#ifndef _SKY2_H
#define _SKY2_H
-/* PCI device specific config registers */
+#define ETH_JUMBO_MTU 9000 /* Maximum MTU supported */
+
+/* PCI config registers */
enum {
PCI_DEV_REG1 = 0x40,
PCI_DEV_REG2 = 0x44,
+ PCI_DEV_STATUS = 0x7c,
PCI_DEV_REG3 = 0x80,
PCI_DEV_REG4 = 0x84,
PCI_DEV_REG5 = 0x88,
+ PCI_CFG_REG_0 = 0x90,
+ PCI_CFG_REG_1 = 0x94,
};
/* Yukon-2 */
enum pci_dev_reg_1 {
PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */
PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */
+ PCI_SW_PWR_ON_RST= 1<<30, /* SW Power on Reset (Yukon-EX) */
PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */
PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */
PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */
PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */
+ PCI_Y2_PME_LEGACY= 1<<15, /* PCI Express legacy power management mode */
+
+ PCI_PHY_LNK_TIM_MSK= 3L<<8,/* Bit 9.. 8: GPHY Link Trigger Timer */
+ PCI_ENA_L1_EVENT = 1<<7, /* Enable PEX L1 Event */
+ PCI_ENA_GPHY_LNK = 1<<6, /* Enable PEX L1 on GPHY Link down */
+ PCI_FORCE_PEX_L1 = 1<<5, /* Force to PEX L1 */
};
enum pci_dev_reg_2 {
/* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */
enum pci_dev_reg_4 {
- /* (Link Training & Status State Machine) */
+ /* (Link Training & Status State Machine) */
+ P_PEX_LTSSM_STAT_MSK = 0x7fL<<25, /* Bit 31..25: PEX LTSSM Mask */
+#define P_PEX_LTSSM_STAT(x) ((x << 25) & P_PEX_LTSSM_STAT_MSK)
+ P_PEX_LTSSM_L1_STAT = 0x34,
+ P_PEX_LTSSM_DET_STAT = 0x01,
P_TIMER_VALUE_MSK = 0xffL<<16, /* Bit 23..16: Timer Value Mask */
/* (Active State Power Management) */
P_FORCE_ASPM_REQUEST = 1<<15, /* Force ASPM Request (A1 only) */
| P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY,
};
+/* PCI_OUR_REG_5 32 bit Our Register 5 (Yukon-ECU only) */
+enum pci_dev_reg_5 {
+ /* Bit 31..27: for A3 & later */
+ P_CTL_DIV_CORE_CLK_ENA = 1<<31, /* Divide Core Clock Enable */
+ P_CTL_SRESET_VMAIN_AV = 1<<30, /* Soft Reset for Vmain_av De-Glitch */
+ P_CTL_BYPASS_VMAIN_AV = 1<<29, /* Bypass En. for Vmain_av De-Glitch */
+ P_CTL_TIM_VMAIN_AV_MSK = 3<<27, /* Bit 28..27: Timer Vmain_av Mask */
+ /* Bit 26..16: Release Clock on Event */
+ P_REL_PCIE_RST_DE_ASS = 1<<26, /* PCIe Reset De-Asserted */
+ P_REL_GPHY_REC_PACKET = 1<<25, /* GPHY Received Packet */
+ P_REL_INT_FIFO_N_EMPTY = 1<<24, /* Internal FIFO Not Empty */
+ P_REL_MAIN_PWR_AVAIL = 1<<23, /* Main Power Available */
+ P_REL_CLKRUN_REQ_REL = 1<<22, /* CLKRUN Request Release */
+ P_REL_PCIE_RESET_ASS = 1<<21, /* PCIe Reset Asserted */
+ P_REL_PME_ASSERTED = 1<<20, /* PME Asserted */
+ P_REL_PCIE_EXIT_L1_ST = 1<<19, /* PCIe Exit L1 State */
+ P_REL_LOADER_NOT_FIN = 1<<18, /* EPROM Loader Not Finished */
+ P_REL_PCIE_RX_EX_IDLE = 1<<17, /* PCIe Rx Exit Electrical Idle State */
+ P_REL_GPHY_LINK_UP = 1<<16, /* GPHY Link Up */
+
+ /* Bit 10.. 0: Mask for Gate Clock */
+ P_GAT_PCIE_RST_ASSERTED = 1<<10,/* PCIe Reset Asserted */
+ P_GAT_GPHY_N_REC_PACKET = 1<<9, /* GPHY Not Received Packet */
+ P_GAT_INT_FIFO_EMPTY = 1<<8, /* Internal FIFO Empty */
+ P_GAT_MAIN_PWR_N_AVAIL = 1<<7, /* Main Power Not Available */
+ P_GAT_CLKRUN_REQ_REL = 1<<6, /* CLKRUN Not Requested */
+ P_GAT_PCIE_RESET_ASS = 1<<5, /* PCIe Reset Asserted */
+ P_GAT_PME_DE_ASSERTED = 1<<4, /* PME De-Asserted */
+ P_GAT_PCIE_ENTER_L1_ST = 1<<3, /* PCIe Enter L1 State */
+ P_GAT_LOADER_FINISHED = 1<<2, /* EPROM Loader Finished */
+ P_GAT_PCIE_RX_EL_IDLE = 1<<1, /* PCIe Rx Electrical Idle State */
+ P_GAT_GPHY_LINK_DOWN = 1<<0, /* GPHY Link Down */
+
+ PCIE_OUR5_EVENT_CLK_D3_SET = P_REL_GPHY_REC_PACKET |
+ P_REL_INT_FIFO_N_EMPTY |
+ P_REL_PCIE_EXIT_L1_ST |
