#include <linux/netdevice.h>
#include <linux/platform_device.h>
#include <linux/sched.h>
-#include <linux/slab.h>
#include <linux/timer.h>
-#include <linux/version.h>
#include <linux/bug.h>
#include <linux/bitops.h>
#include <linux/irq.h>
#include <linux/io.h>
+#include <linux/swab.h>
#include <linux/phy.h>
#include <linux/smsc911x.h>
+#include <linux/device.h>
#include "smsc911x.h"
#define SMSC_CHIPNAME "smsc911x"
smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
unsigned int wordcount)
{
+ if (pdata->config.flags & SMSC911X_SWAP_FIFO) {
+ while (wordcount--)
+ smsc911x_reg_write(pdata, TX_DATA_FIFO, swab32(*buf++));
+ return;
+ }
+
if (pdata->config.flags & SMSC911X_USE_32BIT) {
writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount);
return;
smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
unsigned int wordcount)
{
+ if (pdata->config.flags & SMSC911X_SWAP_FIFO) {
+ while (wordcount--)
+ *buf++ = swab32(smsc911x_reg_read(pdata, RX_DATA_FIFO));
+ return;
+ }
+
if (pdata->config.flags & SMSC911X_USE_32BIT) {
readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount);
return;
goto out;
}
- SMSC_WARNING(HW, "Timed out waiting for MII write to finish");
+ SMSC_WARNING(HW, "Timed out waiting for MII read to finish");
reg = -EIO;
out:
* usage is 10/100 indicator */
pdata->gpio_setting = smsc911x_reg_read(pdata,
GPIO_CFG);
- if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_)
- && (!pdata->using_extphy)) {
+ if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_) &&
+ (!pdata->using_extphy)) {
/* Force 10/100 LED off, after saving
* orginal GPIO configuration */
pdata->gpio_orig_setting = pdata->gpio_setting;
{
struct smsc911x_data *pdata = netdev_priv(dev);
struct phy_device *phydev = NULL;
- int phy_addr;
+ int ret;
/* find the first phy */
- for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) {
- if (pdata->mii_bus->phy_map[phy_addr]) {
- phydev = pdata->mii_bus->phy_map[phy_addr];
- SMSC_TRACE(PROBE, "PHY %d: addr %d, phy_id 0x%08X",
- phy_addr, phydev->addr, phydev->phy_id);
- break;
- }
- }
-
+ phydev = phy_find_first(pdata->mii_bus);
if (!phydev) {
pr_err("%s: no PHY found\n", dev->name);
return -ENODEV;
}
- phydev = phy_connect(dev, dev_name(&phydev->dev),
- &smsc911x_phy_adjust_link, 0, pdata->config.phy_interface);
+ SMSC_TRACE(PROBE, "PHY %d: addr %d, phy_id 0x%08X",
+ phy_addr, phydev->addr, phydev->phy_id);
+
+ ret = phy_connect_direct(dev, phydev,
+ &smsc911x_phy_adjust_link, 0,
+ pdata->config.phy_interface);
- if (IS_ERR(phydev)) {
+ if (ret) {
pr_err("%s: Could not attach to PHY\n", dev->name);
- return PTR_ERR(phydev);
+ return ret;
}
pr_info("%s: attached PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n",
SMSC_TRACE(HW, "Passed Loop Back Test");
#endif /* USE_PHY_WORK_AROUND */
- SMSC_TRACE(HW, "phy initialised succesfully");
+ SMSC_TRACE(HW, "phy initialised successfully");
return 0;
}
SMSC_WARNING(HW,
"Packet tag reserved bit is high");
} else {
- if (unlikely(tx_stat & 0x00008000)) {
+ if (unlikely(tx_stat & TX_STS_ES_)) {
dev->stats.tx_errors++;
} else {
dev->stats.tx_packets++;
