# Wireless LAN device configuration
#
-menu "Wireless LAN"
+menuconfig WLAN
+ bool "Wireless LAN"
depends on !S390
-
-config WLAN_PRE80211
- bool "Wireless LAN (pre-802.11)"
- depends on NETDEVICES
- ---help---
- Say Y if you have any pre-802.11 wireless LAN hardware.
-
- This option does not affect the kernel build, it only
- lets you choose drivers.
-
-config STRIP
- tristate "STRIP (Metricom starmode radio IP)"
- depends on INET && WLAN_PRE80211
- select WIRELESS_EXT
- ---help---
- Say Y if you have a Metricom radio and intend to use Starmode Radio
- IP. STRIP is a radio protocol developed for the MosquitoNet project
- (on the WWW at <http://mosquitonet.stanford.edu/>) to send Internet
- traffic using Metricom radios. Metricom radios are small, battery
- powered, 100kbit/sec packet radio transceivers, about the size and
- weight of a cellular telephone. (You may also have heard them called
- "Metricom modems" but we avoid the term "modem" because it misleads
- many people into thinking that you can plug a Metricom modem into a
- phone line and use it as a modem.)
-
- You can use STRIP on any Linux machine with a serial port, although
- it is obviously most useful for people with laptop computers. If you
- think you might get a Metricom radio in the future, there is no harm
- in saying Y to STRIP now, except that it makes the kernel a bit
- bigger.
-
- To compile this as a module, choose M here: the module will be
- called strip.
-
-config ARLAN
- tristate "Aironet Arlan 655 & IC2200 DS support"
- depends on ISA && !64BIT && WLAN_PRE80211
- select WIRELESS_EXT
- ---help---
- Aironet makes Arlan, a class of wireless LAN adapters. These use the
- www.Telxon.com chip, which is also used on several similar cards.
- This driver is tested on the 655 and IC2200 series cards. Look at
- <http://www.ylenurme.ee/~elmer/655/> for the latest information.
-
- The driver is built as two modules, arlan and arlan-proc. The latter
- is the /proc interface and is not needed most of time.
-
- On some computers the card ends up in non-valid state after some
- time. Use a ping-reset script to clear it.
-
-config WAVELAN
- tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support"
- depends on ISA && WLAN_PRE80211
- select WIRELESS_EXT
+ select WIRELESS
+ default y
---help---
- The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is
- a Radio LAN (wireless Ethernet-like Local Area Network) using the
- radio frequencies 900 MHz and 2.4 GHz.
-
- If you want to use an ISA WaveLAN card under Linux, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Some more specific
- information is contained in
- <file:Documentation/networking/wavelan.txt> and in the source code
- <file:drivers/net/wireless/wavelan.p.h>.
-
- You will also need the wireless tools package available from
- <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
- Please read the man pages contained therein.
-
- To compile this driver as a module, choose M here: the module will be
- called wavelan.
+ This section contains all the pre 802.11 and 802.11 wireless
+ device drivers. For a complete list of drivers and documentation
+ on them refer to the wireless wiki:
-config PCMCIA_WAVELAN
- tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support"
- depends on PCMCIA && WLAN_PRE80211
- select WIRELESS_EXT
- help
- Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA
- (PC-card) wireless Ethernet networking card to your computer. This
- driver is for the non-IEEE-802.11 Wavelan cards.
-
- To compile this driver as a module, choose M here: the module will be
- called wavelan_cs. If unsure, say N.
-
-config PCMCIA_NETWAVE
- tristate "Xircom Netwave AirSurfer Pcmcia wireless support"
- depends on PCMCIA && WLAN_PRE80211
- select WIRELESS_EXT
- help
- Say Y here if you intend to attach this type of PCMCIA (PC-card)
- wireless Ethernet networking card to your computer.
-
- To compile this driver as a module, choose M here: the module will be
- called netwave_cs. If unsure, say N.
+ http://wireless.kernel.org/en/users/Drivers
-
-config WLAN_80211
- bool "Wireless LAN (IEEE 802.11)"
- depends on NETDEVICES
- ---help---
- Say Y if you have any 802.11 wireless LAN hardware.
-
- This option does not affect the kernel build, it only
- lets you choose drivers.
+if WLAN
config PCMCIA_RAYCS
tristate "Aviator/Raytheon 2.4GHz wireless support"
- depends on PCMCIA && WLAN_80211
+ depends on PCMCIA
select WIRELESS_EXT
+ select WEXT_SPY
+ select WEXT_PRIV
---help---
Say Y here if you intend to attach an Aviator/Raytheon PCMCIA
(PC-card) wireless Ethernet networking card to your computer.
To compile this driver as a module, choose M here: the module will be
called ray_cs. If unsure, say N.
-config LIBERTAS
- tristate "Marvell 8xxx Libertas WLAN driver support"
- depends on WLAN_80211
- select WIRELESS_EXT
- select LIB80211
- select FW_LOADER
- ---help---
- A library for Marvell Libertas 8xxx devices.