+ P_REL_PCIE_RX_EX_IDLE |
+ P_GAT_GPHY_N_REC_PACKET |
+ P_GAT_INT_FIFO_EMPTY |
+ P_GAT_PCIE_ENTER_L1_ST |
+ P_GAT_PCIE_RX_EL_IDLE,
+};
+
+#/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */
+enum pci_cfg_reg1 {
+ P_CF1_DIS_REL_EVT_RST = 1<<24, /* Dis. Rel. Event during PCIE reset */
+ /* Bit 23..21: Release Clock on Event */
+ P_CF1_REL_LDR_NOT_FIN = 1<<23, /* EEPROM Loader Not Finished */
+ P_CF1_REL_VMAIN_AVLBL = 1<<22, /* Vmain available */
+ P_CF1_REL_PCIE_RESET = 1<<21, /* PCI-E reset */
+ /* Bit 20..18: Gate Clock on Event */
+ P_CF1_GAT_LDR_NOT_FIN = 1<<20, /* EEPROM Loader Finished */
+ P_CF1_GAT_PCIE_RX_IDLE = 1<<19, /* PCI-E Rx Electrical idle */
+ P_CF1_GAT_PCIE_RESET = 1<<18, /* PCI-E Reset */
+ P_CF1_PRST_PHY_CLKREQ = 1<<17, /* Enable PCI-E rst & PM2PHY gen. CLKREQ */
+ P_CF1_PCIE_RST_CLKREQ = 1<<16, /* Enable PCI-E rst generate CLKREQ */
+
+ P_CF1_ENA_CFG_LDR_DONE = 1<<8, /* Enable core level Config loader done */
+
+ P_CF1_ENA_TXBMU_RD_IDLE = 1<<1, /* Enable TX BMU Read IDLE for ASPM */
+ P_CF1_ENA_TXBMU_WR_IDLE = 1<<0, /* Enable TX BMU Write IDLE for ASPM */
+
+ PCIE_CFG1_EVENT_CLK_D3_SET = P_CF1_DIS_REL_EVT_RST |
+ P_CF1_REL_LDR_NOT_FIN |
+ P_CF1_REL_VMAIN_AVLBL |
+ P_CF1_REL_PCIE_RESET |
+ P_CF1_GAT_LDR_NOT_FIN |
+ P_CF1_GAT_PCIE_RESET |
+ P_CF1_PRST_PHY_CLKREQ |
+ P_CF1_ENA_CFG_LDR_DONE |
+ P_CF1_ENA_TXBMU_RD_IDLE |
+ P_CF1_ENA_TXBMU_WR_IDLE,
+};
+
#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
PCI_STATUS_SIG_SYSTEM_ERROR | \
PCI_STATUS_REC_MASTER_ABORT | \
PCI_STATUS_REC_TARGET_ABORT | \
PCI_STATUS_PARITY)
+
enum csr_regs {
B0_RAP = 0x0000,
B0_CTST = 0x0004,
- B0_Y2LED = 0x0005,
+
B0_POWER_CTRL = 0x0007,
B0_ISRC = 0x0008,
B0_IMSK = 0x000c,
B3_PA_CTRL = 0x01f0,
B3_PA_TEST = 0x01f2,
- Y2_CFG_SPC = 0x1c00,
+ Y2_CFG_SPC = 0x1c00, /* PCI config space region */
+ Y2_CFG_AER = 0x1d00, /* PCI Advanced Error Report region */
};
-/* B0_CTST 16 bit Control/Status register */
+/* B0_CTST 24 bit Control/Status register */
enum {
Y2_VMAIN_AVAIL = 1<<17,/* VMAIN available (YUKON-2 only) */
Y2_VAUX_AVAIL = 1<<16,/* VAUX available (YUKON-2 only) */
CS_RST_SET = 1, /* Set Software reset */
};
-/* B0_LED 8 Bit LED register */
-enum {
-/* Bit 7.. 2: reserved */
- LED_STAT_ON = 1<<1, /* Status LED on */
- LED_STAT_OFF = 1, /* Status LED off */
-};
-
/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */
enum {
PC_VAUX_ENA = 1<<7, /* Switch VAUX Enable */
| Y2_IS_CHK_TXA1 | Y2_IS_CHK_RX1,
Y2_IS_PORT_2 = Y2_IS_IRQ_PHY2 | Y2_IS_IRQ_MAC2
| Y2_IS_CHK_TXA2 | Y2_IS_CHK_RX2,
+ Y2_IS_ERROR = Y2_IS_HW_ERR |
+ Y2_IS_IRQ_MAC1 | Y2_IS_CHK_TXA1 | Y2_IS_CHK_RX1 |
+ Y2_IS_IRQ_MAC2 | Y2_IS_CHK_TXA2 | Y2_IS_CHK_RX2,
};
/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
Y2_IS_PAR_RX2 | Y2_IS_TCP_TXS2| Y2_IS_TCP_TXA2,
Y2_HWE_ALL_MASK = Y2_IS_TIST_OV | Y2_IS_MST_ERR | Y2_IS_IRQ_STAT |
- Y2_IS_PCI_EXP |
Y2_HWE_L1_MASK | Y2_HWE_L2_MASK,
};
TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */
};
+/* B2_GPIO */
+enum {
+ GLB_GPIO_CLK_DEB_ENA = 1<<31, /* Clock Debug Enable */
+ GLB_GPIO_CLK_DBG_MSK = 0xf<<26, /* Clock Debug */
+
+ GLB_GPIO_INT_RST_D3_DIS = 1<<15, /* Disable Internal Reset After D3 to D0 */
+ GLB_GPIO_LED_PAD_SPEED_UP = 1<<14, /* LED PAD Speed Up */
+ GLB_GPIO_STAT_RACE_DIS = 1<<13, /* Status Race Disable */
+ GLB_GPIO_TEST_SEL_MSK = 3<<11, /* Testmode Select */
+ GLB_GPIO_TEST_SEL_BASE = 1<<11,
+ GLB_GPIO_RAND_ENA = 1<<10, /* Random Enable */
+ GLB_GPIO_RAND_BIT_1 = 1<<9, /* Random Bit 1 */
+};
+
/* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */
enum {
CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */
/* B2_CHIP_ID 8 bit Chip Identification Number */
enum {
- CHIP_ID_GENESIS = 0x0a, /* Chip ID for GENESIS */
- CHIP_ID_YUKON = 0xb0, /* Chip ID for YUKON */
- CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
- CHIP_ID_YUKON_LP = 0xb2, /* Chip ID for YUKON-LP */
- CHIP_ID_YUKON_XL = 0xb3, /* Chip ID for YUKON-2 XL */
- CHIP_ID_YUKON_EC_U = 0xb4, /* Chip ID for YUKON-2 EC Ultra */
- CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */
- CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */
-
+ CHIP_ID_YUKON_XL = 0xb3, /* YUKON-2 XL */
+ CHIP_ID_YUKON_EC_U = 0xb4, /* YUKON-2 EC Ultra */
+ CHIP_ID_YUKON_EX = 0xb5, /* YUKON-2 Extreme */
+ CHIP_ID_YUKON_EC = 0xb6, /* YUKON-2 EC */
+ CHIP_ID_YUKON_FE = 0xb7, /* YUKON-2 FE */
+ CHIP_ID_YUKON_FE_P = 0xb8, /* YUKON-2 FE+ */
+ CHIP_ID_YUKON_SUPR = 0xb9, /* YUKON-2 Supreme */
+ CHIP_ID_YUKON_UL_2 = 0xba, /* YUKON-2 Ultra 2 */
+};
+enum yukon_ec_rev {
CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */
CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */
CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */
-
- CHIP_REV_YU_EC_U_A0 = 0,
- CHIP_REV_YU_EC_U_A1 = 1,
};
+enum yukon_ec_u_rev {
+ CHIP_REV_YU_EC_U_A0 = 1,
+ CHIP_REV_YU_EC_U_A1 = 2,
+ CHIP_REV_YU_EC_U_B0 = 3,
+};
+enum yukon_fe_rev {
+ CHIP_REV_YU_FE_A1 = 1,
+ CHIP_REV_YU_FE_A2 = 2,
+};
+enum yukon_fe_p_rev {
+ CHIP_REV_YU_FE2_A0 = 0,
+};
+enum yukon_ex_rev {
+ CHIP_REV_YU_EX_A0 = 1,
+ CHIP_REV_YU_EX_B0 = 2,
+};
+enum yukon_supr_rev {
+ CHIP_REV_YU_SU_A0 = 0,
+};
+
/* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */
enum {
enum {
B8_Q_REGS = 0x0400, /* base of Queue registers */
Q_D = 0x00, /* 8*32 bit Current Descriptor */
- Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */
- Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */
+ Q_VLAN = 0x20, /* 16 bit Current VLAN Tag */
+ Q_DONE = 0x24, /* 16 bit Done Index */
Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */
Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */
Q_BC = 0x30, /* 32 bit Current Byte Counter */
Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */
- Q_F = 0x38, /* 32 bit Flag Register */
- Q_T1 = 0x3c, /* 32 bit Test Register 1 */
- Q_T1_TR = 0x3c, /* 8 bit Test Register 1 Transfer SM */
- Q_T1_WR = 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */
- Q_T1_RD = 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */
- Q_T1_SV = 0x3f, /* 8 bit Test Register 1 Supervisor SM */
- Q_T2 = 0x40, /* 32 bit Test Register 2 */
- Q_T3 = 0x44, /* 32 bit Test Register 3 */
+ Q_TEST = 0x38, /* 32 bit Test/Control Register */
/* Yukon-2 */
- Q_DONE = 0x24, /* 16 bit Done Index (Yukon-2 only) */
Q_WM = 0x40, /* 16 bit FIFO Watermark */
Q_AL = 0x42, /* 8 bit FIFO Alignment */
Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */
};
#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
-/* Q_F 32 bit Flag Register */
+/* Q_TEST 32 bit Test Register */
enum {
- F_ALM_FULL = 1<<27, /* Rx FIFO: almost full */
- F_EMPTY = 1<<27, /* Tx FIFO: empty flag */
- F_FIFO_EOF = 1<<26, /* Tag (EOF Flag) bit in FIFO */
- F_WM_REACHED = 1<<25, /* Watermark reached */
+ /* Transmit */
+ F_TX_CHK_AUTO_OFF = 1<<31, /* Tx checksum auto calc off (Yukon EX) */
+ F_TX_CHK_AUTO_ON = 1<<30, /* Tx checksum auto calc off (Yukon EX) */
+
+ /* Receive */
F_M_RX_RAM_DIS = 1<<24, /* MAC Rx RAM Read Port disable */
- F_FIFO_LEVEL = 0x1fL<<16, /* Bit 23..16: # of Qwords in FIFO */
- F_WATER_MARK = 0x0007ffL, /* Bit 10.. 0: Watermark */
+
+ /* Hardware testbits not used */
};
/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
PHY_ADDR_MARV = 0,
};
-#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
+#define RB_ADDR(offs, queue) ((u16) B16_RAM_REGS + (queue) + (offs))
enum {
BMU_FIFO_ENA | BMU_OP_ON,
BMU_WM_DEFAULT = 0x600,
+ BMU_WM_PEX = 0x80,
};
/* Tx BMU Control / Status Registers (Yukon-2) */
TX_GMF_RP = 0x0d70,/* 32 bit Tx GMAC FIFO Read Pointer */
TX_GMF_RSTP = 0x0d74,/* 32 bit Tx GMAC FIFO Restart Pointer */
TX_GMF_RLEV = 0x0d78,/* 32 bit Tx GMAC FIFO Read Level */
+
+ /* Threshold values for Yukon-EC Ultra and Extreme */
+ ECU_AE_THR = 0x0070, /* Almost Empty Threshold */
+ ECU_TXFF_LEV = 0x01a0, /* Tx BMU FIFO Level */
+ ECU_JUMBO_WM = 0x0080, /* Jumbo Mode Watermark */
};
/* Descriptor Poll Timer Registers */
POLL_LIST_ADDR_HI= 0x0e2c,/* 32 bit Poll. List Start Addr (high) */
};
+enum {
+ SMB_CFG = 0x0e40, /* 32 bit SMBus Config Register */
+ SMB_CSR = 0x0e44, /* 32 bit SMBus Control/Status Register */
+};
+
+enum {
+ CPU_WDOG = 0x0e48, /* 32 bit Watchdog Register */
+ CPU_CNTR = 0x0e4C, /* 32 bit Counter Register */
+ CPU_TIM = 0x0e50,/* 32 bit Timer Compare Register */
+ CPU_AHB_ADDR = 0x0e54, /* 32 bit CPU AHB Debug Register */
+ CPU_AHB_WDATA = 0x0e58, /* 32 bit CPU AHB Debug Register */
+ CPU_AHB_RDATA = 0x0e5C, /* 32 bit CPU AHB Debug Register */
+ HCU_MAP_BASE = 0x0e60, /* 32 bit Reset Mapping Base */
+ CPU_AHB_CTRL = 0x0e64, /* 32 bit CPU AHB Debug Register */
+ HCU_CCSR = 0x0e68, /* 32 bit CPU Control and Status Register */
+ HCU_HCSR = 0x0e6C, /* 32 bit Host Control and Status Register */
+};
+
/* ASF Subsystem Registers (Yukon-2 only) */
enum {
B28_Y2_SMB_CONFIG = 0x0e40,/* 32 bit ASF SMBus Config Register */
GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */
/* Wake-up Frame Pattern Match Control Registers (YUKON only) */
-
- WOL_REG_OFFS = 0x20,/* HW-Bug: Address is + 0x20 against spec. */
-
WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */
WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */
WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */
WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */
- WOL_PATT_PME = 0x0f2a,/* 8 bit WOL PME Match Enable (Yukon-2) */
- WOL_PATT_ASFM = 0x0f2b,/* 8 bit WOL ASF Match Enable (Yukon-2) */
WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */
/* WOL Pattern Length Registers (YUKON only) */
-
WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */
WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */
/* WOL Pattern Counter Registers (YUKON only) */
-
-
WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */
WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */
};
+#define WOL_REGS(port, x) (x + (port)*0x80)
enum {
WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */
WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */
};
+#define WOL_PATT_RAM_BASE(port) (WOL_PATT_RAM_1 + (port)*0x400)
enum {
BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */
PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */
};
-#define PHY_M_PC_MDI_XMODE(x) (((x)<<5) & PHY_M_PC_MDIX_MSK)
+#define PHY_M_PC_MDI_XMODE(x) (((u16)(x)<<5) & PHY_M_PC_MDIX_MSK)
enum {
PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */
PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */
};
+/* for Yukon-EC Ultra Gigabit Ethernet PHY (88E1149 only) */
+enum {
+ PHY_M_PC_COP_TX_DIS = 1<<3, /* Copper Transmitter Disable */
+ PHY_M_PC_POW_D_ENA = 1<<2, /* Power Down Enable */
+};
+
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
enum {
PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
PHY_M_IS_JABBER = 1<<0, /* Jabber */
PHY_M_DEF_MSK = PHY_M_IS_LSP_CHANGE | PHY_M_IS_LST_CHANGE
- | PHY_M_IS_FIFO_ERROR,
+ | PHY_M_IS_DUP_CHANGE,
PHY_M_AN_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL,
};
PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */
PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */};
-#define PHY_M_EC_M_DSC(x) ((x)<<10 & PHY_M_EC_M_DSC_MSK)
+#define PHY_M_EC_M_DSC(x) ((u16)(x)<<10 & PHY_M_EC_M_DSC_MSK)
/* 00=1x; 01=2x; 10=3x; 11=4x */
-#define PHY_M_EC_S_DSC(x) ((x)<<8 & PHY_M_EC_S_DSC_MSK)
+#define PHY_M_EC_S_DSC(x) ((u16)(x)<<8 & PHY_M_EC_S_DSC_MSK)
/* 00=dis; 01=1x; 10=2x; 11=3x */
-#define PHY_M_EC_DSC_2(x) ((x)<<9 & PHY_M_EC_M_DSC_MSK2)
+#define PHY_M_EC_DSC_2(x) ((u16)(x)<<9 & PHY_M_EC_M_DSC_MSK2)
/* 000=1x; 001=2x; 010=3x; 011=4x */
-#define PHY_M_EC_MAC_S(x) ((x)<<4 & PHY_M_EC_MAC_S_MSK)
+#define PHY_M_EC_MAC_S(x) ((u16)(x)<<4 & PHY_M_EC_MAC_S_MSK)
/* 01X=0; 110=2.5; 111=25 (MHz) */
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
};
/* !!! Errata in spec. (1 = disable) */
-#define PHY_M_PC_DSC(x) (((x)<<12) & PHY_M_PC_DSC_MSK)
+#define PHY_M_PC_DSC(x) (((u16)(x)<<12) & PHY_M_PC_DSC_MSK)
/* 100=5x; 101=6x; 110=7x; 111=8x */
enum {
MAC_TX_CLK_0_MHZ = 2,
PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */
};
-#define PHY_M_LED_PULS_DUR(x) (((x)<<12) & PHY_M_LEDC_PULS_MSK)
+#define PHY_M_LED_PULS_DUR(x) (((u16)(x)<<12) & PHY_M_LEDC_PULS_MSK)
/***** PHY_MARV_PHY_STAT (page 3)16 bit r/w Polarity Control Reg. *****/
enum {
PULS_1300MS = 7,/* 1.3 s to 2.7 s */
};
-#define PHY_M_LED_BLINK_RT(x) (((x)<<8) & PHY_M_LEDC_BL_R_MSK)
+#define PHY_M_LED_BLINK_RT(x) (((u16)(x)<<8) & PHY_M_LEDC_BL_R_MSK)
enum {
BLINK_42MS = 0,/* 42 ms */
};
/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
-#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
- /* Bit 13..12: reserved */
-#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
-#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
-#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
-#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
-#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
-#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
+#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
-enum {
- MO_LED_NORM = 0,
- MO_LED_BLINK = 1,
- MO_LED_OFF = 2,
- MO_LED_ON = 3,
+#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
+#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
+#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
+#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
+#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
+#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
+
+enum led_mode {
+ MO_LED_NORM = 0,
+ MO_LED_BLINK = 1,
+ MO_LED_OFF = 2,
+ MO_LED_ON = 3,
};
/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */
};
-#define PHY_M_FELP_LED2_CTRL(x) (((x)<<8) & PHY_M_FELP_LED2_MSK)
-#define PHY_M_FELP_LED1_CTRL(x) (((x)<<4) & PHY_M_FELP_LED1_MSK)
-#define PHY_M_FELP_LED0_CTRL(x) (((x)<<0) & PHY_M_FELP_LED0_MSK)
+#define PHY_M_FELP_LED2_CTRL(x) (((u16)(x)<<8) & PHY_M_FELP_LED2_MSK)
+#define PHY_M_FELP_LED1_CTRL(x) (((u16)(x)<<4) & PHY_M_FELP_LED1_MSK)
+#define PHY_M_FELP_LED0_CTRL(x) (((u16)(x)<<0) & PHY_M_FELP_LED0_MSK)
enum {
LED_PAR_CTRL_COLX = 0x00,
/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
enum {
PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */
+ PHY_M_MAC_GMIF_PUP = 1<<3, /* GMII Power Up (88E1149 only) */
PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */
PHY_M_MAC_MD_COPPER = 5,/* Copper only */
PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */
};
#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
-#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
/* GM_TX_CTRL 16 bit r/w Transmit Control Register */
enum {
GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */
};