dev->stats.tx_bytes += (tx_stat >> 16);
}
- if (unlikely(tx_stat & 0x00000100)) {
+ if (unlikely(tx_stat & TX_STS_EXCESS_COL_)) {
dev->stats.collisions += 16;
dev->stats.tx_aborted_errors += 1;
} else {
dev->stats.collisions +=
((tx_stat >> 3) & 0xF);
}
- if (unlikely(tx_stat & 0x00000800))
+ if (unlikely(tx_stat & TX_STS_LOST_CARRIER_))
dev->stats.tx_carrier_errors += 1;
- if (unlikely(tx_stat & 0x00000200)) {
+ if (unlikely(tx_stat & TX_STS_LATE_COL_)) {
dev->stats.collisions++;
dev->stats.tx_aborted_errors++;
}
{
int crc_err = 0;
- if (unlikely(rxstat & 0x00008000)) {
+ if (unlikely(rxstat & RX_STS_ES_)) {
dev->stats.rx_errors++;
- if (unlikely(rxstat & 0x00000002)) {
+ if (unlikely(rxstat & RX_STS_CRC_ERR_)) {
dev->stats.rx_crc_errors++;
crc_err = 1;
}
}
if (likely(!crc_err)) {
- if (unlikely((rxstat & 0x00001020) == 0x00001020)) {
- /* Frame type indicates length,
- * and length error is set */
+ if (unlikely((rxstat & RX_STS_FRAME_TYPE_) &&
+ (rxstat & RX_STS_LENGTH_ERR_)))
dev->stats.rx_length_errors++;
- }
if (rxstat & RX_STS_MCAST_)
dev->stats.multicast++;
}
do {
udelay(1);
val = smsc911x_reg_read(pdata, RX_DP_CTRL);
- } while (--timeout && (val & RX_DP_CTRL_RX_FFWD_));
+ } while ((val & RX_DP_CTRL_RX_FFWD_) && --timeout);
if (unlikely(timeout == 0))
SMSC_WARNING(HW, "Timed out waiting for "
struct net_device *dev = pdata->dev;
int npackets = 0;
- while (likely(netif_running(dev)) && (npackets < budget)) {
+ while (npackets < budget) {
unsigned int pktlength;
unsigned int pktwords;
struct sk_buff *skb;
/* Update counters */
dev->stats.rx_packets++;
dev->stats.rx_bytes += (pktlength - 4);
- dev->last_rx = jiffies;
}
/* Return total received packets */
/* Sets the device MAC address to dev_addr, called with mac_lock held */
static void
-smsc911x_set_mac_address(struct smsc911x_data *pdata, u8 dev_addr[6])
+smsc911x_set_hw_mac_address(struct smsc911x_data *pdata, u8 dev_addr[6])
{
u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4];
u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) |
/* Make sure EEPROM has finished loading before setting GPIO_CFG */
timeout = 50;
- while ((timeout--) &&
- (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_)) {
+ while ((smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) &&
+ --timeout) {
udelay(10);
}
/* The soft reset above cleared the device's MAC address,
* restore it from local copy (set in probe) */
spin_lock_irq(&pdata->mac_lock);
- smsc911x_set_mac_address(pdata, dev->dev_addr);
+ smsc911x_set_hw_mac_address(pdata, dev->dev_addr);
spin_unlock_irq(&pdata->mac_lock);
/* Initialise irqs, but leave all sources disabled */
dev_info(&dev->dev, "SMSC911x/921x identified at %#08lx, IRQ: %d\n",
(unsigned long)pdata->ioaddr, dev->irq);
+ /* Reset the last known duplex and carrier */
+ pdata->last_duplex = -1;
+ pdata->last_carrier = -1;
+
/* Bring the PHY up */
phy_start(pdata->phy_dev);
smsc911x_tx_writefifo(pdata, (unsigned int *)bufp, wrsz);
freespace -= (skb->len + 32);
dev_kfree_skb(skb);
- dev->trans_start = jiffies;
if (unlikely(smsc911x_tx_get_txstatcount(pdata) >= 30))
smsc911x_tx_update_txcounters(dev);
pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_HPFILT_);
pdata->hashhi = 0;
pdata->hashlo = 0;
- } else if (dev->mc_count > 0) {
+ } else if (!netdev_mc_empty(dev)) {
/* Enabling specific multicast addresses */
unsigned int hash_high = 0;
unsigned int hash_low = 0;
- unsigned int count = 0;
- struct dev_mc_list *mc_list = dev->mc_list;
+ struct netdev_hw_addr *ha;
pdata->set_bits_mask = MAC_CR_HPFILT_;
pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_MCPAS_);
- while (mc_list) {
- count++;
- if ((mc_list->dmi_addrlen) == ETH_ALEN) {
- unsigned int bitnum =
- smsc911x_hash(mc_list->dmi_addr);
- unsigned int mask = 0x01 << (bitnum & 0x1F);
- if (bitnum & 0x20)
- hash_high |= mask;
- else
- hash_low |= mask;
- } else {
- SMSC_WARNING(DRV, "dmi_addrlen != 6");
- }
- mc_list = mc_list->next;
+ netdev_for_each_mc_addr(ha, dev) {
+ unsigned int bitnum = smsc911x_hash(ha->addr);
+ unsigned int mask = 0x01 << (bitnum & 0x1F);
+
+ if (bitnum & 0x20)
+ hash_high |= mask;
+ else
+ hash_low |= mask;
}
- if (count != (unsigned int)dev->mc_count)
- SMSC_WARNING(DRV, "mc_count != dev->mc_count");
pdata->hashhi = hash_high;
pdata->hashlo = hash_low;
}
#endif /* CONFIG_NET_POLL_CONTROLLER */
+static int smsc911x_set_mac_address(struct net_device *dev, void *p)
+{
+ struct smsc911x_data *pdata = netdev_priv(dev);
+ struct sockaddr *addr = p;
+
+ /* On older hardware revisions we cannot change the mac address
+ * registers while receiving data. Newer devices can safely change
+ * this at any time. */
+ if (pdata->generation <= 1 && netif_running(dev))
+ return -EBUSY;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
+
+ spin_lock_irq(&pdata->mac_lock);
+ smsc911x_set_hw_mac_address(pdata, dev->dev_addr);
+ spin_unlock_irq(&pdata->mac_lock);
+
+ dev_info(&dev->dev, "MAC Address: %pM\n", dev->dev_addr);
+
+ return 0;
+}
+
/* Standard ioctls for mii-tool */
static int smsc911x_do_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
{
u8 address, u8 data)
{
u32 op = E2P_CMD_EPC_CMD_ERASE_ | address;
+ u32 temp;
int ret;
SMSC_TRACE(DRV, "address 0x%x, data 0x%x", address, data);
if (!ret) {
op = E2P_CMD_EPC_CMD_WRITE_ | address;
smsc911x_reg_write(pdata, E2P_DATA, (u32)data);
+
+ /* Workaround for hardware read-after-write restriction */
+ temp = smsc911x_reg_read(pdata, BYTE_TEST);
+
ret = smsc911x_eeprom_send_cmd(pdata, op);
}
.ndo_get_stats = smsc911x_get_stats,
.ndo_set_multicast_list = smsc911x_set_multicast_list,
.ndo_do_ioctl = smsc911x_do_ioctl,
+ .ndo_change_mtu = eth_change_mtu,
.ndo_validate_addr = eth_validate_addr,
- .ndo_set_mac_address = eth_mac_addr,
+ .ndo_set_mac_address = smsc911x_set_mac_address,
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = smsc911x_poll_controller,
#endif
if (!res)
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- release_mem_region(res->start, res->end - res->start);
+ release_mem_region(res->start, resource_size(res));
iounmap(pdata->ioaddr);
unsigned int intcfg = 0;
int res_size, irq_flags;
int retval;
- DECLARE_MAC_BUF(mac);
pr_info("%s: Driver version %s.\n", SMSC_CHIPNAME, SMSC_DRV_VERSION);
retval = -ENODEV;
goto out_0;
}
- res_size = res->end - res->start;
+ res_size = resource_size(res);
irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (!irq_res) {
/* Check if mac address has been specified when bringing interface up */
if (is_valid_ether_addr(dev->dev_addr)) {
- smsc911x_set_mac_address(pdata, dev->dev_addr);
+ smsc911x_set_hw_mac_address(pdata, dev->dev_addr);
SMSC_TRACE(PROBE, "MAC Address is specified by configuration");
+ } else if (is_valid_ether_addr(pdata->config.mac)) {
+ memcpy(dev->dev_addr, pdata->config.mac, 6);
+ SMSC_TRACE(PROBE, "MAC Address specified by platform data");
} else {
/* Try reading mac address from device. if EEPROM is present
* it will already have been set */
} else {
/* eeprom values are invalid, generate random MAC */
random_ether_addr(dev->dev_addr);
- smsc911x_set_mac_address(pdata, dev->dev_addr);
+ smsc911x_set_hw_mac_address(pdata, dev->dev_addr);
SMSC_TRACE(PROBE,
"MAC Address is set to random_ether_addr");
}
spin_unlock_irq(&pdata->mac_lock);
- dev_info(&dev->dev, "MAC Address: %s\n",
- print_mac(mac, dev->dev_addr));
+ dev_info(&dev->dev, "MAC Address: %pM\n", dev->dev_addr);
return 0;
out_free_netdev_2:
free_netdev(dev);
out_release_io_1:
- release_mem_region(res->start, res->end - res->start);
+ release_mem_region(res->start, resource_size(res));
out_0:
return retval;
}
+#ifdef CONFIG_PM
+/* This implementation assumes the devices remains powered on its VDDVARIO
+ * pins during suspend. */
+
+/* TODO: implement freeze/thaw callbacks for hibernation.*/
+
+static int smsc911x_suspend(struct device *dev)
+{
+ struct net_device *ndev = dev_get_drvdata(dev);
+ struct smsc911x_data *pdata = netdev_priv(ndev);
+
+ /* enable wake on LAN, energy detection and the external PME
+ * signal. */
+ smsc911x_reg_write(pdata, PMT_CTRL,
+ PMT_CTRL_PM_MODE_D1_ | PMT_CTRL_WOL_EN_ |
+ PMT_CTRL_ED_EN_ | PMT_CTRL_PME_EN_);
+
+ return 0;
+}
+
+static int smsc911x_resume(struct device *dev)
+{
+ struct net_device *ndev = dev_get_drvdata(dev);
+ struct smsc911x_data *pdata = netdev_priv(ndev);
+ unsigned int to = 100;
+
+ /* Note 3.11 from the datasheet:
+ * "When the LAN9220 is in a power saving state, a write of any
+ * data to the BYTE_TEST register will wake-up the device."
+ */
+ smsc911x_reg_write(pdata, BYTE_TEST, 0);
+
+ /* poll the READY bit in PMT_CTRL. Any other access to the device is
+ * forbidden while this bit isn't set. Try for 100ms and return -EIO
+ * if it failed. */
+ while (!(smsc911x_reg_read(pdata, PMT_CTRL) & PMT_CTRL_READY_) && --to)
+ udelay(1000);
+
+ return (to == 0) ? -EIO : 0;
+}
+
+static const struct dev_pm_ops smsc911x_pm_ops = {
+ .suspend = smsc911x_suspend,
+ .resume = smsc911x_resume,
+};
+
+#define SMSC911X_PM_OPS (&smsc911x_pm_ops)
+
+#else
+#define SMSC911X_PM_OPS NULL
+#endif
+
static struct platform_driver smsc911x_driver = {
.probe = smsc911x_drv_probe,
- .remove = smsc911x_drv_remove,
+ .remove = __devexit_p(smsc911x_drv_remove),
.driver = {
- .name = SMSC_CHIPNAME,
+ .name = SMSC_CHIPNAME,
+ .owner = THIS_MODULE,
+ .pm = SMSC911X_PM_OPS,
},
};