-
-config LIBERTAS_USB
- tristate "Marvell Libertas 8388 USB 802.11b/g cards"
- depends on LIBERTAS && USB
- ---help---
- A driver for Marvell Libertas 8388 USB devices.
-
-config LIBERTAS_CS
- tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
- depends on LIBERTAS && PCMCIA
- select FW_LOADER
- ---help---
- A driver for Marvell Libertas 8385 CompactFlash devices.
-
-config LIBERTAS_SDIO
- tristate "Marvell Libertas 8385/8686/8688 SDIO 802.11b/g cards"
- depends on LIBERTAS && MMC
- ---help---
- A driver for Marvell Libertas 8385/8686/8688 SDIO devices.
-
-config LIBERTAS_SPI
- tristate "Marvell Libertas 8686 SPI 802.11b/g cards"
- depends on LIBERTAS && SPI
- ---help---
- A driver for Marvell Libertas 8686 SPI devices.
-
-config LIBERTAS_DEBUG
- bool "Enable full debugging output in the Libertas module."
- depends on LIBERTAS
- ---help---
- Debugging support.
-
config LIBERTAS_THINFIRM
tristate "Marvell 8xxx Libertas WLAN driver support with thin firmware"
- depends on WLAN_80211 && MAC80211
+ depends on MAC80211
select FW_LOADER
---help---
A library for Marvell Libertas 8xxx devices using thinfirm.
config AIRO
tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards"
- depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN)
+ depends on ISA_DMA_API && (PCI || BROKEN)
select WIRELESS_EXT
select CRYPTO
+ select WEXT_SPY
+ select WEXT_PRIV
---help---
This is the standard Linux driver to support Cisco/Aironet ISA and
PCI 802.11 wireless cards.
config ATMEL
tristate "Atmel at76c50x chipset 802.11b support"
- depends on (PCI || PCMCIA) && WLAN_80211
+ depends on (PCI || PCMCIA)
select WIRELESS_EXT
+ select WEXT_PRIV
select FW_LOADER
select CRC32
---help---
config AT76C50X_USB
tristate "Atmel at76c503/at76c505/at76c505a USB cards"
- depends on MAC80211 && WLAN_80211 && USB
+ depends on MAC80211 && USB
select FW_LOADER
---help---
Enable support for USB Wireless devices using Atmel at76c503,
config AIRO_CS
tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards"
- depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211
+ depends on PCMCIA && (BROKEN || !M32R)
select WIRELESS_EXT
+ select WEXT_SPY
select CRYPTO
select CRYPTO_AES
---help---
Cisco Linux utilities can be used to configure the card.
config PCMCIA_WL3501
- tristate "Planet WL3501 PCMCIA cards"
- depends on EXPERIMENTAL && PCMCIA && WLAN_80211
- select WIRELESS_EXT
- ---help---
- A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
- It has basic support for Linux wireless extensions and initial
- micro support for ethtool.
+ tristate "Planet WL3501 PCMCIA cards"
+ depends on EXPERIMENTAL && PCMCIA
+ select WIRELESS_EXT
+ select WEXT_SPY
+ help
+ A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
+ It has basic support for Linux wireless extensions and initial
+ micro support for ethtool.
config PRISM54
- tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus'
- depends on PCI && EXPERIMENTAL && WLAN_80211
+ tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus (DEPRECATED)'
+ depends on PCI && EXPERIMENTAL
select WIRELESS_EXT
+ select WEXT_SPY
+ select WEXT_PRIV
select FW_LOADER
---help---
- Enable PCI and Cardbus support for the following chipset based cards:
-
- ISL3880 - Prism GT 802.11 b/g
- ISL3877 - Prism Indigo 802.11 a
- ISL3890 - Prism Duette 802.11 a/b/g
-
- For a complete list of supported cards visit <http://prism54.org>.
- Here is the latest confirmed list of supported cards:
-
- 3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 (version 1)
- Allnet ALL0271 PCI Card
- Compex WL54G Cardbus Card
- Corega CG-WLCB54GT Cardbus Card
- D-Link Air Plus Xtreme G A1 Cardbus Card aka DWL-g650
- I-O Data WN-G54/CB Cardbus Card
- Kobishi XG-300 aka Z-Com Cardbus Card
- Netgear WG511 Cardbus Card
- Ovislink WL-5400PCI PCI Card
- Peabird WLG-PCI PCI Card
- Sitecom WL-100i Cardbus Card
- Sitecom WL-110i PCI Card
- SMC2802W - EZ Connect g 2.4GHz 54 Mbps Wireless PCI Card
- SMC2835W - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
- SMC2835W-V2 - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
- Z-Com XG-900 PCI Card
- Zyxel G-100 Cardbus Card
-
- If you enable this you will need a firmware file as well.