-#define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK)
-#define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK)
+#define GM_SMI_CT_PHY_AD(x) (((u16)(x)<<11) & GM_SMI_CT_PHY_A_MSK)
+#define GM_SMI_CT_REG_AD(x) (((u16)(x)<<6) & GM_SMI_CT_REG_A_MSK)
/* GM_PHY_ADDR 16 bit r/w GPHY Address Register */
enum {
/* Receive Frame Status Encoding */
enum {
- GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */
+ GMR_FS_LEN = 0x7fff<<16, /* Bit 30..16: Rx Frame Length */
GMR_FS_VLAN = 1<<13, /* VLAN Packet */
GMR_FS_JABBER = 1<<12, /* Jabber Packet */
GMR_FS_UN_SIZE = 1<<11, /* Undersize Packet */
RX_VLAN_STRIP_ON = 1<<25, /* enable VLAN stripping */
RX_VLAN_STRIP_OFF = 1<<24, /* disable VLAN stripping */
+ RX_MACSEC_FLUSH_ON = 1<<23,
+ RX_MACSEC_FLUSH_OFF = 1<<22,
+ RX_MACSEC_ASF_FLUSH_ON = 1<<21,
+ RX_MACSEC_ASF_FLUSH_OFF = 1<<20,
+
+ GMF_RX_OVER_ON = 1<<19, /* enable flushing on receive overrun */
+ GMF_RX_OVER_OFF = 1<<18, /* disable flushing on receive overrun */
+ GMF_ASF_RX_OVER_ON = 1<<17, /* enable flushing of ASF when overrun */
+ GMF_ASF_RX_OVER_OFF = 1<<16, /* disable flushing of ASF when overrun */
+
GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */
GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */
GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */
GMF_RX_CTRL_DEF = GMF_OPER_ON | GMF_RX_F_FL_ON,
};
+/* TX_GMF_EA 32 bit Tx GMAC FIFO End Address */
+enum {
+ TX_DYN_WM_ENA = 3, /* Yukon-FE+ specific */
+};
/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */
enum {
TX_VLAN_TAG_ON = 1<<25,/* enable VLAN tagging */
TX_VLAN_TAG_OFF = 1<<24,/* disable VLAN tagging */
+ TX_JUMBO_ENA = 1<<23,/* PCI Jumbo Mode enable (Yukon-EC Ultra) */
+ TX_JUMBO_DIS = 1<<22,/* PCI Jumbo Mode enable (Yukon-EC Ultra) */
+
GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */
GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */
GMF_WSP_STEP = 1<<16,/* Write Shadow Pointer Step/Increment */
Y2_ASF_CLR_ASFI = 1<<1, /* Clear host IRQ */
Y2_ASF_HOST_IRQ = 1<<0, /* Issue an IRQ to HOST system */
};
+/* HCU_CCSR CPU Control and Status Register */
+enum {
+ HCU_CCSR_SMBALERT_MONITOR= 1<<27, /* SMBALERT pin monitor */
+ HCU_CCSR_CPU_SLEEP = 1<<26, /* CPU sleep status */
+ /* Clock Stretching Timeout */
+ HCU_CCSR_CS_TO = 1<<25,
+ HCU_CCSR_WDOG = 1<<24, /* Watchdog Reset */
+
+ HCU_CCSR_CLR_IRQ_HOST = 1<<17, /* Clear IRQ_HOST */
+ HCU_CCSR_SET_IRQ_HCU = 1<<16, /* Set IRQ_HCU */
+
+ HCU_CCSR_AHB_RST = 1<<9, /* Reset AHB bridge */
+ HCU_CCSR_CPU_RST_MODE = 1<<8, /* CPU Reset Mode */
+
+ HCU_CCSR_SET_SYNC_CPU = 1<<5,
+ HCU_CCSR_CPU_CLK_DIVIDE_MSK = 3<<3,/* CPU Clock Divide */
+ HCU_CCSR_CPU_CLK_DIVIDE_BASE= 1<<3,
+ HCU_CCSR_OS_PRSNT = 1<<2, /* ASF OS Present */
+/* Microcontroller State */
+ HCU_CCSR_UC_STATE_MSK = 3,
+ HCU_CCSR_UC_STATE_BASE = 1<<0,
+ HCU_CCSR_ASF_RESET = 0,
+ HCU_CCSR_ASF_HALTED = 1<<1,
+ HCU_CCSR_ASF_RUNNING = 1<<0,
+};
+
+/* HCU_HCSR Host Control and Status Register */
+enum {
+ HCU_HCSR_SET_IRQ_CPU = 1<<16, /* Set IRQ_CPU */
+
+ HCU_HCSR_CLR_IRQ_HCU = 1<<1, /* Clear IRQ_HCU */
+ HCU_HCSR_SET_IRQ_HOST = 1<<0, /* Set IRQ_HOST */
+};
/* STAT_CTRL 32 bit Status BMU control register (Yukon-2 only) */
enum {
/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */
enum {
+ GMC_SET_RST = 1<<15,/* MAC SEC RST */
+ GMC_SEC_RST_OFF = 1<<14,/* MAC SEC RSt OFF */
+ GMC_BYP_MACSECRX_ON = 1<<13,/* Bypass macsec RX */
+ GMC_BYP_MACSECRX_OFF= 1<<12,/* Bypass macsec RX off */
+ GMC_BYP_MACSECTX_ON = 1<<11,/* Bypass macsec TX */
+ GMC_BYP_MACSECTX_OFF= 1<<10,/* Bypass macsec TX off*/
+ GMC_BYP_RETR_ON = 1<<9, /* Bypass retransmit FIFO On */
+ GMC_BYP_RETR_OFF= 1<<8, /* Bypass retransmit FIFO Off */
+
GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */
GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */
GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */
/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */
enum {
- GPC_SEL_BDT = 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */
- GPC_INT_POL_HI = 1<<27, /* IRQ Polarity is Active HIGH */
- GPC_75_OHM = 1<<26, /* Use 75 Ohm Termination instead of 50 */
- GPC_DIS_FC = 1<<25, /* Disable Automatic Fiber/Copper Detection */
- GPC_DIS_SLEEP = 1<<24, /* Disable Energy Detect */
- GPC_HWCFG_M_3 = 1<<23, /* HWCFG_MODE[3] */
- GPC_HWCFG_M_2 = 1<<22, /* HWCFG_MODE[2] */
- GPC_HWCFG_M_1 = 1<<21, /* HWCFG_MODE[1] */
- GPC_HWCFG_M_0 = 1<<20, /* HWCFG_MODE[0] */
- GPC_ANEG_0 = 1<<19, /* ANEG[0] */
- GPC_ENA_XC = 1<<18, /* Enable MDI crossover */
- GPC_DIS_125 = 1<<17, /* Disable 125 MHz clock */
- GPC_ANEG_3 = 1<<16, /* ANEG[3] */
- GPC_ANEG_2 = 1<<15, /* ANEG[2] */
- GPC_ANEG_1 = 1<<14, /* ANEG[1] */
- GPC_ENA_PAUSE = 1<<13, /* Enable Pause (SYM_OR_REM) */
- GPC_PHYADDR_4 = 1<<12, /* Bit 4 of Phy Addr */
- GPC_PHYADDR_3 = 1<<11, /* Bit 3 of Phy Addr */
- GPC_PHYADDR_2 = 1<<10, /* Bit 2 of Phy Addr */
- GPC_PHYADDR_1 = 1<<9, /* Bit 1 of Phy Addr */
- GPC_PHYADDR_0 = 1<<8, /* Bit 0 of Phy Addr */
- /* Bits 7..2: reserved */
+ GPC_TX_PAUSE = 1<<30, /* Tx pause enabled (ro) */
+ GPC_RX_PAUSE = 1<<29, /* Rx pause enabled (ro) */
+ GPC_SPEED = 3<<27, /* PHY speed (ro) */
+ GPC_LINK = 1<<26, /* Link up (ro) */
+ GPC_DUPLEX = 1<<25, /* Duplex (ro) */
+ GPC_CLOCK = 1<<24, /* 125Mhz clock stable (ro) */
+
+ GPC_PDOWN = 1<<23, /* Internal regulator 2.5 power down */
+ GPC_TSTMODE = 1<<22, /* Test mode */
+ GPC_REG18 = 1<<21, /* Reg18 Power down */
+ GPC_REG12SEL = 3<<19, /* Reg12 power setting */
+ GPC_REG18SEL = 3<<17, /* Reg18 power setting */
+ GPC_SPILOCK = 1<<16, /* SPI lock (ASF) */
+
+ GPC_LEDMUX = 3<<14, /* LED Mux */
+ GPC_INTPOL = 1<<13, /* Interrupt polarity */
+ GPC_DETECT = 1<<12, /* Energy detect */
+ GPC_1000HD = 1<<11, /* Enable 1000Mbit HD */
+ GPC_SLAVE = 1<<10, /* Slave mode */
+ GPC_PAUSE = 1<<9, /* Pause enable */
+ GPC_LEDCTL = 3<<6, /* GPHY Leds */
+
GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */
GPC_RST_SET = 1<<0, /* Set GPHY Reset */
};
GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */
#define GMAC_DEF_MSK GM_IS_TX_FF_UR
+};
/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
- /* Bits 15.. 2: reserved */
+enum { /* Bits 15.. 2: reserved */
GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */
GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */
+};
/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */
+enum {
WOL_CTL_LINK_CHG_OCC = 1<<15,
WOL_CTL_MAGIC_PKT_OCC = 1<<14,
WOL_CTL_PATTERN_OCC = 1<<13,
WOL_CTL_DIS_PATTERN_UNIT = 1<<0,
};
-#define WOL_CTL_DEFAULT \
- (WOL_CTL_DIS_PME_ON_LINK_CHG | \
- WOL_CTL_DIS_PME_ON_PATTERN | \
- WOL_CTL_DIS_PME_ON_MAGIC_PKT | \
- WOL_CTL_DIS_LINK_CHG_UNIT | \
- WOL_CTL_DIS_PATTERN_UNIT | \
- WOL_CTL_DIS_MAGIC_PKT_UNIT)
-
-/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */
-#define WOL_CTL_PATT_ENA(x) (1 << (x))
-
/* Control flags */
enum {
OP_ADDR64VLAN = OP_ADDR64 | OP_VLAN,
OP_LRGLEN = 0x24,
OP_LRGLENVLAN = OP_LRGLEN | OP_VLAN,
+ OP_MSS = 0x28,
+ OP_MSSVLAN = OP_MSS | OP_VLAN,
+
OP_BUFFER = 0x40,
OP_PACKET = 0x41,
OP_LARGESEND = 0x43,
+ OP_LSOV2 = 0x45,
/* YUKON-2 STATUS opcodes defines */
OP_RXSTAT = 0x60,
OP_RXTIMEVLAN = OP_RXTIMESTAMP | OP_RXVLAN,
OP_RSS_HASH = 0x65,
OP_TXINDEXLE = 0x68,
+ OP_MACSEC = 0x6c,
+ OP_PUTIDX = 0x70,
+};
+
+enum status_css {
+ CSS_TCPUDPCSOK = 1<<7, /* TCP / UDP checksum is ok */
+ CSS_ISUDP = 1<<6, /* packet is a UDP packet */
+ CSS_ISTCP = 1<<5, /* packet is a TCP packet */
+ CSS_ISIPFRAG = 1<<4, /* packet is a TCP/UDP frag, CS calc not done */
+ CSS_ISIPV6 = 1<<3, /* packet is a IPv6 packet */
+ CSS_IPV4CSUMOK = 1<<2, /* IP v4: TCP header checksum is ok */
+ CSS_ISIPV4 = 1<<1, /* packet is a IPv4 packet */
+ CSS_LINK_BIT = 1<<0, /* port number (legacy) */
};
/* Yukon 2 hardware interface */
struct sky2_status_le {
__le32 status; /* also checksum */
__le16 length; /* also vlan tag */
- u8 link;
+ u8 css;
u8 opcode;
} __attribute((packed));
struct tx_ring_info {
struct sk_buff *skb;
+ unsigned long flags;
+#define TX_MAP_SINGLE 0x0001
+#define TX_MAP_PAGE 000002
DECLARE_PCI_UNMAP_ADDR(mapaddr);
- DECLARE_PCI_UNMAP_ADDR(maplen);
+ DECLARE_PCI_UNMAP_LEN(maplen);
};
struct rx_ring_info {
struct sk_buff *skb;
- dma_addr_t mapaddr;
+ dma_addr_t data_addr;
+ DECLARE_PCI_UNMAP_LEN(data_size);
+ dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
+};
+
+enum flow_control {
+ FC_NONE = 0,
+ FC_TX = 1,
+ FC_RX = 2,
+ FC_BOTH = 3,
};
struct sky2_port {
struct tx_ring_info *tx_ring;
struct sky2_tx_le *tx_le;
+ u16 tx_ring_size;
u16 tx_cons; /* next le to check */
u16 tx_prod; /* next le to use */
- u32 tx_addr64;
+ u16 tx_next; /* debug only */
+
u16 tx_pending;
u16 tx_last_mss;
+ u32 tx_last_upper;
u32 tx_tcpsum;
struct rx_ring_info *rx_ring ____cacheline_aligned_in_smp;
struct sky2_rx_le *rx_le;
- u32 rx_addr64;
+
u16 rx_next; /* next re to check */
u16 rx_put; /* next le index to use */
u16 rx_pending;
- u16 rx_bufsize;
+ u16 rx_data_size;
+ u16 rx_nfrags;
+
#ifdef SKY2_VLAN_TAG_USED
u16 rx_tag;
struct vlan_group *vlgrp;
#endif
+ struct {
+ unsigned long last;
+ u32 mac_rp;
+ u8 mac_lev;
+ u8 fifo_rp;
+ u8 fifo_lev;
+ } check;
dma_addr_t rx_le_map;
dma_addr_t tx_le_map;
- u32 advertising; /* ADVERTISED_ bits */
- u16 speed; /* SPEED_1000, SPEED_100, ... */
- u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
- u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
- u8 rx_pause;
- u8 tx_pause;
- u8 rx_csum;
- struct net_device_stats net_stats;
+ u16 advertising; /* ADVERTISED_ bits */
+ u16 speed; /* SPEED_1000, SPEED_100, ... */
+ u8 wol; /* WAKE_ bits */
+ u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
+ u16 flags;
+#define SKY2_FLAG_RX_CHECKSUM 0x0001
+#define SKY2_FLAG_AUTO_SPEED 0x0002
+#define SKY2_FLAG_AUTO_PAUSE 0x0004
+
+ enum flow_control flow_mode;
+ enum flow_control flow_status;
+#ifdef CONFIG_SKY2_DEBUG
+ struct dentry *debugfs;
+#endif
};
struct sky2_hw {
void __iomem *regs;
struct pci_dev *pdev;
+ struct napi_struct napi;
struct net_device *dev[2];
+ unsigned long flags;
+#define SKY2_HW_USE_MSI 0x00000001
+#define SKY2_HW_FIBRE_PHY 0x00000002
+#define SKY2_HW_GIGABIT 0x00000004
+#define SKY2_HW_NEWER_PHY 0x00000008
+#define SKY2_HW_RAM_BUFFER 0x00000010
+#define SKY2_HW_NEW_LE 0x00000020 /* new LSOv2 format */
+#define SKY2_HW_AUTO_TX_SUM 0x00000040 /* new IP decode for Tx */
+#define SKY2_HW_ADV_POWER_CTL 0x00000080 /* additional PHY power regs */
- int pm_cap;
- int err_cap;
u8 chip_id;
u8 chip_rev;
u8 pmd_type;
u32 st_idx;
dma_addr_t st_dma;
- struct timer_list idle_timer;
- int msi_detected;
+ struct timer_list watchdog_timer;
+ struct work_struct restart_work;
wait_queue_head_t msi_wait;
+
+ char irq_name[0];
};
static inline int sky2_is_copper(const struct sky2_hw *hw)
{
- return !(hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P');
+ return !(hw->flags & SKY2_HW_FIBRE_PHY);
}
/* Register accessor for memory mapped device */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff