs for RTL8187.
+
+config RTL8187_LEDS
+ bool
+ depends on RTL8187 && MAC80211_LEDS && (LEDS_CLASS = y || LEDS_CLASS = RTL8187)
+ default y
+
config ADM8211
tristate "ADMtek ADM8211 support"
- depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
+ depends on MAC80211 && PCI && EXPERIMENTAL
select CRC32
select EEPROM_93CX6
---help---
Thanks to Infineon-ADMtek for their support of this driver.
+config MAC80211_HWSIM
+ tristate "Simulated radio testing tool for mac80211"
+ depends on MAC80211
+ ---help---
+ This driver is a developer testing tool that can be used to test
+ IEEE 802.11 networking stack (mac80211) functionality. This is not
+ needed for normal wireless LAN usage and is only for testing. See
+ Documentation/networking/mac80211_hwsim for more information on how
+ to use this tool.
+
+ To compile this driver as a module, choose M here: the module will be
+ called mac80211_hwsim. If unsure, say N.
+
+config MWL8K
+ tristate "Marvell 88W8xxx PCI/PCIe Wireless support"
+ depends on MAC80211 && PCI && EXPERIMENTAL
+ ---help---
+ This driver supports Marvell TOPDOG 802.11 wireless cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called mwl8k. If unsure, say N.
+
+source "drivers/net/wireless/ath/Kconfig"
+source "drivers/net/wireless/b43/Kconfig"
+source "drivers/net/wireless/b43legacy/Kconfig"
source "drivers/net/wireless/hostap/Kconfig"
-source "drivers/net/wireless/bcm43xx/Kconfig"
+source "drivers/net/wireless/ipw2x00/Kconfig"
+source "drivers/net/wireless/iwlwifi/Kconfig"
+source "drivers/net/wireless/iwmc3200wifi/Kconfig"
+source "drivers/net/wireless/libertas/Kconfig"
+source "drivers/net/wireless/orinoco/Kconfig"
+source "drivers/net/wireless/p54/Kconfig"
+source "drivers/net/wireless/rt2x00/Kconfig"
+source "drivers/net/wireless/wl12xx/Kconfig"
source "drivers/net/wireless/zd1211rw/Kconfig"
-endmenu
+endif # WLAN