- You will need to copy this to /usr/lib/hotplug/firmware/isl3890.
- You can get this non-GPL'd firmware file from the Prism54 project page:
- <http://prism54.org>
- You will also need the /etc/hotplug/firmware.agent script from
- a current hotplug package.
-
- Note: You need a motherboard with DMA support to use any of these cards
-
- If you want to compile the driver as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want),
- say M here and read <file:Documentation/kbuild/modules.txt>.
- The module will be called prism54.
+ This enables support for FullMAC PCI/Cardbus prism54 devices. This
+ driver is now deprecated in favor for the SoftMAC driver, p54pci.
+ p54pci supports FullMAC PCI/Cardbus devices as well. For details on
+ the scheduled removal of this driver on the kernel see the feature
+ removal schedule:
+
+ Documentation/feature-removal-schedule.txt
+
+ For more information refer to the p54 wiki:
+
+ http://wireless.kernel.org/en/users/Drivers/p54
+
+ Note: You need a motherboard with DMA support to use any of these cards
+
+ When built as module you get the module prism54
config USB_ZD1201
tristate "USB ZD1201 based Wireless device support"
- depends on USB && WLAN_80211
+ depends on USB
select WIRELESS_EXT
+ select WEXT_PRIV
select FW_LOADER
---help---
Say Y if you want to use wireless LAN adapters based on the ZyDAS
config USB_NET_RNDIS_WLAN
tristate "Wireless RNDIS USB support"
- depends on USB && WLAN_80211 && EXPERIMENTAL
+ depends on USB && EXPERIMENTAL
depends on CFG80211
select USB_USBNET
select USB_NET_CDCETHER
select USB_NET_RNDIS_HOST
- select WIRELESS_EXT
---help---
This is a driver for wireless RNDIS devices.
These are USB based adapters found in devices such as:
config RTL8180
tristate "Realtek 8180/8185 PCI support"
- depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
+ depends on MAC80211 && PCI && EXPERIMENTAL
select EEPROM_93CX6
---help---
This is a driver for RTL8180 and RTL8185 based cards.
config RTL8187
tristate "Realtek 8187 and 8187B USB support"
- depends on MAC80211 && USB && WLAN_80211
+ depends on MAC80211 && USB
select EEPROM_93CX6
---help---
This is a driver for RTL8187 and RTL8187B based cards.
Micronet SP907GK V5
Encore ENUWI-G2
Trendnet TEW-424UB
- ASUS P5B Deluxe
+ ASUS P5B Deluxe/P5K Premium motherboards
Toshiba Satellite Pro series of laptops
Asus Wireless Link
Linksys WUSB54GC-EU v2
+ (v1 = rt73usb; v3 is rt2070-based,
+ use staging/rt3070 or try rt2800usb)
Thanks to Realtek for their support!
config ADM8211
tristate "ADMtek ADM8211 support"
- depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
+ depends on MAC80211 && PCI && EXPERIMENTAL
select CRC32
select EEPROM_93CX6
---help---
config MAC80211_HWSIM
tristate "Simulated radio testing tool for mac80211"
- depends on MAC80211 && WLAN_80211
+ depends on MAC80211
---help---
This driver is a developer testing tool that can be used to test
IEEE 802.11 networking stack (mac80211) functionality. This is not
config MWL8K
tristate "Marvell 88W8xxx PCI/PCIe Wireless support"
- depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
+ depends on MAC80211 && PCI && EXPERIMENTAL
---help---
This driver supports Marvell TOPDOG 802.11 wireless cards.
To compile this driver as a module, choose M here: the module
will be called mwl8k. If unsure, say N.
-source "drivers/net/wireless/p54/Kconfig"
source "drivers/net/wireless/ath/Kconfig"
-source "drivers/net/wireless/ipw2x00/Kconfig"
-source "drivers/net/wireless/iwlwifi/Kconfig"
-source "drivers/net/wireless/hostap/Kconfig"
source "drivers/net/wireless/b43/Kconfig"
source "drivers/net/wireless/b43legacy/Kconfig"
-source "drivers/net/wireless/zd1211rw/Kconfig"
-source "drivers/net/wireless/rt2x00/Kconfig"
+source "drivers/net/wireless/hostap/Kconfig"
+source "drivers/net/wireless/ipw2x00/Kconfig"
+source "drivers/net/wireless/iwlwifi/Kconfig"
+source "drivers/net/wireless/iwmc3200wifi/Kconfig"
+source "drivers/net/wireless/libertas/Kconfig"
source "drivers/net/wireless/orinoco/Kconfig"
+source "drivers/net/wireless/p54/Kconfig"
+source "drivers/net/wireless/rt2x00/Kconfig"
source "drivers/net/wireless/wl12xx/Kconfig"
-source "drivers/net/wireless/iwmc3200wifi/Kconfig"
+source "drivers/net/wireless/zd1211rw/Kconfig"
-endmenu
+endif # WLAN
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff